Abstract: The study assessed the effect of crude oil applied at rates, 0, 2, 5, and 10% on the fractional chemical forms and availability of some metals in soils from Usen, Edo State, with no known crude oil contamination and soil from a crude oil spill site in Ubeji, Delta State, Nigeria. Three methods were used to determine the bioavailability of metals in the soils: maize (Zea mays) plant, EDTA and BCR sequential extraction. The sequential extract acid soluble fraction of the BCR extraction (most labile fraction of the soils, normally associated with bioavailability) were compared with total metal concentration in maize seedlings as a means to compare the chemical and biological measures of bioavailability. Total Fe was higher in comparison to other metals for the crude oil contaminated soils. The metal concentrations were below the limits of 4.7% Fe, 190mg/kg Cu and 720mg/kg Zn intervention values and 36mg/kg Cu and 140mg/kg Zn target values for soils provided by the Department of Petroleum Resources (DPR) guidelines. The concentration of the metals in maize seedlings increased with increasing rates of crude oil contamination. Comparison of the metal concentrations in maize seedlings with EDTA extractable concentrations showed that EDTA extracted more metals than maize plant.
Abstract: Heavy metals have a damaging impact for the environment, animals and humans due to their extreme toxicity and removing them from wastewaters is a very important and interesting task in the field of water pollution control. Biosorption is a relatively new method for treatment of wastewaters and recovery of heavy metals. In this study, a continuous fixed bed study was carried out by using Bacillus thuringiensis as a biosorbent for the removal of Cu and Mn ions from Sarcheshmeh Acid Mine Drainage (AMD). The effect of operating parameters such as flow rate and bed height on the sorption characteristics of B. thuringiensis was investigated at pH 6.0 for each metal ion. The experimental results showed that the breakthrough time decreased with increasing flow rate and decreasing bed height. The data also indicated that the equilibrium uptake of both metals increased with decreasing flow rate and increasing bed height. BDST, Thomas, and Yoon–Nelson models were applied to experimental data to predict the breakthrough curves. All models were found suitable for describing the whole dynamic behavior of the column with respect to flow rate and bed height. In order to regenerate the adsorbent, an elution step was carried out with 1 M HCl and five adsorption-desorption cycles were carried out in continuous manner.
Abstract: Water is a very rare natural resource in South Africa. Ga-Selati River is used for both domestic and industrial purposes. This study was carried out in order to assess the quality of Ga-Selati River in a mining area of Limpopo Province-Phalaborwa. The pH, Electrical Conductivity (EC) and Total Dissolved Solids (TDS) were determined using a Crinson multimeter while turbidity was measured using a Labcon Turbidimeter. The concentrations of Al, Ca, Cd, Cr, Fe, K, Mg, Mn, Na and Pb were analysed in triplicate using a Varian 520 flame atomic absorption spectrometer (AAS) supplied by PerkinElmer, after acid digestion with nitric acid in a fume cupboard. The average pH of the river from eight different sampling sites was 8.00 and 9.38 in wet and dry season respectively. Higher EC values were determined in the dry season (138.7 mS/m) than in the wet season (96.93 mS/m). Similarly, TDS values were higher in dry (929.29 mg/L) than in the wet season (640.72 mg/L) season. These values exceeded the recommended guideline of South Africa Department of Water Affairs and Forestry (DWAF) for domestic water use (70 mS/m) and that of the World Health Organization (WHO) (600 mS/m), respectively. Turbidity varied between 1.78-5.20 and 0.95-2.37 NTU in both wet and dry seasons. Total hardness of 312.50 mg/L and 297.75 mg/L as the concentration of CaCO3 was computed for the river in both the wet and the dry seasons and the river water was categorised as very hard. Mean concentration of the metals studied in both the wet and the dry seasons are: Na (94.06 mg/L and 196.3 mg/L), K (11.79 mg/L and 13.62 mg/L), Ca (45.60 mg/L and 41.30 mg/L), Mg (48.41 mg/L and 44.71 mg/L), Al (0.31 mg/L and 0.38 mg/L), Cd (0.01 mg/L and 0.01 mg/L), Cr (0.02 mg/L and 0.09 mg/L), Pb (0.05 mg/L and 0.06 mg/L), Mn (0.31 mg/L and 0.11 mg/L) and Fe (0.76 mg/L and 0.69 mg/L). Results from this study reveal that most of the metals were present in concentrations higher than the recommended guidelines of DWAF and WHO for domestic use and the protection of aquatic life.
Abstract: Landfill leachates contain a number of persistent pollutants, including heavy metals. They have the ability to spread in ecosystems and accumulate in fish which most of them are classified as top-consumers of trophic chains. Fish are freely swimming organisms; but perhaps, due to their species-specific ecological and behavioral properties, they often prefer the most suitable biotopes and therefore, did not avoid harmful substances or environments. That is why it is necessary to evaluate the persistent pollutant dispersion in hydroecosystem using fish tissue metal concentration. In hydroecosystems of hybrid type (e.g. river-pond-river) the distance from the pollution source could be a perfect indicator of such a kind of metal distribution. The studies were carried out in the Kairiai landfill neighboring hybrid-type ecosystem which is located 5 km east of the Šiauliai City. Fish tissue (gills, liver, and muscle) metal concentration measurements were performed on two types of ecologically-different fishes according to their feeding characteristics: benthophagous (Gibel carp, roach) and predatory (Northern pike, perch). A number of mathematical models (linear, non-linear, using log and other transformations) have been applied in order to identify the most satisfactorily description of the interdependence between fish tissue metal concentration and the distance from the pollution source. However, the only one log-multiple regression model revealed the pattern that the distance from the pollution source is closely and positively correlated with metal concentration in all predatory fish tissues studied (gills, liver, and muscle).
Abstract: This study focuses on the hydro-geology and chemical
constituents analysis of Ikogosi Warm Spring waters in South West
Nigeria. Ikogosi warm spring is a global tourist attraction because it
has both warm and cold spring sources. Water samples from the cold
spring, warm spring and the meeting point were collected, analyzed
and the result shows close similarity in temperature, hydrogen iron
concentration (pH), alkalinity, hardness, Calcium, Magnesium,
Sodium, Iron, total dissolved solid and heavy metals. The measured
parameters in the water samples are within World Health
Organisation standards for fresh water. The study of the geology of
the warm spring reveals that the study area is underlain by a group of
slightly migmatised to non-migmatised paraschists and meta-igneous
rocks. Also, concentration levels of selected heavy metals, (Copper,
Cadmium, Zinc, Arsenic and Cromium) were determined in the water
(ppm) samples. Chromium had the highest concentration value of
1.52ppm (an average of 49.67%) and Cadmium had the lowest
concentration with value of 0.15ppm (an average of 4.89%).
Comparison of these results showed that, their mean levels are within
the standard values obtained in Nigeria. It can be concluded that both
warm and spring water are safe for drinking.
Abstract: Ceramic obtained on the base of aluminum oxide has
wide application range, because it has unique properties, for example,
wear-resistance, dielectric characteristics, and exploitation ability at
high temperatures and in corrosive atmosphere. Low temperature
synthesis of α-Al2O3 is energo-economical process and it is topical
for developing technologies of corundum ceramics fabrication. In the present work possibilities of low temperature transformation
of oxyhydroxides in α-Al2O3, during the presence of small amount of
rare–earth elements compounds (also Th, Re), have been discussed.
Aluminum unstable oxyhydroxides have been obtained by hydrolysis
of aluminium isopropoxide, nitrates, sulphate, and chloride in
alkaline environment at 80-90ºC temperatures. β-Al(OH)3 has been
received from aluminum powder by ultrasonic development. Drying
of oxyhydroxide sol has been conducted with presence of various
types seeds, which amount reaches 0,1-0,2% (mas). Neodymium,
holmium, thorium, lanthanum, cerium, gadolinium, disprosium
nitrates and rhenium carbonyls have been used as seeds and they
have been added to the sol specimens in amount of 0.1-0.2% (mas)
calculated on metals. Annealing of obtained gels is carried out at 70–
1100ºC for 2 hrs. The same specimen transforms in α-Al2O3 at
1100ºC. At this temperature in case of presence of lanthanum and
gadolinium transformation takes place by 70-85%. In case of
presence of thorium stabilization of γ-and θ-phases takes place. It is
established, that thorium causes inhibition of α-phase generation at
1100ºC, and at the time when in all other doped specimens α-phase is
generated at lower temperatures (1000-1050ºC). Synthesis of various
type compounds and simultaneous consolidation has developed in the
furnace of OXY-GON. Composite materials containing oxide and
non-oxide components close to theoretical data have been obtained in
this furnace respectively. During the work the following devices have
been used: X-ray diffractometer DRON-3M (Cu-Kα, Ni filter,
2º/min), High temperature vacuum furnace OXY-GON, electronic
scanning microscopes Nikon ECLIPSE LV 150, NMM-800TRF,
planetary mill Pulverisette 7 premium line, SHIMADZU Dynamic
Ultra Micro Hardness Tester, DUH-211S, Analysette 12 Dyna sizer.
Abstract: In recent years, the use of the aluminum based alloys
in the industry and technology are increasing. Alloying elements in
aluminum have further been improving the strength and stiffness
properties that provide superior compared to other metals. In this
study, investigation of physical properties (microstructure,
microhardness, tensile strength, electrical conductivity and thermal
properties) in the Al-12.6wt.%Si-%2wt.Ni ternary alloy were
investigated. Al-Si-Ni alloy was prepared in vacuum atmosphere. The
samples were directionally solidified upwards with different growth
rate V (8.3−165.45 μm/s) at constant temperature gradient G (7.73
K/mm). The flake spacings (λ), microhardness (HV), ultimate tensile
strength (σ), electrical resistivity (ρ) and thermal properties (H, Cp,
Tm) of the samples were measured. Influence of the growth rate and
spacings on microhardness, ultimate tensile strength and electrical
resistivity were investigated and relationships between them were
obtained. According to results, λ values decrease with increasing V,
but HV, σ and ρ values increase with increasing V. Variations of
electrical resistivity (ρ) of solidified samples were also measured.
The enthalpy of fusion (H) and specific heat (Cp) for the alloy was
also determined by differential scanning calorimeter (DSC) from
heating trace during the transformation from liquid to solid. The
results in this work were compared with the previous similar
experimental results.
Abstract: In this article, the antibiogram and heavy metal
resistance profile of the bacteria isolated from total 34 studied
animals (Pelophylax ridibundus = 12; Mauremys rivulata = 14;
Natrix natrix = 8) captured around the Biga Stream, are described.
There was no database information on antibiogram and heavy metal
resistance profile of bacteria from these area’s amphibians and
reptiles.
A total of 200 bacteria were successfully isolated from cloaca and
oral samples of the aquatic amphibians and reptiles as well as from
the water sample. According to Jaccard’s similarity index, the degree
of similarity in the bacterial flora was quite high among the
amphibian and reptile species under examination, whereas it was
different from the bacterial diversity in the water sample. The most
frequent isolates were A. hydrophila (31.5%), B. pseudomallei
(8.5%), and C. freundii (7%). The total numbers of bacteria obtained
were as follows: 45 in P. ridibundus, 45 in N. natrix 30 in M.
rivulata, and 80 in the water sample. The result showed that
cefmetazole was the most effective antibiotic to control the bacteria
isolated in this study and that approximately 93.33% of the bacterial
isolates were sensitive to this antibiotic. The multiple antibiotic
resistances (MAR) index indicated that P. ridibundus (0.95) > N.
natrix (0.89) > M. rivulata (0.39). Furthermore, all the tested heavy
metals (Pb+2, Cu+2, Cr+3, and Mn+2) inhibit the growth of the bacterial
isolates at different rates. Therefore, it indicated that the water source
of the animals was contaminated with both antibiotic residues and
heavy metals.
Abstract: Freshly laid eggs from green turtles, Chelonia mydas,
were randomly collected from Ras Al-Hadd Reserve, Oman.
Eggshells taken from eggs and sand collected from the body chamber
were analyzed for eight heavy metals (Al, Br, Cd, Co, Cu, Fe, S, and
Zn) using inductively coupled plasma mass spectrometry (ICP).
Heavy metal concentrations varied significantly (P
Abstract: Soil quality monitoring is a science-based soil
management tool that assesses soil ecosystem health.
A soil monitoring program in Auckland, New Zealand’s largest
city extends from 1995 to the present. The objective of this study was
to firstly determine changes in soil parameters (basic soil properties
and heavy metals) that were assessed from rural land in 1995-2000
and repeated in 2008-2012. The second objective was to determine
differences in soil parameters across various land uses including
native bush, rural (horticulture, pasture and plantation forestry) and
urban land uses using soil data collected in more recent years (2009-
2013).
Across rural land, mean concentrations of Olsen P had
significantly increased in the second sampling period and was
identified as the indicator of most concern, followed by soil
macroporosity, particularly for horticultural and pastoral land. Mean
concentrations of Cd were also greatest for pastoral and horticultural
land and a positive correlation existed between these two parameters,
which highlights the importance of analysing basic soil parameters in
conjunction with heavy metals. In contrast, mean concentrations of
As, Cr, Pb, Ni and Zn were greatest for urban sites. Native bush sites
had the lowest concentrations of heavy metals and were used to
calculate a ‘pollution index’ (PI). The mean PI was classified as high
(PI > 3) for Cd and Ni and moderate for Pb, Zn, Cr, Cu, As and Hg,
indicating high levels of heavy metal pollution across both rural and
urban soils. From a land use perspective, the mean ‘integrated
pollution index’ was highest for urban sites at 2.9 followed by
pasture, horticulture and plantation forests at 2.7, 2.6 and 0.9,
respectively.
It is recommended that soil sampling continues over time because
a longer spanning record will allow further identification of where
soil problems exist and where resources need to be targeted in the
future. Findings from this study will also inform policy and science
direction in regional councils.
Abstract: Paints are the most widely used methods of protection
against atmospheric corrosion of metals. The aim of this work was to
determine the protective performance of epoxy coating against sea
water before and after damage.
Investigations are conducted using stationary and non-stationary
electrochemical tools such as electrochemical impedance
spectroscopy has allowed us to characterize the protective qualities of
these films. The application of the EIS on our damaged in-situ
painting shows the existence of several capacitive loops which is an
indicator of the failure of our tested paint. Microscopic analysis
(micrograph) helped bring essential elements in understanding the
degradation of our paint condition and immersion training corrosion
products.
Abstract: Due to the determination of the pollution status of
fresh resources in the Egyptian territorial waters is very important for
public health; this study was carried out to reveal the levels of heavy
metals in the shellfish and their environment and its relation to the
highly developed industrial activities in those areas. A total of 100
shellfish samples from the Rosetta, Edku, El-Maadiya, Abo-Kir and
El-Max coasts [10 crustaceans (shrimp) and 10 mollusks (oysters)]
were randomly collected from each coast. Additionally, 10 samples
from both the water and the sediment were collected from each coast.
Each collected sample was analyzed for cadmium, chromium,
copper, lead and zinc residues using a Perkin Elmer atomic
absorption spectrophotometer (AAS). The results showed that the
levels of heavy metals were higher in the water and sediment from
Abo-Kir. The heavy metal levels decreased successively for the
Rosetta, Edku, El-Maadiya, and El-Max coasts, and the
concentrations of heavy metals, except copper and zinc, in shellfish
exhibited the same pattern. For the concentration of heavy metals in
shellfish tissue, the highest was zinc and the concentrations decreased
successively for copper, lead, chromium and cadmium for all coasts,
except the Abo-Kir coast, where the chromium level was highest and
the other metals decreased successively for zinc, copper, lead and
cadmium. In Rosetta, chromium was higher only in the mollusks,
while the level of this metal was lower in the crustaceans; this trend
was observed at the Edku, El-Maadiya and El-Max coasts as well.
Herein, we discuss the importance of such contamination for public
health and the sources of shellfish contamination with heavy metals.
We suggest measures to minimize and prevent these pollutants in the
aquatic environment and, furthermore, how to protect humans from
excessive intake.
Abstract: In this paper, snow samples containing dust particles
from several sampling points around the city of Ostrava were
analyzed. The pH values of sampled snow were measured and solid
particles analyzed. Particle size, zeta potential and content of selected
heavy metals were determined in solid particles. The pH values of
most samples lay in the slightly acid region. Mean values of particle
size ranged from 290.5 to 620.5 nm. Zeta potential values varied
between -5 and -26.5 mV. The following heavy metal concentration
ranges were found: copper 0.08-0.75 mg/g, lead 0.05-0.9 mg/g,
manganese 0.45-5.9 mg/g and iron 25.7-280.46 mg/g. The highest
values of copper and lead were found in the vicinity of busy
crossroads, and on the contrary, the highest levels of manganese and
iron were detected close to a large steelworks. The proportion
between pH values, zeta potentials, particle sizes and heavy metal
contents was established. Zeta potential decreased with rising pH
values and, simultaneously, heavy metal content in solid particles
increased. At the same time, higher metal content corresponded to
lower particle size.
Abstract: Pollution of the Klip River has caused
microorganisms inhabiting it to develop protective survival
mechanisms. This study isolated and characterized the heavy metal
resistant bacteria in the Klip River. Water and sediment samples were
collected from six sites along the course of the river. The pH,
turbidity, salinity, temperature and dissolved oxygen were measured
in-situ. The concentrations of six heavy metals (Cd, Cu, Fe, Ni, Pb
and Zn) of the water samples were determined by atomic absorption
spectroscopy. Biochemical and antibiotic profiles of the isolates were
assessed using the API 20E® and Kirby Bauer Method. Growth
studies were carried out using spectrophotometric methods. The
isolates were identified using 16SrDNA sequencing. The uppermost
part of the Klip River with the lowest pH had the highest levels of
heavy metals. Turbidity, salinity and specific conductivity increased
measurably at Site 4 (Henley on Klip Weir). MIC tests showed that
16 isolates exhibited high iron and lead resistance. Antibiotic
susceptibility tests revealed that the isolates exhibited multitolerances
to drugs such as Tetracycline, Ampicillin, and
Amoxicillin.
Abstract: Resistance spot welding (RSW) has been used widely to join sheet metals. It has been a challenge to get required weld quality in spot welding of dissimilar thickness materials. Weld parameters are not generally available in standards for thickness beyond 4mm. This paper presents the welding process design and parameter optimization of RSW used in joining of low carbon steel sheet of thickness 0.8 mm and metal strips of cross section 10 x 5mm for electrical motor applications. Taguchi quality design was adopted for weld current and time optimization using L9 orthogonal array. Optimum process parameters (current- 3.5kA and time- 10 cycles) were obtained from the Taguchi analysis and shear test results. Confirmation experiment result revealed that the weld quality was within acceptable interval. Further, numerical simulation of RSW process was carried out with selected weld parameters to quantify the temperature at faying surface and check for formation of appropriate nugget. The nugget geometry measured after peel test and predicted from numerical validation method were similar and in accordance with the standards.
Abstract: This paper involves a study of the heavy metal pollution of the soils around one of cement plants in Libya called Suk-Alkhameas and surrounding urban areas caused by cement kiln dust (CKD) emitted. Samples of soil was collected from sites at four directions around the cement factory at distances 250m, 1000m, and 3000m from the factory and at (0-10)cm deep in the soil. These samples are analyzed for Fe (iii), Zn(ii), and Pb (ii) as major pollutants. These values are compared with soils at 25 Km distances from the factory as a reference or control samples. The results show that the concentration of Fe ions in the surface soil was within the acceptable range of 1000ppm. However, for Zn and Pb ions the concentrations at the east and north sides of the factory were found six fold higher than the benchmark level. This high value was attributed to the wind which blows usually from south to north and from west to east. This work includes an investigation of the adsorption isotherms and adsorption efficiency of CKD as adsorbent of heavy metal ions (Fe (iii), Zn(ii), and Pb(ii)) from the polluted soils of Suk-Alkameas city. The investigation was conducted in batch and fixed bed column flow technique. The adsorption efficiency of the studied heavy metals ions removals onto CKD depends on the pH of the solution. The optimum pH values are found to be in the ranges of 8-10 and decreases at lower pH values. The removal efficiency of these heavy metals ions ranged from 93% for Pb, 94% for Zn, and 98% for Fe ions for 10 g.l-1 adsorbent concentration. The maximum removal efficiency of these ions was achieved at 50-60 minutes contact times at which equilibrium is reached. Fixed bed column experimental measurements are also made to evaluate CKD as an adsorbent for the heavy metals. Results obtained are with good agreement with Langmuir and Drachsal assumption of multilayer formation on the adsorbent surface.
Abstract: One of the causes of water pollution is the presence of heavy metals in water. In the present study, an adsorbent prepared from the raw bark of the Pongamia pinnata tree is used for the removal of ferrous or ferric ions from aqueous and waste water containing heavy metals. Adsorption studies were conducted at different pH, concentration of metal ion, amount of adsorbent, contact time, agitation and temperature. The Langmuir and Freundlich adsorption isotherm models were applied for the results. The Langmuir isotherms were best fitted by the equilibrium data. The maximum adsorption was found to 146mg/g in waste water at a temperature of 30°C which is in agreement as comparable to the adsorption capacity of different adsorbents reported in literature. Pseudo second order model best fitted the adsorption of both ferrous and ferric ions.
Abstract: Slag sample from copper smelting operation in a
water jacket furnace from DRC plant was used. The study intends to
determine the effect of cooling in the extraction of base metals. The
cooling methods investigated were water quenching, air cooling and
furnace cooling. The latter cooling ways were compared to the
original as received slag. It was observed that, the cooling rate of the
slag affected the leaching of base metals as it changed the phase
distribution in the slag and the base metals distribution within the
phases. It was also found that fast cooling of slag prevented
crystallization and produced an amorphous phase that encloses the
base metals. The amorphous slags from the slag dumps were more
leachable in acidic medium (HNO3) which leached 46%Cu, 95% Co,
85% Zn, 92% Pb and 79% Fe with no selectivity at pH0, than in
basic medium (NH4OH). The leachability was vice versa for the
modified slags by quenching in water which leached 89%Cu with a
high selectivity as metal extractions are less than 1% for Co, Zn, Pb
and Fe at ambient temperature and pH12. For the crystallized slags,
leaching of base metals increased with the increase of temperature
from ambient temperature to 60°C and decreased at the higher
temperature of 80°C due to the evaporation of the ammonia solution
used for basic leaching, the total amounts of base metals that were
leached in slow cooled slags were very low compared to the
quenched slag samples.
Abstract: Heavy metal transfer in soil profiles is a major
environmental concern because even slow transport through the soil
may eventually lead to deterioration of groundwater quality. The use
of sewage sludge and effluents from wastewater treatment plants for
irrigation of agricultural lands is on the rise particularly in peri-urban
area of developing countries. In this study soil samples under sludge
application and wastewater irrigation were studied and soil samples
were collected in the soil profiles from the surface to 100 cm in
depth. For this purpose, three plots were made in a treatment plant in
south of Tehran-Iran. First plot was irrigated just with effluent from
wastewater treatment plant, second plot with simulated heavy metals
concentration equal 50 years irrigation and in third plot sewage
sludge and effluent was used. Trace metals concentration (Cd, Cu)
were determined for soil samples. The results indicate movement of
metals was observed, but the most concentration of metals was found
in topsoil samples. The most of Cadmium concentration was
measured in the topsoil of plot 3, 4.5mg/kg and Maximum cadmium
movement was observed in 0-20 cm. The most concentration of
copper was 27.76mg/kg, and maximum percolation in 0-20 cm.
Metals (Cd, Cu) were measured in leached water. Preferential flow
and metal complexation with soluble organic apparently allow
leaching of heavy metals.
Abstract: Tailor-welded Blanks (TWBs) are tailor made for
different complex component designs by welding multiple metal
sheets with different thicknesses, shapes, coatings or strengths prior
to forming. In this study the Hemispherical Die Stretching (HDS) test
(out-of-plane stretching) of TWBs were simulated via
ABAQUS/Explicit to obtain the Forming Limit Diagrams (FLDs) of
Stainless steel (AISI 304) laser welded blanks with different
thicknesses. Two criteria were used to detect the start of necking to
determine the FLD for TWBs and parent sheet metals. These two
criteria are the second derivatives of the major and thickness strains
that are given from the strain history of simulation. In the other word,
in these criteria necking starts when the second derivative of
thickness or major strain reaches its maximum. With having the time
of onset necking, one can measure the major and minor strains at the
critical area and determine the forming limit curve.