Abstract: The early-stage damage detection in offshore
structures requires continuous structural health monitoring and for the
large area the position of sensors will also plays an important role in
the efficient damage detection. Determining the dynamic behavior of
offshore structures requires dense deployment of sensors. The wired
Structural Health Monitoring (SHM) systems are highly expensive
and always needs larger installation space to deploy. Wireless sensor
networks can enhance the SHM system by deployment of scalable
sensor network, which consumes lesser space. This paper presents the
results of wireless sensor network based Structural Health Monitoring
method applied to a scaled experimental model of offshore structure
that underwent wave loading. This method determines the
serviceability of the offshore structure which is subjected to various
environment loads. Wired and wireless sensors were installed in the
model and the response of the scaled BLSRP model under wave
loading was recorded. The wireless system discussed in this study is
the Raspberry pi board with Arm V6 processor which is programmed
to transmit the data acquired by the sensor to the server using Wi-Fi
adapter, the data is then hosted in the webpage. The data acquired
from the wireless and wired SHM systems were compared and the
design of the wireless system is verified.
Abstract: Microcantilevers are the basic MEMS devices, which
can be used as sensors, actuators and electronics can be easily built
into them. The detection principle of microcantilever sensors is based
on the measurement of change in cantilever deflection or change in its
resonance frequency. The objective of this work is to explore the
analogies between mechanical and electrical equivalent of
microcantilever beams. Normally scientists and engineers working in
MEMS use expensive software like CoventorWare, IntelliSuite,
ANSYS/Multiphysics etc. This paper indicates the need of developing
electrical equivalent of the MEMS structure and with that, one can
have a better insight on important parameters, and their interrelation of
the MEMS structure. In this work, considering the mechanical model
of microcantilever, equivalent electrical circuit is drawn and using
force-voltage analogy, it is analyzed with circuit simulation software.
By doing so, one can gain access to powerful set of intellectual tools
that have been developed for understanding electrical circuits Later
the analysis is performed using ANSYS/Multiphysics - software based
on finite element method (FEM). It is observed that both mechanical
and electrical domain results for a rectangular microcantlevers are in
agreement with each other.
Abstract: This paper introduces a signal monitoring program
developed with a view to helping electrical engineering students get
familiar with sensors with digital output. Because the output of digital
sensors cannot be simply monitored by a measuring instrument such as
an oscilloscope, students tend to have a hard time dealing with digital
sensors. The monitoring program runs on a PC and communicates with
an MCU that reads the output of digital sensors via an asynchronous
communication interface. Receiving the sensor data from the MCU,
the monitoring program shows time and/or frequency domain plots of
the data in real time. In addition, the monitoring program provides a
serial terminal that enables the user to exchange text information with
the MCU while the received data is plotted. The user can easily
observe the output of digital sensors and configure the digital sensors
in real time, which helps students who do not have enough experiences
with digital sensors. Though the monitoring program was programmed
in the Matlab programming language, it runs without the Matlab since
it was compiled as a standalone executable.
Abstract: To decrease the grating scale thermal expansion error,
a novel method which based on multiple temperature detection is
proposed. Several temperature sensors are installed on the grating
scale and the temperatures of these sensors are recorded. The
temperatures of every point on the grating scale are calculated by
interpolating between adjacent sensors. According to the thermal
expansion principle, the grating scale thermal expansion error model
can be established by doing the integral for the variations of position
and temperature. A novel compensation method is proposed in this
paper. By applying the established error model, the grating scale
thermal expansion error is decreased by 90% compared with no
compensation. The residual positioning error of the grating scale is
less than 15μm/10m and the accuracy of the machine tool is
significant improved.
Abstract: The Figaro AM-1 sensor module which employs TGS
2600 model gas sensor in air quality assessment was used. The
system was coupled with a microprocessor that enables sensor
module to create warning message via telephone. This low cot sensor
system’s performance was compared with a DiagNose II commercial
electronic nose system. Both air quality sensor and electronic nose
system employ metal oxide chemical gas sensors. In the study
experimental setup, data acquisition methods for electronic nose
system, and performance of the low cost air quality system were
evaluated and explained.
Abstract: Optical biosensors have become a powerful detection
and analysis tool for wide-ranging applications in biomedical research,
pharmaceuticals and environmental monitoring. This study carried out
the computational fluid dynamics (CFD)-based simulations to explore
the dispersion phenomenon in the micro channel of an optical
biosensor. The predicted time sequences of concentration contours
were utilized to better understand the dispersion development occurred
in different geometric shapes of micro channels. The simulation results
showed the surface concentrations at the sensing probe (with the best
performance of a grating coupler) in respect of time to appraise the
dispersion effect and therefore identify the design configurations
resulting in minimum dispersion.
Abstract: Cooperative spectrum sensing is a crucial challenge in
cognitive radio networks. Cooperative sensing can increase the
reliability of spectrum hole detection, optimize sensing time and
reduce delay in cooperative networks. In this paper, an efficient
central capacity optimization algorithm is proposed to minimize
cooperative sensing time in a homogenous sensor network using OR
decision rule subject to the detection and false alarm probabilities
constraints. The evaluation results reveal significant improvement in
the sensing time and normalized capacity of the cognitive sensors.
Abstract: Micro-electromechanical system (MEMS)
accelerometers and gyroscopes are suitable for the inertial navigation
system (INS) of many applications due to low price, small
dimensions and light weight. The main disadvantage in a comparison
with classic sensors is a worse long term stability. The estimation
accuracy is mostly affected by the time-dependent growth of inertial
sensor errors, especially the stochastic errors. In order to eliminate
negative effects of these random errors, they must be accurately
modeled. In this paper, the Allan variance technique will be used in
modeling the stochastic errors of the inertial sensors. By performing
a simple operation on the entire length of data, a characteristic curve
is obtained whose inspection provides a systematic characterization
of various random errors contained in the inertial-sensor output data.
Abstract: An experimental and analytical research on shear
buckling of a comparably large polymer composite I-section is
presented. It is known that shear buckling load of a large span
composite beam is difficult to determine experimentally. In order to
sensitively detect shear buckling of the tested I-section, twenty strain
rosettes and eight displacement sensors were applied and attached on
the web and flange surfaces. The tested specimen was a pultruded
composite beam made of vinylester resin, E-glass, carbon fibers and
micro-fillers. Various coupon tests were performed before the shear
buckling test to obtain fundamental material properties of the Isection.
An asymmetric four-point bending loading scheme was
utilized for the shear test. The loading scheme resulted in a high shear
and almost zero moment condition at the center of the web panel. The
shear buckling load was successfully determined after analyzing the
obtained test data from strain rosettes and displacement sensors. An
analytical approach was also performed to verify the experimental
results and to support the discussed experimental program.
Abstract: Optical radiation emitted from a metal-coated fiber tip apex at liquid-air interface was measured. The intensity of the output radiation was strongly depend on the relative position of the tip to a liquid-air interface and varied with surface fluctuations. This phenomenon permits in-situ real-time investigation of nano-metric vibrations of the liquid surface and provides a basis for development of various origin ultrasensitive vibration detecting sensors. The described method can be used for detection of week seismic vibrations.
Abstract: Adsorption of a boron nitride nanotube (BNNT) was
examined toward ethylacetylene (C4H6) molecule by using density
functional theory (DFT) calculations at the B3LYP/6-31G (d) level,
and it was found that the adsorption energy (Ead) of ethylacetylene
the pristine nanotubes is about -1.60kcal/mol. But when nanotube has
been doped with Si and Al atoms, the adsorption energy of
ethylacetylene molecule was increased. Calculation showed that
when the nanotube is doping by Al, the adsorption energy is about -
24.19kcal/mol and also the amount of HOMO/LUMO energy gap
(Eg) will reduce significantly. Boron nitride nanotube is a suitable
adsorbent for ethylacetylene and can be used in separation processes
ethylacetylene. It is seem that nanotube (BNNT) is a suitable
semiconductor after doping, and the doped BNNT in the presence of
ethylacetylene an electrical signal is generating directly and therefore
can potentially be used for ethylacetylene sensors.
Abstract: Nanotechnology is the new cyber, according to several major leaders in this field. Just as cyber is entrenched across global society now, nano is poised to be major capabilities enabler of the next decades. Expert members from the National Nanotechnology Initiative (in U.S.) representing government and science disciplines say nano has great significance for the military and the general public. It is predicted that after next 15 years nanotechnology will replace information technology as the most economic technology platform. Nanotechnology has even wider applications than information technology.
Abstract: The measured data obtained from sensors in
continuous monitoring of civil structures are mainly used for modal
identification and damage detection. Therefore, when modal
identification analysis is carried out the quality in the identification of
the modes will highly influence the damage detection results. It is
also widely recognized that the usefulness of the measured data used
for modal identification and damage detection is significantly
influenced by the number and locations of sensors. The objective of
this study is the numerical implementation of two widely known
optimum sensor placement methods in beam-like structures.
Abstract: The wireless communication is one of the widely used methods of data transfer at the present days. The benefit of this communication method is the partial independence of the infrastructure and the possibility of mobility. In some special applications it is the only way how to connect. This paper presents some problems in the implementation of a sensor network connection for measuring environmental parameters in the area of manufacturing plants.
Abstract: We propose an unconstrained measurement system for scratching motion based on mathematical model of unconstrained bed sensing method which could measure the bed vibrations due to the motion of the person on the bed. In this paper, we construct mathematical model of the unconstrained bed monitoring system; and we apply the unconstrained bed sensing method to the system for detecting scratching motion. The proposed sensors are placed under the three bed feet. When the person is lying on the bed, the output signals from the sensors are proportional to the magnitude of the vibration due to the scratching motion. Hence, we could detect the subject’s scratching motion from the output signals from ceramic sensors. We evaluated two scratching motions using the proposed system in the validity experiment as follows: 1st experiment is the subject’s scratching the right side cheek with his right hand, and; 2nd experiment is the subject’s scratching the shin with another foot. As the results of the experiment, we recognized the scratching signals that enable the determination when the scratching occurred. Furthermore, the difference among the amplitudes of the output signals enabled us to estimate where the subject scratched.
Abstract: This paper presents a predictive model of sensor readings for mobile robot. The model predicts sensor readings for given time horizon based on current sensor readings and velocities of wheels assumed for this horizon. Similar models for such anticipation have been proposed in the literature. The novelty of the model presented in the paper comes from the fact that its structure takes into account physical phenomena and is not just a black box, for example a neural network. From this point of view it may be regarded as a semi-phenomenological model. The model is developed for the Khepera robot, but after certain modifications, it may be applied for any robot with distance sensors such as infrared or ultrasonic sensors.
Abstract: This paper presents a resonant-based read-out circuit for capacitive pressure sensors. The proposed read-out circuit consists of an LC oscillator and a counter. The circuit detects the capacitance changes of a capacitive pressure sensor by means of frequency shifts from its nominal operation frequency. The proposed circuit is designed in 0.18 m CMOS with an estimated power consumption of 43.1mW. Simulation results show that the circuit has a capacitive resolution of 8.06kHz/fF, which enables it for high resolution pressure detection.
Abstract: An acoustic emission (AE) technique is useful for
detection of partial discharges (PDs) at a joint and a terminal section of
a cross-linked polyethylene (XLPE) cable. For AE technique, it is not
difficult to detect a PD using AE sensors. However, it is difficult to
grasp whether the detected AE signal is owing to a single discharge or
not. Additionally, when an AE technique is applied at a terminal
section of a XLPE cable in salt pollution district, for example, there is
possibility of detection of AE signals owing to creeping discharges on
the surface of electric power apparatus. In this study, we evaluated AE
signals in order to grasp what kind of information we can get from
detected AE signals. The results showed that envelop detection of AE
signal and a period which some AE signals were continuously detected
were good indexes for estimating state-of-discharge.
Abstract: This paper presents a new method for read out of the piezoresistive accelerometer sensors. The circuit works based on Instrumentation amplifier and it is useful for reducing offset In Wheatstone Bridge. The obtained gain is 645 with 1μv/°c Equivalent drift and 1.58mw power consumption. A Schmitt trigger and multiplexer circuit control output node. a high speed counter is designed in this work .the proposed circuit is designed and simulated In 0.18μm CMOS technology with 1.8v power supply.
Abstract: This article presents a computationally tractable probabilistic model for the relation between the complex wavelet coefficients of two images of the same scene. The two images are acquisitioned at distinct moments of times, or from distinct viewpoints, or by distinct sensors. By means of the introduced probabilistic model, we argue that the similarity between the two images is controlled not by the values of the wavelet coefficients, which can be altered by many factors, but by the nature of the wavelet coefficients, that we model with the help of hidden state variables. We integrate this probabilistic framework in the construction of a new image registration algorithm. This algorithm has sub-pixel accuracy and is robust to noise and to other variations like local illumination changes. We present the performance of our algorithm on various image types.