Abstract: This paper presents a methodology towards the emulation of the electrical power consumption of the RF device during the cellular phone/handset transmission mode using the LTE technology. The emulation methodology takes the physical environmental variables and the logical interface between the baseband and the RF system as inputs to compute the emulated power dissipation of the RF device. The emulated power, in between the measured points corresponding to the discrete values of the logical interface parameters is computed as a polynomial interpolation using polynomial basis functions. The evaluation of polynomial and spline curve fitting models showed a respective divergence (test error) of 8% and 0.02% from the physically measured power consumption. The precisions of the instruments used for the physical measurements have been modeled as intervals. We have been able to model the power consumption of the RF device operating at 5MHz using homotopy between 2 continuous power consumptions of the RF device operating at the bandwidths 3MHz and 10MHz.
Abstract: This paper applies fuzzy AHP to evaluate the service
quality of online auction. Service quality is a composition of various
criteria. Among them many intangible attributes are difficult to
measure. This characteristic introduces the obstacles for respondents
on reply in the survey. So as to overcome this problem, we invite
fuzzy set theory into the measurement of performance and use AHP in
obtaining criteria. We found the most concerned dimension of service
quality is Transaction Safety Mechanism and the least is Charge Item.
Other criteria such as information security, accuracy and information
are too vital.
Abstract: Herein, the organic semiconductor methyl orange
(MO), is investigated for the first time for its electronic applications.
For this purpose, Al/MO/n-Si heterojunction is fabricated through
economical cheap and simple “drop casting” technique. The currentvoltage
(I-V) measurements of the device are made at room
temperature under dark conditions. The I-V characteristics of
Al/MO/n-Si junction exhibits asymmetrical and rectifying behavior
that confirms the formation of diode. The diode parameters such as
rectification ratio (RR), turn on voltage (Vturn on), reverse saturation
current (I0), ideality factor (n), barrier height ( b
f ), series resistance
(Rs) and shunt resistance (Rsh) are determined from I-V curves using
Schottky equations. These values of these parameters are also
extracted and verified by applying Cheung’s functions. The
conduction mechanisms are explained from the forward bias I-V
characteristics using the power law.
Abstract: This study aims at providing empirical evidence on a
comparison of two equity valuation models: (1) the dividend discount
model (DDM) and (2) the residual income model (RIM), in
estimating equity values of Thai firms during 1995-2004. Results
suggest that DDM and RIM underestimate equity values of Thai
firms and that RIM outperforms DDM in predicting cross-sectional
stock prices. Results on regression of cross-sectional stock prices on
the decomposed DDM and RIM equity values indicate that book
value of equity provides the greatest incremental explanatory power,
relative to other components in DDM and RIM terminal values,
suggesting that book value distortions resulting from accounting
procedures and choices are less severe than forecast and
measurement errors in discount rates and growth rates.
We also document that the incremental explanatory power of book
value of equity during 1998-2004, representing the information
environment under Thai Accounting Standards reformed after the
1997 economic crisis to conform to International Accounting
Standards, is significantly greater than that during 1995-1996,
representing the information environment under the pre-reformed
Thai Accounting Standards. This implies that the book value
distortions are less severe under the 1997 Reformed Thai Accounting
Standards than the pre-reformed Thai Accounting Standards.
Abstract: Segmentation and quantification of stenosis is an
important task in assessing coronary artery disease. One of the main
challenges is measuring the real diameter of curved vessels.
Moreover, uncertainty in segmentation of different tissues in the
narrow vessel is an important issue that affects accuracy. This paper
proposes an algorithm to extract coronary arteries and measure the
degree of stenosis. Markovian fuzzy clustering method is applied to
model uncertainty arises from partial volume effect problem. The
algorithm employs: segmentation, centreline extraction, estimation of
orthogonal plane to centreline, measurement of the degree of
stenosis. To evaluate the accuracy and reproducibility, the approach
has been applied to a vascular phantom and the results are compared
with real diameter. The results of 10 patient datasets have been
visually judged by a qualified radiologist. The results reveal the
superiority of the proposed method compared to the Conventional
thresholding Method (CTM) on both datasets.
Abstract: Oxygen transfer, the process by which oxygen is
transferred from the gaseous to liquid phase, is a vital part of the
waste water treatment process. Because of low solubility of
oxygen and consequent low rate of oxygen transfer, sufficient
oxygen to meet the requirement of aerobic waste does not enter
through normal surface air water interface. Many theories have
come up in explaining the mechanism of gas transfer and
absorption of non-reacting gases in a liquid, of out of which, Two
film theory is important. An exiting mathematical model
determines approximate value of Overall Gas Transfer coefficient.
The Overall Gas Transfer coefficient, in case of Penetration theory,
is 1.13 time more than that obtained in case of Two film theory.
The difference is due to the difference in assumptions in the two
theories.
The paper aims at development of mathematical model which
determines the value of Overall Gas Transfer coefficient with
greater accuracy than the existing model.
Abstract: Quality evaluation of an image is an important task in image processing applications. In case of image compression, quality of decompressed image is also the criterion for evaluation of given coding scheme. In the process of compression -decompression various artifacts such as blocking artifacts, blur artifact, ringing or edge artifact are observed. However quantification of these artifacts is a difficult task. We propose here novel method to quantify blur and ringing artifact in an image.
Abstract: The excellent suitability of the externally excited synchronous
machine (EESM) in automotive traction drive applications
is justified by its high efficiency over the whole operation range and
the high availability of materials. Usually, maximum efficiency is
obtained by modelling each single loss and minimizing the sum of all
losses. As a result, the quality of the optimization highly depends on
the precision of the model. Moreover, it requires accurate knowledge
of the saturation dependent machine inductances. Therefore, the
present contribution proposes a method to minimize the overall losses
of a salient pole EESM and its inverter in steady state operation based
on measurement data only. Since this method does not require any
manufacturer data, it is well suited for an automated measurement
data evaluation and inverter parametrization. The field oriented control
(FOC) of an EESM provides three current components resp. three
degrees of freedom (DOF). An analytic minimization of the copper
losses in the stator and the rotor (assuming constant inductances) is
performed and serves as a first approximation of how to choose the
optimal current reference values. After a numeric offline minimization
of the overall losses based on measurement data the results are
compared to a control strategy that satisfies cos (ϕ) = 1.
Abstract: This paper proposes the stochastic tabu search (STS)
for improving the measurement scheme for power system state
estimation. If the original measured scheme is not observable, the
additional measurements with minimum number of measurements are
added into the system by STS so that there is no critical measurement
pair. The random bit flipping and bit exchanging perturbations are
used for generating the neighborhood solutions in STS. The Pδ
observable concept is used to determine the network observability.
Test results of 10 bus, IEEE 14 and 30 bus systems are shown that
STS can improve the original measured scheme to be observable
without critical measurement pair. Moreover, the results of STS are
superior to deterministic tabu search (DTS) in terms of the best
solution hit.
Abstract: Hexapod Machine Tool (HMT) is a parallel robot
mostly based on Stewart platform. Identification of kinematic
parameters of HMT is an important step of calibration procedure. In
this paper an algorithm is presented for identifying the kinematic
parameters of HMT using inverse kinematics error model. Based on
this algorithm, the calibration procedure is simulated. Measurement
configurations with maximum observability are decided as the first
step of this algorithm for a robust calibration. The errors occurring in
various configurations are illustrated graphically. It has been shown
that the boundaries of the workspace should be searched for the
maximum observability of errors. The importance of using
configurations with sufficient observability in calibrating hexapod
machine tools is verified by trial calibration with two different
groups of randomly selected configurations. One group is selected to
have sufficient observability and the other is in disregard of the
observability criterion. Simulation results confirm the validity of the
proposed identification algorithm.
Abstract: The new idea of this research is application of a new fault detection and isolation (FDI) technique for supervision of sensor networks in transportation system. In measurement systems, it is necessary to detect all types of faults and failures, based on predefined algorithm. Last improvements in artificial neural network studies (ANN) led to using them for some FDI purposes. In this paper, application of new probabilistic neural network features for data approximation and data classification are considered for plausibility check in temperature measurement. For this purpose, two-phase FDI mechanism was considered for residual generation and evaluation.
Abstract: An improved topology of a voltage-fed quasi-resonant
soft switching LCrCdc series-parallel half bridge inverter with a constant-frequency for electronic ballast applications is proposed in this paper. This new topology introduces a low-cost solution to
reduce switching losses and circuit rating to achieve high-efficiency
ballast. Switching losses effect on ballast efficiency is discussed
through experimental point of view. In this discussion, an improved
topology in which accomplishes soft switching operation over a wide
power regulation range is proposed. The proposed structure uses reverse recovery diode to provide better operation for the ballast system. A symmetrical pulse wide modulation (PWM) control scheme is implemented to regulate a wide range of out-put power.
Simulation results are kindly verified with the experimental
measurements obtained by ballast-lamp laboratory prototype. Different load conditions are provided in order to clarify the
performance of the proposed converter.
Abstract: In present work the problem of the ITER fusion
plasma neutron source parameter reconstruction using only the
Vertical Neutron Camera data was solved. The possibility of neutron
source parameter reconstruction was estimated by the numerical
simulations and the analysis of adequateness of mathematic model
was performed. The neutron source was specified in a parametric
form. The numerical analysis of solution stability with respect to data
distortion was done. The influence of the data errors on the
reconstructed parameters is shown:
• is reconstructed with errors less than 4% at all examined values
of δ (until 60%);
• is determined with errors less than 10% when δ do not overcome
5%;
• is reconstructed with relative error more than 10 %;
• integral intensity of the neutron source is determined with error
10% while δ error is less than 15%;
where -error of signal measurements, (R0,Z0), the plasma center
position,- /parameter of neutron source profile.
Abstract: Object Relational Databases (ORDB) are complex in
nature than traditional relational databases because they combine the
characteristics of both object oriented concepts and relational
features of conventional databases. Design of an ORDB demands
efficient and quality schema considering the structural, functional
and componential traits. This internal quality of the schema is
assured by metrics that measure the relevant attributes. This is
extended to substantiate the understandability, usability and
reliability of the schema, thus assuring external quality of the
schema. This work institutes a formalization of ORDB metrics;
metric definition, evaluation methodology and the calibration of the
metric. Three ORDB schemas were used to conduct the evaluation
and the formalization of the metrics. The metrics are calibrated using
content and criteria related validity based on the measurability,
consistency and reliability of the metrics. Nominal and summative
scales are derived based on the evaluated metric values and are
standardized. Future works pertaining to ORDB metrics forms the
concluding note.
Abstract: The paper presents an on-line recognition machine
(RM) for continuous/isolated, dynamic and static gestures that arise
in Flight Deck Officer (FDO) training. RM is based on generic pattern
recognition framework. Gestures are represented as templates using
summary statistics. The proposed recognition algorithm exploits temporal
and spatial characteristics of gestures via dynamic programming
and Markovian process. The algorithm predicts corresponding index
of incremental input data in the templates in an on-line mode.
Accumulated consistency in the sequence of prediction provides a
similarity measurement (Score) between input data and the templates.
The algorithm provides an intuitive mechanism for automatic detection
of start/end frames of continuous gestures. In the present paper,
we consider isolated gestures. The performance of RM is evaluated
using four datasets - artificial (W TTest), hand motion (Yang) and
FDO (tracker, vision-based ). RM achieves comparable results which
are in agreement with other on-line and off-line algorithms such as
hidden Markov model (HMM) and dynamic time warping (DTW).
The proposed algorithm has the additional advantage of providing
timely feedback for training purposes.
Abstract: Accurate assessment of the primary tumor response to
treatment is important in the management of breast cancer. This
paper introduces a new set of treatment evaluation indicators for
breast cancer cases based on the computational process of three
known metrics, the Euclidian, Hamming and Levenshtein distances.
The distance principals are applied to pairs of mammograms and/or
echograms, recorded before and after treatment, determining a
reference point in judging the evolution amount of the studied
carcinoma. The obtained numerical results are indeed very
transparent and indicate not only the evolution or the involution of
the tumor under treatment, but also a quantitative measurement of the
benefit in using the selected method of treatment.
Abstract: This study reports the preparation of soft magnetic ribbons of Fe-based amorphous alloys using the single-roller melt-spinning technique. Ribbon width varied from 142 mm to 213 mm and, with a thickness of approximately 22 μm 2 μm. The microstructure and magnetic properties of the ribbons were characterized by differential scanning calorimeter (DSC), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), and electrical resistivity measurements (ERM). The amorphous material properties dependence of the cooling rate and nozzle pressure have uneven surface in ribbon thicknesses are investigated. Magnetic measurement results indicate that some region of the ribbon exhibits good magnetic properties, higher saturation induction and lower coercivity. However, due to the uneven surface of 213 mm wide ribbon, the magnetic responses are not uniformly distributed. To understand the transformer magnetic performances, this study analyzes the measurements of a three-phase 2 MVA amorphous-cored transformer. Experimental results confirm that the transformer with a ribbon width of 142 mm has better magnetic properties in terms of lower core loss, exciting power, and audible noise.
Abstract: This paper deals with a novel approach of power
transformers diagnostics. This approach identifies the exact location
and the range of a fault in the transformer and helps to reduce
operation costs related to handling of the faulty transformer, its
disassembly and repair. The advantage of the approach is a
possibility to simulate healthy transformer and also all faults, which
can occur in transformer during its operation without its
disassembling, which is very expensive in practice. The approach is
based on creating frequency dependent impedance of the transformer
by sweep frequency response analysis measurements and by 3D FE
parametrical modeling of the fault in the transformer. The parameters
of the 3D FE model are the position and the range of the axial short
circuit. Then, by comparing the frequency dependent impedances of
the parametrical models with the measured ones, the location and the
range of the fault is identified. The approach was tested on a real
transformer and showed high coincidence between the real fault and
the simulated one.
Abstract: Cheating on standardized tests has been a major
concern as it potentially minimizes measurement precision. One
major way to reduce cheating by collusion is to administer multiple
forms of a test. Even with this approach, potential collusion is still
quite large. A Latin-square treatment structure for distributing
multiple forms is proposed to further reduce the colluding potential.
An index to measure the extent of colluding potential is also
proposed. Finally, with a simple algorithm, the various Latin-squares
were explored to find the best structure to keep the colluding
potential to a minimum.
Abstract: Thermal load calculations have been performed for
multi-layered walls that are composed of three different parts; a
common (sand and cement) plaster, and two types of locally
produced soft and hard bricks. The masonry construction of these
layered walls was based on concrete-backed stone masonry made of
limestone bricks joined by mortar. These multilayered walls are
forming the outer walls of the building envelope of a typical Libyan
house. Based on the periodic seasonal weather conditions, within the
Libyan cost region during summer and winter, measured thermal
conductivity values were used to implement such seasonal variation
of heat flow and the temperature variations through the walls. The
experimental measured thermal conductivity values were obtained
using the Hot Disk technique. The estimation of the thermal
resistance of the wall layers ( R-values) is based on measurements
and calculations. The numerical calculations were done using a
simplified analytical model that considers two different wall
constructions which are characteristics of such houses. According to
the obtained results, the R-values were quite low and therefore,
several suggestions have been proposed to improve the thermal
loading performance that will lead to a reasonable human comfort
and reduce energy consumption.