Abstract: This paper presents a simple and effective method for approximate indexing of instances for instance based learning. The method uses an interval tree to determine a good starting search point for the nearest neighbor. The search stops when an early stopping criterion is met. The method proved to be very effective especially when only the first nearest neighbor is required.
Abstract: The RANS method with Saffman-s turbulence model
was employed to solve the time-dependent turbulent Navier-Stokes
and energy equations for oscillating pipe flows. The method of
partial sums of the Fourier series is used to analyze the harmonic
velocity and temperature results. The complete structures of the
oscillating pipe flows and the averaged Nusselt numbers on the tube
wall are provided by numerical simulation over wide ranges of ReA
and ReR. Present numerical code is validated by comparing the
laminar flow results to analytic solutions and turbulence flow results
to published experimental data at lower and higher Reynolds
numbers respectively. The effects of ReA and ReR on the velocity,
temperature and Nusselt number distributions have been di scussed.
The enhancement of the heat transfer due to oscillating flows has
also been presented. By the way of analyzing the overall Nusselt
number over wide ranges of the Reynolds number Re and Keulegan-
Carpenter number KC, the optimal ratio of the tube diameter over
the oscillation amplitude is obtained based on the existence of a
nearly constant optimal KC number. The potential application of the
present results in sea water cooling has also been discussed.
Abstract: We propose photo-BJMOSFET (Bipolar Junction Metal-Oxide-Semiconductor Field Effect Transistor) fabricated on SOI film. ITO film is adopted in the device as gate electrode to reduce light absorption. I-V characteristics of photo-BJMOSFET obtained in dark (dark current) and under 570nm illumination (photo current) are studied furthermore to achieve high photo-to-dark-current contrast ratio. Two variables in the calculation were the channel length and the thickness of the film which were set equal to six different values, i.e., L=2, 4, 6, 8, 10, and 12μm and three different values, i.e., dsi =100, 200 and 300nm, respectively. The results indicate that the greatest photo-to-dark-current contrast ratio is achieved with L=10μm and dsi=200 nm at VGK=0.6V.
Abstract: The improvement of irrigation systems in the Nile
Delta is one of the most important attempts in Egypt to implement
more effective irrigation technology by improving the existing
irrigation networks. Demand delivery system in the existing irrigation
network is using of mechanical gates structures to automatically
divert water from one portion of an agricultural field to another in the
desired amount and sequence. This paper discusses evaluating main
irrigation networks system under the government managed before
and after improvement systems in the Nile Delta. The overall results
indicate that policy of using the demand delivery concept through
irrigation networks is successful by improving water delivery
performance among them than the rotation delivery concept that used
before. It is provided fair share of water delivery among irrigation
districts and available water in the end of irrigation network,
although this system located in an end of irrigation networks in the
Nile Delta.
Abstract: Content-Based Image Retrieval has been a major area
of research in recent years. Efficient image retrieval with high
precision would require an approach which combines usage of both
the color and texture features of the image. In this paper we propose
a method for enhancing the capabilities of texture based feature
extraction and further demonstrate the use of these enhanced texture
features in Texture-Based Color Image Retrieval.
Abstract: This paper shows the results obtained in the analysis
of the impact of distributed generation (DG) on distribution losses
and presents a new algorithm to the optimal allocation of distributed
generation resources in distribution networks. The optimization is
based on a Hybrid Genetic Algorithm and Particle Swarm
Optimization (HGAPSO) aiming to optimal DG allocation in
distribution network. Through this algorithm a significant
improvement in the optimization goal is achieved. With a numerical
example the superiority of the proposed algorithm is demonstrated in
comparison with the simple genetic algorithm.
Abstract: An ordered porous antimony-doped tin oxide (ATO) film was successfully prepared using a simple coating process with colloidal templates. The facile production was effective when a combination of 16-nm ATO (as a model of an inorganic nanoparticle) and polystyrene (PS) spheres (as a model of the template) weresimply coated to produce a composite ATO/PS film. Heat treatment was then used to remove the PS and produce the porous film. The porous film with a spherical pore shape and a highly ordered porous structure could be obtained. A potential way for the control of pore size could be also achieved by changing initial template size. The theoretical explanation and mechanism of porous formation were also added, which would be important for the scaling-up prediction and estimation.
Abstract: Nowadays there are many methods for representing
knowledge such as semantic network, neural network, and conceptual
graphs. Nonetheless, these methods are not sufficiently efficient
when applied to perform and deduce on knowledge domains about
supporting in general education such as algebra, analysis or plane
geometry. This leads to the introduction of computational network
which is a useful tool for representation knowledge base, especially
for computational knowledge, especially knowledge domain about
general education. However, when dealing with a practical problem,
we often do not immediately find a new solution, but we search
related problems which have been solved before and then proposing
an appropriate solution for the problem. Besides that, when finding
related problems, we have to determine whether the result of them
can be used to solve the practical problem or not. In this paper, the
extension model of computational network has been presented. In this
model, Sample Problems, which are related problems, will be used
like the experience of human about practical problem, simulate the
way of human thinking, and give the good solution for the practical
problem faster and more effectively. This extension model is applied
to construct an automatic system for solving algebraic problems in
middle school.
Abstract: The compatibility of optical resonators with microfluidic systems may be relevant for chemical and biological applications. Here, a fluorescent-core microcavity (FCM) is investigated as a refractometric sensor for heavy oils. A high-index film of silicon quantum dots (QDs) was formed inside the capillary, supporting cylindrical fluorescence whispering gallery modes (WGMs). A set of standard refractive index oils was injected into a capillary, causing a shift of the WGM resonances toward longer wavelengths. A maximum sensitivity of 240 nm/RIU (refractive index unit) was found for a nominal oil index of 1.74. As well, a sensitivity of 22 nm/RIU was obtained for a lower index of 1.48, more typical of fuel hydrocarbons. Furthermore, the observed spectra and sensitivities were compared to theoretical predictions and reproduced via FDTD simulations, showing in general an excellent agreement. This work demonstrates the potential use of FCMs for oil sensing applications and the more generally for detecting liquid solutions with a high refractive index or high viscosity.
Abstract: Heat pipes are two-phase heat transfer devices with
high effective thermal conductivity. Due to the high heat transport
capacity, heat exchanger with heat pipes has become much smaller
than traditional heat exchangers in handling high heat fluxes. With
the working fluid in a heat pipe, heat can be absorbed on the
evaporator region and transported to the condenser region where the
vapour condenses releasing the heat to the cooling media. Heat pipe
technology has found increasing applications in enhancing the
thermal performance of heat exchangers in microelectranics, energy
saving in HVAC systems for operating rooms,surgery centers, hotels,
cleanrooms etc, temperature regulation systems for the human body
and other industrial sectors. Development activity in heat pipe and
thermosyphon technology in asia in recent years is surveyed. Some
new results obtained in Australia and other countries are also
included.
Abstract: New regulations and standards for noise emission increasingly compel the automotive firms to make some improvements about decreasing the engine noise. Nowadays, the perforated reactive mufflers which have an effective damping capability are specifically used for this purpose. New designs should be analyzed with respect to both acoustics and back pressure. In this study, a reactive perforated muffler is investigated numerically and experimentally. For an acoustical analysis, the transmission loss which is independent of sound source of the present cross flow, the perforated muffler was analyzed by COMSOL. To be able to validate the numerical results, transmission loss was measured experimentally. Back pressure was obtained based on the flow field analysis and was also compared with experimental results. Numerical results have an approximate error of 20% compared to experimental results.
Abstract: The aim of the present study was to investigate the
chemical and biological properties of local cowpea seed protein
cultivated in Gizan region. The results showed that the cowpea and
its products contain high level of protein (22.9-77.6%), high
carbohydrates (9.4-64.3%) and low fats (0.1-0.3%). The trypsin and
chymotrypsin activities were found to be 32.2 and 15.2 units,
respectively. These activities were not affected in both defatted and
protein concentrate whereas they were significantly reduced in
isolated protein and cooked samples. The phytate content of cooked
and concentrated cowpea samples varied from 0.25% -0.32%,
respectively. Tannin content was found to be 0.4% and 0.23% for
cooked and raw samples, respectively. The in vitro protein
digestibility was very high in cowpea seeds (75.04-78.76%). The
biological evaluation using rats showed that the group fed with
animal feed containing casein gain more weight than those fed with
that containing cowpea. However, the group fed with cooked cowpea
gain more weight than those fed with uncooked cowpea. On the
other hand, in vivo digestion showed high value (98.33%) among the
group consumed casein compared to other groups those consumed
cowpea contains feed. This could be attributed to low antinutritional
factors in casein contains feed compared to those of cowpea contains
feed because cooking significantly increased the digestion rate
(80.8% to 83.5%) of cowpea contains feed. Furthermore, the
biological evaluation was high (91.67%) of casein containing feed
compared to that of cowpea containing feed (80.83%-87.5%). The
net protein utilization (NPU) was higher (89.67%) in the group fed
with casein containing feed than that of cowpea containing feed
(56.33%-69.67%).
Abstract: The State of Rio de Janeiro, Brazil, will hold two important events in the nearby future. In 2014 it will have the final game of the Football World Cup, and in 2016 it will be holding the Olympic Games. Therefore, the public transportation system (mainly buses) is of a major concern to the Rio de Janeiro State authorities-. The main objective of this work is to compare the quality of service of the bus companies operating in the cities of ItaperunaandCampos, both cities situated in the state of Rio de Janeiro, Brazil. The outcome of thiscomparison, based on the opinion of the bus users, has shownthemdispleased with the quality of the service provided by the bus companies operating in both cities. It is urgent the need to find possible practical alternatives to minimize the consequences of the main problems detected in this work. With these practical alternatives available, we will be able to offer to the Rio de Janeiro State authorities- suggestions about possible solutions to the main problems identified in this survey, as well as the time of implantation and costs of these solutions.
Abstract: Principally, plants grown in soilless culture may be
attacked by the same pests and diseases as cultivated traditionally in
soil. The most destructive phytopathogens are fungi, such as
Phythium, Phytophthora and Fusarium, followed by viruses, bacteria
and nematodes. We investigated effect of carbon nanotube filters on
disease management of soilless culture. Tomato seedlings transplant
in plastic pots filled with a soilless media of vermiculite. The crop
irrigated and fertilized using a hydroponic nutrient solution. We used
carbon nanotube filters for nutrient solution disinfection. Our results
show that carbon nanotube filtration significantly reduces pathogens
on tomato plants. Fungal elimination (Fusarium oxysporum and
Pythium spp.) was usually successful at about 96 to 99.9% all over
the cultural season. It is seem that in tomato soilless culture,
nanofiltration constitutes a reliable method that allows control of the
development of diseases caused by pathogenic fungi
Abstract: Enzymatic hydrolysis of starch from natural sources
finds potential application in commercial production of alcoholic
beverage and bioethanol. In this study the effect of starch
concentration, temperature, time and enzyme concentration were
studied and optimized for hydrolysis of Potato starch powder (of
mesh 80/120) into glucose syrup by immobilized (using Sodium
arginate) α-amylase using central composite design. The
experimental result on enzymatic hydrolysis of Potato starch was
subjected to multiple linear regression analysis using MINITAB 14
software. Positive linear effect of starch concentration, enzyme
concentration and time was observed on hydrolysis of Potato starch
by α-amylase. The statistical significance of the model was validated
by F-test for analysis of variance (p ≤ 0.01). The optimum value of
starch concentration, enzyme concentration, temperature, time and
were found to be 6% (w/v), 2% (w/v), 40°C and 80min respectively.
The maximum glucose yield at optimum condition was 2.34 mg/mL.
Abstract: Two Amphiphilic catalysts, iron (III) dodecylbenzene
sulfonate and nickel (II) dodecylbenzene sulfonate, were synthesized
and used in the catalytic aquathermolysis of heavy crude oil to reduce
its viscosity. The prepared catalysts exhibited good performance in
the aquathermolysis and the viscosity is reduced by ~ 78.9 % for
Egyptian heavy crude oil. The chemical and physical properties of
heavy oil both before and after reaction were investigated by FT-IR,
dynamic viscosity, molecular weight and SARA analysis. The results
indicated that the content of resin, asphaltene, average molecular
weight and sulfur content of heavy oil is reduced after the catalytic
aquathermolysis.
Abstract: Conceptualization strengthens intelligent systems in generalization skill, effective knowledge representation, real-time inference, and managing uncertain and indefinite situations in addition to facilitating knowledge communication for learning agents situated in real world. Concept learning introduces a way of abstraction by which the continuous state is formed as entities called concepts which are connected to the action space and thus, they illustrate somehow the complex action space. Of computational concept learning approaches, action-based conceptualization is favored because of its simplicity and mirror neuron foundations in neuroscience. In this paper, a new biologically inspired concept learning approach based on the probabilistic framework is proposed. This approach exploits and extends the mirror neuron-s role in conceptualization for a reinforcement learning agent in nondeterministic environments. In the proposed method, instead of building a huge numerical knowledge, the concepts are learnt gradually from rewards through interaction with the environment. Moreover the probabilistic formation of the concepts is employed to deal with uncertain and dynamic nature of real problems in addition to the ability of generalization. These characteristics as a whole distinguish the proposed learning algorithm from both a pure classification algorithm and typical reinforcement learning. Simulation results show advantages of the proposed framework in terms of convergence speed as well as generalization and asymptotic behavior because of utilizing both success and failures attempts through received rewards. Experimental results, on the other hand, show the applicability and effectiveness of the proposed method in continuous and noisy environments for a real robotic task such as maze as well as the benefits of implementing an incremental learning scenario in artificial agents.
Abstract: A multi-rate discrete-time model, whose response
agrees exactly with that of a continuous-time original at all sampling
instants for any sampling periods, is developed for a linear system,
which is assumed to have multiple real eigenvalues. The sampling
rates can be chosen arbitrarily and individually, so that their ratios
can even be irrational. The state space model is obtained as a
combination of a linear diagonal state equation and a nonlinear output
equation. Unlike the usual lifted model, the order of the proposed
model is the same as the number of sampling rates, which is less than
or equal to the order of the original continuous-time system. The
method is based on a nonlinear variable transformation, which can be
considered as a generalization of linear similarity transformation,
which cannot be applied to systems with multiple eigenvalues in
general. An example and its simulation result show that the proposed
multi-rate model gives exact responses at all sampling instants.
Abstract: The significance of emissions from the road transport
sector (such as air pollution, noise, etc) has grown considerably in
recent years. In Australia, 14.3% of national greenhouse gas
emissions in 2000 were the transport sector-s share which 12.9% of
net national emissions were related to a road transport alone.
Considering the growing attention to the green house gas(GHG)
emissions, this paper attempts to provide air pollution modeling
aspects of environmental consequences of the road transport by using
one of the best computer based tools including the Geographic
Information System (GIS). In other word, in this study, GIS and its
applications is explained, models which are used to model air
pollution and GHG emissions from vehicles are described and GIS is
applied in real case study that attempts to forecast GHG emission
from people who travel to work by car in 2031 in Melbourne for
analysing results as thematic maps.
Abstract: In this paper, the innovative intelligent fuzzy weighted
input estimation method (FWIEM) can be applied to the inverse heat
transfer conduction problem (IHCP) to estimate the unknown
time-varying heat flux efficiently as presented. The feasibility of this
method can be verified by adopting the temperature measurement
experiment. We would like to focus attention on the heat flux
estimation to three kinds of samples (Copper, Iron and Steel/AISI 304)
with the same 3mm thickness. The temperature measurements are then
regarded as the inputs into the FWIEM to estimate the heat flux. The
experiment results show that the proposed algorithm can estimate the
unknown time-varying heat flux on-line.