Abstract: To investigate the behavior of sheet metals during
forming tailor welded blanks (TWB) of various thickness made via
Co2 Laser welding are under consideration. These blanks are formed
used two different forming methods of rubber as well as the
conventional punch and die methods. The main research objective is
the effects of using a rubber die instead of a solid one the
displacement of the weld line and the press force needed for forming.
Specimens with thicknesses of 0.5, 0.6, 0.8 and 1mm are subjected to
Erichsen two dimensional tests and the resulted force for each case
are compared. This is followed by a theoretical and numerical study
of press force and weld line displacement. It is concluded that using
rubber pad forming (RPF) causes a reduction in weld line
displacement and an increase in the press force.
Abstract: Pearson-s correlation coefficient and sequential path
analysis has been used for determining the interrelationship among
yield, yield components, soil minerals and aroma of Khao Dawk Mali
(KDML) 105 rice grown in the area of Tungkularonghai in Roi-Et
province, located in the northeast of Thailand. Pearson-s correlation
coefficient in this study showed that the number of panicles was the
only factor that had positive significant (0.790**) effect on grain
yield. Sequential path analysis revealed that the number of panicles
followed by the number of fertile spikelets and 100-grain weight
were the first-order factors which had positive direct effects on grain
yield. Whereas, other factors analyzed had indirect effects
influencing grain yield. This study also indicated that no significant
relationship was found between the aroma level and any of the
factors analyzed.
Abstract: Application of neural networks in execution of
programmed pulse width modulation (PPWM) of a voltage source
inverter (VSI) is studied in this paper. Using the proposed method it is
possible to cancel out the desired harmonics in output of VSI in
addition to control the magnitude of fundamental harmonic,
contineously. By checking the non-trained values and a performance
index, the most appropriate neural network is proposed. It is shown
that neural networks may solve the custom difficulties of practical
utilization of PPWM such as large size of memory, complex digital
circuits and controlling the magnitude of output voltage in a discrete
manner.
Abstract: A major challenge in biomaterials research is the
regulation of protein adsorption which is a key factor for controlling
the subsequent cell adhesion at implant surfaces. The aim of the
present study was to control the adsorption of fibronectin (FN) and
the attachment of MG-63 osteoblasts with an electronic
nanostructure. Shallow doping line lattices with a period of 260 nm
were produced for this purpose by implantation of phosphorous in
silicon wafers. Protein coverage was determined after incubating the
substrate with FN by means of an immunostaining procedure and the
measurement of the fluorescence intensity with a TECAN analyzer.
We observed an increased amount of adsorbed FN on the
nanostructure compared to control substrates. MG-63 osteoblasts
were cultivated for 24h on FN-incubated substrates and their
morphology was assessed by SEM. Preferred orientation and
elongation of the cells in direction of the doping lattice lines was
observed on FN-coated nanostructures.
Abstract: Most fingerprint recognition techniques are based on minutiae matching and have been well studied. However, this technology still suffers from problems associated with the handling of poor quality impressions. One problem besetting fingerprint matching is distortion. Distortion changes both geometric position and orientation, and leads to difficulties in establishing a match among multiple impressions acquired from the same finger tip. Marking all the minutiae accurately as well as rejecting false minutiae is another issue still under research. Our work has combined many methods to build a minutia extractor and a minutia matcher. The combination of multiple methods comes from a wide investigation into research papers. Also some novel changes like segmentation using Morphological operations, improved thinning, false minutiae removal methods, minutia marking with special considering the triple branch counting, minutia unification by decomposing a branch into three terminations, and matching in the unified x-y coordinate system after a two-step transformation are used in the work.
Abstract: A feature weighting and selection method is proposed
which uses the structure of a weightless neuron and exploits the
principles that govern the operation of Genetic Algorithms and
Evolution. Features are coded onto chromosomes in a novel way
which allows weighting information regarding the features to be
directly inferred from the gene values. The proposed method is
significant in that it addresses several problems concerned with
algorithms for feature selection and weighting as well as providing
significant advantages such as speed, simplicity and suitability for
real-time systems.
Abstract: Constant upgrading of Enterprise Resource Planning
(ERP) systems is necessary, but can cause new defects. This paper
attempts to model the likelihood of defects after completed upgrades
with Weibull defect probability density function (PDF). A case study
is presented analyzing data of recorded defects obtained for one ERP
subsystem. The trends are observed for the value of the parameters
relevant to the proposed statistical Weibull distribution for a given
one year period. As a result, the ability to predict the appearance of
defects after the next upgrade is described.
Abstract: The paper attempts to contribute to the largely
neglected social and anthropological discussion of technology development on the one hand, and to redirecting the emphasis in
anthropology from primitive and exotic societies to problems of high
relevance in contemporary era and how technology is used in
everyday life. It draws upon multidimensional models of intelligence
and ideal type formation. It is argued that the predominance of
computational and cognitive cosmovisions have led to technology alienation. Injection of communicative competence in artificially
intelligent systems and identity technologies in the coming
information society are analyzed
Abstract: The present work is a numerical simulation of
nanofluids flow in a double pipe heat exchanger provided with
porous baffles. The hot nanofluid flows in the inner cylinder, whereas
the cold nanofluid circulates in the annular gap. The Darcy-
Brinkman-Forchheimer model is adopted to describe the flow in the
porous regions, and the governing equations with the appropriate
boundary conditions are solved by the finite volume method. The
results reveal that the addition of metallic nanoparticles enhances the
rate of heat transfer in comparison to conventional fluids but this
augmentation is accompanied by an increase in pressure drop. The
highest heat exchanger performances are obtained when
nanoparticles are added only to the cold fluid.
Abstract: The aim of this study was to investigate the influence
of reaction temperature and wheat straw moisture content on the
pyrolysis product yields, in the temperature range of 475-575 °C.
Samples of straw with moisture contents from 1.5 wt % to 15.0 wt %
were fed to a bench scale Pyrolysis Centrifuge Reactor (PCR). The
experimental results show that the changes in straw moisture content
have no significant effect on the distribution of pyrolysis product
yields. The maximum bio-oil yields approximately 60 (wt %, on dry
ash free feedstock basis) was observed around 525 °C - 550 °C for all
straw moisture levels. The water content in the wet straw bio-oil was
the highest. The heating value of bio-oil and solid char were
measured and the percentages of its energy distribution were
calculated. The energy distributions of bio-oil, char and gas were 56-
69 % 24-33 %, and 2-19 %, respectively.
Abstract: One of the most important problems in production planning of flexible manufacturing system (FMS) is machine tool selection and operation allocation problem that directly influences the production costs and times .In this paper minimizing machining cost, set-up cost and material handling cost as a multi-objective problem in flexible manufacturing systems environment are considered. We present a 0-1 integer linear programming model for the multiobjective machine tool selection and operation allocation problem and due to the large scale nature of the problem, solving the problem to obtain optimal solution in a reasonable time is infeasible, Paretoant colony optimization (P-ACO) approach for solving the multiobjective problem in reasonable time is developed. Experimental results indicate effectiveness of the proposed algorithm for solving the problem.
Abstract: A shaft-type activated sludge reactor has been
developed in order to study the feasibility of high-rate wastewater
treatment. The reactor having volume of about 14.5 L was operated
with the acclimated mixed activated sludge under batch and
continuous mode using a synthetic wastewater as feed. The batch
study was performed with varying chemical oxygen demand (COD)
concentrations of 1000–3500 mg·L-1 for a batch period up to 9 h. The
kinetic coefficients: Ks, k, Y and kd were obtained as 2040.2 mg·L-1
and 0.105 h-1, 0.878 and 0.0025 h-1 respectively from Monod-s
approach. The continuous study showed a stable and steady state
operation for a hydraulic retention time (HRT) of 8 h and influent
COD of about 1000 mg·L-1. A maximum COD removal efficiency of
about 80% was attained at a COD loading rate and food-tomicroorganism
(F/M) ratio (COD basis) of 3.42 kg·m-3d-1 and 1.0
kg·kg-1d-1 respectively under a HRT of 8 h. The reactor was also
found to handle COD loading rate and F/M ratio of 10.8 kg·m-3d-1
and 2.20 kg·kg-1d-1 respectively showing a COD removal efficiency
of about 46%.
Abstract: Buildings are one of the valuable assets to provide
people with shelters for work, leisure and rest. After years of
attacks by weather, buildings will deteriorate which need proper
maintenance in order to fulfill the requirements and satisfaction of
the users. Poorly managed buildings not just give a negative image
to the city itself, but also pose potential risk hazards to the health
and safety of the general public. As a result, the management of
maintenance projects has played an important role in cities like
Hong Kong where the problem of urban decay has drawn much
attention. However, most research has focused on managing new
construction, and little research effort has been put on maintenance
projects. Given the short duration and more diversified nature of
work, repair and maintenance works are found to be more difficult
to monitor and regulate when compared with new works. Project
participants may face with problems in running maintenance
projects which should be investigated so that proper strategies can
be established. This paper aims to provide a thorough analysis on
the problems of running maintenance projects. A review of
literature on the characteristics of building maintenance projects
was firstly conducted, which forms a solid basis for the empirical
study. Results on the problems and difficulties of running
maintenance projects from the viewpoints of industry practitioners
will also be delivered with a view to formulating effective
strategies for managing maintenance projects successfully.
Abstract: Surgical site infections (SSIs) are the most common
nosocomial infection in surgical patients resulting in significant
increases in postoperative morbidity and mortality. The commonly
causative bacteria developed resistance to virtually all antibiotics
available. The aim of this study was to isolation and identification the
most common bacteria that cause SSIs in Medical Research Institute,
and to compare their sensitivity to selected group of antibiotics and
natural products (garlic, oregano, olive, and Nigella sativa oils). The
isolated pathogens collected from infected surgical wounds were
identified, and their sensitivities to the antibiotics commonly
available for clinical use, and also to the different concentrations of
the used natural products were investigated. The results indicate to
the potential therapeutic effect of the tested natural products in
treatment of surgical wound infections.
Abstract: In this project cadmium ions were adsorbed from
aqueous solutions onto either date pits; a cheap agricultural and nontoxic
material, or chemically activated carbon prepared from date pits
using phosphoric acid. A series of experiments were conducted in a
batch adsorption technique to assess the feasibility of using the
prepared adsorbents. The effects of the process variables such as
initial cadmium ions concentration, contact time, solution pH and
adsorbent dose on the adsorption capacity of both adsorbents were
studied. The experimental data were tested using different isotherm
models such as Langmuir, Freundlich, Tempkin and Dubinin-
Radushkevich. The results showed that although the equilibrium data
could be described by all models used, Langmuir model gave slightly
better results when using activated carbon while Freundlich model,
gave better results with date pits.
Abstract: Tip vortex cavitation is one of well known patterns of
cavitation phenomenon which occurs in axial pumps. This pattern of
cavitation occurs due to pressure difference between the pressure and
suction sides of blades of an axial pump. Since the pressure in the
pressure side of the blade is higher than the pressure in its suction
side, thus a very small portion of liquid flow flows back from
pressure side to the suction side. This fact is cause of tip vortex
cavitation and gap cavitation that may occur in axial pumps. In this
paper the results of our experimental investigation about movement
of tip vortex cavitation along blade edge due to reduction of pump
flow rate in an axial pump is reported. Results show that reduction of
pump flow rate in conjunction with increasing of outlet pressure
causes movement of tip vortex cavitation along blade edge towards
the blade tip. Results also show that by approaching tip vortex
cavitation to the blade tip, vortex tip pattern of cavitation replaces
with a cavitation phenomenon on the blade tip. Furthermore by
further reduction of pump flow rate and increasing of outlet pressure,
an unstable cavitation phenomenon occurs between each blade
leading edge and the next blade trailing edge.
Abstract: Contractor selection in Saudi Arabia is very important due to the large construction boom and the contractor role to get over construction risks. The need for investigating contractor selection is due to the following reasons; large number of defaulted or failed projects (18%), large number of disputes attributed to contractor during the project execution stage (almost twofold), the extension of the General Agreement on Tariffs and Trade (GATT) into construction industry, and finally the few number of researches. The selection strategy is not perfect and considered as the reason behind irresponsible contractors. As a response, this research was conducted to review the contractor selection strategies as an integral part of a long advanced research to develop a good selection model. Many techniques can be used to form a selection strategy; multi criteria for optimizing decision, prequalification to discover contractor-s responsibility, bidding process for competition, third party guarantee to enhance the selection, and fuzzy techniques for ambiguities and incomplete information.
Abstract: Commercially available lipases (Candida antarctica lipase B, Novozyme 435, Thermomyces lanuginosus lipase, and Lipozyme TL IM), as well as sol-gel immobilized lipases, have been screened for their ability to acylate regioselectively xylitol, sorbitol, and mannitol with a phenolic ester in a binary mixture of t-butanol and dimethylsulfoxide. HPLC and MALDI-TOF MS analysis revealed the exclusive formation of monoesters for all studied sugar alcohols. The lipases immobilized by the sol-gel entrapment method proved to be efficient catalysts, leading to high conversions (up to 60%) in the investigated acylation reactions. From a sequence of silane precursors with different nonhydrolyzable groups in their structure, the presence of octyl and i-butyl group was most beneficial for the catalytic activity of sol-gel entrapped lipases in the studied process.
Abstract: This paper describes a new method for affine parameter
estimation between image sequences. Usually, the parameter
estimation techniques can be done by least squares in a quadratic
way. However, this technique can be sensitive to the presence
of outliers. Therefore, parameter estimation techniques for various
image processing applications are robust enough to withstand the
influence of outliers. Progressively, some robust estimation functions
demanding non-quadratic and perhaps non-convex potentials adopted
from statistics literature have been used for solving these. Addressing
the optimization of the error function in a factual framework for
finding a global optimal solution, the minimization can begin with
the convex estimator at the coarser level and gradually introduce nonconvexity
i.e., from soft to hard redescending non-convex estimators
when the iteration reaches finer level of multiresolution pyramid.
Comparison has been made to find the performance of the results
of proposed method with the results found individually using two
different estimators.
Abstract: In H.264/AVC video encoding, rate-distortion
optimization for mode selection plays a significant role to achieve
outstanding performance in compression efficiency and video quality.
However, this mode selection process also makes the encoding
process extremely complex, especially in the computation of the ratedistortion
cost function, which includes the computations of the sum
of squared difference (SSD) between the original and reconstructed
image blocks and context-based entropy coding of the block. In this
paper, a transform-domain rate-distortion optimization accelerator
based on fast SSD (FSSD) and VLC-based rate estimation algorithm
is proposed. This algorithm could significantly simplify the hardware
architecture for the rate-distortion cost computation with only
ignorable performance degradation. An efficient hardware structure
for implementing the proposed transform-domain rate-distortion
optimization accelerator is also proposed. Simulation results
demonstrated that the proposed algorithm reduces about 47% of total
encoding time with negligible degradation of coding performance.
The proposed method can be easily applied to many mobile video
application areas such as a digital camera and a DMB (Digital
Multimedia Broadcasting) phone.