Abstract: The work presented in this study is related to an
energy system analysis based on passive cooling system for
dwellings. It consists to solar chimney energy performances
determination versus geometrical and environmental considerations
as the size and inlet width conditions of the chimney. Adrar site
located in the southern region of Algeria is chosen for this study
according to ambient temperature and solar irradiance technical data
availability. Obtained results are related to the glazing temperature
distributions, the chimney air flow and internal wall temperatures.
The air room change per hour (ACH) parameter, the outlet air
velocity and mass air flow rate are also determined. It is shown that
the chimney width has a significant effect on energy performances
compared to its entry size. A good agreement is observed between
these results and those obtained by others from the literature.
Abstract: This paper describes Independent Component Analysis (ICA) based fixed-point algorithm for the blind separation of the convolutive mixture of speech, picked-up by a linear microphone array. The proposed algorithm extracts independent sources by non- Gaussianizing the Time-Frequency Series of Speech (TFSS) in a deflationary way. The degree of non-Gaussianization is measured by negentropy. The relative performances of algorithm under random initialization and Null beamformer (NBF) based initialization are studied. It has been found that an NBF based initial value gives speedy convergence as well as better separation performance
Abstract: The aerodynamic performances of vertical axis wind
turbines are highly affected by tip vortexes. In the present
work, different tip devices are considered and simulated against
a baseline rotor configuration, with the aim of identifying the
best tip architecture. Three different configurations are tested:
winglets, an elliptic termination and an aerodynamic bulkhead.
A comparative analysis on the most promising architectures is
conducted, focusing also on blade torque evolution during a full
revolution of the rotor blade. The most promising technology is
concluded to be a well designed winglet.
Abstract: The article deals with pneumatic and hot wire
anemometry measurement on subsonic axi-symmetric air ejector.
Performances of the ejector with and without pulsations of primary
flow are compared, measuring of characteristic pressures and mass
flow rates are performed and ejector efficiency is evaluated. The
pulsations of primary flow are produced by a synthetic jet generator,
which is placed in the supply line of the primary flow just in front of
the primary nozzle. The aim of the pulsation is to intensify the
mixing process. In the article we present: Pressure measuring of
pulsation on the mixing chamber wall, behind the mixing chamber
and behind the diffuser measured by fast pressure transducers and
results of hot wire anemometry measurement. It was found out that
using of primary flow pulsations yields higher back pressure behind
the ejector and higher efficiency. The processes in this ejector and
influences of primary flow pulsations on the mixing processes are
described.
Abstract: This study proposes a multi-response surface
optimization problem (MRSOP) for determining the proper choices
of a process parameter design (PPD) decision problem in a noisy
environment of a grease position process in an electronic industry.
The proposed models attempts to maximize dual process responses
on the mean of parts between failure on left and right processes. The
conventional modified simplex method and its hybridization of the
stochastic operator from the hunting search algorithm are applied to
determine the proper levels of controllable design parameters
affecting the quality performances. A numerical example
demonstrates the feasibility of applying the proposed model to the
PPD problem via two iterative methods. Its advantages are also
discussed. Numerical results demonstrate that the hybridization is
superior to the use of the conventional method. In this study, the
mean of parts between failure on left and right lines improve by
39.51%, approximately. All experimental data presented in this
research have been normalized to disguise actual performance
measures as raw data are considered to be confidential.
Abstract: Drilling is the most common machining operation and it forms the highest machining cost in many manufacturing activities including automotive engine production. The outcome of this operation depends upon many factors including utilization of proper cutting tool geometry, cutting tool material and the type of coating used to improve hardness and resistance to wear, and also cutting parameters. With the availability of a large array of tool geometries, materials and coatings, is has become a challenging task to select the best tool and cutting parameters that would result in the lowest machining cost or highest profit rate. This paper describes an algorithm developed to help achieve good performances in drilling operations by automatically determination of proper cutting tools and cutting parameters. It also helps determine machining sequences resulting in minimum tool changes that would eventually reduce machining time and cost where multiple tools are used.
Abstract: Model Predictive Control (MPC) is increasingly being
proposed for real time applications and embedded systems. However
comparing to PID controller, the implementation of the MPC in
miniaturized devices like Field Programmable Gate Arrays (FPGA)
and microcontrollers has historically been very small scale due to its
complexity in implementation and its computation time requirement.
At the same time, such embedded technologies have become an
enabler for future manufacturing enterprises as well as a transformer
of organizations and markets. Recently, advances in microelectronics
and software allow such technique to be implemented in embedded
systems. In this work, we take advantage of these recent advances
in this area in the deployment of one of the most studied and
applied control technique in the industrial engineering. In fact in
this paper, we propose an efficient framework for implementation
of Generalized Predictive Control (GPC) in the performed STM32
microcontroller. The STM32 keil starter kit based on a JTAG interface
and the STM32 board was used to implement the proposed GPC
firmware. Besides the GPC, the PID anti windup algorithm was
also implemented using Keil development tools designed for ARM
processor-based microcontroller devices and working with C/Cµ
langage. A performances comparison study was done between both
firmwares. This performances study show good execution speed and
low computational burden. These results encourage to develop simple
predictive algorithms to be programmed in industrial standard hardware.
The main features of the proposed framework are illustrated
through two examples and compared with the anti windup PID
controller.
Abstract: Lighting upgrades involve relatively lower costs which
allow the benefits to be spread more widely than is possible with any
other energy efficiency measure. In order to popularize the adoption of
CFL in Taiwan, the authority proposes to implement a new energy efficient lamp comparative label system. The current study was
accordingly undertaken to investigate the factors affecting the performance and the deviation of actual and labeled performance of
commercially available integrated CFLs. In this paper, standard test
methods to determine the electrical and photometric performances of
CFL were developed based on CIE 84-1989 and CIE 60901-1987,
then 55 selected CFLs from market were tested. The results show that
with higher color temperature of CFLs lower efficacy are achieved. It
was noticed that the most packaging of CFL often lack the information of Color Rendering Index. Also, there was no correlation between
price and performance of the CFLs was indicated in this work. The results of this paper might help consumers to make more informed
CFL-purchasing decisions.
Abstract: This paper deals with the tuning of parameters for Automatic Generation Control (AGC). A two area interconnected hydrothermal system with PI controller is considered. Genetic Algorithm (GA) and Particle Swarm optimization (PSO) algorithms have been applied to optimize the controller parameters. Two objective functions namely Integral Square Error (ISE) and Integral of Time-multiplied Absolute value of the Error (ITAE) are considered for optimization. The effectiveness of an objective function is considered based on the variation in tie line power and change in frequency in both the areas. MATLAB/SIMULINK was used as a simulation tool. Simulation results reveal that ITAE is a better objective function than ISE. Performances of optimization algorithms are also compared and it was found that genetic algorithm gives better results than particle swarm optimization algorithm for the problems of AGC.
Abstract: In this article a modification of the algorithm of the fuzzy ART network, aiming at returning it supervised is carried out. It consists of the search for the comparison, training and vigilance parameters giving the minimum quadratic distances between the output of the training base and those obtained by the network. The same process is applied for the determination of the parameters of the fuzzy ARTMAP giving the most powerful network. The modification consist in making learn the fuzzy ARTMAP a base of examples not only once as it is of use, but as many time as its architecture is in evolution or than the objective error is not reached . In this way, we don-t worry about the values to impose on the eight (08) parameters of the network. To evaluate each one of these three networks modified, a comparison of their performances is carried out. As application we carried out a classification of the image of Algiers-s bay taken by SPOT XS. We use as criterion of evaluation the training duration, the mean square error (MSE) in step control and the rate of good classification per class. The results of this study presented as curves, tables and images show that modified fuzzy ARTMAP presents the best compromise quality/computing time.
Abstract: The paper investigates the potential of support vector
machines and Gaussian process based regression approaches to
model the oxygen–transfer capacity from experimental data of
multiple plunging jets oxygenation systems. The results suggest the
utility of both the modeling techniques in the prediction of the
overall volumetric oxygen transfer coefficient (KLa) from operational
parameters of multiple plunging jets oxygenation system. The
correlation coefficient root mean square error and coefficient of
determination values of 0.971, 0.002 and 0.945 respectively were
achieved by support vector machine in comparison to values of
0.960, 0.002 and 0.920 respectively achieved by Gaussian process
regression. Further, the performances of both these regression
approaches in predicting the overall volumetric oxygen transfer
coefficient was compared with the empirical relationship for multiple
plunging jets. A comparison of results suggests that support vector
machines approach works well in comparison to both empirical
relationship and Gaussian process approaches, and could successfully
be employed in modeling oxygen-transfer.
Abstract: A hybrid Photovoltaic/Thermal (PV/T) solar system integrates photovoltaic and solar thermal technologies into one single solar energy device, with dual generation of electricity and heat energy. The aim of the present study is to evaluate the potential for introduction of the PV/T technology into Northern China. For this purpose, outdoor experiments were conducted on a prototype of a PV/T water-heating system. The annual thermal and electrical performances were investigated under the climatic conditions of Beijing. An economic analysis of the system was then carried out, followed by a sensitivity study. The analysis revealed that the hybrid system is not economically attractive with the current market and energy prices. However, considering the continuous commitment of the Chinese government towards policy development in the renewable energy sector, and technological improvements like the increasing cost-effectiveness of PV cells, PV/Thermal technology may become economically viable in the near future.
Abstract: Gene, principal unit of inheritance, is an ordered
sequence of nucleotides. The genes of eukaryotic organisms include
alternating segments of exons and introns. The region of
Deoxyribonucleic acid (DNA) within a gene containing instructions
for coding a protein is called exon. On the other hand, non-coding
regions called introns are another part of DNA that regulates gene
expression by removing from the messenger Ribonucleic acid (RNA)
in a splicing process. This paper proposes to determine splice
junctions that are exon-intron boundaries by analyzing DNA
sequences. A splice junction can be either exon-intron (EI) or intron
exon (IE). Because of the popularity and compatibility of the
artificial neural network (ANN) in genetic fields; various ANN
models are applied in this research. Multi-layer Perceptron (MLP),
Radial Basis Function (RBF) and Generalized Regression Neural
Networks (GRNN) are used to analyze and detect the splice junctions
of gene sequences. 10-fold cross validation is used to demonstrate
the accuracy of networks. The real performances of these networks
are found by applying Receiver Operating Characteristic (ROC)
analysis.
Abstract: This article experimentally investigates the
thermal performance of thermoelectric air-cooling module
which comprises a thermoelectric cooler (TEC) and an
air-cooling heat sink. The influences of input current and heat
load are determined. And performances under each situation
are quantified by thermal resistance analysis. Since TEC
generates Joule heat, this nature makes construction of thermal
resistance network difficult. To simplify the analysis, this
article emphasizes on the resistance heat load might meet when
passing through the device. Therefore, the thermal resistances
in this paper are to divide temperature differences by heat load.
According to the result, there exists an optimum input current
under every heating power. In this case, the optimum input
current is around 6A or 7A. The performance of the heat sink
would be improved with TEC under certain heating power and
input current, especially at a low heat load. According to the
result, the device can even make the heat source cooler than the
ambient. However, TEC is not always effective at every heat
load and input current. In some situation, the device works
worse than the heat sink without TEC. To determine the
availability of TEC, this study figures out the effective
operating region in which the TEC air-cooling module works
better than the heat sink without TEC. The result shows that
TEC is more effective at a lower heat load. If heat load is too
high, heat sink with TEC will perform worse than without TEC.
The limit of this device is 57W. Besides, TEC is not helpful if
input current is too high or too low. There is an effective range
of input current, and the range becomes narrower when the heat
load grows.
Abstract: Software effort estimation is the process of predicting
the most realistic use of effort required to develop or maintain
software based on incomplete, uncertain and/or noisy input. Effort
estimates may be used as input to project plans, iteration plans,
budgets. There are various models like Halstead, Walston-Felix,
Bailey-Basili, Doty and GA Based models which have already used
to estimate the software effort for projects. In this study Statistical
Models, Fuzzy-GA and Neuro-Fuzzy (NF) Inference Systems are
experimented to estimate the software effort for projects. The
performances of the developed models were tested on NASA
software project datasets and results are compared with the Halstead,
Walston-Felix, Bailey-Basili, Doty and Genetic Algorithm Based
models mentioned in the literature. The result shows that the NF
Model has the lowest MMRE and RMSE values. The NF Model
shows the best results as compared with the Fuzzy-GA based hybrid
Inference System and other existing Models that are being used for
the Effort Prediction with lowest MMRE and RMSE values.
Abstract: This paper presents a new method for the
implementation of a direct rotor flux control (DRFOC) of induction
motor (IM) drives. It is based on the rotor flux components
regulation. The d and q axis rotor flux components feed proportional
integral (PI) controllers. The outputs of which are the target stator
voltages (vdsref and vqsref). While, the synchronous speed is depicted at
the output of rotor speed controller. In order to accomplish variable
speed operation, conventional PI like controller is commonly used.
These controllers provide limited good performances over a wide
range of operations even under ideal field oriented conditions. An
alternate approach is to use the so called fuzzy logic controller. The
overall investigated system is implemented using dSpace system
based on digital signal processor (DSP). Simulation and experimental
results have been presented for a one kw IM drives to confirm the
validity of the proposed algorithms.
Abstract: In the paper, the relative performances on spectral
classification of short exon and intron sequences of the human and
eleven model organisms is studied. In the simulations, all
combinations of sixteen one-sequence numerical representations, four
threshold values, and four window lengths are considered. Sequences
of 150-base length are chosen and for each organism, a total of
16,000 sequences are used for training and testing. Results indicate
that an appropriate combination of one-sequence numerical
representation, threshold value, and window length is essential for
arriving at top spectral classification results. For fixed-length
sequences, the precisions on exon and intron classification obtained
for different organisms are not the same because of their genomic
differences. In general, precision increases as sequence length
increases.
Abstract: This paper proposes the application of a hierarchical fuzzy system (HFS) based on multi-input power system stabilizer (MPSS) and also Static Var Compensator (SVC) in multi-machine environment.The number of rules grows exponentially with the number of variables in a conventional fuzzy logic system. The proposed HFS method is developed to solve this problem. To reduce the number of rules the HFS consists of a number of low-dimensional fuzzy systems in a hierarchical structure. In fact, by using HFS the total number of involved rules increases only linearly with the number of input variables. In the MPSS, to have better efficiency an auxiliary signal of reactive power deviation (ΔQ) is added with ΔP+ Δω input type Power system stabilizer (PSS). Phasor model of SVC is described and used in this paper. The performances of MPSS, Conventional power system stabilizer (CPSS), hierarchical Fuzzy Multi-input Power System Stabilizer (HFMPSS) and the proposed method in damping inter-area mode of oscillation are examined in response to disturbances. By using digital simulations the comparative study is illustrated. It can be seen that the proposed PSS is performing satisfactorily within the whole range of disturbances.
Abstract: The modern telecommunication industry demands
higher capacity networks with high data rate. Orthogonal frequency
division multiplexing (OFDM) is a promising technique for high data
rate wireless communications at reasonable complexity in wireless
channels. OFDM has been adopted for many types of wireless
systems like wireless local area networks such as IEEE 802.11a, and
digital audio/video broadcasting (DAB/DVB). The proposed research
focuses on a concatenated coding scheme that improve the
performance of OFDM based wireless communications. It uses a
Redundant Residue Number System (RRNS) code as the outer code
and a convolutional code as the inner code. Here, a direct conversion
of analog signal to residue domain is done to reduce the conversion
complexity using sigma-delta based parallel analog-to-residue
converter. The bit error rate (BER) performances of the proposed
system under different channel conditions are investigated. These
include the effect of additive white Gaussian noise (AWGN),
multipath delay spread, peak power clipping and frame start
synchronization error. The simulation results show that the proposed
RRNS-Convolutional concatenated coding (RCCC) scheme provides
significant improvement in the system performance by exploiting the
inherent properties of RRNS.
Abstract: Traffic Engineering (TE) is the process of controlling
how traffic flows through a network in order to facilitate efficient and
reliable network operations while simultaneously optimizing network
resource utilization and traffic performance. TE improves the
management of data traffic within a network and provides the better
utilization of network resources. Many research works considers intra
and inter Traffic Engineering separately. But in reality one influences
the other. Hence the effective network performances of both inter and
intra Autonomous Systems (AS) are not optimized properly. To
achieve a better Joint Optimization of both Intra and Inter AS TE, we
propose a joint Optimization technique by considering intra-AS
features during inter – AS TE and vice versa. This work considers the
important criterion say latency within an AS and between ASes. and
proposes a Bi-Criteria Latency optimization model. Hence an overall
network performance can be improved by considering this jointoptimization
technique in terms of Latency.