Abstract: Mega urban transport projects (MUTPs) are
increasingly being used in urban environments to ameliorate the
problem of congestion. However, a number of problems with regard
to mega projects have been identified. In particular the seemingly
institutionalised over estimation of economic benefits and persistent
cost over runs, could mean that the wrong projects are selected, and
that the projects that are selected cost more than they should. Studies
to date have produced a number of solutions to these problems,
perhaps most notably, the various methods for the inclusion of the
private sector in project provision. However the problems have
shown significant intractability in the face of these solutions. This
paper provides a detailed examination of some of the problems
facing mega projects and then examines Foucault-s theory of
'governmentality' as a possible frame of analysis which might shed
light on the intractability of the problems that have been identified,
through an identification of the art of government in which MUTPs
occur.
Abstract: The counter flow solar air heaters, with four
transverse fins and wire mesh layers are constructed and investigated
experimentally for thermal efficiency at a geographic location of
Cyprus in the city of Famagusta. The absorber plate is replaced by
sixteen steel wire mesh layers, 0.18 x 0.18cm in cross section
opening and a 0.02cm in diameter. The wire mesh layers arranged in
three groups, first and second include 6 layers, while the third include
4 layers. All layers fixed in the duct parallel to the glazing and each
group separated from the others by wood frame thickness of 0.5cm to
reduce the pressure drop. The transverse fins arranged in a way to
force the air to flow through the bed like eight letter path with flow
depth 3cm. The proposed design has increased the heat transfer rate,
but on other hand causes a high pressure drop. The obtained results
show that, for air mass flow rate range between 0.011-0.036kg/s, the
thermal efficiency increases with increasing the air mass flow. The
maximum efficiency obtained is 65.6% for the mass flow rate of
0.036kg/s. Moreover, the temperature difference between the outlet
flow and the ambient temperature, ΔT, reduces as the air mass flow
rate increase. The maximum difference between the outlet and
ambient temperature obtained was 43°C for double pass for minimum
mass flow rate of 0.011kg/s. Comparison with a conventional solar
air heater collector shows a significantly development in the thermal
efficiency.
Abstract: In manufacturing industries, development of measurement leads to increase the number of monitoring variables and eventually the importance of multivariate control comes to the fore. Statistical process control (SPC) is one of the most widely used as multivariate control chart. Nevertheless, SPC is restricted to apply in processes because its assumption of data as following specific distribution. Unfortunately, process data are composed by the mixture of several processes and it is hard to estimate as one certain distribution. To alternative conventional SPC, therefore, nonparametric control chart come into the picture because of the strength of nonparametric control chart, the absence of parameter estimation. SVDD based control chart is one of the nonparametric control charts having the advantage of flexible control boundary. However,basic concept of SVDD has been an oversight to the important of data characteristic, density distribution. Therefore, we proposed DW-SVDD (Density Weighted SVDD) to cover up the weakness of conventional SVDD. DW-SVDD makes a new attempt to consider dense of data as introducing the notion of density Weight. We extend as control chart using new proposed SVDD and a simulation study of various distributional data is conducted to demonstrate the improvement of performance.
Abstract: Fractional Fourier Transform is a generalization of the classical Fourier Transform which is often symbolized as the rotation in time- frequency plane. Similar to the product of time and frequency span which provides the Uncertainty Principle for the classical Fourier domain, there has not been till date an Uncertainty Principle for the Fractional Fourier domain for a generalized class of finite energy signals. Though the lower bound for the product of time and Fractional Fourier span is derived for the real signals, a tighter lower bound for a general class of signals is of practical importance, especially for the analysis of signals containing chirps. We hence formulate a mathematical derivation that gives the lower bound of time and Fractional Fourier span product. The relation proves to be utmost importance in taking the Fractional Fourier Transform with adaptive time and Fractional span resolutions for a varied class of complex signals.
Abstract: Carbon dioxide capture process has been simulated
and studied under different process conditions. It has been shown
that several process parameters such as lean amine temperature,
number of adsorber stages, number of stripper stages and stripper
pressure affect different process conditions and outputs such as
carbon dioxide removal and reboiler duty. It may be concluded that
the simulation of carbon dioxide capture process can help to estimate
the best process conditions.
Abstract: The changing economic climate has made global
manufacturing a growing reality over the last decade, forcing
companies from east and west and all over the world to
collaborate beyond geographic boundaries in the design,
manufacture and assemble of products. The ISO10303 and
ISO14649 Standards (STEP and STEP-NC) have been
developed to introduce interoperability into manufacturing
enterprises so as to meet the challenge of responding to
production on demand. This paper describes and illustrates a
STEP compliant CAD/CAPP/CAM System for the manufacture
of rotational parts on CNC turning centers. The information
models to support the proposed system together with the data
models defined in the ISO14649 standard used to create the NC
programs are also described. A structured view of a STEP
compliant CAD/CAPP/CAM system framework supporting the
next generation of intelligent CNC controllers for turn/mill
component manufacture is provided. Finally a proposed
computational environment for a STEP-NC compliant system
for turning operations (SCSTO) is described. SCSTO is the
experimental part of the research supported by the specification
of information models and constructed using a structured
methodology and object-oriented methods. SCSTO was
developed to generate a Part 21 file based on machining
features to support the interactive generation of process plans
utilizing feature extraction. A case study component has been
developed to prove the concept for using the milling and turning
parts of ISO14649 to provide a turn-mill CAD/CAPP/CAM
environment.
Abstract: The demand on High voltage (HV) infrastructures is growing due to the corresponding growth in industries and population. New or upgraded HV infrastructure has safety implications since Transmission mains usually occupy the same easement in the vicinity of neighbouring residents. Transmission mains consist of underground (UG) and overhead (OH) sections and the transition between the UG and OH section is known as the UGOH pole. The existence of two transmission mains in the same easement can dictate to resort to more complicated earthing design in order to mitigate the effect of AC interference, and in some cases it can also necessitates completing a Split Study of the system. This paper provides an overview of the AC interference, Split Study and the earthing of an underground feeder including the UGOH pole .In addition, this paper discusses the use of different link boxes on the UG feeder and presents a case study that represent a clear example of the Ac interference and Split factor. Finally, a few recommendations are provided to achieve a safety zone in the area beyond the boundary of the HV system.
Abstract: This paper presents an iterative algorithm to find a
inverse kinematic solution of 5-DOF robot. The algorithm is to
minimize the iteration number. Since the 5-DOF robot cannot give full
orientation of tool. Only z-direction of tool is satisfied while rotation
of tool is determined by kinematic constraint. This work therefore
described how to specify the tool direction and let the tool rotation free.
The simulation results show that this algorithm effectively worked.
Using the proposed iteration algorithm, error due to inverse kinematics
converged to zero rapidly in 5 iterations. This algorithm was applied in
real welding robot and verified through various practical works.
Abstract: Decision Support System (DSS) are interactive
software systems that are built to assist the management of an
organization in the decision making process when faced with nonroutine
problems in a specific application domain. Non-functional
requirements (NFRs) for a DSS deal with the desirable qualities and
restrictions that the DSS functionalities must satisfy. Unlike the
functional requirements, which are tangible functionalities provided
by the DSS, NFRs are often hidden and transparent to DSS users but
affect the quality of the provided functionalities. NFRs are often
overlooked or added later to the system in an ad hoc manner, leading
to a poor overall quality of the system. In this paper, we discuss the
development of NFRs as part of the requirements engineering phase
of the system development life cycle of DSSs. To help eliciting
NFRs, we provide a comprehensive taxonomy of NFRs for DSSs.
Abstract: The focus of this paper is to construct daily time series
exchange rate forecast models of Samoan Tala/USD and Tala/AUD
during the year 2008 to 2012 with neural network The performance
of the models was measured by using varies error functions such as
Root Square mean error (RSME), Mean absolute error (MAE), and
Mean absolute percentage error (MAPE). Our empirical findings
suggest that AR (1) model is an effective tool to forecast the
Tala/USD and Tala/AUD.
Abstract: A DC servomotor position control system using a Fuzzy Logic Sliding mode Model Following Control or FLSMFC approach is presented. The FLSMFC structure consists of an integrator and variable structure system. The integral control is introduced into it in order to eliminated steady state error due to step and ramp command inputs and improve control precision, while the fuzzy control would maintain the insensitivity to parameter variation and disturbances. The FLSMFC strategy is implemented and applied to a position control of a DC servomotor drives. Experimental results indicated that FLSMFC system performance with respect to the sensitivity to parameter variations is greatly reduced. Also, excellent control effects and avoids the chattering phenomenon.
Abstract: The performance of modified Fenton (MF) treatment
to promote PAH oxidation in artificially contaminated soil was
investigated in packed soil column with a hydrogen peroxide (H2O2)
delivery system simulating in situ injection. Soil samples were spiked
with phenanthrene (low molecular weight PAH) and fluoranthene
(high molecular weight PAH) to an initial concentration of 500
mg/kg dried soil each. The effectiveness of process parameters
H2O2/soil, iron/soil, chelating agent/soil weight ratios and reaction
time were studied using a 24 three level factorial design experiments.
Statistically significant quadratic models were developed using
Response Surface Methodology (RSM) for degrading PAHs from the
soil samples. Optimum operating condition was achieved at mild
range of H2O2/soil, iron/soil and chelating agent/soil weight ratios,
indicating cost efficient method for treating highly contaminated
lands.
Abstract: This paper presents the development of a hybrid
thermal model for the EVO Electric AFM 140 Axial Flux Permanent
Magnet (AFPM) machine as used in hybrid and electric vehicles. The
adopted approach is based on a hybrid lumped parameter and finite
difference method. The proposed method divides each motor
component into regular elements which are connected together in a
thermal resistance network representing all the physical connections
in all three dimensions. The element shape and size are chosen
according to the component geometry to ensure consistency. The
fluid domain is lumped into one region with averaged heat transfer
parameters connecting it to the solid domain. Some model parameters
are obtained from Computation Fluid Dynamic (CFD) simulation and
empirical data. The hybrid thermal model is described by a set of
coupled linear first order differential equations which is discretised
and solved iteratively to obtain the temperature profile. The
computation involved is low and thus the model is suitable for
transient temperature predictions. The maximum error in temperature
prediction is 3.4% and the mean error is consistently lower than the
mean error due to uncertainty in measurements. The details of the
model development, temperature predictions and suggestions for
design improvements are presented in this paper.
Abstract: Microwave energy can be used for drying purpose. It is unique process. It is distinctly different from conventional drying process. It is advantageous over conventional drying / heating processes. When microwave energy is used for drying purpose, the process can be accelerated with a better control to achieve uniform heating, more conversion efficiency, selective drying and ultimately improved product quality of the output. Also, less floor space and compact system are the added advantages. Existing low power microwave drying system is to be modified with suitable applicator. Appropriate sensors are to be used to measure parameters like moisture, temperature, weight of sample. Suitable high tech controller is to be used to control microwave power continuously from minimum to maximum. Phase - controller, cycle - controller and PWM - controller are some of the advanced power control techniques. It has been proposed to work on turmeric using high-tech phase controller to control the microwave power conveniently. The drying of turmeric with microwave energy employing phase controller gives better results as formulated in this paper and hence new approach of processing turmeric will open future doors of profit making to allied industries and the farmers.
Abstract: The quality-of-service (QoS) support for wireless
LANs has been a hot research topic during the past few years. In this paper, two QoS provisioning mechanisms are proposed for the employment in 802.11e EDCA MAC scheme. First, the proposed call
admission control mechanism can not only guarantee the QoS for the higher priority existing connections but also provide the minimum reserved bandwidth for traffic flows with lower priority. In addition, the adaptive contention window adjustment mechanism can adjust the
maximum and minimum contention window size dynamically according to the existing connection number of each AC. The collision
probability as well as the packet delay will thus be reduced effectively.
Performance results via simulations have revealed the enhanced QoS property achieved by employing these two mechanisms.
Abstract: The paper structures research approaches to the crisis
and its management. It focuses on approaches – psychological,
sociological, economic, ethical and technological. Furthermore, it
describes the basic features of models chosen according to those
approaches. By their comparison it shows how the crisis influences
organizations and individuals, and their mutual interaction.
Abstract: Scheduling algorithm is a key technology in satellite
switching system with input-buffer. In this paper, a new scheduling
algorithm and its realization are proposed. Based on Crossbar
switching fabric, the algorithm adopts serial scheduling strategy and
adjusts the output port arbitrating strategy for the better equity of every
port. Consequently, it increases the matching probability. The
algorithm can greatly reduce the scheduling delay and cell loss rate.
The analysis and simulation results by OPNET show that the proposed
algorithm has the better performance than others in average delay and
cell loss rate, and has the equivalent complexity. On the basis of these
results, the hardware realization and simulation based on FPGA are
completed, which validate the feasibility of the new scheduling
algorithm.
Abstract: an intelligent BRT system is necessary when
communities looking for new ways to use high capacity rapid transit
at a reduced cost.This paper will describe the intelligent control
system that works with Datacenter. With the help of GPS system, the
data center can monitor the situation of each bus and bus station.
Through RFID technology, bus station and traffic light can transfer
data with bus and by Wimax communication technology all of parts
can talk together; data center learns all information about the location
of bus, the arrival of bus in each station and the number of passengers
in station and bus.Finally, the paper presents the case study of those
theories in Tehran BRT.
Abstract: Image segmentation is an important step in image
processing. Major developments in medical imaging allow
physicians to use potent and non-invasive methods in order to
evaluate structures, performance and to diagnose human diseases. In
this study, an active contour was used to extract vessel networks
from color retina images. Automatic analysis of retina vessels
facilitates calculation of arterial index which is required to diagnose
some certain retinopathies.
Abstract: The primary objective of this research is to improve the flexural capacity of FRP strengthened RC Beam structures with Aluminum and Titanium laminates. FRP rupture of flexural strengthened RC beams using FRP plates generally occurs at the interface between FRP plate and the beam. Therefore, in order to prevent brittle rupture and improve the ductility of the system, this research was performed by using Aluminum and Titanium materials between the two different structural systems. The research also aims to provide various strengthening/retrofitting methods for RC beam structures and to conduct a preliminary analysis of the demands on the structural systems. This was achieved by estimation using the experimental data from this research to identify a flexural capacity for the systems. Ultimately, the preliminary analysis of current study showed that the flexural capacity and system demand ductility was significantly improved by the systems inserted with Aluminum and Titanium anchor plates. Further verification of the experimental research is currently on its way to develop a new or reliable design guideline to retrofit/strengthen the concrete-FRP structural system can be evaluated.