Abstract: A stack with a small critical temperature gradient is
desirable for a standing wave thermoacoustic engine to obtain a low
onset temperature difference (the minimum temperature difference to
start engine-s self-oscillation). The viscous and heat relaxation loss in
the stack determines the critical temperature gradient. In this work, a
dimensionless critical temperature gradient factor is obtained based
on the linear thermoacoustic theory. It is indicated that the
impedance determines the proportion between the viscous loss, heat
relaxation losses and the power production from the heat energy. It
reveals the effects of the channel dimensions, geometrical
configuration and the local acoustic impedance on the critical
temperature gradient in stacks. The numerical analysis shows that
there exists a possible optimum combination of these parameters
which leads to the lowest critical temperature gradient. Furthermore,
several different geometries have been tested and compared
numerically.
Abstract: High purity hydrogen and the valuable by-product of carbon nanotubes (CNTs) can be produced by the methane catalytic decomposition. The methane conversion and the performance of CNTs were determined by the choices of catalysts and the condition of decomposition reaction. In this paper, Ni/MgO and Ni/O-D (oxidized diamond) catalysts were prepared by wetness impregnation method. The effects of reaction temperature and space velocity of methane on the methane conversion were investigated in a fixed-bed. The surface area, structure and micrography were characterized with BET, XPS, SEM, EDS technology. The results showed that the conversion of methane was above 8% within 150 min (T=500) for 33Ni/O-D catalyst and higher than 25% within 120 min (T=650) for 41Ni/MgO catalyst. The initial conversion increased with the increasing temperature of the decomposition reaction, but their catalytic activities decreased rapidly while at too higher temperature. To decrease the space velocity of methane was propitious to promote the methane conversion, but not favor of the hydrogen yields. The appearance of carbon resulted from the methane decomposition lied on the support type and the condition of catalytic reaction. It presented as fiber shape on the surface of Ni/O-D at the relatively lower temperature such as 500 and 550, but as grain shape stacked on and overlayed on the surface of the metal nickel while at 650. The carbon fiber can form on the Ni/MgO surface at 650 and the diameter of the carbon fiber increased with the decreasing space velocity.
Abstract: This paper investigates vortex shedding processes
occurring at the end of a stack of parallel plates, due to an oscillating
flow induced by an acoustic standing wave within an acoustic
resonator. Here, Particle Image Velocimetry (PIV) is used to quantify
the vortex shedding processes within an acoustic cycle
phase-by-phase, in particular during the “ejection" of the fluid out of
the stack. Standard hot-wire anemometry measurement is also applied
to detect the velocity fluctuations near the end of the stack.
Combination of these two measurement techniques allowed a detailed
analysis of the vortex shedding phenomena. The results obtained show
that, as the Reynolds number varies (by varying the plate thickness
and drive ratio), different flow patterns of vortex shedding are
observed by the PIV measurement. On the other hand, the
time-dependent hot-wire measurements allow obtaining detailed
frequency spectra of the velocity signal, used for calculating
characteristic Strouhal numbers. The impact of the plate thickness and
the Reynolds number on the vortex shedding pattern has been
discussed. Furthermore, a detailed map of the relationship between the
Strouhal number and Reynolds number has been obtained and
discussed.
Abstract: By the application of an improved back-propagation
neural network (BPNN), a model of current densities for a solid oxide
fuel cell (SOFC) with 10 layers is established in this study. To build
the learning data of BPNN, Taguchi orthogonal array is applied to
arrange the conditions of operating parameters, which totally 7 factors
act as the inputs of BPNN. Also, the average current densities
achieved by numerical method acts as the outputs of BPNN.
Comparing with the direct solution, the learning errors for all learning
data are smaller than 0.117%, and the predicting errors for 27
forecasting cases are less than 0.231%. The results show that the
presented model effectively builds a mathematical algorithm to predict
performance of a SOFC stack immediately in real time.
Also, the calculating algorithms are applied to proceed with the
optimization of the average current density for a SOFC stack. The
operating performance window of a SOFC stack is found to be
between 41137.11 and 53907.89. Furthermore, an inverse predicting
model of operating parameters of a SOFC stack is developed here by
the calculating algorithms of the improved BPNN, which is proved to
effectively predict operating parameters to achieve a desired
performance output of a SOFC stack.
Abstract: The present work is motivated by the idea that the
layer deformation in anisotropic elasticity can be estimated from the
theory of interfacial dislocations. In effect, this work which is an
extension of a previous approach given by one of the authors
determines the anisotropic displacement fields and the critical
thickness due to a complex biperiodic network of MDs lying just
below the free surface in view of the arrangement of dislocations.
The elastic fields of such arrangements observed along interfaces
play a crucial part in the improvement of the physical properties of
epitaxial systems. New results are proposed in anisotropic elasticity
for hexagonal networks of MDs which contain intrinsic and extrinsic
stacking faults. We developed, using a previous approach based on
the relative interfacial displacement and a Fourier series formulation
of the displacement fields, the expressions of elastic fields when
there is a possible dissociation of MDs. The numerical investigations
in the case of the observed system Si/(111)Si with low twist angles
show clearly the effect of the anisotropy and thickness when the
misfit networks are dissociated.
Abstract: The small interfering RNA (siRNA) alters the
regulatory role of mRNA during gene expression by translational
inhibition. Recent studies show that upregulation of mRNA because
serious diseases like cancer. So designing effective siRNA with good
knockdown effects plays an important role in gene silencing. Various
siRNA design tools had been developed earlier. In this work, we are
trying to analyze the existing good scoring second generation siRNA
predicting tools and to optimize the efficiency of siRNA prediction
by designing a computational model using Artificial Neural Network
and whole stacking energy (%G), which may help in gene silencing
and drug design in cancer therapy. Our model is trained and tested
against a large data set of siRNA sequences. Validation of our results
is done by finding correlation coefficient of experimental versus
observed inhibition efficacy of siRNA. We achieved a correlation
coefficient of 0.727 in our previous computational model and we
could improve the correlation coefficient up to 0.753 when the
threshold of whole tacking energy is greater than or equal to -32.5
kcal/mol.
Abstract: Land surface temperature (LST) is an important
parameter to study in urban climate. The understanding of the
influence of biophysical factors could improve the establishment of
modeling urban thermal landscape. It is well established that climate
hold a great influence on the urban landscape. However, it has been
recognize that climate has a low priority in urban planning process,
due to the complex nature of its influence. This study will focus on
the relatively cloud free Landsat Thematic Mapper image of the study
area, acquired on the 2nd March 2006. Correlation analyses were
conducted to identify the relationship of LST to the biophysical
factors; vegetation indices, impervious surface, and albedo to
investigate the variation of LST. We suggest that the results can be
considered by the stackholders during decision-making process to
create a cooler and comfortable environment in the urban landscape
for city dwellers.
Abstract: As in today's semiconductor industries test costs can make up to 50 percent of the total production costs, an efficient test error detection becomes more and more important. In this paper, we present a new machine learning approach to test error detection that should provide a faster recognition of test system faults as well as an improved test error recall. The key idea is to learn a classifier ensemble, detecting typical test error patterns in wafer test results immediately after finishing these tests. Since test error detection has not yet been discussed in the machine learning community, we define central problem-relevant terms and provide an analysis of important domain properties. Finally, we present comparative studies reflecting the failure detection performance of three individual classifiers and three ensemble methods based upon them. As base classifiers we chose a decision tree learner, a support vector machine and a Bayesian network, while the compared ensemble methods were simple and weighted majority vote as well as stacking. For the evaluation, we used cross validation and a specially designed practical simulation. By implementing our approach in a semiconductor test department for the observation of two products, we proofed its practical applicability.
Abstract: In CMOS integrated circuit design there is a trade-off between static power consumption and technology scaling. Recently, the power density has increased due to combination of higher clock speeds, greater functional integration, and smaller process geometries. As a result static power consumption is becoming more dominant. This is a challenge for the circuit designers. However, the designers do have a few methods which they can use to reduce this static power consumption. But all of these methods have some drawbacks. In order to achieve lower static power consumption, one has to sacrifice design area and circuit performance. In this paper, we propose a new method to reduce static power in the CMOS VLSI circuit using Variable Body Biasing technique without being penalized in area requirement and circuit performance.
Abstract: Solid oxide fuel cells have been considered in the last years as one of the most promising technologies for very highefficiency electric energy generation from hydrogen or other hydrocarbons, both with simple fuel cell plants and with integrated gas turbine-fuel cell systems. In the present study, a detailed thermodynamic analysis has been carried out. Mass and exergy balances are performed not only for the whole plant but also for each component in order to evaluate the thermal efficiency of combined cycle. Moreover, different sources of irreversibilities within the SOFC stack have been discussed and a parametric study conducted to evaluate the effect of temperature as well as pressure on SOFC irreversibilities and its performance. In this investigation methane and hydrogen have been used for fueling the SOFC stack and combustion chamber.
Abstract: This study investigates the electrical performance of a
planar solid oxide fuel cell unit with cross-flow configuration when the fuel utilization gets higher and the fuel inlet flow are non-uniform.
A software package in this study solves two-dimensional,
simultaneous, partial differential equations of mass, energy, and
electro-chemistry, without considering stack direction variation. The
results show that the fuel utilization increases with a decrease in the molar flow rate, and the average current density decreases when the
molar flow rate drops. In addition, non-uniform Pattern A will induce more severe happening of non-reaction area in the corner of the fuel
exit and the air inlet. This non-reaction area deteriorates the average
current density and then deteriorates the electrical performance to –7%.
Abstract: Mechanical interaction between endothelial cells (ECs) and the extracellular matrix (or collagen gel) is known to influence the sprouting response of endothelial cells during angiogenesis. This influence is believed to impact on the capability of endothelial cells to sense soluble chemical cues. Quantitative analysis of endothelial-cell-mediated displacement of the collagen gel provides a means to explore this mechanical interaction. Existing analysis in this context is generally limited to 2D settings. In this paper, we investigate the mechanical interaction between endothelial cells and the extracellular matrix in terms of the endothelial-cellmediated displacement of the collagen gel in both 2D and 3D. Digital image correlation and Digital volume correlation are applied on confocal reflectance image stacks to analyze cell-mediated displacement of the gel. The skeleton of the sprout is extracted from phase contrast images and superimposed on the displacement field to further investigate the link between the development of the sprout and the displacement of the gel.
Abstract: This paper explores the effectiveness of machine
learning techniques in detecting firms that issue fraudulent financial
statements (FFS) and deals with the identification of factors
associated to FFS. To this end, a number of experiments have been
conducted using representative learning algorithms, which were
trained using a data set of 164 fraud and non-fraud Greek firms in the
recent period 2001-2002. The decision of which particular method to
choose is a complicated problem. A good alternative to choosing
only one method is to create a hybrid forecasting system
incorporating a number of possible solution methods as components
(an ensemble of classifiers). For this purpose, we have implemented
a hybrid decision support system that combines the representative
algorithms using a stacking variant methodology and achieves better
performance than any examined simple and ensemble method. To
sum up, this study indicates that the investigation of financial
information can be used in the identification of FFS and underline the
importance of financial ratios.
Abstract: In this paper a polymer electrolyte membrane (PEM)
fuel cell power system including burner, steam reformer, heat
exchanger and water heater has been considered to meet the
electrical, heating, cooling and domestic hot water loads of
residential building which in Tehran. The system uses natural gas as
fuel and works in CHP mode. Design and operating conditions of a
PEM fuel cell system is considered in this study. The energy
requirements of residential building and the number of fuel cell
stacks to meet them have been estimated. The method involved
exergy analysis and entropy generation thorough the months of the
year. Results show that all the energy needs of the building can be
met with 12 fuel cell stacks at a nominal capacity of 8.5 kW. Exergy
analysis of the CHP system shows that the increase in the ambient air
temperature from 1oC to 40oC, will have an increase of entropy
generation by 5.73%.Maximum entropy generates for 15 hour in 15th
of June and 15th of July is estimated to amount at 12624 (kW/K).
Entropy generation of this system through a year is estimated to
amount to 1004.54 GJ/k.year.
Abstract: Block replacement algorithms to increase hit ratio
have been extensively used in cache memory management. Among
basic replacement schemes, LRU and FIFO have been shown to be
effective replacement algorithms in terms of hit rates. In this paper,
we introduce a flexible stack-based circuit which can be employed in
hardware implementation of both LRU and FIFO policies. We
propose a simple and efficient architecture such that stack-based
replacement algorithms can be implemented without the drawbacks
of the traditional architectures. The stack is modular and hence, a set
of stack rows can be cascaded depending on the number of blocks in
each cache set. Our circuit can be implemented in conjunction with
the cache controller and static/dynamic memories to form a cache
system. Experimental results exhibit that our proposed circuit
provides an average value of 26% improvement in storage bits and its
maximum operating frequency is increased by a factor of two
Abstract: With deep development of software reuse, componentrelated
technologies have been widely applied in the development of
large-scale complex applications. Component identification (CI) is
one of the primary research problems in software reuse, by analyzing
domain business models to get a set of business components with high
reuse value and good reuse performance to support effective reuse.
Based on the concept and classification of CI, its technical stack is
briefly discussed from four views, i.e., form of input business models,
identification goals, identification strategies, and identification
process. Then various CI methods presented in literatures are
classified into four types, i.e., domain analysis based methods,
cohesion-coupling based clustering methods, CRUD matrix based
methods, and other methods, with the comparisons between these
methods for their advantages and disadvantages. Additionally, some
insufficiencies of study on CI are discussed, and the causes are
explained subsequently. Finally, it is concluded with some
significantly promising tendency about research on this problem.
Abstract: Magnetic and semiconductor nanomaterials exhibit
novel magnetic and optical properties owing to their unique size and
shape-dependent effects. With shrinking the size down to nanoscale
region, various anomalous properties that normally not present in bulk
start to dominate. Ability in harnessing of these anomalous properties
for the design of various advance electronic devices is strictly
dependent on synthetic strategies. Hence, current research has focused
on developing a rational synthetic control to produce high quality
nanocrystals by using organometallic approach to tune both size and
shape of the nanomaterials. In order to elucidate the growth
mechanism, transmission electron microscopy was employed as a
powerful tool in performing real time-resolved morphologies and
structural characterization of magnetic (Fe3O4) and semiconductor
(ZnO) nanocrystals. The current synthetic approach is found able to
produce nanostructures with well-defined shapes. We have found that
oleic acid is an effective capping ligand in preparing oxide-based
nanostructures without any agglomerations, even at high temperature.
The oleate-based precursors and capping ligands are fatty acid
compounds, which are respectively originated from natural palm oil
with low toxicity. In comparison with other synthetic approaches in
producing nanostructures, current synthetic method offers an effective
route to produce oxide-based nanomaterials with well-defined shapes
and good monodispersity. The nanocystals are well-separated with
each other without any stacking effect. In addition, the as-synthesized
nanopellets are stable in terms of chemically and physically if
compared to those nanomaterials that are previous reported. Further
development and extension of current synthetic strategy are being
pursued to combine both of these materials into nanocomposite form
that will be used as “smart magnetic nanophotocatalyst" for industry
waste water treatment.
Abstract: In this paper, we consider Wiener nonlinear model for solid oxide fuel cell (SOFC). The Wiener model of the SOFC consists of a linear dynamic block and a static output non-linearity followed by the block, in which linear part is approximated by state-space model and the nonlinear part is identified by a polynomial form. To control the SOFC system, we have to consider various view points such as operating conditions, another constraint conditions, change of load current and so on. A change of load current is the significant one of these for good performance of the SOFC system. In order to keep the constant stack terminal voltage by changing load current, the nonlinear model predictive control (MPC) is proposed in this paper. After primary control method is designed to guarantee the fuel utilization as a proper constant, a nonlinear model predictive control based on the Wiener model is developed to control the stack terminal voltage of the SOFC system. Simulation results verify the possibility of the proposed Wiener model and MPC method to control of SOFC system.
Abstract: The problem discussed in this paper involves packing fresh fish fileet of the northern Cod into a standard square container. The fish is first cleaned and split and then collected on a belt ready to be stacked in a container. The aim of our work is to pack the fish into the container with constraints on the amount of overlap allowed for the fileets. The current focus is to design a packing cell that can be real-time and of practical use, while finding the optimal solution to the degree of overlap and minimise the unused space of the container.
Abstract: A new concept for long-term reagent storage for Labon- a-Chip (LoC) devices is described. Here we present a polymer multilayer stack with integrated stick packs for long-term storage of several liquid reagents, which are necessary for many diagnostic applications. Stick packs are widely used in packaging industry for storing solids and liquids for long time. The storage concept fulfills two main requirements: First, a long-term storage of reagents in stick packs without significant losses and interaction with surroundings, second, on demand releasing of liquids, which is realized by pushing a membrane against the stick pack through pneumatic pressure. This concept enables long-term on-chip storage of liquid reagents at room temperature and allows an easy implementation in different LoC devices.