Abstract: The effect of the blade tip geometry of a high pressure
gas turbine is studied experimentally and computationally for high
speed leakage flows. For this purpose two simplified models are
constructed, one models a flat tip of the blade and the second models
a cavity tip of the blade. Experimental results are obtained from a
transonic wind tunnel to show the static pressure distribution along
the tip wall and provide flow visualization. RANS computations
were carried to provide further insight into the mean flow behavior
and to calculate the discharge coefficient which is a measure of the
flow leaking over the tip. It is shown that in both geometries of tip
the flow separates over the tip to form a separation bubble. The
bubble is higher for the cavity tip while a complete shock wave
system of oblique waves ending with a normal wave can be seen for
the flat tip. The discharge coefficient for the flat tip shows less
dependence on the pressure ratio over the blade tip than the cavity
tip. However, the discharge coefficient for the cavity tip is lower than
that of the flat tip, showing a better ability to reduce the leakage flow
and thus increase the turbine efficiency.
Abstract: The objective of this paper is to a design of pattern
classification model based on the back-propagation (BP) algorithm for
decision support system. Standard BP model has done full connection
of each node in the layers from input to output layers. Therefore, it
takes a lot of computing time and iteration computing for good
performance and less accepted error rate when we are doing some
pattern generation or training the network.
However, this model is using exclusive connection in between
hidden layer nodes and output nodes. The advantage of this model is
less number of iteration and better performance compare with standard
back-propagation model. We simulated some cases of classification
data and different setting of network factors (e.g. hidden layer number
and nodes, number of classification and iteration). During our
simulation, we found that most of simulations cases were satisfied by
BP based using exclusive connection network model compared to
standard BP. We expect that this algorithm can be available to
identification of user face, analysis of data, mapping data in between
environment data and information.
Abstract: A number of competing methodologies have been developed
to identify genes and classify DNA sequences into coding
and non-coding sequences. This classification process is fundamental
in gene finding and gene annotation tools and is one of the most
challenging tasks in bioinformatics and computational biology. An
information theory measure based on mutual information has shown
good accuracy in classifying DNA sequences into coding and noncoding.
In this paper we describe a species independent iterative
approach that distinguishes coding from non-coding sequences using
the mutual information measure (MIM). A set of sixty prokaryotes is
used to extract universal training data. To facilitate comparisons with
the published results of other researchers, a test set of 51 bacterial
and archaeal genomes was used to evaluate MIM. These results
demonstrate that MIM produces superior results while remaining
species independent.
Abstract: Optical character recognition of cursive scripts
presents a number of challenging problems in both segmentation and
recognition processes in different languages, including Persian. In
order to overcome these problems, we use a newly developed Persian
word segmentation method and a recognition-based segmentation
technique to overcome its segmentation problems. This method is
robust as well as flexible. It also increases the system-s tolerances to
font variations. The implementation results of this method on a
comprehensive database show a high degree of accuracy which meets
the requirements for commercial use. Extended with a suitable pre
and post-processing, the method offers a simple and fast framework
to develop a full OCR system.
Abstract: In this paper we present a photo mosaic smartphone
application in client-server based large-scale image databases. Photo
mosaic is not a new concept, but there are very few smartphone
applications especially for a huge number of images in the
client-server environment. To support large-scale image databases,
we first propose an overall framework working as a client-server
model. We then present a concept of image-PAA features to efficiently
handle a huge number of images and discuss its lower bounding
property. We also present a best-match algorithm that exploits the
lower bounding property of image-PAA. We finally implement an
efficient Android-based application and demonstrate its feasibility.
Abstract: This paper presents anapproach of hybridizing two or more artificial intelligence (AI) techniques which arebeing used to
fuzzify the workstress level ranking and categorize the rating accordingly. The use of two or more techniques (hybrid approach)
has been considered in this case, as combining different techniques may lead to neutralizing each other-s weaknesses generating a
superior hybrid solution. Recent researches have shown that there is a
need for a more valid and reliable tools, for assessing work stress. Thus artificial intelligence techniques have been applied in this
instance to provide a solution to a psychological application. An overview about the novel and autonomous interactive model for analysing work-stress that has been developedusing multi-agent
systems is also presented in this paper. The establishment of the intelligent multi-agent decision analyser (IMADA) using hybridized technique of neural networks and fuzzy logic within the multi-agent based framework is also described.
Abstract: Selecting the data modeling technique for an
information system is determined by the objective of the resultant
data model. Dimensional modeling is the preferred modeling
technique for data destined for data warehouses and data mining,
presenting data models that ease analysis and queries which are in
contrast with entity relationship modeling. The establishment of data
warehouses as components of information system landscapes in
many organizations has subsequently led to the development of
dimensional modeling. This has been significantly more developed
and reported for the commercial database management systems as
compared to the open sources thereby making it less affordable for
those in resource constrained settings. This paper presents
dimensional modeling of HIV patient information using open source
modeling tools. It aims to take advantage of the fact that the most
affected regions by the HIV virus are also heavily resource
constrained (sub-Saharan Africa) whereas having large quantities of
HIV data. Two HIV data source systems were studied to identify
appropriate dimensions and facts these were then modeled using two
open source dimensional modeling tools. Use of open source would
reduce the software costs for dimensional modeling and in turn make
data warehousing and data mining more feasible even for those in
resource constrained settings but with data available.
Abstract: Scarcity of water resources and huge costs of
establishing new hydraulic installations necessitate optimal
exploitation from existing reservoirs. Sustainable management and
efficient exploitation from existing finite water resources are
important factors in water resource management, particularly in the
periods of water insufficiency and in dry regions, and on account of
competitive allocations in the view of exploitation management. This
study aims to minimize reservoir water release from a determined
rate of demand. A numerical model for water optimal exploitation
has been developed using GAMS introduced by the World Bank and
applied to the case of Meijaran dam, northern Iran. The results
indicate that this model can optimize the function of reservoir
exploitation while required water for lower parts of the region will be
supplied. Further, allocating optimal water from reservoir, the
optimal rate of water allocated to any group of the users were
specified to increase benefits in curve dam exploitation.
Abstract: Energy and exergy study of air-water combined solar collector which is called dual purpose solar collector (DPSC) is investigated. The method of ε - NTU is used. Analysis is performed for triangle channels. Parameters like the air flow rate and water inlet temperature are studied. Results are shown that DPSC has better energy and exergy efficiency than single collector. In addition, the triangle passage with water inlet temperature of 60O C has shown better exergy and energy efficiency.
Abstract: When trying to enumerate all BIBD-s for given parameters,
their natural solution space appears to be huge and grows extremely with the number of points of the design. Therefore,
constructive enumerations are often carried out by assuming additional
constraints on design-s structure, automorphisms being mostly used ones. It remains a hard task to construct designs with trivial
automorphism group – those with no additional symmetry – although it is believed that most of the BIBD-s belong to that case. In
this paper, very many new designs with parameters 2-(13, 5, 5), 2-(16, 6, 5) and 2-(21, 6, 4) are constructed, assuming an action of an
automorphism of order 3. Even more, it was possible to construct millions of such designs with no non-trivial automorphisms.
Abstract: Fatigue behaviors of Lead Zirconate Titanate (PZT)
ceramics under different amplitude of bipolar electrical loads have
been investigated. Fatigue behavior is represented by the change of
hysteresis loops and remnant polarization. Three levels of electrical
load amplitudes (1.00, 1.25 and 1.50 kV /mm) were applied in this
experimental. It was found that the remnant polarization decreased
significantly with the number of loading cycles. The degree of fatigue
degradation depends on the amplitude of electric field. The higher
amplitude exhibits the greater fatigue degradation.
Abstract: In this paper we have proposed three and two
stage still gray scale image compressor based on BTC. In our
schemes, we have employed a combination of four techniques
to reduce the bit rate. They are quad tree segmentation, bit
plane omission, bit plane coding using 32 visual patterns and
interpolative bit plane coding. The experimental results show
that the proposed schemes achieve an average bit rate of 0.46
bits per pixel (bpp) for standard gray scale images with an
average PSNR value of 30.25, which is better than the results
from the exiting similar methods based on BTC.
Abstract: The purpose of this study was to investigate relationships between satisfaction with major and career decision efficacy and career attitude maturity of engineering college students by performing correlation analysis. Gender differences in between satisfaction with major and career decision efficacy and career attitude maturity were also examined by T-test. The results T-test revealed gender differences in only career decision efficacy. Male Students scored significantly higher than did female students on career decision efficacy and satisfaction with major. The results of correlation analysis showed a) satisfaction with major were significantly associated with career decision efficacy, b) satisfaction with major were significantly associated with career attitude maturity, and c) career decision efficacy were significantly associated with career attitude maturity. As a result,we found the importance of satisfaction in engineering college students- major studies when deciding their career.
Abstract: Benefits to the organisation are just as important as technical ability when it comes to software success. The challenge is to provide industry with professionals who understand this. In other words: How to teach computer engineering students to look beyond technology, and at the benefits of software to organizations? This paper reports on the conceptual design of a section of the computer networks module aimed to sensitize the students to the organisational context.
Checkland focuses on different worldviews represented by various role players in the organisation. He developed the Soft Systems Methodology that guides purposeful action in organisations, while incorporating different worldviews in the modeling process. If we can sensitize students to these methods, they are likely to appreciate the wider context of application of system software. This paper will provide literature on these concepts as well as detail on how the students will be guided to adopt these concepts.
Abstract: During last decades is widely discussed the
international harmonization of financial reporting. This
harmonization is also affected by national tax systems in analyzed
countries. This paper provides some evidence on current national tax
systems in selected countries in Central and Eastern Europe. The
linkage of accounting profit as a tax base might decrease the
administrative burden for majority of SMEs, which are the most
important engine of each national economy.
Abstract: e-mail has become an important means of electronic
communication but the viability of its usage is marred by Unsolicited
Bulk e-mail (UBE) messages. UBE consists of many types
like pornographic, virus infected and 'cry-for-help' messages as well
as fake and fraudulent offers for jobs, winnings and medicines. UBE
poses technical and socio-economic challenges to usage of e-mails.
To meet this challenge and combat this menace, we need to
understand UBE. Towards this end, the current paper presents a
content-based textual analysis of more than 2700 body enhancement
medicinal UBE. Technically, this is an application of Text Parsing
and Tokenization for an un-structured textual document and we
approach it using Bag Of Words (BOW) and Vector Space Document
Model techniques. We have attempted to identify the most
frequently occurring lexis in the UBE documents that advertise
various products for body enhancement. The analysis of such top
100 lexis is also presented. We exhibit the relationship between
occurrence of a word from the identified lexis-set in the given UBE
and the probability that the given UBE will be the one advertising for
fake medicinal product. To the best of our knowledge and survey of
related literature, this is the first formal attempt for identification of
most frequently occurring lexis in such UBE by its textual analysis.
Finally, this is a sincere attempt to bring about alertness against and
mitigate the threat of such luring but fake UBE.
Abstract: Legionella pneumophila is involved in more than 95%
cases of severe atypical pneumonia. Infection is mainly by
inhalation the indoor aerosols through the water-coolant systems.
Because some Legionella strains may be viable but not culturable,
therefore, Taq polymerase, DNA amplification and semi-nested-PCR
were carried out to detect Legionella-specific 16S-rDNA sequence.
For this purpose, 1.5 litter of water samples from 77 water-coolant
system were collected from four different hospitals, two nursing
homes and one student hostel in Kerman city of Iran, each in a brand
new plastic bottle during summer season of 2006 (from April to
August). The samples were filtered in the sterile condition through
the Millipore Membrane Filter. DNA was extracted from membrane
and used for PCR to detect Legionella spp. The PCR product was
then subjected to semi-nested PCR for detection of L. pneumophila.
Out of 77 water samples that were tested by PCR, 30 (39%) were
positive for most species of Legionella. However, L. pneumophila
was detected from 14 (18.2%) water samples by semi-nested PCR.
From the above results it can be concluded that water coolant
systems of different hospitals and nursing homes in Kerman city of
Iran are highly contaminated with L. pneumophila spp. and pose
serious concern. So, we recommend avoiding such type of coolant
system in the hospitals and nursing homes.
Abstract: Exact expressions for bit-error probability (BEP) for
coherent square detection of uncoded and coded M-ary quadrature
amplitude modulation (MQAM) using an array of antennas with
maximal ratio combining (MRC) in a flat fading channel interference
limited system in a Nakagami-m fading environment is derived. The
analysis assumes an arbitrary number of independent and identically
distributed Nakagami interferers. The results for coded MQAM are
computed numerically for the case of (24,12) extended Golay code
and compared with uncoded MQAM by plotting error probabilities
versus average signal-to-interference ratio (SIR) for various values of
order of diversity N, number of distinct symbols M, in order to
examine the effect of cochannel interferers on the performance of the
digital communication system. The diversity gains and net gains are
also presented in tabular form in order to examine the performance of
digital communication system in the presence of interferers, as the
order of diversity increases. The analytical results presented in this
paper are expected to provide useful information needed for design
and analysis of digital communication systems with space diversity
in wireless fading channels.
Abstract: This article presents a performance comparison of an
interior mounted permanent magnet synchronous generator (IPMSG)
with a synchronous reluctance generator (SynRG) with the same size
for a wind application. It is found that using the same geometrical
dimensions, a SynRG can convert 74 % of the power that an IPMSG
can convert, while it has 80% of the IPMSG weight. Moreover it is
found that the efficieny for the IMPSG is 99% at rated power
compared to 98.7% for the SynRG.
Abstract: Fuzzy Load forecasting plays a paramount role in the operation and management of power systems. Accurate estimation of future power demands for various lead times facilitates the task of generating power reliably and economically. The forecasting of future loads for a relatively large lead time (months to few years) is studied here (long term load forecasting). Among the various techniques used in forecasting load, artificial intelligence techniques provide greater accuracy to the forecasts as compared to conventional techniques. Fuzzy Logic, a very robust artificial intelligent technique, is described in this paper to forecast load on long term basis. The paper gives a general algorithm to forecast long term load. The algorithm is an Extension of Short term load forecasting method to Long term load forecasting and concentrates not only on the forecast values of load but also on the errors incorporated into the forecast. Hence, by correcting the errors in the forecast, forecasts with very high accuracy have been achieved. The algorithm, in the paper, is demonstrated with the help of data collected for residential sector (LT2 (a) type load: Domestic consumers). Load, is determined for three consecutive years (from April-06 to March-09) in order to demonstrate the efficiency of the algorithm and to forecast for the next two years (from April-09 to March-11).