Abstract: A parametric study on circular thin-walled pipes
subjected to pure bending is performed. Both straight and curved
pipes are considered. Ratio D/t, initial pipe curvature and internal
pressure are the parameters varying in the analyses. The study is
mainly FEA-based.
It is found that negative curvatures (opposite to bending moment)
considerably increase stiffness and buckling limit of the pipe when no
internal pressure is acting and, similarly, positive curvatures decrease
the stiffness and buckling limit. For internal pressurised pipes the
effects of initial pipe curvature are less relevant. Results show that
this phenomenon is in relationship with the cross-section deformation
due to bending moment, which undergoes relevant ovalisation for no
pressurised pipes and little ovalisation for pressurised pipes.
Abstract: Well-designed composite steel and concrete structures
highlight the good material properties and lower the deficiencies of
steel and concrete, in particular they make use of high tensile strength
of steel and high stiffness of concrete. The most common composite
steel and concrete structure is a simply supported beam, which
concrete slab transferring the slab load to a beam is connected to the
steel cross-section. The aim of this paper is to find the most adequate
numerical model of a simply supported composite beam with the
cross-sectional and material parameters based on the results of a
processed parametric study and numerical analysis. The paper also
evaluates the suitability of using compact concrete with the
lightweight aggregates for composite steel and concrete beams. The
most adequate numerical model will be used in the resent future to
compare the results of laboratory tests.
Abstract: In this numerical study, we want to present the design
of highly efficient extruded-type heat sink. The symmetrically
arranged extruded-type heat sinks are used instead of a single extruded
or swaged-type heat sink. In this parametric study, the maximum
temperatures, the base temperatures between heaters, and the heat
release rates were investigated with respect to the arrangements of heat
sources, air flow rates, and amounts of heat input. Based on the results
we believe that the use of both side of heat sink is to be much better for
release the heat than the use of single side. Also from the results, it is
believed that the symmetric arrangement of heat sources is
recommended to achieve a higher heat transfer from the heat sink.
Abstract: In this paper analysis of an infinite beam resting on tensionless extensible geosynthetic reinforced granular bed overlying soft soil strata under moving load with constant velocity is presented. The beam is subjected to a concentrated load moving with constant velocity. The upper reinforced granular bed is modeled by a rough elastic membrane embedded in Pasternak shear layer overlying a series of compressible nonlinear Winkler springs representing the under-lied very poor soil. The tensionless extensible geosynthetic layer has been assumed to deform such that at interface the geosynthetic and the soil have some deformation. Nonlinear behavior of granular fill and the very poor soil has been considered in the analysis by means of hyperbolic constitutive relationships. Detailed parametric study has been conducted to study the influence of various parameters on the response of soil foundation system under consideration by means of deflection and bending moment in the beam and tension mobilized in the geosynthetic layer. This study clearly observed that the comparisons of tension and tensionless foundation and magnitude of applied load, relative compressibility of granular fill and ultimate resistance of poor soil has significant influence on the response of soil foundation system.
Abstract: Accurate dynamic modeling and analysis of flexible link manipulator (FLM) with non linear dynamics is very difficult due to distributed link flexibility and few studies have been conducted based on assumed modes method (AMM) and finite element models. In this paper a nonlinear dynamic model with first two elastic modes is derived using combined Euler/Lagrange and AMM approaches. Significant dynamics associated with the system such as hub inertia, payload, structural damping, friction at joints, combined link and joint flexibility are incorporated to obtain the complete and accurate dynamic model. The response of the FLM to the applied bang-bang torque input is compared against the models derived from LS-DYNA finite element discretization approach and linear finite element models. Dynamic analysis is conducted using LS-DYNA finite element model which uses the explicit time integration scheme to simulate the system. Parametric study is conducted to show the impact payload mass. A numerical result shows that the LS-DYNA model gives the smooth hub-angle profile.
Abstract: Magnetohydrodynamic free convection fluid flow and heat transfer in a square cavity filled with an electric conductive fluid with Prandtl number of 0.7 has been investigated numerically. The horizontal bottom wall of the cavity was kept at Th while the side and the top walls of the cavity were maintained at a constant temperature Tc with Th>Tc. The governing equations written in terms of the primitive variables were solved numerically using the finite volume method while the SIMPLER algorithm was used to couple the velocity and pressure fields. Using the developed code, a parametric study was performed, and the effects of the Rayleigh number and the Hartman number on the fluid flow and heat transfer inside the cavity were investigated. The obtained results showed that temperature distribution and flow pattern inside the cavity depended on both strength of the magnetic field and Rayleigh number. For all cases two counter rotating eddies were formed inside the cavity. The magnetic field decreased the intensity of free convection and flow velocity. Also it was found that for higher Rayleigh numbers a relatively stronger magnetic field was needed to decrease the heat transfer through free convection.
Abstract: A study on grindability of chopped strand mat glass fiber reinforced polymer laminates (CSM GFRP) have been carried out to evaluate the significant parameters on wheel performance. Performance of Aluminum oxide and c-BN wheels during grinding of CSM GFRP laminate was evaluated in terms of grinding force and surface roughness during grinding. The cubic Boron Nitride wheel experiences higher tangential grinding forces components and lower normal force component than Aluminum oxide grinding wheels. In case of surface finish, Aluminum oxide grinding wheels outdo the cubic Boron Nitride grinding wheels.
Abstract: Numerical investigation on the generality of nanoparticle velocity equation had been done on the previous published work. The three dimensional governing equations (continuity, momentum and energy) were solved using finite volume method (FVM). Parametric study of thermal performance between pure water-cooled and nanofluid-cooled are evaluated for volume fraction in the range of 1% to 4%, and nanofluid type of gamma-Al2O3 at Reynolds number range of 67.41 to 286.77. The nanofluid is modeled using single and two phase approach. Three different existing Brownian motion velocities are applied in comparing the generality of the equation for a wide parametric condition. Deviation in between the Brownian motion velocity is identified to be due to the different means of mean free path and constant value used in diffusion equation.
Abstract: The mixing of two or more liquids is very common in many industrial applications from automotive to food processing. CFD simulations of these processes require comparison with test results. In many cases it is practically impossible. Therefore, comparison provides with scalable tests. So, parameterization of the problem is sufficient to capture the performance of the mixer.
However, the influence of geometrical and thermo-physical parameters on the mixing is not well understood.
In this work influence of geometrical and thermal parameters was studied. It was shown that for full developed turbulent flows (Re > 104), Pet»const and concentration of secondary fluid ~ F(r/l).
In other words, the mixing is practically independent of total flow rate and scale for a given geometry and ratio of flow rates of mixing flows. This statement was proved in present work for different geometries and mixtures such as EGR and water-urea mixture.
Present study has been shown that the best way to improve the mixing is to establish geometry with the lowest Pet number possible by intensifying the turbulence in the domain. This is achievable by using step geometry, impinging flow EGR on a wall, or EGR jets, with a strong change in the flow direction, or using swirler like flow in the domain or combination all of these factors. All of these results are applicable to any mixtures of no compressible fluids.
Abstract: This paper is devoted to predict laminar and turbulent
heating rates around blunt re-entry spacecraft at hypersonic
conditions. Heating calculation of a hypersonic body is normally
performed during the critical part of its flight trajectory. The
procedure is of an inverse method, where a shock wave is assumed,
and the body shape that supports this shock, as well as the flowfield
between the shock and body, are calculated. For simplicity the
normal momentum equation is replaced with a second order pressure
relation; this simplification significantly reduces computation time.
The geometries specified in this research, are parabola and ellipsoids
which may have conical after bodies. An excellent agreement is
observed between the results obtained in this paper and those
calculated by others- research. Since this method is much faster than
Navier-Stokes solutions, it can be used in preliminary design,
parametric study of hypersonic vehicles.
Abstract: There are several ways of improving the performance of a vapor compression refrigeration cycle. Use of an ejector as expansion device is one of the alternative ways. The present paper aims at evaluate the performance improvement of a vapor compression refrigeration cycle under a wide range of operating conditions. A numerical model is developed and a parametric study of important parameters such as condensation (30-50°C) and evaporation temperatures (-20-5°C), nozzle and diffuser efficiencies (0.75-0.95), subcooling and superheating degrees (0-15K) are investigated. The model verification gives a good agreement with the literature data. The simulation results revealed that condensation temperature has the highest effect (129%) on the performance improvement ratio while superheating has the lowest one (6.2%). Among ejector efficiencies, the diffuser efficiency has a significant effect on the COP of ejector expansion refrigeration cycle. The COP improvement percentage decreases from 10.9% to 4.6% as subcooling degrees increases by 15K.
Abstract: The aim of the current work is to present a comparison among three popular optimization methods in the inverse elastostatics problem (IESP) of flaw detection within a solid. In more details, the performance of a simulated annealing, a Hooke & Jeeves and a sequential quadratic programming algorithm was studied in the test case of one circular flaw in a plate solved by both the boundary element (BEM) and the finite element method (FEM). The proposed optimization methods use a cost function that utilizes the displacements of the static response. The methods were ranked according to the required number of iterations to converge and to their ability to locate the global optimum. Hence, a clear impression regarding the performance of the aforementioned algorithms in flaw identification problems was obtained. Furthermore, the coupling of BEM or FEM with these optimization methods was investigated in order to track differences in their performance.
Abstract: Numerical parametric study is conducted to study the effects of ampoule rotation on the flows and the dopant segregation in vertical bridgman (vb) crystal growth. Calculations were performed in unsteady state. The extended darcy model, which includes the time derivative and coriolis terms, has been employed in the momentum equation. It’s found that the convection, and dopant segregation can be affected significantly by ampoule rotation, and the effect is similar to that by an axial magnetic field. Ampoule rotation decreases the intensity of convection and stretches the flow cell axially. When the convection is weak, the flow can be suppressed almost completely by moderate ampoule rotation and the dopant segregation becomes diffusion-controlled. For stronger convection, the elongated flow cell by ampoule rotation may bring dopant mixing into the bulk melt reducing axial segregation at the early stage of the growth. However, if the cellular flow cannot be suppressed completely, ampoule rotation may induce larger radial segregation due to poor mixing.
Abstract: Conventional concentrically-braced frame (CBF)
systems have limited drift capacity before brace buckling and related
damage leads to deterioration in strength and stiffness. Self-centering
concentrically-braced frame (SC-CBF) systems have been developed
to increase drift capacity prior to initiation of damage and minimize
residual drift. SC-CBFs differ from conventional CBFs in that the
SC-CBF columns are designed to uplift from the foundation at a
specified level of lateral loading, initiating a rigid-body rotation
(rocking) of the frame. Vertically-aligned post-tensioning bars resist
uplift and provide a restoring force to return the SC-CBF columns to
the foundation (self-centering the system). This paper presents a
parametric study of different prototype buildings using SC-CBFs.
The bay widths of the SC-CBFs have been varied in these buildings
to study different geometries. Nonlinear numerical analyses of the
different SC-CBFs are presented to illustrate the effect of frame
geometry on the behavior and dynamic response of the SC-CBF
system.
Abstract: In this research, a 2-D computational analysis of
steady state free convection in a rectangular enclosure filled with an
electrically conducting fluid under Effect of Magnetic Field has been
performed. The governing equations (mass, momentum, and energy)
are formulated and solved by a finite volume method (FVM)
subjected to different boundary conditions. A parametric study has
been conducted to consider the influence of Grashof number (Gr),
Prantdl number (Pr) and the orientation of magnetic field on the flow
and heat transfer characteristics. It is observed that Nusselt number
(Nu) and heat flux will increase with increasing Grashof and Prandtl
numbers and decreasing the slope of the orientation of magnetic field.
Abstract: In the present paper the results of a numerical study are presented, numerical models were developed to simulate the behaviour of vertical massive dikes. The proposed models were developed according to the geometry, boundary conditions, loading conditions and initial conditions of a physical model taken as reference. The results obtained were compared to the experimental data. As far as the overall behaviour, the displacements and the failure mechanisms of the dikes is concerned, the numerical results were in good agreement with the experimental results, which clearly indicates a good quality of numerical modelling. The validated numerical models were used in a parametric study were the displacements and failure mechanisms were fully investigated. Out of the results obtained, some conclusions and recommendations related to the design of massive dikes are proposed.
Abstract: Numerical studies have been carried out using a two
dimensional code to examine the influence of pressure / thrust
transient of solid propellant rockets at liftoff. This code solves
unsteady Reynolds-averaged thin-layer Navier–Stokes equations by
an implicit LU-factorization time-integration method. The results
from the parametric study indicate that when the port is narrow there
is a possibility of increase in pressure / thrust-rise rate due to
relatively high flame spread rate. Parametric studies further reveal
that flame spread rate can be altered by altering the propellant
properties, igniter jet characteristics and nozzle closure burst pressure
without altering the grain configuration and/or the mission
demanding thrust transient. We observed that when the igniter
turbulent intensity is relatively low the vehicle could liftoff early due
to the early flow choking of the rocket nozzle. We concluded that the
high pressurization-rate has structural implications at liftoff in
addition to transient burning effect. Therefore prudent selection of the
port geometry and the igniter, for meeting the mission requirements,
within the given envelop are meaningful objectives for any designer
for the smooth liftoff of solid propellant rockets.
Abstract: A parametric study of a mixed-compression
supersonic inlet is performed and reported. The effects of inlet Mach
Numbers, varying from 4 to 10, and angle of attack, varying from 0
to 10, are reported for a constant inlet dynamic pressure. The paper
looked at the variations of mass flow rates through the inlet, gain in
entropy through the inlet, and the angles of the external oblique
shocks. The mass flow rates were found to decrease monotonically
with Mach numbers and increase with angle of attacks. On the other
hand the entropy gain through the inlet increased with increasing
Mach number and angle of attack. The variation in static pressure
was found to be identical from the inlet throat to the exit for Mach
number values higher than 6.
Abstract: In the current work, a numerical parametric study was
performed in order to model the fluid mechanics in the riser of a
bubbling fluidized bed (BFB). The gas-solid flow was simulated by
mean of a multi-fluid Eulerian model incorporating the kinetic theory
for solid particles. The bubbling fluidized bed was simulated two
dimensionally by mean of a Computational Fluid Dynamic (CFD)
commercial software package, Fluent. The effects of using different
inter-phase drag function (the drag model of Gidaspow, Syamlal and
O-Brien and the EMMS drag model) on the model predictions were
evaluated and compared. The results showed that the drag models of
Gidaspow and Syamlal and O-Brien overestimated the drag force for
the FCC particles and predicted a greater bed expansion in
comparison to the EMMS drag model.
Abstract: To understand the seismic behavior of the offshore
structures, the dynamic interaction of the water-structure-soil should
be assessed. In this regard the role of the water dynamic properties in
magnifying or reducing of the effects of earthquake induced motions
on offshore structures haven't been investigated in precise manner in
available literature. In this paper the sea water level fluctuations
effects on the seismic behavior of a sample of offshore structures has
been investigated by emphasizing on the water-structure interaction
phenomenon. For this purpose a two dimensional finite element
model of offshore structures as well as surrounded water has been
developed using ANSYS software. The effect of soil interaction with
embedded pile foundation has been imposed by using a series of
nonlinear springs in horizontal and vertical directions in soil-piles
contact points. In the model, the earthquake induced motions have
been applied on springs and consequently the motions propagated
upward to the structure and surrounded water. As a result of
numerical study, the horizontal deformations of the offshore deck as
well as internal force and buckling coefficient in structural elements
have been recorded and controlled with and without water presence.
In part of study a parametric study has been accomplished on sea
water level fluctuations and effect of this parameter has been studied
on the aforementioned numerical results.