Abstract: In this paper is shown that the probability-statistic methods application, especially at the early stage of the aviation gas turbine engine (GTE) technical condition diagnosing, when the flight information has property of the fuzzy, limitation and uncertainty is unfounded. Hence is considered the efficiency of application of new technology Soft Computing at these diagnosing stages with the using of the Fuzzy Logic and Neural Networks methods. Training with high accuracy of fuzzy multiple linear and non-linear models (fuzzy regression equations) which received on the statistical fuzzy data basis is made. Thus for GTE technical condition more adequate model making are analysed dynamics of skewness and kurtosis coefficients' changes. Researches of skewness and kurtosis coefficients values- changes show that, distributions of GTE work parameters have fuzzy character. Hence consideration of fuzzy skewness and kurtosis coefficients is expedient. Investigation of the basic characteristics changes- dynamics of GTE work parameters allows to draw conclusion on necessity of the Fuzzy Statistical Analysis at preliminary identification of the engines' technical condition. Researches of correlation coefficients values- changes shows also on their fuzzy character. Therefore for models choice the application of the Fuzzy Correlation Analysis results is offered. For checking of models adequacy is considered the Fuzzy Multiple Correlation Coefficient of Fuzzy Multiple Regression. At the information sufficiency is offered to use recurrent algorithm of aviation GTE technical condition identification (Hard Computing technology is used) on measurements of input and output parameters of the multiple linear and non-linear generalised models at presence of noise measured (the new recursive Least Squares Method (LSM)). The developed GTE condition monitoring system provides stage-bystage estimation of engine technical conditions. As application of the given technique the estimation of the new operating aviation engine temperature condition was made.
Abstract: In this paper the direct kinematic model of a multiple
applications three degrees of freedom industrial manipulator, was
developed using the homogeneous transformation matrices and the
Denavit - Hartenberg parameters, likewise the inverse kinematic
model was developed using the same method, verifying that in the
workload border the inverse kinematic presents considerable errors,
therefore a genetic algorithm was implemented to optimize the model
improving greatly the efficiency of the model.
Abstract: Response to the public health-related emergencies is analysed here for a rural university in South Africa. The structure of the designated emergency plan covers all the phases of the disaster management cycle. The plan contains elements of the vulnerability model and the technocratic model of emergency management. The response structures are vertically and horizontally integrated, while the planning contains elements of scenario-based and functional planning. The available number of medical professionals at the Rhodes University, along with the medical insurance rates, makes the staff and students potentially more medically vulnerable than the South African population. The main improvements of the emergency management are required in the tornado response and the information dissemination during health emergencies. The latter should involve the increased use of social media and e-mails, following the Taylor model of communication. Infrastructure must be improved in the telecommunication sector in the face of unpredictable electricity outages.
Abstract: This paper will focus on modeling, analysis and simulation of a 42V/14V dc/dc converter based architecture. This architecture is considered to be technically a viable solution for automotive dual-voltage power system for passenger car in the near further. An interleaved dc/dc converter system is chosen for the automotive converter topology due to its advantages regarding filter reduction, dynamic response, and power management. Presented herein, is a model based on one kilowatt interleaved six-phase buck converter designed to operate in a Discontinuous Conduction Mode (DCM). The control strategy of the converter is based on a voltagemode- controlled Pulse Width Modulation (PWM) with a Proportional-Integral-Derivative (PID). The effectiveness of the interleaved step-down converter is verified through simulation results using control-oriented simulator, MatLab/Simulink.
Abstract: The behavior of three phase five leg transformer under voltage sag is studied in this paper. This paper proposes a simple, practical model of a three phase-five leg, saturated transformer with accurate performance. Transformer saturation is produced when the voltage sag is recovered and it causes inrush current in transformer. Effects of voltage sag depth, duration and initial point on wave have been analyzed in this paper. Initial point on wave can produce maximum inrush current in five leg transformers while comparing with three leg transformers. The magnetic circuit symmetry of five leg transformer produces the more symmetrical shape of inrush current curves versus initial point on wave and sag duration than three leg transformer. The simulations show that current peak has a periodical dependence on sag duration and linear dependence on sag depth. Inrush current that is produced in three phase five leg transformer is higher than three phase three leg transformer.
Abstract: Recently, there have been considerable efforts towards the convergence between P2P and Grid computing in order to reach a solution that takes the best of both worlds by exploiting the advantages that each offers. Augmenting the peer-to-peer model to the services of the Grid promises to eliminate bottlenecks and ensure greater scalability, availability, and fault-tolerance. The Grid Information Service (GIS) directly influences quality of service for grid platforms. Most of the proposed solutions for decentralizing the GIS are based on completely flat overlays. The main contributions for this paper are: the investigation of a novel resource discovery framework for Grid implementations based on a hierarchy of structured peer-to-peer overlay networks, and introducing a discovery algorithm utilizing the proposed framework. Validation of the framework-s performance is done via simulation. Experimental results show that the proposed organization has the advantage of being scalable while providing fault-isolation, effective bandwidth utilization, and hierarchical access control. In addition, it will lead to a reliable, guaranteed sub-linear search which returns results within a bounded interval of time and with a smaller amount of generated traffic within each domain.
Abstract: A novel methodology has been used to design an
evaporator coil of a refrigerant. The methodology used is through a
complete Computer Aided Design /Computer Aided Engineering
approach, by means of a Computational Fluid Dynamic/Finite
Element Analysis model which is executed many times for the
thermal-fluid exploration of several designs' configuration by an
commercial optimizer. Hence the design is carried out automatically
by parallel computations, with an optimization package taking the
decisions rather than the design engineer. The engineer instead takes
decision regarding the physical settings and initializing of the
computational models to employ, the number and the extension of the
geometrical parameters of the coil fins and the optimization tools to
be employed. The final design of the coil geometry found to be better
than the initial design.
Abstract: Power Spectral Density (PSD) computed by taking the Fourier transform of auto-correlation functions (Wiener-Khintchine Theorem) gives better result, in case of noisy data, as compared to the Periodogram approach. However, the computational complexity of Wiener-Khintchine approach is more than that of the Periodogram approach. For the computation of short time Fourier transform (STFT), this problem becomes even more prominent where computation of PSD is required after every shift in the window under analysis. In this paper, recursive version of the Wiener-Khintchine theorem has been derived by using the sliding DFT approach meant for computation of STFT. The computational complexity of the proposed recursive Wiener-Khintchine algorithm, for a window size of N, is O(N).
Abstract: This paper provides an overview of auction theory
literature. We present a general review on literature of various
auctions and focus ourselves specifically on an English auction. We
are interested in modelling bidder-s behavior in an English auction
environment. And hence, we present an overview of the New Zealand
wool auction followed by a model that would describe a bidder-s
decision making behavior from the New Zealand wool auction. The
mathematical assumptions in an English auction environment are
demonstrated from the perspective of the New Zealand wool auction.
Abstract: This paper focuses on a novel method for semantic
searching and retrieval of information about learning materials.
Metametadata encapsulate metadata instances by using the properties
and attributes provided by ontologies rather than describing learning
objects. A novel metametadata taxonomy has been developed which
provides the basis for a semantic search engine to extract, match and
map queries to retrieve relevant results. The use of ontological views
is a foundation for viewing the pedagogical content of metadata
extracted from learning objects by using the pedagogical attributes
from the metametadata taxonomy. Using the ontological approach
and metametadata (based on the metametadata taxonomy) we present
a novel semantic searching mechanism.These three strands – the
taxonomy, the ontological views, and the search algorithm – are
incorporated into a novel architecture (OMESCOD) which has been
implemented.
Abstract: In MPEG and H.26x standards, to eliminate the
temporal redundancy we use motion estimation. Given that the
motion estimation stage is very complex in terms of computational
effort, a hardware implementation on a re-configurable circuit is
crucial for the requirements of different real time multimedia
applications. In this paper, we present hardware architecture for
motion estimation based on "Full Search Block Matching" (FSBM)
algorithm. This architecture presents minimum latency, maximum
throughput, full utilization of hardware resources such as embedded
memory blocks, and combining both pipelining and parallel
processing techniques. Our design is described in VHDL language,
verified by simulation and implemented in a Stratix II
EP2S130F1020C4 FPGA circuit. The experiment result show that the
optimum operating clock frequency of the proposed design is 89MHz
which achieves 160M pixels/sec.
Abstract: Green buildings have been commonly cited to be more
expensive than conventional buildings. However, limited research
has been conducted to clearly identify elements that contribute to this
cost differential. The construction cost of buildings can be typically
divided into “hard" costs and “soft" cost elements. Using a review
analysis of existing literature, the study identified six main elements
in green buildings that contribute to the general cost elements that are
“soft" in nature. The six elements found are insurance, developer-s
experience, design cost, certification, commissioning and energy
modeling. Out of the six elements, most literatures have highlighted
the increase in design cost for green design as compared to
conventional design due to additional architectural and engineering
costs, eco-charettes, extra design time, and the further need for a
green consultant. The study concluded that these elements of soft cost
contribute to the green premium or cost differential of green
buildings.
Abstract: In this project, a tele-operated anthropomorphic
robotic arm and hand is designed and built as a versatile robotic arm
system. The robot has the ability to manipulate objects such as pick
and place operations. It is also able to function by itself, in
standalone mode.
Firstly, the robotic arm is built in order to interface with a personal
computer via a serial servo controller circuit board. The circuit board
enables user to completely control the robotic arm and moreover,
enables feedbacks from user. The control circuit board uses a
powerful integrated microcontroller, a PIC (Programmable Interface
Controller). The PIC is firstly programmed using BASIC (Beginner-s
All-purpose Symbolic Instruction Code) and it is used as the 'brain'
of the robot. In addition a user friendly Graphical User Interface
(GUI) is developed as the serial servo interface software using
Microsoft-s Visual Basic 6.
The second part of the project is to use speech recognition control
on the robotic arm. A speech recognition circuit board is constructed
with onboard components such as PIC and other integrated circuits. It
replaces the computers- Graphical User Interface. The robotic arm is
able to receive instructions as spoken commands through a
microphone and perform operations with respect to the commands
such as picking and placing operations.
Abstract: The increased use of biodiesel implies variations on both greenhouse gases and air pollutant emissions. Some studies point out that the use of biodiesel blends on diesel can help in controlling air pollution and promote a reduction of CO2 emissions. Reductions on PM, SO2, VOC and CO emissions are also expected, however NOx emissions may increase, which may potentiate O3 formation. This work aims to assess the impact of the biodiesel use on air quality, through a numerical modeling study, taking the Northern region of Portugal as a case study. The emission scenarios are focused on 2008 (baseline year) and 2020 (target year of Renewable Energy Directive-RED) and on three biodiesel blends (B0, B10 and B20). In a general way the use of biodiesel by 2020 will reduce the CO2 and air pollutants emissions in the Northern Portugal, improving air quality. However it will be in a very small extension.
Abstract: Voltage collapse is instability of heavily loaded electric
power systems that cause to declining voltages and blackout. Power
systems are predicated to become more heavily loaded in the future
decade as the demand for electric power rises while economic and
environmental concerns limit the construction of new transmission
and generation capacity. Heavily loaded power systems are closer to
their stability limits and voltage collapse blackouts will occur if
suitable monitoring and control measures are not taken. To control
transmission lines, it can be used from FACTS devices.
In this paper Harmony search algorithm (HSA) and Genetic
Algorithm (GA) have applied to determine optimal location of
FACTS devices in a power system to improve power system stability.
Three types of FACTS devices (TCPAT, UPFS, and SVC) have been
introduced. Bus under voltage has been solved by controlling reactive
power of shunt compensator. Also a combined series-shunt
compensators has been also used to control transmission power flow
and bus voltage simultaneously.
Different scenarios have been considered. First TCPAT, UPFS, and
SVC are placed solely in transmission lines and indices have been
calculated. Then two types of above controller try to improve
parameters randomly. The last scenario tries to make better voltage
stability index and losses by implementation of three types controller
simultaneously. These scenarios are executed on typical 34-bus test
system and yields efficiency in improvement of voltage profile and
reduction of power losses; it also may permit an increase in power
transfer capacity, maximum loading, and voltage stability margin.
Abstract: New generation mobile communication networks have
the ability of supporting triple play. In order that, Orthogonal
Frequency Division Multiplexing (OFDM) access techniques have
been chosen to enlarge the system ability for high data rates
networks. Many of cross-layer modeling and optimization schemes
for Quality of Service (QoS) and capacity of downlink multiuser
OFDM system were proposed. In this paper, the Maximum Weighted
Capacity (MWC) based resource allocation at the Physical (PHY)
layer is used. This resource allocation scheme provides a much better
QoS than the previous resource allocation schemes, while
maintaining the highest or nearly highest capacity and costing similar
complexity. In addition, the Delay Satisfaction (DS) scheduling at the
Medium Access Control (MAC) layer, which allows more than one
connection to be served in each slot is used. This scheduling
technique is more efficient than conventional scheduling to
investigate both of the number of users as well as the number of
subcarriers against system capacity. The system will be optimized for
different operational environments: the outdoor deployment scenarios
as well as the indoor deployment scenarios are investigated and also
for different channel models. In addition, effective capacity approach
[1] is used not only for providing QoS for different mobile users, but
also to increase the total wireless network's throughput.
Abstract: In this paper, a semi-fragile watermarking scheme is proposed for color image authentication. In this particular scheme, the color image is first transformed from RGB to YST color space, suitable for watermarking the color media. Each channel is divided into 4×4 non-overlapping blocks and its each 2×2 sub-block is selected. The embedding space is created by setting the two LSBs of selected sub-block to zero, which will hold the authentication and recovery information. For verification of work authentication and parity bits denoted by 'a' & 'p' are computed for each 2×2 subblock. For recovery, intensity mean of each 2×2 sub-block is computed and encoded upto six to eight bits depending upon the channel selection. The size of sub-block is important for correct localization and fast computation. For watermark distribution 2DTorus Automorphism is implemented using a private key to have a secure mapping of blocks. The perceptibility of watermarked image is quite reasonable both subjectively and objectively. Our scheme is oblivious, correctly localizes the tampering and able to recovery the original work with probability of near one.
Abstract: The analytical prediction of the decay heat results
from the fast neutron fission of actinides was initiated under a project, 10-MAT1134-3, funded by king Abdulaziz City of Science
and Technology (KASCT), Long-Term Comprehensive National Plan for Science, Technology and Innovations, managed by a team
from King Abdulaziz University (KAU), Saudi Arabia, and
supervised by Argonne National Laboratory (ANL) has collaborated
with KAU's team to assist in the computational analysis. In this paper, the numerical solution of coupled linear differential equations
that describe the decays and buildups of minor fission product MFA, has been used to predict the total decay heat and its components from the fast neutron fission of 235U and 239Pu. The reliability of the present approach is illustrated via systematic
comparisons with the measurements reported by the University of
Tokyo, in YAYOI reactor.
Abstract: this scientific article considers the peculiarities of
ecology of culture and ecological outlook from cultural and
anthropological aspect of Turkic languages speaking peoples in the
Central Asia. The ecology of culture of Turkic languages speaking
peoples in the Central Asia, formed under the influence of climatic,
geographical, economic, religious, ethno cultural and political factors
and defining the originality of traditions which have laid down in its
basis and functioned, as its components, causes an interest and
urgency simultaneously, representing the sample of life of the Person
in the World by which it is necessary to be guided today.
Abstract: The myocardial sintigraphy is an imaging modality which provides functional informations. Whereas, coronarography modality gives useful informations about coronary arteries anatomy. In case of coronary artery disease (CAD), the coronarography can not determine precisely which moderate lesions (artery reduction between 50% and 70%), known as the “gray zone", are haemodynamicaly significant. In this paper, we aim to define the relationship between the location and the degree of the stenosis in coronary arteries and the observed perfusion on the myocardial scintigraphy. This allows us to model the impact evolution of these stenoses in order to justify a coronarography or to avoid it for patients suspected being in the gray zone. Our approach is decomposed in two steps. The first step consists in modelling a coronary artery bed and stenoses of different location and degree. The second step consists in modelling the left ventricle at stress and at rest using the sphercical harmonics model and myocardial scintigraphic data. We use the spherical harmonics descriptors to analyse left ventricle model deformation between stress and rest which permits us to conclude if ever an ischemia exists and to quantify it.