Abstract: Now-a-days, numbers of simulation software are
being used all over the world to solve Computational Fluid
Dynamics (CFD) related problems. In this present study, a
commercial CFD simulation software namely STAR-CCM+ is
applied to analyze the airflow characteristics inside a 2.5" hard
disk drive. Each step of the software is described adequately to
obtain the output and the data are verified with the theories to
justify the robustness of the simulation outcome. This study
gives an insight about the accuracy level of the CFD
simulation software to compute CFD related problems
although it largely depends upon the computer speed. Also
this study will open avenues for further research.
Abstract: This paper explores the issues that influence online retailing in Saudi Arabia. Retailers in Saudi Arabia have been reserved in their adoption of electronically delivered aspects of their business. Despite the fact that Saudi Arabia has the largest and fastest growth of ICT marketplaces in the Arab region, e-commerce activities are not progressing at the same speed. Only very few Saudi companies, mostly medium and large companies from the manufacturing sector, are involved in e-commerce implementation. Based on qualitative data collected by conducting interviews with 16 retailers and 16 potential customers in Saudi Arabia, several factors influencing online retailing diffusion in Saudi Arabia are identified. However, government support comes the highest and most influencing factor for online retailing growth as identified by both parties; retailers and potential customers in Saudi Arabia.
Abstract: In this report, an OTA which is used in fully
differential pipelined ADC was described. Using gain-boost
architecture with difference-ended amplifier, this OTA achieve
high-gain and high-speed. Besides, the CMFB circuit is also used, and
some methods are concerned to improve the performance. Then, by
optimization the layout design, OTA-s mismatch was reduced. This
design was using TSMC 0.18um CMOS process and simulation both
schematic and layout in Cadence. The result of the simulation shows
that the OTA has a gain up to 80dB,a unity gain bandwidth of about
1.437GHz for a 2pF load, a slew rate is about 428V/μs, a output swing
is 0.2V~1.35V, with the power supply of 1.8V, the power
consumption is 88mW. This amplifier was used in a 10bit 150MHz
pipelined ADC.
Abstract: In this paper, Speed Sensorless Indirect Field Oriented Control (IFOC) of a Permanent Magnet Synchronous machine (PMSM) is studied. The closed loop scheme of the drive system utilizes fuzzy speed and current controllers. Due to the well known drawbacks of the speed sensor, an algorithm is proposed in this paper to eliminate it. In fact, based on the model of the PMSM, the stator currents and rotor speed are estimated simultaneously using adaptive Luenberger observer for currents and MRAS (Model Reference Adaptive System) observer for rotor speed. To overcome the sensivity of this algorithm against parameter variation, adaptive for on line stator resistance tuning is proposed. The validity of the proposed method is verified by an extensive simulation work.
Abstract: In this work we will present a new approach for shot transition auto-detection. Our approach is based on the analysis of Spatio-Temporal Video Slice (STVS) edges extracted from videos. The proposed approach is capable to efficiently detect both abrupt shot transitions 'cuts' and gradual ones such as fade-in, fade-out and dissolve. Compared to other techniques, our method is distinguished by its high level of precision and speed. Those performances are obtained due to minimizing the problem of the boundary shot detection to a simple 2D image partitioning problem.
Abstract: In this paper presents a technique for developing the
computational efficiency in simulating double output induction
generators (DOIG) with two rotor circuits where stator transients are
to be included. Iterative decomposition is used to separate the flux–
Linkage equations into decoupled fast and slow subsystems, after
which the model order of the fast subsystems is reduced by
neglecting the heavily damped fast transients caused by the second
rotor circuit using integral manifolds theory. The two decoupled
subsystems along with the equation for the very slowly changing slip
constitute a three time-scale model for the machine which resulted in
increasing computational speed. Finally, the proposed method of
reduced order in this paper is compared with the other conventional
methods in linear and nonlinear modes and it is shown that this
method is better than the other methods regarding simulation
accuracy and speed.
Abstract: The performance of sensor-less controlled induction
motor drive depends on the accuracy of the estimated speed.
Conventional estimation techniques being mathematically complex
require more execution time resulting in poor dynamic response. The
nonlinear mapping capability and powerful learning algorithms of
neural network provides a promising alternative for on-line speed
estimation. The on-line speed estimator requires the NN model to be
accurate, simpler in design, structurally compact and computationally
less complex to ensure faster execution and effective control in real
time implementation. This in turn to a large extent depends on the
type of Neural Architecture. This paper investigates three types of
neural architectures for on-line speed estimation and their
performance is compared in terms of accuracy, structural
compactness, computational complexity and execution time. The
suitable neural architecture for on-line speed estimation is identified
and the promising results obtained are presented.
Abstract: To improve the characterization of blood flows, we propose a method which makes it possible to use the spectral analysis
of the Doppler signals. Our calculation induces a reasonable approximation, the error made on estimated speed reflects the fact
that speed depends on the flow conditions as well as on measurement parameters like the bore and the volume flow rate. The estimate of the Doppler signal frequency enables us to determine the maximum Doppler frequencie Fd max as well as the maximum flow speed. The
results show that the difference between the estimated frequencies
( Fde ) and the Doppler frequencies ( Fd ) is small, this variation tends to zero for important θ angles and it is proportional to the diameter D. The description of the speed of friction and the
coefficient of friction justify the error rate obtained.
Abstract: The concerns about clean environment and high oil
prices driving forces for the research on alternative fuels. The
research efforts directed towards improving the performance of C.I
engines using vegetable oil as fuel. The paper deals results of
performance of a four stroke, single cylinder C.I. engine by preheated
neat Karanja oil is done from 30
o
C to 100
o
C. The performance of the
engine was studied for a speed range between 1500 to 4000 rpm, with
the engine operated under full load conditions. The performance
parameters considered for comparing are brake specific fuel
consumption, thermal efficiency, brake power, Nox emission of the
engine. The engine offers lower thermal efficiency when it is
powered by preheated neat Karanja oil at higher speed. The power
developed and Nox emission increase with the increase in the fuel
inlet temperature and the specific fuel consumption is higher than
diesel fuel operation at all elevated fuel inlet temperature.
Abstract: The intention of this lessons is to assess the probability
of optical coherence tomography (OCT) for biometric recognition.
The OCT is the foundation on an optical signal acquisition and
processing method and has the micrometer-resolution. In this study,
we used the porcine skin for verifying the abovementioned means. The
porcine tissue was sound acknowledged for structural and
immunohistochemical similarity with human skin, so it could be
suitable for pre-clinical trial as investigational specimen. For this
reason, it was tattooed by the tattoo machine with the tattoo-pigment.
We detected the pattern of the tattooed skin by the OCT according to
needle speed. The result was consistent with the histology images.
This result showed that the OCT was effective to examine the tattooed
skin section noninvasively. It might be available to identify
morphological changes inside the skin.
Abstract: Asynchronous Transfer Mode (ATM) is widely used
in telecommunications systems to send data, video and voice at a
very high speed. In ATM network optimizing the bandwidth through
dynamic routing is an important consideration. Previous research
work shows that traditional optimization heuristics result in suboptimal
solution. In this paper we have explored non-traditional
optimization technique. We propose comparison of two such
algorithms - Genetic Algorithm (GA) and Tabu search (TS), based on
non-traditional Optimization approach, for solving the dynamic
routing problem in ATM networks which in return will optimize the
bandwidth. The optimized bandwidth could mean that some
attractive business applications would become feasible such as high
speed LAN interconnection, teleconferencing etc. We have also
performed a comparative study of the selection mechanisms in GA
and listed the best selection mechanism and a new initialization
technique which improves the efficiency of the GA.
Abstract: In the context of spectrum surveillance, a new method
to recover the code of spread spectrum signal is presented, while the
receiver has no knowledge of the transmitter-s spreading sequence. In
our previous paper, we used Genetic algorithm (GA), to recover
spreading code. Although genetic algorithms (GAs) are well known
for their robustness in solving complex optimization problems, but
nonetheless, by increasing the length of the code, we will often lead
to an unacceptable slow convergence speed. To solve this problem we
introduce Particle Swarm Optimization (PSO) into code estimation in
spread spectrum communication system. In searching process for
code estimation, the PSO algorithm has the merits of rapid
convergence to the global optimum, without being trapped in local
suboptimum, and good robustness to noise. In this paper we describe
how to implement PSO as a component of a searching algorithm in
code estimation. Swarm intelligence boasts a number of advantages
due to the use of mobile agents. Some of them are: Scalability, Fault
tolerance, Adaptation, Speed, Modularity, Autonomy, and
Parallelism. These properties make swarm intelligence very attractive
for spread spectrum code estimation. They also make swarm
intelligence suitable for a variety of other kinds of channels. Our
results compare between swarm-based algorithms and Genetic
algorithms, and also show PSO algorithm performance in code
estimation process.
Abstract: In contrast to conventional generators, self-excited induction generators are found to be most suitable machines for wind energy conversion in remote and windy areas due to many advantages over grid connected machines. This papers presents a Self-Excited Induction Generator (SEIG) driven by wind turbine and supplying an induction motor which is coupled to a centrifugal pump. A method to describe the steady state performance based on nodal analysis is presented. Therefore the advanced knowledge of the minimum excitation capacitor value is required. The effects of variation of excitation capacitance on system and rotor speed under different loading conditions have been analyzed and considered to optimize induction motor pump performances.
Abstract: In wireless communication system, a Decision Feedback Equalizer (DFE) to cancel the intersymbol interference (ISI) is required. In this paper, an exact convergence analysis of the (DFE) adapted by the Least Mean Square (LMS) algorithm during the training phase is derived by taking into account the finite alphabet context of data transmission. This allows us to determine the shortest training sequence that allows to reach a given Mean Square Error (MSE). With the intention of avoiding the problem of ill-convergence, the paper proposes an initialization strategy for the blind decision directed (DD) algorithm. This then yields a semi-blind DFE with high speed and good convergence.
Abstract: Among many different methods that are used for
optimizing different engineering problems mathematical (numerical)
optimization techniques are very important because they can easily
be used and are consistent with most of engineering problems. Many
studies and researches are done on stability analysis of three
dimensional (3D) slopes and the relating probable slip surfaces and
determination of factors of safety, but in most of them force
equilibrium equations, as in simplified 2D methods, are considered
only in two directions. In other words for decreasing mathematical
calculations and also for simplifying purposes the force equilibrium
equation in 3rd direction is omitted. This point is considered in just a
few numbers of previous studies and most of them have only given a
factor of safety and they haven-t made enough effort to find the most
probable slip surface. In this study shapes of the slip surfaces are
modeled, and safety factors are calculated considering the force
equilibrium equations in all three directions, and also the moment
equilibrium equation is satisfied in the slip direction, and using
nonlinear programming techniques the shape of the most probable
slip surface is determined. The model which is used in this study is a
3D model that is composed of three upper surfaces which can cover
all defined and probable slip surfaces. In this research the meshing
process is done in a way that all elements are prismatic with
quadrilateral cross sections, and the safety factor is defined on this
quadrilateral surface in the base of the element which is a part of the
whole slip surface. The method that is used in this study to find the
most probable slip surface is the non-linear programming method in
which the objective function that must get optimized is the factor of
safety that is a function of the soil properties and the coordinates of
the nodes on the probable slip surface. The main reason for using
non-linear programming method in this research is its quick
convergence to the desired responses. The final results show a good
compatibility with the previously used classical and 2D methods and
also show a reasonable convergence speed.
Abstract: In the process of polyethylene extrusion polymer
material similar to powder or granule is under compression, melting
and transmission operation and on base of special form, extrudate has
been produced. Twin-screw extruders are applicable in industries
because of their high capacity. The powder mixing with chemical
additives and melting with thermal and mechanical energy in three
zones (feed, compression and metering zone) and because of gear
pump and screw's pressure, converting to final product in latest plate.
Extruders with twin-screw and short distance between screws are
better than other types because of their high capacity and good
thermal and mechanical stress.
In this paper, process of polyethylene extrusion and various tapes
of extruders are studied. It is necessary to have an exact control on
process to producing high quality products with safe operation and
optimum energy consumption.
The granule size is depending on granulator motor speed. Results
show at constant feed rate a decrease in granule size was found whit
Increase in motor speed. Relationships between HDPE feed rate and
speed of granulator motor, main motor and gear pump are calculated
following as:
x = HDPE feed flow rate, yM = Main motor speed
yM = (-3.6076e-3) x^4+ (0.24597) x^3+ (-5.49003) x^2+ (64.22092)
x+61.66786 (1)
x = HDPE feed flow rate, yG = Gear pump speed
yG = (-2.4996e-3) x^4+ (0.18018) x^3+ (-4.22794) x^2+ (48.45536)
x+18.78880 (2)
x = HDPE feed flow rate, y = Granulator motor speed
10th Degree Polynomial Fit: y = a+bx+cx^2+dx^3... (3)
a = 1.2751, b = 282.4655, c = -165.2098,
d = 48.3106, e = -8.18715, f = 0.84997
g = -0.056094, h = 0.002358, i = -6.11816e-5
j = 8.919726e-7, k = -5.59050e-9
Abstract: This research deals with investigations on the “Active
Generator" under rotor speed variations and output frequency
control. It runs at turbine speed and it is connected to a three phase
electrical power grid which has its own frequency different from
turbine frequency. In this regard the set composed of a four phase
synchronous generator and a natural commutated matrix converter
(NCMC) made with thyristors, is called active generator. It replaces a
classical mechanical gearbox which introduces many drawbacks. The
main idea in this article is the presentation of frequency control at
grid side when turbine runs at variable speed. Frequency control has
been done by linear and step variations of the turbine speed. Relation
between turbine speed (frequency) and main grid zero sequence
voltage frequency is presented.
Abstract: This paper is proposed the dynamic simulation of
small power induction motor based on Mathematical modeling. The
dynamic simulation is one of the key steps in the validation of the
design process of the motor drive systems and it is needed for
eliminating inadvertent design mistakes and the resulting error in the
prototype construction and testing. This paper demonstrates the
simulation of steady-state performance of induction motor by
MATLAB Program Three phase 3 hp induction motor is modeled
and simulated with SIMULINK model.
Abstract: In this paper the optimal control strategy for
Permanent Magnet Synchronous Motor (PMSM) based drive system
is presented. The designed full optimal control is available for speed
operating range up to base speed. The optimal voltage space-vector
assures input energy reduction and stator loss minimization,
maintaining the output energy in the same limits with the
conventional PMSM electrical drive. The optimal control with three
components is based on the energetically criteria and it is applicable
in numerical version, being a nonrecursive solution. The simulation
results confirm the increased efficiency of the optimal PMSM drive.
The properties of the optimal voltage space vector are shown.
Abstract: The Wind Turbine Modeling in Wind Energy Conversion System (WECS) using Doubly-Fed Induction Generator (DFIG) PI Controller based design is presented. To study about the variable wind speed. The PI controller performs responding to the dynamic performance. The objective is to study the characteristic of wind turbine and finding the optimum wind speed suitable for wind turbine performance. This system will allow the specification setting (2.5MW). The output active power also corresponding same the input is given. And the reactive power produced by the wind turbine is regulated at 0 Mvar. Variable wind speed is optimum for drive train performance at 12.5 m/s (at maximum power coefficient point) from the simulation of DFIG by Simulink is described.