Abstract: In geophysical exploration surveys, the quality of acquired data holds significant importance before executing the data processing and interpretation phases. In this study, 2D seismic reflection survey data of Fort Abbas area, Cholistan Desert, Pakistan was taken as test case in order to assess its quality on statistical bases by using normalized root mean square error (NRMSE), Cronbach’s alpha test (α) and null hypothesis tests (t-test and F-test). The analysis challenged the quality of the acquired data and highlighted the significant errors in the acquired database. It is proven that the study area is plain, tectonically least affected and rich in oil and gas reserves. However, subsurface 3D modeling and contouring by using acquired database revealed high degrees of structural complexities and intense folding. The NRMSE had highest percentage of residuals between the estimated and predicted cases. The outcomes of hypothesis testing also proved the biasness and erraticness of the acquired database. Low estimated value of alpha (α) in Cronbach’s alpha test confirmed poor reliability of acquired database. A very low quality of acquired database needs excessive static correction or in some cases, reacquisition of data is also suggested which is most of the time not feasible on economic grounds. The outcomes of this study could be used to assess the quality of large databases and to further utilize as a guideline to establish database quality assessment models to make much more informed decisions in hydrocarbon exploration field.
Abstract: The main aim of this paper is to dedicate the belt drive system faults like cogs missing, misalignment and belt worm using vibration analysis technique. Experimentally, the belt drive test-rig is equipped to measure vibrations signals under different operating conditions. Finite element 3D model of belt drive system is created and vibration response analyzed using commercial finite element software ABAQUS/CAE. Root mean square (RMS) and Crest Factor will serve as indicators of average amplitude of envelope analysis signals. The vibration signals pattern obtained from the simulation model and experimental data have the same characteristics. It can be concluded that each case of the RMS is more effective in detecting the defect for acceleration response. While Crest Factor parameter has a response with the displacement and velocity of vibration signals. Also it can be noticed that the model has difficulty in completing the solution when the misalignment angle is higher than 1 degree.
Abstract: Use of base isolators in the seismic design of structures has attracted considerable attention in recent years. The major concern in the design of these structures is to have enough lateral stability to resist wind and seismic forces. There are different systems providing such isolation, among them there are friction- pendulum base isolation systems (FPS) which are rather widely applied nowadays involving to both affordable cost and high fundamental periods. These devices are characterised by a stiff resistance against wind loads and to be flexible to the seismic tremors, which make them suitable for different situations. In this paper, a 3D numerical investigation is done considering the seismic response of a twelve-storey steel building retrofitted with a FPS. Fast nonlinear time history analysis (FNA) of Boumerdes earthquake (Algeria, May 2003) is considered for analysis and carried out using SAP2000 software. Comparisons between fixed base, bearing base isolated and braced structures are shown in a tabulated and graphical format. The results of the various alternatives studies to compare the structural response without and with this device of dissipation energy thus obtained were discussed and the conclusions showed the interesting potential of the FPS isolator. This system may to improve the dissipative capacities of the structure without increasing its rigidity in a significant way which contributes to optimize the quantity of steel necessary for its general stability.
Abstract: A field experiment was conducted in the Agricultural
Research Station, at El-Ghoraieb, Assiut to study dry seed yield
performance of two locally adapted cultivars (‘Azmerly’ and ‘Cream
7’) and two line introductions (IT81D-1032 and IT82D-812) of
common cowpea (Vigna unguiculata (L.) Walp) grown at three
different within-row spaces (20, 30 and 40 cm) and two planting
dates in the summer (April 15th and 30th) and in the fall season (Aug.
12th and 27th) of two successive seasons. The data showed that total
dry-seed yield produced by plants grown at 20 cm was greater than at
30 cm in all cvs/lines in both years. Increases in 1000-seed weight
were detected in cv ‘Azmerly’ and line IT82D-812 when they were
grown at 30 cm as compared with 20 cm in the summer season.
However, in the fall season such increases were found in all cvs/lines.
Planting at 40 cm produced seeds of greater weight than planting at
30 cm for all cvs/lines in the fall season and also in cv. Cream 7 and
line IT82D-812 in the summer season, while all cvs/lines in the fall
Planting on April 15th in the summer and also planting on Aug. 12th
in the fall had plants which showed increases in 1000-seed weight
and total dry-seed yield. The greatest 1000-seed weight was found in
the line IT81D-1032 in the summer season and in the line IT82D-812
in the fall season. The sum up results revealed that ‘Azmerly’
produced greater dry-seed yield than ‘Cream 7’ and both of them
were superior to the line IT82D-812 and IT81D-1032 in the summer
season. In the fall, however, the line IT82D-812 produced greater
dry-seed yield than the other cultivars/lines.
Abstract: The calcarenites carbonate rocks of the Quaternary ridges, which extend along the northwestern Mediterranean coastal plain of Egypt, represent an excellent model for the transformation of loose sediments to real sedimentary rocks by the different stages of meteoric diagenesis. The depositional and diagenetic fabrics of the rocks, in addition to the strata orientation, highly affect their ultimate compressive strength and other geotechnical properties.
There is a marked increase in the compressive strength (UCS) from the first to the fourth ridge rock samples. The lowest values are related to the loose packing, weakly cemented aragonitic ooid sediments with high porosity, besides the irregularly distributed of cement, which result in decreasing the ability of these rocks to withstand crushing under direct pressure. The high (UCS) values are attributed to the low porosity, the presence of micritic cement, the reduction in grain size and the occurrence of micritization and calcretization processes.
The strata orientation has a notable effect on the measured (UCS). The lowest values have been recorded for the samples cored in the inclined direction; whereas the highest values have been noticed in most samples cored in the vertical and parallel directions to bedding plane. In case of the inclined direction, the bedding planes were oriented close to the plane of maximum shear stress. The lowest and highest anisotropy values have been recorded for the first and the third ridges rock samples, respectively, which may attributed to the relatively homogeneity and well sorted grainstone of the first ridge rock samples, and relatively heterogeneity in grain and pore size distribution and degree of cementation of the third ridge rock samples, besides, the abundance of shell fragments with intraparticle pore spaces, which may produce lines of weakness within the rock.
Abstract: Simple design of a rotary valve system is capable of controlling intake and exhaust gases, which will eliminate the need of known complex mechanisms. The cost of material and production, maintenance, and noise level of the system can be further reduced. The new mechanism enables the elimination of the overlapping of valves work that reduces gas leakage. This paper examines theoretically the gas flow through the holes of a rotary valve design in a small engine. Preliminary results show that the new gas flow has many positive differences than a conventional poppet-valve system. New dependencies on the gas speed enable the finding of better solutions for the geometry of a rotary valve system that will result in a higher efficiency of an internal-combustion engine of the automotive industry.
Abstract: Calcium oxide (CaO) as carbon dioxide (CO2)
adsorbent at the elevated temperature has been very well-received
thus far. The CaO can be synthesized from natural calcium carbonate
(CaCO3) sources through the reversible calcination-carbonation
process. In the study, cockle shell has been selected as CaO
precursors. The objectives of the study are to investigate the
performance of calcination and carbonation with respect to different
temperature, heating rate, particle size and the duration time. Overall,
better performance is shown at the calcination temperature of 850oC
for 40 minutes, heating rate of 20oC/min, particle size of < 0.125mm
and the carbonation temperature is at 650oC. The synthesized
materials have been characterized by nitrogen physisorption and
surface morphology analysis. The effectiveness of the synthesized
cockle shell in capturing CO2 (0.72 kg CO2/kg adsorbent) which is
comparable to the commercialized adsorbent (0.60 kg CO2/kg
adsorbent) makes them as the most promising materials for CO2
capture.
Abstract: The last two decades witnessed some advances in the development of an Arabic character recognition (CR) system. Arabic CR faces technical problems not encountered in any other language that make Arabic CR systems achieve relatively low accuracy and retards establishing them as market products. We propose the basic stages towards a system that attacks the problem of recognizing online Arabic cursive handwriting. Rule-based methods are used to perform simultaneous segmentation and recognition of word portions in an unconstrained cursively handwritten document using dynamic programming. The output of these stages is in the form of a ranked list of the possible decisions. A new technique for text line separation is also used.
Abstract: Aerospace vehicles are subjected to non-uniform
thermal loading that may cause thermal buckling. A study was
conducted on the thermal post-buckling of shape memory alloy
composite plates subjected to the non-uniform tent-like temperature
field. The shape memory alloy wires were embedded within the
laminated composite plates to add recovery stress to the plates. The
non-linear finite element model that considered the recovery stress of
the shape memory alloy and temperature dependent properties of the
shape memory alloy and composite matrix along with its source
codes were developed. It was found that the post-buckling paths of
the shape memory alloy composite plates subjected to various tentlike
temperature fields were stable within the studied temperature
range. The addition of shape memory alloy wires to the composite
plates was found to significantly improve the post-buckling behavior
of laminated composite plates under non-uniform temperature
distribution.
Abstract: Proteins or genes that have similar sequences are likely to perform the same function. One of the most widely used techniques for sequence comparison is sequence alignment. Sequence alignment allows mismatches and insertion/deletion, which represents biological mutations. Sequence alignment is usually performed only on two sequences. Multiple sequence alignment, is a natural extension of two-sequence alignment. In multiple sequence alignment, the emphasis is to find optimal alignment for a group of sequences. Several applicable techniques were observed in this research, from traditional method such as dynamic programming to the extend of widely used stochastic optimization method such as Genetic Algorithms (GAs) and Simulated Annealing. A framework with combination of Genetic Algorithm and Simulated Annealing is presented to solve Multiple Sequence Alignment problem. The Genetic Algorithm phase will try to find new region of solution while Simulated Annealing can be considered as an alignment improver for any near optimal solution produced by GAs.
Abstract: In this research, the main aim is to investigate the
antimicrobial effectiveness of ammonyx solutions finishing on
Sweatshirt Sport with immersion method. 60 Male healthy subjects
(football player) participated in this study. They were dressed in a
Sweatshirt for 14 days and some microbes found on them were
investigated. The antimicrobial effect of different ammonyx
solutions(1/100, 1/500, 1/1000, 1/2000 v/v solutions of Ammonyx)
on the identified microbes was studied by the zone inhabitation
method in vitro. In the next step the Sweatshirt Sports were treated
with the same different solutions of ammonyx and the antimicrobial
effectiveness was assessed by colony count method in different times
and the results were compared whit untreated ones. Some mechanical
properties of treated cotton/polyester yarn that used in Sweatshirt
Sport were measured after 30 days and were compared with
untreated one. Finally after finishing, scanning electron microscopy
(SEM) was used to compare the surfaces of the finished and
unfinished specimens. The results showed the presence of five
pathogenic microbes on Sweatshirt Sports such as Escherichia coli,
Staphylococcus aureus, Aspergillus, Mucor and Candida. The
inhalation time for treated on Sweatshirt Sports improved. The
amount of colony growth on treated clothes reduced considerably
and moreover the mechanical tests results showed no significant
deterioration effect of studies properties in comparison to the
untreated yarn. The visual examination of the SEM indicated that the
antimicrobial treatments were applied usefully to fabrics.
Abstract: In this paper we present the first Arabic sentence
dataset for on-line handwriting recognition written on tablet pc. The
dataset is natural, simple and clear. Texts are sampled from daily
newspapers. To collect naturally written handwriting, forms are
dictated to writers. The current version of our dataset includes 154
paragraphs written by 48 writers. It contains more than 3800 words
and more than 19,400 characters. Handwritten texts are mainly
written by researchers from different research centers. In order to use
this dataset in a recognition system word extraction is needed. In this
paper a new word extraction technique based on the Arabic
handwriting cursive nature is also presented. The technique is applied
to this dataset and good results are obtained. The results can be
considered as a bench mark for future research to be compared with.
Abstract: A simple microstructure optical fiber design based on an octagonal cladding structure is presented for simultaneously controlling dispersion and leakage properties. The finite difference method with anisotropic perfectly matched boundary layer is used to investigate the guiding properties. It is demonstrated that octagonal photonic crystal fibers with four rings can assume negative ultra-flattened dispersion of -19 + 0.23 ps/nm/km in the wavelength range of 1.275 μm to 1.68 μm, nearly zero ultra-flattened dispersion of 0 ± 0.40 ps/nm/km in a 1.38 to 1.64 μm, and low confinement losses less than 10-3 dB/km in the entire band of interest.
Abstract: As the fossil fuels kept on depleting, intense research in developing hydrogen (H2) as the alternative fuel has been done to cater our tremendous demand for fuel. The potential of H2 as the ultimate clean fuel differs with the fossil fuel that releases significant amounts of carbon dioxide (CO2) into the surrounding and leads to the global warming. The experimental work was carried out to study the production of H2 from palm kernel shell steam gasification at different variables such as heating rate, steam to biomass ratio and adsorbent to biomass ratio. Maximum H2 composition which is 61% (volume basis) was obtained at heating rate of 100oCmin-1, steam/biomass of 2:1 ratio, and adsorbent/biomass of 1:1 ratio. The commercial adsorbent had been modified by utilizing the alcoholwater mixture. Characteristics of both adsorbents were investigated and it is concluded that flowability and floodability of modified CaO is significantly improved.
Abstract: fibers of pure cellulose can be made from some bacteria such as acetobacter xylinum. Bacterial cellulose fibers are very pure, tens of nm across and about 0.5 micron long. The fibers are very stiff and, although nobody seems to have measured the strength of individual fibers. Their stiffness up to 70 GPa. Fundamental strengths should be at least greater than those of the best commercial polymers, but best bulk strength seems to about the same as that of steel. They can potentially be produced in industrial quantities at greatly lowered cost and water content, and with triple the yield, by a new process. This article presents a critical review of the available information on the bacterial cellulose as a biological nonwoven fabric with special emphasis on its fermentative production and applications. Characteristics of bacterial cellulose biofabric with respect to its structure and physicochemical properties are discussed. Current and potential applications of bacterial cellulose in textile, nonwoven cloth, paper, films synthetic fiber coating, food, pharmaceutical and other industries are also presented.
Abstract: In this paper by using the port-controlled Hamiltonian
(PCH) systems theory, a full-order nonlinear controlled model is first
developed. Then a nonlinear passivity-based robust adaptive control
(PBRAC) of switched reluctance motor in the presence of external
disturbances for the purpose of torque ripple reduction and
characteristic improvement is presented. The proposed controller
design is separated into the inner loop and the outer loop controller.
In the inner loop, passivity-based control is employed by using
energy shaping techniques to produce the proper switching function.
The outer loop control is employed by robust adaptive controller to
determine the appropriate Torque command. It can also overcome the
inherent nonlinear characteristics of the system and make the whole
system robust to uncertainties and bounded disturbances. A 4KW 8/6
SRM with experimental characteristics that takes magnetic saturation
into account is modeled, simulation results show that the proposed
scheme has good performance and practical application prospects.
Abstract: The present study investigates numerically the
phenomenon of vortex-shedding and its suppression in twodimensional
mixed convective flow past a square cylinder under the
joint influence of buoyancy and free-stream orientation with respect
to gravity. The numerical experiments have been conducted at a
fixed Reynolds number (Re) of 100 and Prandtl number (Pr) of 0.71,
while Richardson number (Ri) is varied from 0 to 1.6 and freestream
orientation, α, is kept in the range 0o≤ α ≤ 90o, with 0o
corresponding to an upward flow and 90o representing a cross-flow
scenario, respectively. The continuity, momentum and energy
equations, subject to Boussinesq approximation, are discretized using
a finite difference method and are solved by a semi-explicit pressure
correction scheme. The critical Richardson number, leading to the
suppression of the vortex-shedding (Ric), is estimated by using
Stuart-Landau theory at various free-stream orientations and the
neutral curve is obtained in the Ri-α plane. The neutral curve
exhibits an interesting non-monotonic behavior with Ric first
increasing with increasing values of α upto 45o and then decreasing
till 70o. Beyond 70o, the neutral curve again exhibits a sharp
increasing asymptotic trend with Ric approaching very large values
as α approaches 90o. The suppression of vortex shedding is not
observed at α = 90o (cross-flow). In the unsteady flow regime, the
Strouhal number (St) increases with the increase in Richardson
number.
Abstract: Most Decision Support Systems (DSS) for waste
management (WM) constructed are not widely marketed and lack
practical applications. This is due to the number of variables and
complexity of the mathematical models which include the
assumptions and constraints required in decision making. The
approach made by many researchers in DSS modelling is to isolate a
few key factors that have a significant influence to the DSS. This
segmented approach does not provide a thorough understanding of
the complex relationships of the many elements involved. The
various elements in constructing the DSS must be integrated and
optimized in order to produce a viable model that is marketable and
has practical application. The DSS model used in assisting decision
makers should be integrated with GIS, able to give robust prediction
despite the inherent uncertainties of waste generation and the plethora
of waste characteristics, and gives optimal allocation of waste stream
for recycling, incineration, landfill and composting.
Abstract: Protective clothing limits heat transfer and hampers
task performance due to the increased weight. Militarism protective
clothing enables humans to operate in adverse environments. In the
selection and evaluation of militarism protective clothing attention
should be given to heat strain, ergonomic and fit issues next to the
actual protection it offers.
Fifty Male healthy subjects participated in the study. The subjects
were dressed in shorts, T-shirts, socks, sneakers and four deferent
kinds of militarism protective clothing such as CS, CSB, CS with
NBC protection and CS with NBC- protection added.
Ergonomically and psychological strains of every four cloths were
investigated on subjects by walking on a treadmill (7km/hour) with a
19.7 kg backpack. As a result of these tests were showed that, the
highest heart rate was found wearing the NBC-protection added
outfit, the highest temperatures were observed wearing NBCprotection
added, followed by respectively CS with NBC protection,
CSB and CS and the highest value for thermal comfort (implying
worst thermal comfort) was observed wearing NBC-protection
added.