Abstract: The most severe damage of the turbine rotor is its
distortion. The rotor straightening process must lead, at the first
stage, to removal of the stresses from the material by annealing and
next, to straightening of the plastic distortion without leaving any
stress by hot spotting. The straightening method does not produce
stress accumulations and the heating technique, developed
specifically for solid forged rotors and disks, enables to avoid local
overheating and structural changes in the material. This process also
does not leave stresses in the shaft material. An experimental study
of hot spotting is carried out on a large turbine rotor and some of the
most important effective parameters that must be considered on
annealing and hot spotting processes are investigated in this paper.
Abstract: The research object was apple-black currant
marmalade candies. Experiments were carried out at the Faculty of
Food Technology of the Latvia University of Agriculture. An active
packaging in combination with modified atmosphere (MAP, CO2
100%) was examined and compared with traditional packaging in air
ambiance. Polymer Multibarrier 60 and paper bags were used.
Influence of iron based oxygen absorber in sachets of 500 cc
obtained from Mitsubishi Gas Chemical Europe Ageless® was tested
on the quality during the shelf of marmalade. Samples of 80±5 g
were packaged in polymer pouches (110 mm x 110 mm),
hermetically sealed by MULTIVAC C300 vacuum chamber machine,
and stored in room temperature +20.0±1.0 °C. The physiochemical
properties – weight losses, moisture content, hardness, aw, pH, colour,
changes of atmosphere content (CO2 and O2) in headspace of packs,
and microbial conditions were analysed before packaging and in the
1st, 3rd , 5th, 8th, 11th and 15th weeks of storage.
Abstract: Content-based music retrieval generally involves analyzing, searching and retrieving music based on low or high level features of a song which normally used to represent artists, songs or music genre. Identifying them would normally involve feature extraction and classification tasks. Theoretically the greater features analyzed, the better the classification accuracy can be achieved but with longer execution time. Technique to select significant features is important as it will reduce dimensions of feature used in classification and contributes to the accuracy. Artificial Immune System (AIS) approach will be investigated and applied in the classification task. Bio-inspired audio content-based retrieval framework (B-ACRF) is proposed at the end of this paper where it embraces issues that need further consideration in music retrieval performances.
Abstract: The paper provides a discussion of the most relevant
aspects of yield curve modeling. Two classes of models are
considered: stochastic and parsimonious function based, through the
approaches developed by Vasicek (1977) and Nelson and Siegel
(1987). Yield curve estimates for Croatia are presented and their
dynamics analyzed and finally, a comparative analysis of models is
conducted.
Abstract: One part of the total employee’s reward is apart from basic wages or salary, employee’s benefits and intangible remuneration also so called contingent (variable) pay. Contingent pay is connected to performance, contribution, cap competency or skills of individual employees, and to team’s or company-wide performance or to combination of few of the mentioned possibilities. Sometimes among the contingent pay is also incorporated the remuneration based on length of employment, when the financial reward is not connected to performance or skills, but to length of continuous employment either on one working position or in one level of remuneration scale. Main aim of this article is to define, based on available information, contingent pay, describe individual forms, its advantages and disadvantages and possibilities to utilization in practice; but also bring information not only about its extent and level of utilization of contingent pay by companies in one of the Czech Republic’s regions, but also mention their practical experience with this type of remuneration.
Abstract: This paper examines the interplay of policy options
and cost-effective technology in providing sustainable distance
education. A case study has been conducted among the learners and
teachers. The emergence of learning technologies through CD,
internet, and mobile is increasingly adopted by distance institutes for
quick delivery and cost-effective factors. Their sustainability is
conditioned by the structure of learners and well as the teaching
community. The structure of learners in terms of rural and urban
background revealed similarity in adoption and utilization of mobile
learning. In other words, the technology transcended the rural-urban
dichotomy. The teaching community was divided into two groups on
policy issues. This study revealed both cost-effective as well as
sustainability impacts on different learners groups divided by rural
and urban location.
Abstract: The objective of this research is to study the technical
and economic performance of wind/diesel/battery (W/D/B) system
supplying a remote small gathering of six families using HOMER
software package. The electrical energy is to cater for the basic needs
for which the daily load pattern is estimated. Net Present Cost (NPC)
and Cost of Energy (COE) are used as economic criteria, while the measure of performance is % of power shortage. Technical and
economic parameters are defined to estimate the feasibility of the
system under study. Optimum system configurations are estimated for two sites. Using HOMER software, the simulation results showed that W/D/B systems are economical for the assumed community sites
as the price of generated electricity is about 0.308 $/kWh, without
taking external benefits into considerations. W/D/B systems are more
economical than W/B or diesel alone systems, as the COE is 0.86 $/kWh for W/B and 0.357 $/kWh for diesel alone.
Abstract: The paper presents the brief information on particular results of experimental study focused to the problems of behavior of structural plated components made of fiber-cement-based materials and used in building constructions, exposed to atmospheric physical effects given by the weather changes in the summer period. Weather changes represented namely by temperature and rain cause also the changes of the temperature and moisture of the investigated structural components. This can affect their static behavior that means stresses and deformations, which have been monitored as the main outputs of tests performed. Experimental verification is based on the simulation of the influence of temperature and rain using the defined procedure of warming and water sprinkling with respect to the corresponding weather conditions during summer period in the South Moravian region at the Czech Republic, for which the application of these structural components is mainly planned. Two types of components have been tested: (i) glass-fiber-concrete panels used for building façades and (ii) fiber-cement slabs used mainly for claddings, but also as a part of floor structures or lost shuttering, and so on.
Abstract: Static synchronous compensator (STATCOM) is a shunt connected voltage source converter (VSC), which can affect rapid control of reactive flow in the transmission line by controlling the generated a.c. voltage. The main aim of the paper is to design a power system installed with a Static synchronous compensator (STATCOM) and demonstrates the application of the linearised Phillips-heffron model in analyzing the damping effect of the STATCOM to improve power system oscillation stability. The proposed PI controller is designed to coordinate two control inputs: Voltage of the injection bus and capacitor voltage of the STATCOM, to improve the Dynamic stability of a SMIB system .The power oscillations damping (POD) control and power system stabilizer (PSS) and their coordinated action with proposed controllers are tested. The simulation result shows that the proposed damping controllers provide satisfactory performance in terms of improvements of dynamic stability of the system.
Abstract: The case study deals with the semi-quantitative risk
assessment of water resource earmarked for the emergency supply
of population with drinking water. The risk analysis has been based
on previously identified hazards/sensitivities of the elements
of hydrogeological structure and technological equipment of ground
water resource as well as on the assessment of the levels of hazard,
sensitivity and criticality of individual resource elements in the form
of point indexes. The following potential sources of hazard have
been considered: natural disasters caused by atmospheric and
geological changes, technological hazards, and environmental
burdens. The risk analysis has proved that the assessed risks are
acceptable and the water resource may be integrated into a crisis plan
of a given region.
Abstract: Worldwide many electrical equipment insulation
failures have been reported caused by switching operations, while
those equipments had previously passed all the standard tests and
complied with all quality requirements. The problem is mostly
associated with high-frequency overvoltages generated during
opening or closing of a switching device. The transients generated
during switching operations in a Gas Insulated Substation (GIS) are
associated with high frequency components in the order of few tens
of MHz.
The frequency spectrum of the VFTO generated in the 220/66 kV
Wadi-Hoff GIS is analyzed using Fast Fourier Transform technique.
The main frequency with high voltage amplitude due to the operation
of disconnector (DS5) is 5 to 10 MHz, with the highest amplitude at 9
MHz. The main frequency with high voltage amplitude due to the
operation of circuit breaker (CB5) is 1 to 25 MHz, with the highest
amplitude at 2 MHz.
Mitigating techniques damped the oscillating frequencies
effectively. The using of cable terminal reduced the frequency
oscillation effectively than that of OHTL terminal. The using of a
shunt capacitance results in vanishing the high frequency
components. Ferrite rings reduces the high frequency components
effectively especially in the range 2 to 7 MHz. The using of RC and
RL filters results in vanishing the high frequency components.
Abstract: Noise has adverse effect on human health and
comfort. Noise not only cause hearing impairment, but it also acts as
a causal factor for stress and raising systolic pressure. Additionally it
can be a causal factor in work accidents, both by marking hazards
and warning signals and by impeding concentration. Industry
workers also suffer psychological and physical stress as well as
hearing loss due to industrial noise. This paper proposes an approach
to enable engineers to point out quantitatively the noisiest source for
modification, while multiple machines are operating simultaneously.
The model with the point source and spherical radiation in a free field
was adopted to formulate the problem. The procedure works very
well in ideal cases (point source and free field). However, most of the
industrial noise problems are complicated by the fact that the noise is
confined in a room. Reflections from the walls, floor, ceiling, and
equipment in a room create a reverberant sound field that alters the
sound wave characteristics from those for the free field. So the model
was validated for relatively low absorption room at NIT Kurukshetra
Central Workshop. The results of validation pointed out that the
estimated sound power of noise sources under simultaneous
conditions were on lower side, within the error limits 3.56 - 6.35 %.
Thus suggesting the use of this methodology for practical
implementation in industry. To demonstrate the application of the
above analytical procedure for estimating the sound power of noise
sources under simultaneous operating conditions, a manufacturing
facility (Railway Workshop at Yamunanagar, India) having five
sound sources (machines) on its workshop floor is considered in this
study. The findings of the case study had identified the two most
effective candidates (noise sources) for noise control in the Railway
Workshop Yamunanagar, India. The study suggests that the
modification in the design and/or replacement of these two identified
noisiest sources (machine) would be necessary so as to achieve an
effective reduction in noise levels. Further, the estimated data allows
engineers to better understand the noise situations of the workplace
and to revise the map when changes occur in noise level due to a
workplace re-layout.
Abstract: In the paper the study of synthetic transmit aperture
method applying the Golay coded transmission for medical
ultrasound imaging is presented. Longer coded excitation allows to
increase the total energy of the transmitted signal without increasing
the peak pressure. Moreover signal-to-noise ratio and penetration
depth are improved while maintaining high ultrasound image
resolution. In the work the 128-element linear transducer array with
0.3 mm inter-element spacing excited by one cycle and the 8 and 16-
bit Golay coded sequences at nominal frequency 4 MHz was used. To
generate a spherical wave covering the full image region a single
element transmission aperture was used and all the elements received
the echo signals. The comparison of 2D ultrasound images of the
tissue mimicking phantom and in vitro measurements of the beef liver
is presented to illustrate the benefits of the coded transmission. The
results were obtained using the synthetic aperture algorithm with
transmit and receive signals correction based on a single element
directivity function.
Abstract: The use of a Bayesian Hierarchical Model (BHM) to interpret breath measurements obtained during a 13C Octanoic Breath Test (13COBT) is demonstrated. The statistical analysis was implemented using WinBUGS, a commercially available computer package for Bayesian inference. A hierarchical setting was adopted where poorly defined parameters associated with a delayed Gastric Emptying (GE) were able to "borrow" strength from global distributions. This is proved to be a sufficient tool to correct model's failures and data inconsistencies apparent in conventional analyses employing a Non-linear least squares technique (NLS). Direct comparison of two parameters describing gastric emptying ng ( tlag -lag phase, t1/ 2 -half emptying time) revealed a strong correlation between the two methods. Despite our large dataset ( n = 164 ), Bayesian modeling was fast and provided a successful fitting for all subjects. On the contrary, NLS failed to return acceptable estimates in cases where GE was delayed.
Abstract: Panoramic view generation has always offered
novel and distinct challenges in the field of image processing.
Panoramic view generation is nothing but construction of bigger
view mosaic image from set of partial images of the desired view.
The paper presents a solution to one of the problems of image
seascape formation where some of the partial images are color and
others are grayscale. The simplest solution could be to convert all
image parts into grayscale images and fusing them to get grayscale
image panorama. But in the multihued world, obtaining the colored
seascape will always be preferred. This could be achieved by picking
colors from the color parts and squirting them in grayscale parts of
the seascape. So firstly the grayscale image parts should be colored
with help of color image parts and then these parts should be fused to
construct the seascape image.
The problem of coloring grayscale images has no exact solution.
In the proposed technique of panoramic view generation, the job of
transferring color traits from reference color image to grayscale
image is done by palette based method. In this technique, the color
palette is prepared using pixel windows of some degrees taken from
color image parts. Then the grayscale image part is divided into pixel
windows with same degrees. For every window of grayscale image
part the palette is searched and equivalent color values are found,
which could be used to color grayscale window. For palette
preparation we have used RGB color space and Kekre-s LUV color
space. Kekre-s LUV color space gives better quality of coloring. The
searching time through color palette is improved over the exhaustive
search using Kekre-s fast search technique.
After coloring the grayscale image pieces the next job is fusion of
all these pieces to obtain panoramic view. For similarity estimation
between partial images correlation coefficient is used.
Abstract: Leo Breimans Random Forests (RF) is a recent
development in tree based classifiers and quickly proven to be one of
the most important algorithms in the machine learning literature. It
has shown robust and improved results of classifications on standard
data sets. Ensemble learning algorithms such as AdaBoost and
Bagging have been in active research and shown improvements in
classification results for several benchmarking data sets with mainly
decision trees as their base classifiers. In this paper we experiment to
apply these Meta learning techniques to the random forests. We
experiment the working of the ensembles of random forests on the
standard data sets available in UCI data sets. We compare the
original random forest algorithm with their ensemble counterparts
and discuss the results.
Abstract: Stress Concentration Factors are significant in
machine design as it gives rise to localized stress when any change in
the design of surface or abrupt change in the cross section occurs.
Almost all machine components and structural members contain
some form of geometrical or microstructural discontinuities. These
discontinuities are very dangerous and lead to failure. So, it is very
much essential to analyze the stress concentration factors for critical
applications like Turbine Rotors. In this paper Finite Element
Analysis (FEA) with extremely fine mesh in the vicinity of the
blades of Steam Turbine Rotor is applied to determine stress
concentration factors. A model of Steam Turbine Rotor is shown in
Fig. 1.
Abstract: The most reliable and accurate description of the actual behavior of a software system is its source code. However, not all questions about the system can be answered directly by resorting to this repository of information. What the reverse engineering methodology aims at is the extraction of abstract, goal-oriented “views" of the system, able to summarize relevant properties of the computation performed by the program. While concentrating on reverse engineering we had modeled the C++ files by designing the translator.
Abstract: The aim of this paper is to present a comparative
study on two different methods for the evaluation of the equilibrium
point of a ship, core issue for designing an On Board Stability System
(OBSS) module that, starting from geometry information of a ship
hull, described by a discrete model in a standard format, and the
distribution of all weights onboard calculates the ship floating
conditions (in draught, heel and trim).
Abstract: System identification is the process of creating
models of dynamic process from input- output signals. The aim of
system identification can be identified as “ to find a model with
adjustable parameters and then to adjust them so that the predicted
output matches the measured output". This paper presents a method
of modeling and simulating with system identification to achieve the
maximum fitness for transformation function. First by using
optimized KLM equivalent circuit for PVDF piezoelectric transducer
and assuming different inputs including: sinuside, step and sum of
sinusides, get the outputs, then by using system identification
toolbox in MATLAB, we estimate the transformation function from
inputs and outputs resulted in last program. Then compare the fitness
of transformation function resulted from using ARX,OE(Output-
Error) and BJ(Box-Jenkins) models in system identification toolbox
and primary transformation function form KLM equivalent circuit.