Abstract: The paper presents a modelling methodology for
small scale multi-source renewable energy systems. Using historical
site-specific weather data, the relationships of cost, availability and
energy form are visualised as a function of the sizing of photovoltaic
arrays, wind turbines, and battery capacity. The specific dependency
of each site on its own particular weather patterns show that unique
solutions exist for each site. It is shown that in certain cases the
capital component cost can be halved if the desired theoretical
demand availability is reduced from 100% to 99%.
Abstract: Renewable energy resources are inexhaustible, clean as compared with conventional resources. Also, it is used to supply regions with no grid, no telephone lines, and often with difficult accessibility by common transport. Satellite earth stations which located in remote areas are the most important application of renewable energy. Neural control is a branch of the general field of intelligent control, which is based on the concept of artificial intelligence. This paper presents the mathematical modeling of satellite earth station power system which is required for simulating the system.Aswan is selected to be the site under consideration because it is a rich region with solar energy. The complete power system is simulated using MATLAB–SIMULINK.An artificial neural network (ANN) based model has been developed for the optimum operation of earth station power system. An ANN is trained using a back propagation with Levenberg–Marquardt algorithm. The best validation performance is obtained for minimum mean square error. The regression between the network output and the corresponding target is equal to 96% which means a high accuracy. Neural network controller architecture gives satisfactory results with small number of neurons, hence better in terms of memory and time are required for NNC implementation. The results indicate that the proposed control unit using ANN can be successfully used for controlling the satellite earth station power system.
Abstract: Alternative energy is any energy source that is an alternative to fossil fuel. These alternatives are intended to address concerns about such fossil fuels. Today, because of the variety of energy choices and differing goals of their advocates, defining some energy types as "alternative" is highly controversial. Most of the recent and existing alternative sources of energy are discussed below
Abstract: Decision support based upon risk analysis into
comparison of the electricity generation from different renewable
energy technologies can provide information about their effects on
the environment and society. The aim of this paper is to develop the
assessment framework regarding risks to health and environment,
and the society-s benefits of the electric power plant generation from
different renewable sources. The multicriteria framework to
multiattribute risk analysis technique and the decision analysis
interview technique are applied in order to support the decisionmaking
process for the implementing renewable energy projects to
the Bangkok case study. Having analyses the local conditions and
appropriate technologies, five renewable power plants are postulated
as options. As this work demonstrates, the analysis can provide a tool
to aid decision-makers for achieving targets related to promote
sustainable energy system.
Abstract: Wind energy has been shown to be one of the most
viable sources of renewable energy. With current technology, the low
cost of wind energy is competitive with more conventional sources of
energy such as coal. Most blades available for commercial grade
wind turbines incorporate a straight span-wise profile and airfoil
shaped cross sections. These blades are found to be very efficient at
lower wind speeds in comparison to the potential energy that can be
extracted. However as the oncoming wind speed increases the
efficiency of the blades decreases as they approach a stall point. This
paper explores the possibility of increasing the efficiency of the
blades at higher wind speeds while maintaining efficiency at the
lower wind speeds. The design intends to maintain efficiency at
lower wind speeds by selecting the appropriate orientation and size
of the airfoil cross sections based on a low oncoming wind speed and
given constant rotation rate. The blades will be made more efficient
at higher wind speeds by implementing a swept blade profile.
Performance was investigated using the computational fluid
dynamics (CFD).
Abstract: This paper focuses on developing an integrated
reliable and sophisticated model for ultra large wind turbines And to
study the performance and analysis of vector control on large wind
turbines. With the advance of power electronics technology, direct
driven multi-pole radial flux PMSG (Permanent Magnet Synchronous
Generator) has proven to be a good choice for wind turbines
manufacturers. To study the wind energy conversion systems, it is
important to develop a wind turbine simulator that is able to produce
realistic and validated conditions that occur in real ultra MW wind
turbines. Three different packages are used to simulate this model,
namely, Turbsim, FAST and Simulink. Turbsim is a Full field wind
simulator developed by National Renewable Energy Laboratory
(NREL). The wind turbine mechanical parts are modeled by FAST
(Fatigue, Aerodynamics, Structures and Turbulence) code which is
also developed by NREL. Simulink is used to model the PMSG, full
scale back to back IGBT converters, and the grid.
Abstract: Food and fibre production in arid and semi-arid regions has emerged as one of the major challenges for various socio-economic and political reasons such as the food security and self-sufficiency. Productive use of the renewable water resources has risen on top ofthe decision-making agenda. For this reason, efficient operation and maintenance of modern irrigation and drainage schemes become part and parcel and indispensible reality in agricultural policy making arena. The aim of this paper is to investigate the complexity of operating and maintaining such schemes, mainly focussing on challenges which enhance and opportunities that impedsustainable food and fibre production. The methodology involved using secondary data complemented byroutine observations and stakeholders views on issues that influence the O&M in the Dez command area. The SPSS program was used as an analytical framework for data analysis and interpretation.Results indicate poor application efficiency in most croplands, much of which is attributed to deficient operation of conveyance and distribution canals. These in turn, are reportedly linked to inadequate maintenance of the pumping stations and hydraulic structures like turnouts,flumes and other control systems particularly in the secondary and tertiary canals. Results show that the aforementioned deficiencies have been the major impediment to establishing regular flow toward the farm gates which subsequently undermine application efficiency and tillage operationsat farm level. Results further show that accumulative impact of such deficiencies has been the major causes of poorcrop yield and quality that deem production system in these croplands uneconomic. Results further show that the present state might undermine the sustainability of agricultural system in the command area. The overall conclusion being that present water management is unlikely to be responsive to challenges that the sector faces. And in the absence of coherent measures to shift the status quo situation in favour of more productive resource use, it would be hard to fulfil the objectives of the National Economic and Socio-cultural Development Plans.
Abstract: The development and application of wind power for
renewable energy has attracted growing interest in recent years. Renewable energy sources are attracting much alteration as they can
reduce both environmental damage and dependence on fossil fuels. With the growing need for sustainable energy supplies, a case is made
for decentralized, stand-alone power supplies (SAPS) as an alternative to power grids. In the era which traditional petroleum energy resource
decreasing and the green house affect significant increasing, the development and usage of regenerative resources is inevitable. Due to the contribution of the pioneers, the development of regenerative resources already has a remarkable achievement; however, in the view of economy and quantity, it is still a long road for regenerative energy
to replace traditional petroleum energy. In our prospective, in stead of
investigate larger regenerative energy equipment, it is much wiser to
think about the blind side and breakthrough of the current technique.
Abstract: Biogas, a clean renewable energy, is attracting a growing
concern of researchers and professionals in many fields. Based
on the natural and climatic conditions in semi-arid regions of northwestern
China, the present study introduces a specifically-designed
family-size biogas plant (with a digester of 10m3) with manure
and urine of animals and humanity as raw materials. The biogas
plant is applicable to areas with altitudes of more than 2000 meters
in northwestern China. In addition to the installation cost, a little
operational expenditure, structure, characteristics, benefits of this
small-scale biogas plant, this article introduces a wide range of
specific popularization methods such as training, financial support,
guided tour to the biogas plant, community-based group study and
delivery of operational manuals. The feasibility of the biogas plant is
explored on the basis of the availability of the raw materials. Simple
operations contained in the current work increase the possibility of
the wide use of this small-scale biogas plant in similar regions of the
world.
Abstract: Nowadays, the focus on renewable energy and alternative fuels has increased due to increasing oil prices, environment pollution, and also concern on preserving the nature. Biodiesel has been known as an attractive alternative fuel although biodiesel produced from edible oil is very expensive than conventional diesel. Therefore, the uses of biodiesel produced from non-edible oils are much better option. Currently Jatropha biodiesel (JBD) is receiving attention as an alternative fuel for diesel engine. Biodiesel is non-toxic, biodegradable, high lubricant ability, highly renewable, and its use therefore produces real reduction in petroleum consumption and carbon dioxide (CO2) emissions. Although biodiesel has many advantages, but it still has several properties need to improve, such as lower calorific value, lower effective engine power, higher emission of nitrogen oxides (NOX) and greater sensitivity to low temperature. Exhaust gas recirculation (EGR) is effective technique to reduce NOX emission from diesel engines because it enables lower flame temperature and oxygen concentration in the combustion chamber. Some studies succeeded to reduce the NOX emission from biodiesel by EGR but they observed increasing soot emission. The aim of this study was to investigate the engine performance and soot emission by using blended Jatropha biodiesel with different EGR rates. A CI engine that is water-cooled, turbocharged, using indirect injection system was used for the investigation. Soot emission, NOX, CO2, carbon monoxide (CO) were recorded and various engine performance parameters were also evaluated.
Abstract: In this work, an attempt is made to design an optimal
wind/pv/diesel hybrid power system for a village of Ain Merane,
Chlef, Algeria, where the wind speed and solar radiation
measurements were made. The aim of this paper is the optimization
of a hybrid wind/solar/diesel system applied in term of technical and
economic feasibility by simulation using HOMER. A comparison
was made between the performance of wind/pv/diesel system and the
classic connecting system.
Abstract: Optimal load shedding (LS) design as an emergency plan is one of the main control challenges posed by emerging new uncertainties and numerous distributed generators including renewable energy sources in a modern power system. This paper presents an overview of the key issues and new challenges on optimal LS synthesis concerning the integration of wind turbine units into the power systems. Following a brief survey on the existing LS methods, the impact of power fluctuation produced by wind powers on system frequency and voltage performance is presented. The most LS schemas proposed so far used voltage or frequency parameter via under-frequency or under-voltage LS schemes. Here, the necessity of considering both voltage and frequency indices to achieve a more effective and comprehensive LS strategy is emphasized. Then it is clarified that this problem will be more dominated in the presence of wind turbines.
Abstract: In a world of climate change and limited fossil fuel resources, renewable energy sources are playing an increasingly important role. Due to industrializations and population growth our economy and technologies today largely depend upon natural resources, which are not replaceable. Approximately 90% of our energy consumption comes from fossil fuels (viz. coal, oil and natural gas). The irony is that these resources are depleting. Also, the huge consumption of fossil fuels has caused visible damage to the environment in various forms viz. global warming, acid rains etc.
Abstract: The utilization of cheese whey as a fermentation
substrate to produce bio-ethanol is an effort to supply bio-ethanol
demand as a renewable energy. Like other process systems, modeling
is also required for fermentation process design, optimization and
plant operation. This research aims to study the fermentation process
of cheese whey by applying mathematics and fundamental concept in
chemical engineering, and to investigate the characteristic of the
cheese whey fermentation process. Steady state simulation results for
inlet substrate concentration of 50, 100 and 150 g/l, and various
values of hydraulic retention time, showed that the ethanol
productivity maximum values were 0.1091, 0.3163 and 0.5639 g/l.h
respectively. Those values were achieved at hydraulic retention time
of 20 hours, which was the minimum value used in this modeling.
This showed that operating reactor at low hydraulic retention time
was favorable. Model of bio-ethanol production from cheese whey
will enhance the understanding of what really happen in the
fermentation process.
Abstract: The utilize of renewable energy sources becomes
more crucial and fascinatingly, wider application of renewable
energy devices at domestic, commercial and industrial levels is not
only affect to stronger awareness but also significantly installed
capacities. Moreover, biomass principally is in form of woods and
converts to be energy for using by humans for a long time.
Gasification is a process of conversion of solid carbonaceous fuel
into combustible gas by partial combustion. Many gasified models
have various operating conditions because the parameters kept in
each model are differentiated. This study applied the experimental
data including three inputs variables including biomass consumption;
temperature at combustion zone and ash discharge rate and gas flow
rate as only one output variable. In this paper, response surface
methods were applied for identification of the gasified system
equation suitable for experimental data. The result showed that linear
model gave superlative results.
Abstract: Nowadays there are several grid connected converter
in the grid system. These grid connected converters are generally the
converters of renewable energy sources, industrial four quadrant
drives and other converters with DC link. These converters are
connected to the grid through a three phase bridge. The standards
prescribe the maximal harmonic emission which could be easily
limited with high switching frequency. The increased switching
losses can be reduced to the half with the utilization of the wellknown
Flat-top modulation. The suggested control method is the
expansion of the Flat-top modulation with which the losses could be
also reduced to the half compared to the Flat-top modulation.
Comparing to traditional control these requirements can be
simultaneously satisfied much better with the DLF (DC Link
Floating) method.
Abstract: A hybrid Photovoltaic/Thermal (PV/T) solar system integrates photovoltaic and solar thermal technologies into one single solar energy device, with dual generation of electricity and heat energy. The aim of the present study is to evaluate the potential for introduction of the PV/T technology into Northern China. For this purpose, outdoor experiments were conducted on a prototype of a PV/T water-heating system. The annual thermal and electrical performances were investigated under the climatic conditions of Beijing. An economic analysis of the system was then carried out, followed by a sensitivity study. The analysis revealed that the hybrid system is not economically attractive with the current market and energy prices. However, considering the continuous commitment of the Chinese government towards policy development in the renewable energy sector, and technological improvements like the increasing cost-effectiveness of PV cells, PV/Thermal technology may become economically viable in the near future.
Abstract: Photovoltaic power generation forecasting is an
important task in renewable energy power system planning and
operating. This paper explores the application of neural networks
(NN) to study the design of photovoltaic power generation
forecasting systems for one week ahead using weather databases
include the global irradiance, and temperature of Ghardaia city
(south of Algeria) using a data acquisition system. Simulations were
run and the results are discussed showing that neural networks
Technique is capable to decrease the photovoltaic power generation
forecasting error.
Abstract: A ten-year grazing study was conducted at the
Agriculture and Agri-Food Canada Brandon Research Centre in
Manitoba to study the effect of alfalfa inclusion and fertilizer (N, P,
K, and S) addition on economics and efficiency of non-renewable
energy use in meadow brome grass-based pasture systems for beef
production. Fertilizing grass-only or alfalfa-grass pastures to full soil
test recommendations improved pasture productivity, but did not
improve profitability compared to unfertilized pastures. Fertilizing
grass-only pastures resulted in the highest net loss of any pasture
management strategy in this study. Adding alfalfa at the time of
seeding, with no added fertilizer, was economically the best pasture
improvement strategy in this study. Because of moisture limitations,
adding commercial fertilizer to full soil test recommendations is
probably not economically justifiable in most years, especially with
the rising cost of fertilizer. Improving grass-only pastures by adding
fertilizer and/or alfalfa required additional non-renewable energy
inputs; however, the additional energy required for unfertilized
alfalfa-grass pastures was minimal compared to the fertilized
pastures. Of the four pasture management strategies, adding alfalfa
to grass pastures without adding fertilizer had the highest efficiency
of energy use. Based on energy use and economic performance, the
unfertilized alfalfa-grass pasture was the most efficient and
sustainable pasture system.
Abstract: Project managers are the ultimate responsible for the
overall characteristics of a project, i.e. they should deliver the project
on time with minimum cost and with maximum quality. It is vital for
any manager to decide a trade-off between these conflicting
objectives and they will be benefited of any scientific decision
support tool. Our work will try to determine optimal solutions (rather
than a single optimal solution) from which the project manager will
select his desirable choice to run the project. In this paper, the
problem in project scheduling notated as
(1,T|cpm,disc,mu|curve:quality,time,cost) will be studied. The
problem is multi-objective and the purpose is finding the Pareto
optimal front of time, cost and quality of a project
(curve:quality,time,cost), whose activities belong to a start to finish
activity relationship network (cpm) and they can be done in different
possible modes (mu) which are non-continuous or discrete (disc), and
each mode has a different cost, time and quality . The project is
constrained to a non-renewable resource i.e. money (1,T). Because
the problem is NP-Hard, to solve the problem, a meta-heuristic is
developed based on a version of genetic algorithm specially adapted
to solve multi-objective problems namely FastPGA. A sample project
with 30 activities is generated and then solved by the proposed
method.