Abstract: In this paper we introduce a new unit test technique
called déjà-vu object. Déjà-vu objects replace real objects used by
classes under test, allowing the execution of isolated unit tests. A
déjà-vu object is able to observe and record the behaviour of a real
object during real sessions, and to replace it during unit tests,
returning previously recorded results. Consequently déjà-vu object
technique can be useful when a bottom-up development and testing
strategy is adopted. In this case déjà-vu objects can increase test
portability and test source code readability. At the same time they
can reduce the time spent by programmers to develop test code and
the risk of incompatibility during the switching between déjà-vu and
production code.
Abstract: As there are also graph methods of circuit analysis in
addition to algebraic methods, it is, in theory, clearly possible to
carry out an analysis of a whole switched circuit in two-phase
switching exclusively by the graph method as well. This article deals
with two methods of full-graph solving of switched circuits: by
transformation graphs and by two-graphs. It deals with the circuit
switched capacitors and the switched current, too. All methods are
presented in an equally detailed steps to be able to compare.
Abstract: Performance of a limited Round-Robin (RR) rule is
studied in order to clarify the characteristics of a realistic sharing
model of a processor. Under the limited RR rule, the processor
allocates to each request a fixed amount of time, called a quantum, in a
fixed order. The sum of the requests being allocated these quanta is
kept below a fixed value. Arriving requests that cannot be allocated
quanta because of such a restriction are queued or rejected. Practical
performance measures, such as the relationship between the mean
sojourn time, the mean number of requests, or the loss probability and
the quantum size are evaluated via simulation. In the evaluation, the
requested service time of an arriving request is converted into a
quantum number. One of these quanta is included in an RR cycle,
which means a series of quanta allocated to each request in a fixed
order. The service time of the arriving request can be evaluated using
the number of RR cycles required to complete the service, the number
of requests receiving service, and the quantum size. Then an increase
or decrease in the number of quanta that are necessary before service is
completed is reevaluated at the arrival or departure of other requests.
Tracking these events and calculations enables us to analyze the
performance of our limited RR rule. In particular, we obtain the most
suitable quantum size, which minimizes the mean sojourn time, for the
case in which the switching time for each quantum is considered.
Abstract: In this paper, stabilization of an Active Magnetic Bearing (AMB) system with varying rotor speed using Sliding Mode Control (SMC) technique is considered. The gyroscopic effect inherited in the system is proportional to rotor speed in which this nonlinearity effect causes high system instability as the rotor speed increases. Also, transformation of the AMB dynamic model into a new class of uncertain system shows that this gyroscopic effect lies in the mismatched part of the system matrix. Moreover, the current gain parameter is allowed to be varied in a known bound as an uncertainty in the input matrix. SMC design method is proposed in which the sufficient condition that guarantees the global exponential stability of the reduced-order system is represented in Linear Matrix Inequality (LMI). Then, a new chattering-free control law is established such that the system states are driven to reach the switching surface and stay on it thereafter. The performance of the controller applied to the AMB model is demonstrated through simulation works under various system conditions.
Abstract: This paper discusses the approach of real-time
controlling of the energy management system using the data
acquisition tool of LabVIEW. The main idea of this inspiration was
to interface the Station (PC) with the system and publish the data on
internet using LabVIEW. In this venture, controlling and switching of
3 phase AC loads are effectively and efficiently done. The phases are
also sensed through devices. In case of any failure the attached
generator starts functioning automatically. The computer sends
command to the system and system respond to the request. The
modern feature is to access and control the system world-wide using
world wide web (internet). This controlling can be done at any time
from anywhere to effectively use the energy especially in developing
countries where energy management is a big problem. In this system
totally integrated devices are used to operate via remote location.
Abstract: Nowadays in applications of renewable energy sources
it is important to develop powerful and energy-saving photovoltaic
converters and to keep the prescriptions of the standards. In grid
connected PV converters the obvious solution to increase the
efficiency is to reduce the switching losses. Our new developed
control method reduces the switching losses and keeps the limitations
of the harmonic distortion standards. The base idea of the method is
the utilization of 3-state control causing discontinuous current mode
at low input power. In the following sections the control theory, the
realizations and the simulation results are presented.
Abstract: This paper proposes a new optimal feedback controller
for voltage source converters VSC's, for current regulated voltage
source converters, which allows compensate the harmonics of current
produced by nonlinear loads and load reactive power. The aim of the
present paper is to describe a novel switching signal generation
technique called optimal controller which guarantees that the injected
currents follow the reference currents determined by the
compensation strategy, with the smallest possible tracking error and
fixed switching frequency. It is compared with well-known
hysteresis current controller HCC. The validity of presented method
and its comparison with HCC is studied through simulation results.
Abstract: This paper is concerned with exponential stability and stabilization of switched linear systems with interval time-varying delays. The time delay is any continuous function belonging to a given interval, in which the lower bound of delay is not restricted to zero. By constructing a suitable augmented Lyapunov-Krasovskii functional combined with Leibniz-Newton-s formula, a switching rule for the exponential stability and stabilization of switched linear systems with interval time-varying delays and new delay-dependent sufficient conditions for the exponential stability and stabilization of the systems are first established in terms of LMIs. Numerical examples are included to illustrate the effectiveness of the results.
Abstract: Traditional optical networks are gradually evolving towards intelligent optical networks due to the need for faster bandwidth provisioning, protection and restoration of the network that can be accomplished with devices like optical switch, add drop multiplexer and cross connects. Since dense wavelength multiplexing forms the physical layer for intelligent optical networking, the roll of high speed all optical switch is important. This paper analyzes such an ultra-high speed polymer electro-optic switch. The performances of the 2x2 optical waveguide switch with rectangular, triangular and trapezoidal grating profiles on various device parameters are analyzed. The simulation result shows that trapezoidal grating is the optimized structure which has the coupling length of 81μm and switching voltage of 11V for the operating wavelength of 1550nm. The switching time for this proposed switch is 0.47 picosecond. This makes the proposed switch to be an important element in the intelligent optical network.
Abstract: A synchronous network-on-chip using wormhole packet switching
and supporting guaranteed-completion best-effort with low-priority (LP)
and high-priority (HP) wormhole packet delivery service is presented in
this paper. Both our proposed LP and HP message services deliver a good
quality of service in term of lossless packet completion and in-order message
data delivery. However, the LP message service does not guarantee minimal
completion bound. The HP packets will absolutely use 100% bandwidth of
their reserved links if the HP packets are injected from the source node with
maximum injection. Hence, the service are suitable for small size messages
(less than hundred bytes). Otherwise the other HP and LP messages, which
require also the links, will experience relatively high latency depending on the
size of the HP message. The LP packets are routed using a minimal adaptive
routing, while the HP packets are routed using a non-minimal adaptive routing
algorithm. Therefore, an additional 3-bit field, identifying the packet type,
is introduced in their packet headers to classify and to determine the type
of service committed to the packet. Our NoC prototypes have been also
synthesized using a 180-nm CMOS standard-cell technology to evaluate the
cost of implementing the combination of both services.
Abstract: A DC-to-DC converter for applications involving a
source with widely varying voltage conditions with loads requiring
constant voltage from full load down to no load is presented.
The switching regulator considered is a Buck converter with Pulse
Skipping Modulation control whereby pulses applied to the switch
are blocked or released on output voltage crossing a predetermined
value. Results of the study on the performance of regulator circuit
are presented. The regulator regulates over a wide input voltage range
with slightly higher ripple content and good transient response. Input
current spectrum indicates a good EMI performance with crowding
of components at low frequency range.
Abstract: In this article the influence of higher frequency effects
in addition to a special damper design on the electrical behavior of a
synchronous generator main exciter machine is investigated. On the
one hand these machines are often highly stressed by harmonics from
the bridge rectifier thus facing additional eddy current losses. On the
other hand the switching may cause the excitation of dangerous
voltage peaks in resonant circuits formed by the diodes of the
rectifier and the commutation reactance of the machine. Therefore
modern rotating exciters are treated like synchronous generators
usually modeled with a second order equivalent circuit. Hence the
well known Standstill Frequency Response Test (SSFR) method is
applied to a test machine in order to determine parameters for the
simulation. With these results it is clearly shown that higher
frequencies have a strong impact on the conventional equivalent
circuit model. Because of increasing field displacement effects in the
stranded armature winding the sub-transient reactance is even smaller
than the armature leakage at high frequencies. As a matter of fact this
prevents the algorithm to find an equivalent scheme. This issue is
finally solved using Laplace transfer functions fully describing the
transient behavior at the model ports.
Abstract: The problem of delay-range-dependent exponential synchronization is investigated for Lur-e master-slave systems with delay feedback control and Markovian switching. Using Lyapunov- Krasovskii functional and nonsingular M-matrix method, novel delayrange- dependent exponential synchronization in mean square criterions are established. The systems discussed in this paper is advanced system, and takes all the features of interval systems, Itˆo equations, Markovian switching, time-varying delay, as well as the environmental noise, into account. Finally, an example is given to show the validity of the main result.
Abstract: This paper presents two different sequential switching hybrid-modulation strategies and implemented for cascaded multilevel inverters. Hybrid modulation strategies represent the combinations of Fundamental-frequency pulse width modulation (FFPWM) and Multilevel sinusoidal-modulation (MSPWM) strategies, and are designed for performance of the well-known Alternative Phase opposition disposition (APOD), Phase shifted carrier (PSC). The main characteristics of these modulations are the reduction of switching losses with good harmonic performance, balanced power loss dissipation among the devices with in a cell, and among the series-connected cells. The feasibility of these modulations is verified through spectral analysis, power loss analysis and simulation.
Abstract: Improving the reactive power and voltage profile of a
distribution substation is investigated in this paper. The purpose is to
properly determination of the shunt capacitors on/off status and
suitable tap changer (TC) position of a substation transformer. In
addition, the limitation of secondary bus voltage, the maximum
allowable number of switching operation in a day for on load tap
changer and on/off status of capacitors are taken into account. To
achieve these goals, an artificial neural network (ANN) is designed to
provide preliminary scheduling. Input of ANN is active and reactive
powers of transformer and its primary and secondary bus voltages.
The output of ANN is capacitors on/off status and TC position. The
preliminary schedule is further refined by fuzzy dynamic
programming in order to reach the final schedule. The operation of
proposed method in Q/V improving is compared with the results
obtained by operator operation in a distribution substation.
Abstract: An integrated vehicle dynamics control system is developed in this paper by a combination of active front steering (AFS) and direct yaw-moment control (DYC) based on fuzzy logic control. The control system has a hierarchical structure consisting of two layers. A fuzzy logic controller is used in the upper layer (yaw rate controller) to keep the yaw rate in its desired value. The yaw rate error and its rate of change are applied to the upper controlling layer as inputs, where the direct yaw moment control signal and the steering angle correction of the front wheels are the outputs. In the lower layer (fuzzy integrator), a fuzzy logic controller is designed based on the working region of the lateral tire forces. Depending on the directions of the lateral forces at the front wheels, a switching function is activated to adjust the scaling factor of the fuzzy logic controller. Using a nonlinear seven degrees of freedom vehicle model, the simulation results illustrate considerable improvements which are achieved in vehicle handling through the integrated AFS/DYC control system in comparison with the individual AFS or DYC controllers.
Abstract: In this study, a double-sided linear switched reluctance
motor (LSRM) drive was investigated as an alternative actuator for
vertical linear transportation applications such as a linear elevator
door, hospital and subway doors which move linearly and where
accurate position control and rapid response is requested. A prototype
sliding elevator door that is focused on a home elevator with LSRMs
is designed. The motor has 6/4 poles, 3 phases, 8A, 24V, 250 W and
250 N pull forces. Air gap between rotor and translator poles of the
designed motor and phase coil-s ideal inductance profile are obtained
in compliance with the geometric dimensions. Operation and
switching sections as motor and generator has been determined from
the inductance profile.
Abstract: The mechanical deformation and the electrical conductivity of lanthanum strontium cobalt ferrite oxide under uniaxial compression were investigated at various temperatures up to 1073 K. The material reveals a rather complex mechanical behaviour related to its ferroelasticity and completely different stress-strain curves are obtained during the 1st and 2nd loading cycles. A distinctive ferroelastic creep was observed at 293 K whilst typical ferroelastic stress-strain curve were obtained in the temperature range from 473 K to 873 K. At 1073 K, on the other hand, high-temperature creep deformation was observed instead of ferroelastic deformation. The conductivity increases with increasing compressive stress at all the temperatures. The increase in conductivity is related to both geometrical and piezoelectric effects. From 293 K to 873 K, where the material exhibits ferroelastic behaviour, the variation in the total conductivity decreases with increasing temperature. The contribution of the piezoelectric effect to the total conductivity variation also decreases with increasing temperature and the maximum in piezoconductivity has a value of about 0.75 % at 293 K for a compressive stress of 100 MPa. There is no effect of domain switching on conductivity except for the geometric effect. At 1073 K, the conductivity is simply proportional to the compressive strain.
Abstract: The performance of an image filtering system depends
on its ability to detect the presence of noisy pixels in the image. Most
of the impulse detection schemes assume the presence of salt and
pepper noise in the images and do not work satisfactorily in case of
uniformly distributed impulse noise. In this paper, a new algorithm is
presented to improve the performance of switching median filter in
detection of uniformly distributed impulse noise. The performance of
the proposed scheme is demonstrated by the results obtained from
computer simulations on various images.
Abstract: Ferroresonance is an electrical phenomenon in
nonlinear character, which frequently occurs in power system due to
transmission line faults and single or more-phase switching on the
lines as well as usage of the saturable transformers. In this study, the
ferroresonance phenomena are investigated under the modeling of the
West Anatolian Electric Power Network of 380 kV in Turkey. The
ferroresonance event is observed as a result of removing the loads at
the end of the lines. In this sense, two different cases are considered.
At first, the switching is applied at 2nd second and the ferroresonance
affects are observed between 2nd and 4th seconds in the voltage
variations of the phase-R. Hence the ferroresonance and nonferroresonance
parts of the overall data are compared with each
others using the Fourier transform techniques to show the
ferroresonance affects.