Abstract: Computer-based optimization techniques can be employed to improve the efficiency of energy conversions processes, including reducing the aerodynamic loss in a thermal power plant turbomachine. In this paper, towards mitigating secondary flow losses, a design optimization workflow is implemented for the casing geometry of a 1.5 stage axial flow turbine that improves the turbine isentropic efficiency. The improved turbine is used in an open thermodynamic gas cycle with regeneration and cogeneration. Performance estimates are obtained by the commercial software Cycle – Tempo. Design and off design conditions are considered as well as variations in inlet air temperature. Reductions in both the natural gas specific fuel consumption and in CO2 emissions are predicted by using the gas turbine cycle fitted with the new casing design. These gains are attractive towards enhancing the competitiveness and reducing the environmental impact of thermal power plant.
Abstract: This paper presents the results obtained by numerical
simulation using the software ANSYS CFX-CFD for the air
pollutants dispersion in the atmosphere coming from the evacuation
of combustion gases resulting from the fuel combustion in an electric
thermal power plant. The model uses the Navier-Stokes equation to
simulate the dispersion of pollutants in the atmosphere. It is
considered as important factors in elaboration of simulation the
atmospheric conditions (pressure, temperature, wind speed, wind
direction), the exhaust velocity of the combustion gases, chimney
height and the obstacles (buildings). Using the air quality monitoring
stations it is measured the concentrations of main pollutants (SO2,
NOx and PM). The pollutants were monitored over a period of 3
months, after that the average concentration are calculated, which is
used by the software. The concentrations are: 8.915 μg/m3 (NOx),
9.587 μg/m3 (SO2) and 42 μg/m3 (PM). A comparison of test data
with simulation results demonstrated that CFX was able to describe
the dispersion of the pollutant as well the concentration of this
pollutants in the atmosphere.
Abstract: This paper presents quantitative component criticality importance indices applicable for identifying and ranking critical components in the phase of thermal power plants design. Identifying critical components for power plant reliability provides one important input to decision-making and guidance throughout the development project. The study of components criticality importance indices to several characteristic structural schemes of conventional thermal power plant is presented and discussed.
Abstract: The present study was conducted to investigate the
response of plants exposed to lignite-based thermal power plant
emission. For this purpose, five plant species were collected from 1.0
km distance (polluted site) and control plants were collected from
20.0 km distance (control site) to thermal power plant. The common
tree species Cassia siamea Lamk., Polyalthia longifolia. Sonn,
Acacia longifolia (Andrews) Wild., Azadirachta indica A.Juss, Ficus
religiosa L. were selected as test plants. Photosynthetic pigments
changes (chlorophyll a, chlorophyll b and carotenoids) and rubisco
enzyme modifications were studied. Reduction was observed in the
photosynthetic pigments of plants growing in polluted site and also
large sub unit of the rubisco enzyme was degraded in Azadirachta
indica A. Juss collected from polluted site.
Abstract: IMCS is Integrated Monitoring and Control System for
thermal power plant. This system consists of mainly two parts; controllers and OIS (Operator Interface System). These two parts are
connected by Ethernet-based communication. The controller side of communication is managed by CNet module and OIS side is managed
by data server of OIS. CNet module sends the data of controller to data
server and receives commend data from data server. To minimizes or
balance the load of data server, this module buffers data created by controller at every cycle and send buffered data to data server on request of data server. For multiple data server, this module manages
the connection line with each data server and response for each request
from multiple data server. CNet module is included in each controller
of redundant system. When controller fail-over happens on redundant system, this module can provide data of controller to data sever
without loss. This paper presents three main features – separation of get task, usage of ring buffer and monitoring communication status –of CNet module to carry out these functions.