Abstract: In recent years various types of electric vehicles
has gained again increasing attention as an environmentally
benign technology in transport. Especially for urban areas with
high local pollution this Zero-emission technology (at the point
of use) is considered to provide proper solutions. Yet, the bad
economics and the limited driving ranges are still major barriers
for a broader market penetration of battery electric vehicles
(BEV) and of fuel cell vehicles (FCV). The major result of our
analyses is that the most important precondition for a further
dissemination of BEV in urban areas are emission-free zones.
This is an instrument which allows the promotion of BEV
without providing excessive subsidies. In addition, it is
important to note that the full benefits of EV can only be
harvested if the electricity used is produced from renewable
energy sources. That is to say, it has to be ensured that the use of
BEV in urban areas is clearly linked to a green electricity
purchase model. And moreover, the introduction of a CO2-
emission-based tax system would support this requirement.
Abstract: Renewable water resources are crucial production
variables in arid and semi-arid regions where intensive agriculture is
practiced to meet ever-increasing demand for food and fiber. This is
crucial for the Dez and Moghan command areas where water delivery
problems and adverse environmental issues are widespread. This
paper aims to identify major problems areas using on-farm surveys of
200 farmers, agricultural extensionists and water suppliers which was
complemented by secondary data and field observations during 2010-
2011 cultivating season. The SPSS package was used to analyze and
synthesis data. Results indicated inappropriate canal operations in
both schemes, though there was no unanimity about the underlying
causes. Inequitable and inflexible distribution was found to be rooted
in deficient hydraulic structures particularly in the main and
secondary canals. The inadequacy and inflexibility of water
scheduling regime was the underlying causes of recurring pest and
disease spread which often led to the decline of crop yield and
quality, although these were not disputed, the water suppliers were
not prepared to link with the deficiencies in the operation of the main
and secondary canals. They rather attributed these to the prevailing
salinity; alkalinity, water table fluctuations and leaching of the
valuable agro-chemical inputs from the plants- route zone with farreaching
consequences. Examples of these include the pollution of
ground and surface resources due to over-irrigation at the farm level
which falls under the growers- own responsibility. Poor irrigation
efficiency and adverse environmental problems were attributed to
deficient and outdated farming practices that were in turn rooted in
poor extension programs and irrational water charges.
Abstract: There is a great deal of interest in constructing Double Skin Facade (DSF) structures which are considered as modern movement in field of Energy Conservation, renewable energies, and Architecture design. This trend provides many conclusive alternatives which are frequently associated with sustainable building. In this paper a building with Double Skin Facade is considered in the semiarid climate of Tehran, Iran, in order to consider the DSF-s performance during hot seasons. Mathematical formulations calculate solar heat gain by the external skin. Moreover, Computational Fluid Dynamics (CFD) simulations were performed on the case study building to enhance effectiveness of the facade. The conclusion divulged difference of gained energy by the cavity and room with and without blind and louvers. Some solutions were introduced to surge the performance of natural ventilation by plunging the cooling loads in summer.
Abstract: Solar energy has a major role in renewable energy
resources. Solar Cell as a basement of solar system has attracted lots
of research. To conduct a study about solar energy system, an
authenticated model is required. Diode base PV models are widely
used by researchers. These models are classified based on the number
of diodes used in them. Single and two-diode models are well
studied. Single-diode models may have two, three or four elements.
In this study, these solar cell models are examined and the simulation
results are compared to each other. All PV models are re-designed in
the Matlab/Simulink software and they examined by certain test
conditions and parameters. This paper provides comparative studies
of these models and it tries to compare the simulation results with
manufacturer-s data sheet to investigate model validity and accuracy.
The results show a four- element single-diode model is accurate and
has moderate complexity in contrast to the two-diode model with
higher complexity and accuracy
Abstract: The objective of this research is to study the technical
and economic performance of wind/diesel/battery (W/D/B) system
supplying a remote small gathering of six families using HOMER
software package. The electrical energy is to cater for the basic needs
for which the daily load pattern is estimated. Net Present Cost (NPC)
and Cost of Energy (COE) are used as economic criteria, while the measure of performance is % of power shortage. Technical and
economic parameters are defined to estimate the feasibility of the
system under study. Optimum system configurations are estimated for two sites. Using HOMER software, the simulation results showed that W/D/B systems are economical for the assumed community sites
as the price of generated electricity is about 0.308 $/kWh, without
taking external benefits into considerations. W/D/B systems are more
economical than W/B or diesel alone systems, as the COE is 0.86 $/kWh for W/B and 0.357 $/kWh for diesel alone.
Abstract: A model is presented to find the optimal design of the
mixed renewable warranty policy for non-repairable Weibull life
products. The optimal design considers the conflict of interests
between the customer and the manufacturer: the customer interests
are longer full rebate coverage period and longer total warranty
coverage period, the manufacturer interests are lower warranty cost
and lower risk. The design factors are full rebate and total warranty
coverage periods. Results showed that mixed policy is better than full
rebate policy in terms of risk and total warranty coverage period in all
of the three bathtub regions. In addition, results showed that linear
policy is better than mixed policy in infant mortality and constant
failure regions while the mixed policy is better than linear policy in
ageing region of the model. Furthermore, the results showed that
using burn-in period for infant mortality products reduces warranty
cost and risk.
Abstract: The increasing industrialization and motorization of the world has led to a steep rise for the demand of petroleum-based fuels. Petroleum-based fuels are obtained from limited reserves. These finite reserves are highly concentrated in certain regions of the world. Therefore, those countries not having these resources are facing energy/foreign exchange crisis, mainly due to the import of crude petroleum. Hence, it is necessary to look for alternative fuels which can be produced from resources available locally within the country such as alcohol, biodiesel, vegetable oils etc. Biodiesel is a renewable, domestically produced fuel that has been shown to reduce particulate, hydrocarbon, and carbon monoxide emissions from combustion. In the present study an experimental investigation on emission characteristic of a liquid burner system operating on several percentage of biodiesel and gas oil is carried out. Samples of exhaust gas are analysed with Testo 350 Xl. The results show that biodiesel can lower some pollutant such as CO, CO2 and particulate matter emissions while NOx emission would increase in comparison with gas oil. The results indicate there may be benefits to using biodiesel in industrial processes.
Abstract: Biomass is becoming a large renewable resource for
power generation; it is involved in higher frequency in
environmentally clean processes, and even it is used for biofuels
preparation. On the other hand, hydrogen – other energy source – can
be produced in a variety of methods including gasification of
biomass. In this study, the production of hydrogen by gasification of
biomass waste is examined. This work explores the production of a
gaseous mixture with high power potential from Amazonas´ specie
known as copoazu, using a counter-flow fixed-bed bioreactor.
Abstract: The development of renewable energies - particularly energy from wind, water, solar power and biomass - is a central aim of the European Commission's energy policy. There are several reasons for this choice: renewable energies are sustainable, nonpolluting, widely available and clean. Increasing the share of renewable energy in the energy balance enhances sustainability. It also helps to improve the security of energy supply by reducing the Community's growing dependence on imported energy sources.In this paper it was studied the possibility to realize three photovoltaic systems in the Italian Natural Park “Gola della Rossa e di Frasassi". The first photovoltaic system is a grid-connected system for Services and Documentation Center of Castelletta with a nominal power of about 6 kWp. The second photovoltaic system is a grid-connected integrated system on the ticket office-s roof with a nominal power of about 4 kWp. The third project is set up by five grid-connected systems integrated on the roofs of the bungalows in Natural Park-s tourist camping with a nominal power of about 10 kWp. The electricity which is generated by all these plants is purchased according to the Italian program called “Conto Energia". Economical analysis and the amount of the avoided CO2 emissions are elaborated for these photovoltaic systems.
Abstract: Biofuels, like biobutanol, have been recognized for
being renewable and sustainable fuels which can be produced from
lignocellulosic biomass. To convert lignocellulosic biomass to
biofuel, pretreatment process is an important step to remove
hemicelluloses and lignin to improve enzymatic hydrolysis. Dilute
acid pretreatment has been successful developed for pretreatment of
corncobs and the optimum conditions of dilute sulfuric and
phosphoric acid pretreatment were obtained at 120 °C for 5 min with
15:1 liquid to solid ratio and 140 °C for 10 min with 10:1 liquid to
solid ratio, respectively. The result shows that both of acid
pretreatments gave the content of total sugar approximately 34–35
g/l. In case of inhibitor content (furfural), phosphoric acid
pretreatment gives higher than sulfuric acid pretreatment.
Characterizations of corncobs after pretreatment indicate that both of
acid pretreatments can improve enzymatic accessibility and the better
results present in corncobs pretreated with sulfuric acid in term of
surface area, crystallinity, and composition analysis.
Abstract: Since the 80s huge efforts have been made to utilize
renewable energy sources to generate electric power. This paper
reports some aspects of integration of the distributed generators into
the low voltage distribution networks. An assessment of impact of the
distributed generators on the reliability indices of low voltage
network is performed. Results obtained from case study using low
voltage network, are presented and discussed.
Abstract: The utilization of renewable energy sources in electric
power systems is increasing quickly because of public apprehensions
for unpleasant environmental impacts and increase in the energy
costs involved with the use of conventional energy sources. Despite
the application of these energy sources can considerably diminish the
system fuel costs, they can also have significant influence on the
system reliability. Therefore an appropriate combination of the
system reliability indices level and capital investment costs of system
is vital. This paper presents a hybrid wind/photovoltaic plant, with
the aim of supplying IEEE reliability test system load pattern while
the plant capital investment costs is minimized by applying a hybrid
particle swarm optimization (PSO) / harmony search (HS) approach,
and the system fulfills the appropriate level of reliability.
Abstract: Hydrogen that used as fuel in fuel cell vehicles can be
produced from renewable sources such as wind, solar, and hydro
technologies. PV-electrolyzer is one of the promising methods to
produce hydrogen with zero pollution emission. Hydrogen
production from a PV-electrolyzer system depends on the efficiency
of the electrolyzer and photovoltaic array, and sun irradiance at that
site. In this study, the amount of hydrogen is obtained using
mathematical equations for difference driving distance and sun peak
hours. The results show that the minimum of 99 PV modules are used
to generate 1.75 kgH2 per day for two vehicles.
Abstract: Lignocellulosic materials are considered the most
abundant renewable resource available for the Bioethanol
Production. Water Hyacinth is one of potential raw material of the
world-s worst aquatic plant as a feedstock to produce Bioethanol.
The purposed this research is obtain reduced of matter for
biodegradation lignin in Biological pretreatment with White Rot
Fungi eg. Phanerochaete Chrysosporium using Solid state
Fermentation methods. Phanerochaete Chrysosporium is known to
have the best ability to degraded lignin, but simultaneously it can also
degraded cellulose and hemicelulose. During 8 weeks incubation,
water hyacinth occurred loss of weight reached 34,67%, while loss
of lignin reached 67,21%, loss of cellulose reached 11,01% and loss
of hemicellulose reached 36,56%. The kinetic of losses lignin using
regression linear plot, the results is obtained constant rate (k) of
reduction lignin is -0.1053 and the equation of reduction of lignin
is y = wo - 0, 1.53 x
Abstract: In this paper, we present a technical and an economic
assessment of several sources of renewable energy in Saudi Arabia;
mainly solar, wind, hydro and biomass. We analyze the
environmental and climatic conditions in relation to these sources
and give an overview of some of the existing clean energy
technologies. Using standardized cost and efficiency data, we carry
out a cost benefit analysis to understand the economic factors
influencing the sustainability of energy production from renewable
sources in light of the energy cost and demand in the Saudi market.
Finally, we take a look at the Saudi petroleum industry and the
existing sources of conventional energy and assess the potential of
building a successful market for renewable energy under the
constraints imposed by the flow of subsidized cheap oil. We show
that while some renewable energy resources are well suited for
distributed or grid connected generation in the kingdom, their
viability is greatly undercut by the well developed and well
capitalized oil industry.
Abstract: The paper presents the results of the European EIE
project “Realising the potential for small scale renewable energy
sources in the home – Kyotointhehome". The project's global aim is
to inform and educate teachers, students and their families so that
they can realise the need and can assess the potential for energy
efficiency (EE) measures and renewable energy sources (RES) in
their homes. The project resources were translated and trialled by 16
partners in 10 European countries.
A web-based methodology which will enable families to assess
how RES can be incorporated into energy efficient homes was
accomplished. The web application “KYOTOINHOME" will help
the citizens to identify what they can do to help their community
meet the Kyoto target for greenhouse gas reductions and prevent
global warming. This application provides useful information on how
the citizens can use renewable energy sources in their home to
provide space heating and cooling, hot water and electricity. A
methodology for assessing heat loss in a dwelling and application of
heat pump system was elaborated and will be implemented this year.
For schools, we developed a set of practical activities concerned with
preventing climate change through using renewable energy sources.
Complementary resources will also developed in the Romanian
research project “Romania Contribution to the European Targets
Regarding the Development of Renewable Energy Sources" -
PROMES.
Abstract: Polymers are one of the most widely used materials in our every day life. The subject of renewable resources has attracted great attention in the last period of time. New polymeric materials derived from renewable resources, like carbohydrates draw attention to public eye especially because of their biocompatibility and biodegradability. The aim of our paper was to obtain environmentally compatible polymers from monosaccharides. Novel glycopolymers based on D-glucose have been obtained from copolymerization of a new monomer carrying carbohydrate moiety with methyl methacrylate (MMA) via free radical bulk polymerization. Differential scanning calorimetry (DSC) was performed in order to study the copolymerization process of the monomer into the chosen co-monomer; the activation energy of this process was evaluated using Ozawa method. The copolymers obtained were characterized using ATR-FTIR spectroscopy. The thermal stability of the obtained products was studied by thermogravimetry (TG).
Abstract: With the growth of modern civilization and
industrialization in worldwide, the demand for energy is increasing
day by day. Majority of the world-s energy needs are met through
fossil fuels and natural gas. As a result the amount of fossil fuels is
on diminishing from year to year. Since the fossil fuel is nonrenewable,
so fuel price is gouging as a consequence of spiraling
demand and diminishing supply. At present the power generation of
our country is mainly depends on imported fossil fuels. To reduce the
dependency on imported fuel, the use of renewable sources has
become more popular. In Bangladesh coconut is widely growing tree.
Especially in the southern part of the country a large area will be
found where coconut tree is considered as natural asset. So, our
endeavor was to use the coconut oil as a renewable and alternative
fuel. This article shows the prospect of coconut oil as a renewable
and alternative fuel of diesel fuel. Since diesel engine has a versatile
uses including small electricity generation, an experimental set up is
then made to study the performance of a small diesel engine using
different blends of bio diesel converted from coconut oil. It is found
that bio diesel has slightly different properties than diesel. With
biodiesel the engine is capable of running without difficulty.
Different blends of bio diesel (i.e. B80, B60, and B 50 etc.) have
been used to avoid complicated modification of the engine or the fuel
supply system. Finally, a comparison of engine performance for
different blends of biodiesel has been carried out to determine the
optimum blend for different operating conditions.
Abstract: This paper presents a developed method for
controlling multi-renewable energy generators. The control system
depends basically on three sensors (wind anemometer, solar sensor,
and voltage sensor). These sensors represent PLC-s analogue inputs.
Controlling the output voltage supply can be achieved by an
enhanced method of interlocking between the renewable energy
generators, depending on those sensors and output contactors.
Abstract: The paper aims to show that implementing different
types of reflectors in solar energy systems, will dramatically improve
energy production by means of concentrating and intensifying more
sunlight onto a solar cell. The Solar Intensifier unit is designed to
increase efficiency and performance of a set of solar panels. The unit
was fabricated and tested. The experimental results show good
improvement in the performance of the solar energy system.