Abstract: The institutions seek to improve their performance
and quality of service, so that their patients are satisfied. This
research project aims, conduct a time study program in the area of
gynecological surgery, to determine the current level of capacity and
optimize the programming time in order to adequately respond to
demand. The system is analyzed by waiting lines and uses the
simulation using ARENA to evaluate proposals for improvement and
optimization programming time each of the surgeries.
Abstract: Batteries and fuel cells contain a great potential to back up severe photovoltaic power fluctuations under inclement weather conditions. In this paper comparison between batteries and fuel cells is carried out in detail only for their PV power backup options, so their common attributes and different attributes is discussed. Then, the common and different attributes are compared; accordingly, the fuel cell is selected as the backup of Photovoltaic system. Finally, environmental evaluation of the selected hybrid plant was made in terms of plant-s land requirement and lifetime CO2 emissions, and then compared with that of the conventional fossilfuel power generating forms.
Abstract: Genetic Folding (GF) a new class of EA named as is
introduced for the first time. It is based on chromosomes composed
of floating genes structurally organized in a parent form and
separated by dots. Although, the genotype/phenotype system of GF
generates a kernel expression, which is the objective function of
superior classifier. In this work the question of the satisfying
mapping-s rules in evolving populations is addressed by analyzing
populations undergoing either Mercer-s or none Mercer-s rule. The
results presented here show that populations undergoing Mercer-s
rules improve practically models selection of Support Vector
Machine (SVM). The experiment is trained multi-classification
problem and tested on nonlinear Ionosphere dataset. The target of this
paper is to answer the question of evolving Mercer-s rule in SVM
addressed using either genetic folding satisfied kernel-s rules or not
applied to complicated domains and problems.
Abstract: Sarkhoon gas plant, located in south of Iran, has been installed to removal H2S contained in a high pressure natural gas stream. The solvent used for the H2S removal from gaseous stream is 34% by weight (wt%) Di-ethanol amine (DEA) solutions. Due to increasing concentration of heat stable salt (HSS) in solvent, corrosivity of amine solution had been increased. Reports indicated that there was corrosion on the shell of regeneration column. Because source formation of HSS was unknown, we decided to control the amount of HSS at the limit less than 3% wt amine solvent. Therefore, two small columns were filled by strong anionic base and carbon active, and then polluted amine was passed through beds. Finally a temporary amine recovery package on industrial scale was made based on laboratory’s results. From economical point of view we could save $700000 beside corrosion occurrence of the stripping column has been vigorously decreased.
Abstract: Lean, which was initially developed by Toyota, is
widely implemented in other companies to improve competitiveness.
This research is an attempt to identify the adoption of lean in the
production system of Malaysian car manufacturer, Proton using case
study approach. To gain the in-depth information regarding lean
implementation, an activity on the assembly line called Set Parts
Supply (SPS) was studied. The result indicates that by using lean
principles, tools and techniques in the implementation of SPS enabled
to achieve the goals on safety, quality, cost, delivery and morale. The
implementation increased the size of the workspace, improved the
quality of assembly and the delivery of parts supply, reduced the
manpower, achieved cost savings on electricity and also increased the
motivation of manpower in respect of attendance at work. A
framework of SPS implementation is suggested as a contribution for
lean practices in production system.
Abstract: Smoke from domestic wood burning has been
identified as a major contributor to air pollution, motivating detailed
emission measurements under controlled conditions. A series of
experiments was performed to characterise the emissions from wood
combustion in a fireplace and in a woodstove of two common species
of trees grown in Spain: Pyrenean oak (Quercus pyrenaica) and
black poplar (Populus nigra). Volatile organic compounds (VOCs) in
the exhaust emissions were collected in Tedlar bags, re-sampled in
sorbent tubes and analysed by thermal desorption-gas
chromatography-flame ionisation detection. Pyrenean oak presented
substantially higher emissions in the woodstove than in the fireplace,
for the majority of compounds. The opposite was observed for
poplar. Among the 45 identified species, benzene and benzenerelated
compounds represent the most abundant group, followed by
oxygenated VOCs and aliphatics. Emission factors obtained in this
study are generally of the same order than those reported for
residential experiments in the USA.
Abstract: In this study, multiwall carbon nanotubes (MWNTs)
were modified with nitric acid chemically and by dielectric barrier
discharge (DBD) plasma in an oxygen-based atmosphere. Used
carbon nanotubes (CNTs) were prepared by chemical vapour
deposition (CVD) floating catalyst method. For removing amorphous
carbon and metal catalyst, MWNTs were exposed to dry air and
washed with hydrochloric acid. Heating purified CNTs under helium
atmosphere caused elimination of acidic functional groups. Fourier
transformed infrared spectroscopy (FTIR) shows formation of
oxygen containing groups such as C=O and COOH. Brunauer,
Emmett, Teller (BET) analysis revealed that functionalization causes
generation of defects on the sidewalls and opening of the ends of
CNTs. Results of temperature-programmed desorption (TPD) and gas
chromatography(GC) indicate that nitric acid treatment create more
acidic groups than plasma treatment.
Abstract: Protein and Esterase electrophoresis were used to
genetically identify two Saudi tick species. Engorged females of the
camel tick Hyalomma dromedarii (Koch) (Acari: Ixodidae) and the
cattle tick Boophilus annulatus (Say) (Acari: Ixodidae) ticks
collected from infested camels and cattle in the animals resting
house at Hail region in KSA were used. The results showed that
there are a variation in both of protein and esterase activity levels and
a high polymorphism within and between the genera and species of
Hyalomma and Boophilus . In conclusion, the protein and esterase
electrophoretic analysis used in the present study could successfully
distinguish among tick species, commonly found in Saudi Arabia.
Abstract: This paper presents the study of hardness profile of spur gear heated by induction heating process in function of the machine parameters, such as the power (kW), the heating time (s) and the generator frequency (kHz). The global work is realized by 3D finite-element simulation applied to the process by coupling and resolving the electromagnetic field and the heat transfer problems, and it was performed in three distinguished steps. First, a Comsol 3D model was built using an adequate formulation and taking into account the material properties and the machine parameters. Second, the convergence study was conducted to optimize the mesh. Then, the surface temperatures and the case depths were deeply analyzed in function of the initial current density and the heating time in medium frequency (MF) and high frequency (HF) heating modes and the edge effect were studied. Finally, the simulations results are validated using experimental tests.
Abstract: The soil moisture content is an important property of
the soil. The results of mean weekly gravimetric soil moisture
content, measured for the three soil layers within the A horizon,
showed that it was higher for the top 5 cm over the whole period of
monitoring (15/7/2004 up to 10/11/05) with the variation becoming
greater during winter time. This reflects the pattern of rainfall in
Ireland which is spread over the whole year and shows that light
rainfall events during summer time were compensated by loss
through evapotranspiration, but only in the top 5 cm of soil. This
layer had the highest porosity and highest moisture holding capacity
due to the high content of organic matter. The gravimetric soil
moisture contents of the top 5 cm and the underlying 5-15 and 15-25
cm layers show that bottom site of the Hill Field had higher soil
moisture content than the middle and top sites during the whole
period of monitoring.
Abstract: This is an application research presenting the
improvement of production quality using the six sigma solutions and
the analyses of benefit-cost ratio. The case of interest is the
production of tile-concrete. Such production has faced with the
problem of high nonconforming products from an inappropriate
surface coating and had low process capability based on the strength
property of tile. Surface coating and tile strength are the most critical
to quality of this product. The improvements followed five stages of
six sigma solutions. After the improvement, the production yield was
improved to 80% as target required and the defective products from
coating process was remarkably reduced from 29.40% to 4.09%. The
process capability based on the strength quality was increased from
0.87 to 1.08 as customer oriented. The improvement was able to save
the materials loss for 3.24 millions baht or 0.11 million dollars. The
benefits from the improvement were analyzed from (1) the reduction
of the numbers of non conforming tile using its factory price for
surface coating improvement and (2) the materials saved from the
increment of process capability. The benefit-cost ratio of overall
improvement was high as 7.03. It was non valuable investment in
define, measure, analyses and the initial of improve stages after that
it kept increasing. This was due to there were no benefits in define,
measure, and analyze stages of six sigma since these three stages
mainly determine the cause of problem and its effects rather than
improve the process. The benefit-cost ratio starts existing in the
improve stage and go on. Within each stage, the individual benefitcost
ratio was much higher than the accumulative one as there was an
accumulation of cost since the first stage of six sigma. The
consideration of the benefit-cost ratio during the improvement
project helps make decisions for cost saving of similar activities
during the improvement and for new project. In conclusion, the
determination of benefit-cost ratio behavior through out six sigma
implementation period provides the useful data for managing quality
improvement for the optimal effectiveness. This is the additional
outcome from the regular proceeding of six sigma.
Abstract: Sharing the manufacturing facility through remote
operation and monitoring of a machining process is challenge for
effective use the production facility. Several automation tools in term
of hardware and software are necessary for successfully remote
operation of a machine. This paper presents a prototype of workpiece
holding attachment for remote operation of milling process by self
configuration the workpiece setup. The prototype is designed with
mechanism to reorient the work surface into machining spindle
direction with high positioning accuracy. Variety of parts geometry
is hold by attachment to perform single setup machining. Pin type
with array pattern additionally clamps the workpiece surface from
two opposite directions for increasing the machining rigidity.
Optimum pins configuration for conforming the workpiece geometry
with minimum deformation is determined through hybrid algorithms,
Genetic Algorithms (GA) and Particle Swarm Optimization (PSO).
Prototype with intelligent optimization technique enables to hold
several variety of workpiece geometry which is suitable for
machining low of repetitive production in remote operation.
Abstract: Electrospinning is a broadly used technology to obtain
polymeric nanofibers ranging from several micrometers down to
several hundred nanometers for a wide range of applications. It offers
unique capabilities to produce nanofibers with controllable porous
structure. With smaller pores and higher surface area than regular
fibers, electrospun fibers have been successfully applied in various
fields, such as, nanocatalysis, tissue engineering scaffolds, protective
clothing, filtration, biomedical, pharmaceutical, optical electronics,
healthcare, biotechnology, defense and security, and environmental
engineering. In this study, polyurethane nanofibers were obtained
under different electrospinning parameters. Fiber morphology and
diameter distribution were investigated in order to understand them
as a function of process parameters.
Abstract: Software Development Risks Identification (SDRI),
using Fault Tree Analysis (FTA), is a proposed technique to identify
not only the risk factors but also the causes of the appearance of the
risk factors in software development life cycle. The method is based
on analyzing the probable causes of software development failures
before they become problems and adversely affect a project. It uses
Fault tree analysis (FTA) to determine the probability of a particular
system level failures that are defined by A Taxonomy for Sources of
Software Development Risk to deduce failure analysis in which an
undesired state of a system by using Boolean logic to combine a
series of lower-level events. The major purpose of this paper is to use
the probabilistic calculations of Fault Tree Analysis approach to
determine all possible causes that lead to software development risk
occurrence
Abstract: Conventionally the selection of parameters depends
intensely on the operator-s experience or conservative technological
data provided by the EDM equipment manufacturers that assign
inconsistent machining performance. The parameter settings given by
the manufacturers are only relevant with common steel grades. A
single parameter change influences the process in a complex way.
Hence, the present research proposes artificial neural network (ANN)
models for the prediction of surface roughness on first commenced
Ti-15-3 alloy in electrical discharge machining (EDM) process. The
proposed models use peak current, pulse on time, pulse off time and
servo voltage as input parameters. Multilayer perceptron (MLP) with
three hidden layer feedforward networks are applied. An assessment
is carried out with the models of distinct hidden layer. Training of the
models is performed with data from an extensive series of
experiments utilizing copper electrode as positive polarity. The
predictions based on the above developed models have been verified
with another set of experiments and are found to be in good
agreement with the experimental results. Beside this they can be
exercised as precious tools for the process planning for EDM.
Abstract: The bypass exhaust system of a 160 MW combined cycle has been modeled and analyzed using numerical simulation in 2D prospective. Analysis was carried out using the commercial numerical simulation software, FLUENT 6.2. All inputs were based on the technical data gathered from working conditions of a Siemens V94.2 gas turbine, installed in the Yazd power plant. This paper deals with reduction of pressure drop in bypass exhaust system using turning vanes mounted in diverter box in order to alleviate turbulent energy dissipation rate above diverter box. The geometry of such turning vanes has been optimized based on the flow pattern at diverter box inlet. The results show that the use of optimized turning vanes in diverter box can improve the flow pattern and eliminate vortices around sharp edges just before the silencer. Furthermore, this optimization could decrease the pressure drop in bypass exhaust system and leads to higher plant efficiency.
Abstract: Phishing scheme is a new emerged security issue of
E-Commerce Crime in globalization. In this paper, the legal scaffold
of Malaysia, United States and United Kingdom are analyzed and
followed by discussion on critical issues that rose due to phishing
activities. The result revealed that inadequacy of current legal
framework is the main challenge to govern this epidemic. However,
lack of awareness among consumers, crisis on merchant-s
responsibility and lack of intrusion reports and incentive arrangement
contributes to phishing proliferating. Prevention is always better than
curb. By the end of this paper, some best practices for consumers and
corporations are suggested.
Abstract: Abstract–Indoor air (VOCs) samples were collected
simultaneously from variety of indoors (e.g. living rooms, baby-s
rooms) and outdoor environments which were voluntarily selected
from the houses in which pregnant residents live throughout Ankara.
This is the first comprehensive study done in Turkey starting from
prenatal period and continued till the babies had one year old. VOCs
levels were measured over 76 homes. Air samples were collected in
Tenax TA sorbent filled tubes with active sampling method and
analyzed with Thermal Desorber and Gas Chromatography/Mass
spectrometry (TD-GC/MS). At the first sampling period in the baby-s
rooms maximum concentration of toluene was measured about
240.77μg.m-3 and in the living rooms maximum concentration of
naphthalene was 180.24μg.m-3. At the second sampling period in the
baby-s rooms maximum concentration of toluene was measured
about 144.97μg.m-3 and in the living rooms maximum concentration
of naphthalene was 247.89μg.m-3. Concentration of TVOCs in the
first period was generally higher than the second period.
Abstract: In cancer progress, the optical properties of tissues
like absorption and scattering coefficient change, so by these
changes, we can trace the progress of cancer, even it can be applied
for pre-detection of cancer. In this paper, we investigate the effects of
changes of optical properties on light penetrated into tissues. The
diffusion equation is widely used to simulate light propagation into
biological tissues. In this study, the boundary integral method (BIM)
is used to solve the diffusion equation. We illustrate that the changes
of optical properties can modified the reflectance or penetrating light.
Abstract: In order to assess optical fiber reliability in different environmental and stress conditions series of testing are performed simulating overlapping of chemical and mechanical controlled varying factors. Each series of testing may be compared using statistical processing: i.e. Weibull plots. Due to the numerous data to treat, a software application has appeared useful to interpret selected series of experiments in function of envisaged factors. The current paper presents a software application used in the storage, modelling and interpretation of experimental data gathered from optical fibre testing. The present paper strictly deals with the software part of the project (regarding the modelling, storage and processing of user supplied data).