Abstract: In this paper, we have examined the effect of process
parameter variation on the electrical characteristics of an LDMOS
device. The rate of change in the electrical parameters such as cut off
frequency, breakdown voltage and drain saturation current as a
function of the process parameters is investigated
Abstract: Time delay in bilateral teleoperation system was
introduced as a sufficient reason to make the system unstable or
certainly degrade the system performance. In this paper, simulations
and experimental results of implementing p-like control scheme,
under different ranges of variable time delay, will be presented to
verify a certain criteria, which guarantee the system stability and
position tracking. The system consists of two Phantom premium 1.5A
devices. One of them acts as a master and the other acts as a slave.
The study includes deriving the Phantom kinematic and dynamic
model, establishing the link between the two Phantoms over
Simulink in Matlab, and verifying the stability criteria with
simulations and real experiments.
Abstract: Today, numerical simulation is a powerful tool to
solve various hydraulic engineering problems. The aim of this
research is numerical solutions of shallow water equations using
finite volume method for Simulations of dam break over wet and dry
bed. In order to solve Riemann problem, Roe-s approximate solver is
used. To evaluate numerical model, simulation was done in 1D and
2D states. In 1D state, two dam break test over dry bed (with and
without friction) were studied. The results showed that Structural
failure around the dam and damage to the downstream constructions
in bed without friction is more than friction bed. In 2D state, two
tests for wet and dry beds were done. Generally in wet bed case,
waves are propagated to canal sides but in dry bed it is not
significant. Therefore, damage to the storage facilities and
agricultural lands in wet bed case is more than in dry bed.
Abstract: The main purpose of this research was to analyze Socio-Cultural obstacles of disseminating of nanotechnology in Iran's agricultural section. One hundred twenty eight out of a total of 190 researchers with different levels of expertise in and familiarity with nanotechnology were randomly selected and questionnaires completed by them. Face validity have been done by expert's suggestion and correction, reliability by using Cronbakh-Alpha formula. The results of a factor analysis showed variation for different factors. For cultural factors 19/475 percent, for management 13/139 percent, information factor 11/277 percent, production factor 9/703 percent, social factor 9/267 percent, and for attitude factor it became 8/947 percent. Also results indicated that socio-cultural factors were the most important obstacle for nanotechnology dissemination in agricultural section in Iran.
Abstract: Brain ArterioVenous Malformation (BAVM) is an abnormal tangle of brain blood vessels where arteries shunt directly into veins with no intervening capillary bed which causes high pressure and hemorrhage risk. The success of treatment by embolization in interventional neuroradiology is highly dependent on the accuracy of the vessels visualization. In this paper the performance of clustering techniques on vessel segmentation from 3- D rotational angiography (3DRA) images is investigated and a new technique of segmentation is proposed. This method consists in: preprocessing step of image enhancement, then K-Means (KM), Fuzzy C-Means (FCM) and Expectation Maximization (EM) clustering are used to separate vessel pixels from background and artery pixels from vein pixels when possible. A post processing step of removing false-alarm components is applied before constructing a three-dimensional volume of the vessels. The proposed method was tested on six datasets along with a medical assessment of an expert. Obtained results showed encouraging segmentations.
Abstract: In this research saffron samples were prepared from
farms and sampling was done in four states contain : sampling from
fresh saffron of petal with forceps , sampling from fresh saffron of
petal by hands, sampling from dried sample by warm air in shadow,
sampling from dried sample which dried by dryer. Samples collected
and kept in sterile tubes and containers and carried to laboratory and
maintained until experiment. Microbial experiments were performed
to determine microbial load such as total count, Staphylococcus
aureus, coli form, E.coli, mold and yeast. Results showed that in
picking and drying stages the contamination amount increases in
saffron samples. There was a significant difference between the
microbial load of picked up saffron by forceps and by hands, and
also between dried saffron by warm air in shadow and by dryer.
Abstract: This paper describes a new supervised fusion (hybrid)
electrocardiogram (ECG) classification solution consisting of a new
QRS complex geometrical feature extraction as well as a new version
of the learning vector quantization (LVQ) classification algorithm
aimed for overcoming the stability-plasticity dilemma. Toward this
objective, after detection and delineation of the major events of ECG
signal via an appropriate algorithm, each QRS region and also its
corresponding discrete wavelet transform (DWT) are supposed as
virtual images and each of them is divided into eight polar sectors.
Then, the curve length of each excerpted segment is calculated
and is used as the element of the feature space. To increase the
robustness of the proposed classification algorithm versus noise,
artifacts and arrhythmic outliers, a fusion structure consisting of
five different classifiers namely as Support Vector Machine (SVM),
Modified Learning Vector Quantization (MLVQ) and three Multi
Layer Perceptron-Back Propagation (MLP–BP) neural networks with
different topologies were designed and implemented. The new proposed
algorithm was applied to all 48 MIT–BIH Arrhythmia Database
records (within–record analysis) and the discrimination power of the
classifier in isolation of different beat types of each record was
assessed and as the result, the average accuracy value Acc=98.51%
was obtained. Also, the proposed method was applied to 6 number
of arrhythmias (Normal, LBBB, RBBB, PVC, APB, PB) belonging
to 20 different records of the aforementioned database (between–
record analysis) and the average value of Acc=95.6% was achieved.
To evaluate performance quality of the new proposed hybrid learning
machine, the obtained results were compared with similar peer–
reviewed studies in this area.
Abstract: Although services play a crucial role in economy,
service did not gain as much importance as productivity management
in manufacturing. This paper presents key findings from literature
and practice. Based on an initial definition of complex services, seven
productivity concepts are briefly presented and assessed by relevant,
complex service specific criteria. Following the findings a complex
service productivity model is proposed. The novel model comprises
of all specific dimensions of service provision from both, the
provider-s as well as costumer-s perspective. A clear assignment of
identified value drivers and relationships between them is presented.
In order to verify the conceptual service productivity model a case
study from a project engineering department of a chemical plant
development and construction company is presented.
Abstract: In this paper, we present a simple circuit for
Manchester decoding and without using any complicated or
programmable devices. This circuit can decode 90kbps of transmitted
encoded data; however, greater than this transmission rate can be
decoded if high speed devices were used. We also present a new
method for extracting the embedded clock from Manchester data in
order to use it for serial-to-parallel conversion. All of our
experimental measurements have been done using simulation.
Abstract: Fermented cassava flours (lafun) sold in Ogun and Oyo
States of Nigeria were collected from 10 markets for a period of two
months and analysed to determine their safety status. The presence of
trace metals was due to high vehicular movement around the drying
sites and markets. Cyanide and moisture contents of samples were
also determined to assess the adequacy of fermentation and drying.
The result showed that sample OWO was found to have the highest
amount of 16.02±0.12mg/kg cyanide while the lowest was found in
sample OJO with 10.51±0.10mg/kg. The results also indicated that
sample TVE had the highest moisture content of 18.50±0.20% while
sample OWO had the lowest amount of 12.46±0.47%. Copper and
lead levels were found to be highest in TVE with values 28.10mg/kg
and 1.1mg/kg respectively, while sample BTS had the lowest values
of 20.6mg/kg and 0.05mg/kg respectively. High value of cyanide
indicated inadequate fermentation.
Abstract: The purpose of this study is to present a non invasive
method for the marginal adaptation evaluation in class V composite
restorations. Standardized class V cavities, prepared in human
extracted teeth, were filled with Premise (Kerr) composite. The
specimens were thermo cycled. The interfaces were examined by
Optical Coherence Tomography method (OCT) combined with the
confocal microscopy and fluorescence. The optical configuration
uses two single mode directional couplers with a superluminiscent
diode as the source at 1300 nm. The scanning procedure is similar to
that used in any confocal microscope, where the fast scanning is enface
(line rate) and the depth scanning is much slower (at the frame
rate). Gaps at the interfaces as well as inside the composite resin
materials were identified. OCT has numerous advantages which
justify its use in vivo as well as in vitro in comparison with
conventional techniques.
Abstract: The study of human hand morphology reveals that developing an artificial hand with the capabilities of human hand is an extremely challenging task. This paper presents the development of a robotic prosthetic hand focusing on the improvement of a tendon driven mechanism towards a biomimetic prosthetic hand. The design of this prosthesis hand is geared towards achieving high level of dexterity and anthropomorphism by means of a new hybrid mechanism that integrates a miniature motor driven actuation mechanism, a Shape Memory Alloy actuated mechanism and a passive mechanical linkage. The synergy of these actuators enables the flexion-extension movement at each of the finger joints within a limited size, shape and weight constraints. Tactile sensors are integrated on the finger tips and the finger phalanges area. This prosthesis hand is developed with an exact size ratio that mimics a biological hand. Its behavior resembles the human counterpart in terms of working envelope, speed and torque, and thus resembles both the key physical features and the grasping functionality of an adult hand.
Abstract: Time varying network induced delays in networked
control systems (NCS) are known for degrading control system-s
quality of performance (QoP) and causing stability problems. In
literature, a control method employing modeling of communication
delays as probability distribution, proves to be a better method. This
paper focuses on modeling of network induced delays as probability
distribution.
CAN and MIL-STD-1553B are extensively used to carry periodic
control and monitoring data in networked control systems.
In literature, methods to estimate only the worst-case delays for
these networks are available. In this paper probabilistic network
delay model for CAN and MIL-STD-1553B networks are given.
A systematic method to estimate values to model parameters from
network parameters is given. A method to predict network delay in
next cycle based on the present network delay is presented. Effect of
active network redundancy and redundancy at node level on network
delay and system response-time is also analyzed.
Abstract: Independent component analysis (ICA) is a computational method for finding underlying signals or components from multivariate statistical data. The ICA method has been successfully applied in many fields, e.g. in vision research, brain imaging, geological signals and telecommunications. In this paper, we apply the ICA method to an analysis of mass spectra of oligomeric species emerged from aluminium sulphate. Mass spectra are typically complex, because they are linear combinations of spectra from different types of oligomeric species. The results show that ICA can decomposite the spectral components for useful information. This information is essential in developing coagulation phases of water treatment processes.
Abstract: This research was carried out to determine the
possible effects of low electromagnetic field (EMF) exposure to the
developing mice fetuses. Pregnant mice were exposed to EMF
exposure at 0mT (sham) and 1.2 mT for six hours per session, carried
out on gestation day 3, 6, 9, 12 and 15. Samples from the stillborn
offspring were observed for morphological defects. The heart didn-t
show progressive cellular damage, the lungs were congested and
emphysemics. The bones were in advance stage of hypertrophy.
Spectrums of morphological defects were observed over 70% of the
surviving offspring. These results indicate that even at lower
exposure to low EMF, is enough to induce morphological defects in
prenatal mice.
Abstract: The world-s largest Pre-stressed Concrete Cylinder
Pipe (PCCP) water supply project had a series of pipe failures which
occurred between 1999 and 2001. This has led the Man-Made River
Authority (MMRA), the authority in charge of the implementation
and operation of the project, to setup a rehabilitation plan for the
conveyance system while maintaining the uninterrupted flow of
water to consumers. At the same time, MMRA recognized the need
for a long term management tool that would facilitate repair and
maintenance decisions and enable taking the appropriate preventive
measures through continuous monitoring and estimation of the
remaining life of each pipe. This management tool is known as the
Pipe Risk Management System (PRMS) and now in operation at
MMRA. Both the rehabilitation plan and the PRMS require the
availability of complete and accurate pipe construction and
manufacturing data
This paper describes a systematic approach of data collection,
analysis, evaluation and correction for the construction and
manufacturing data files of phase I pipes which are the platform for
the PRMS database and any other related decision support system.
Abstract: the aim of this study was to analyze ethnopsychological content of “Aitys" as a process of creative competition in Kazakh traditional folklore by means of Transaction analysis (three types of Ego states are Parent, Adult and Child). “Aitys" is as sources of Kazakh national self-consciousness and form of oral Kazakh national creativity. Comparative psychological analysis of classical and modern “aityses" is carried out. Empirical proved that the victory in “Aitys" is provided with a position of egostate “Adult".
Abstract: Chicken fat was employed as a feedstock for
producing of biodiesel by trasesterification reaction with methanol
and alkali catalyst (KOH). In this study chicken fat biodiesel with
1.4% free fatty acid, methanol and various amount of potassium
hydroxide for 2 hour were studied. The progression of reaction and
conversion of triglycerides to methyl ester were checked by IR
spectrum method.
Abstract: A subcarrier - spectral amplitude coding optical code
division multiple access system using the Khazani-Syed code with
Complementary subtraction detection technique is proposed. The
proposed system has been analyzed by taking into account the effects
of phase-induced intensity noise, shot noise, thermal noise and intermodulation
distortion noise. The performance of the system has been
compared with the spectral amplitude coding optical code division
multiple access system using the Hadamard code and the Modified
Quadratic Congruence code. The analysis shows that the proposed
system can eliminate the multiple access interference using the
Complementary subtraction detection technique, and hence improve
the overall system performance.
Abstract: Mobile learning (m-learning) is a new method in teaching and learning process which combines technology of mobile device with learning materials. It can enhance student's engagement in learning activities and facilitate them to access the learning materials at anytime and anywhere. In Kolej Poly-Tech Mara (KPTM), this method is seen as an important effort in teaching practice and to improve student learning performance. The aim of this paper is to discuss the development of m-learning application called Mobile EEF Learning System (MEEFLS) to be implemented for Electric and Electronic Fundamentals course using Flash, XML (Extensible Markup Language) and J2ME (Java 2 micro edition). System Development Life Cycle (SDLC) was used as an application development approach. It has three modules in this application such as notes or course material, exercises and video. MEELFS development is seen as a tool or a pilot test for m-learning in KPTM.