Abstract: The modified Arcan fixture was used in order to
investigate the mixed mode fracture properties of high strength steel
butt weld through experimental and numerical analysis. The fixture
consisted of a central section with "butterfly-shaped" specimen that
had central crack. The specimens were under pure mode I (opening),
pure mode II (shearing) and all in plane mixed mode loading angles
starting from 0 to 90 degrees. The geometric calibration factors were
calculated with the aid of finite element analysis for various loading
mode and different crack length (0.45≤ a/w ≤0.55) and the critical
fracture loads obtained experimentally. The critical fracture
toughness (KIC & KIIC) estimated with experimental and numerical
analysis under mixed mode loading conditions.
Abstract: It is known that the heart interacts with and adapts to its venous and arterial loading conditions. Various experimental studies and modeling approaches have been developed to investigate the underlying mechanisms. This paper presents a model of the left ventricle derived based on nonlinear stress-length myocardial characteristics integrated over truncated ellipsoidal geometry, and second-order dynamic mechanism for the excitation-contraction coupling system. The results of the model presented here describe the effects of the viscoelastic damping element of the electromechanical coupling system on the hemodynamic response. Different heart rates are considered to study the pacing effects on the performance of the left-ventricle against constant preload and afterload conditions under various damping conditions. The results indicate that the pacing process of the left ventricle has to take into account, among other things, the viscoelastic damping conditions of the myofilament excitation-contraction process. The effects of left ventricular dimensions on the hemdynamic response have been examined. These effects are found to be different at different viscoelastic and pacing conditions.
Abstract: The limit load carrying capacity of functionally
graded materials (FGM) circular plates subjected to an arbitrary
rotationally symmetric loading has been computed. It is provided that
the plate material behaves rigid perfectly plastic and obeys either the
Square or the Tresca yield criterion. To this end the upper and lower
bound principles of limit analysis are employed to determine the
exact value for the limiting load. The correctness of the result are
verified and finally limiting loads for two examples namely; through
radius and through thickness FGM circular plates with simply
supported edges are calculated, respectively and moreover, the values
of critical loading factor are determined.
Abstract: Intradiscal and intervertebral pressure transducers
were developed. They were used to map the pressures in the nucleus
and within the annulus of the human spinal segments. Their stressrelaxation
were recorded over a period of time for nucleus
pressure, applied load, and peripherial strain against time. The
results show that for normal discs, pressures in the nucleus are
viscoelastic in nature with the applied compressive load.
Mechanical strains which develop around the periphery of the
vertebral body are also viscoelastic with the applied compressive
load. Applied compressive load against time also shows viscoelastic
behavior. However, annulus does not respond viscoelastically with
the applied load. It showed a linear response to compressive loading.
Abstract: Development, calibration and validation of a threedimensional
model of the Legform impactor for pedestrian crash with
bumper are presented. Lower limb injury is becoming an increasingly
important concern in vehicle safety for both occupants and
pedestrians. In order to prevent lower extremity injuries to a
pedestrian when struck by a car, it is important to elucidate the
loadings from car front structures on the lower extremities and the
injury mechanism caused by these loadings. An impact test
procedure with a legform addressing lower limb injuries in car
pedestrian accidents has been proposed by EEVC/WG17. In this
study a modified legform impactor is introduced and validated
against EEVC/WG17 criteria. The finite element model of this
legform is developed using LS-DYNA software. Total mass of
legform impactor is 13.4 kg.Technical specifications including the
mass and location of the center of gravity and moment of inertia
about a horizontal axis through the respective centre of gravity in
femur and tibia are determined. The obtained results of legform
impactor static and dynamic tests are as specified in the
EEVC/WG17.
Abstract: The aim of this study was to trace the effects of growth environment on the behaviour of fattening pigs in the farm and outside it. Behavioral manifestations of pigs reared in pens with enriched environment (A lot, n: 22) were different from those of pigs reared in pens with arid environment (B lot, n: 17) in shelter and when the movement to be loaded. Pigs of B lot spent more time on the move (31%) compared to group A pigs (13%), and manifested more aggressive behavior when they were loaded. Salivary cortisol levels also showed high values for pigs in B lot after being removed from their growth environment, as compared to its concentration for A lot pigs. The enriched environment for pigs may determine different responses of behavior. Pigs raised in arid environment, were easier to loaded than pigs reared in enriched environment, but they responded to mixing and loading stress, through increases in cortisol concentrations and impaired behavioral manifestations.
Abstract: ELS is an important ground based hardware in the
loop simulator used for aerodynamics torque loading experiments
of the actuators under test. This work focuses on improvement of the
transient response of torque controller with parameters uncertainty
of Electrical Load Simulator (ELS).The parameters of load simulator
are estimated online and the model is updated, eliminating the model
error and improving the steady state torque tracking response of
torque controller. To improve the Transient control performance the
gain of robust term of SMC is updated online using fuzzy logic
system based on the amount of uncertainty in parameters of load
simulator. The states of load simulator which cannot be measured
directly are estimated using luenberger observer with update of new
estimated parameters. The stability of the control scheme is verified
using Lyapunov theorem. The validity of proposed control scheme is
verified using simulations.
Abstract: Base on extenics theory, the statistical physical and mechanical properties from laboratory experiments are used to evaluate the bearing capacity of lateritic soil foundation. The properties include water content, bulk density, liquid limit, cohesion, and so on. The matter-element and the dependent function are defined. Then the synthesis dependent degree and the final grade index are calculated. The results show that predicted outcomes can be matched with the in-situ test data, and a evaluate grade associate with bearing capacity can be deduced. The results provide guidance to assess and determine the bearing capacity grade of lateritic soil foundation.
Abstract: Bicycle configuration is not as large as those of motorcycles or automobiles, while it indeed composes a complicated dynamic system. People-s requirements on comfortability, controllability and safety grow higher as the research and development technologies improve. The shock absorber affects the vehicle suspension performances enormously. The absorber takes the vibration energy and releases it at a suitable time, keeping the wheel under a proper contact condition with road surface, maintaining the vehicle chassis stability. Suspension design for mountain bicycles is more difficult than that of city bikes since it encounters dynamic variations on road and loading conditions. Riders need a stiff damper as they exert to tread on the pedals when climbing, while a soft damper when they descend downhill. Various switchable shock absorbers are proposed in markets, however riders have to manually switch them among soft, hard and lock positions. This study proposes a novel design of the bicycle shock absorber, which provides automatic smooth tuning of the damping coefficient, from a predetermined lower bound to theoretically unlimited. An automatic quick releasing valve is involved in this design so that it can release the peak pressure when the suspension fork runs into a square-wave type obstacle and prevent the chassis from damage, avoiding the rider skeleton from injury. This design achieves the automatic tuning process by innovative plunger valve and fluidic passage arrangements without any electronic devices. Theoretical modelling of the damper and spring are established in this study. Design parameters of the valves and fluidic passages are determined. Relations between design parameters and shock absorber performances are discussed in this paper. The analytical results give directions to the shock absorber manufacture.
Abstract: Intermittent aeration process can be easily applied on
the existing activated sludge system and is highly reliable against the loading changes. It can be operated in a relatively simple way as well.
Since the moving-bed biofilm reactor method processes pollutants by attaching and securing the microorganisms on the media, the process
efficiency can be higher compared to the suspended growth biological
treatment process, and can reduce the return of sludge. In this study,
the existing intermittent aeration process with alternating flow being
applied on the oxidation ditch is applied on the continuous flow stirred tank reactor with advantages from both processes, and we would like
to develop the process to significantly reduce the return of sludge in the clarifier and to secure the reliable quality of treated water by
adding the moving media. Corresponding process has the appropriate
form as an infrastructure based on u- environment in future u- City and
is expected to accelerate the implementation of u-Eco city in conjunction with city based services. The system being conducted in a
laboratory scale has been operated in HRT 8hours except for the final
clarifier and showed the removal efficiency of 97.7 %, 73.1 % and 9.4
% in organic matters, TN and TP, respectively with operating range of
4hour cycle on system SRT 10days. After adding the media, the removal efficiency of phosphorus showed a similar level compared to
that before the addition, but the removal efficiency of nitrogen was
improved by 7~10 %. In addition, the solids which were maintained in
MLSS 1200~1400 at 25 % of media packing were attached all onto the
media, which produced no sludge entering the clarifier. Therefore, the
return of sludge is not needed any longer.
Abstract: Stainless steel has been employed in many
engineering applications ranging from pharmaceutical equipment to
piping in the nuclear reactors and storage to chemical products. In
this attempt, simulation of fatigue crack growth based on
experimental results of austenitic stainless steel 304L was presented
using AFGROW code when NASGRO mode laws adopted. Double
through crack at hole specimen is used in this investigation under
constant amplitude loading. Effect of mean stress is highlighted.
Results show that fatigue crack growth rate (FCGR) and fatigue life
were affected by maximum applied load and dimension of hole. An
equivalent of Paris law for this material was estimated.
Abstract: Solution for the complete removal of carbon
monoxide from the exhaust gases still poses a challenge to the
researchers and this problem is still under development. Modeling for
reduction of carbon monoxide is carried out using heterogeneous
reaction using low cost non-noble metal based catalysts for the
purpose of controlling emissions released to the atmosphere. A
simple one-dimensional model was developed for the monolith using
hopcalite catalyst. The converter is assumed to be an adiabatic
monolith operating under warm-up conditions. The effect of inlet gas
temperatures and catalyst loading on carbon monoxide reduction
during cold start period in the converter is analysed.
Abstract: Adhesively bonded joints are preferred over the
conventional methods of joining such as riveting, welding, bolting
and soldering. Some of the main advantages of adhesive joints
compared to conventional joints are the ability to join dissimilar
materials and damage-sensitive materials, better stress distribution,
weight reduction, fabrication of complicated shapes, excellent
thermal and insulation properties, vibration response and enhanced
damping control, smoother aerodynamic surfaces and an
improvement in corrosion and fatigue resistance. This paper presents
the behavior of adhesively bonded joints subjected to combined
thermal loadings, using the numerical methods. The joint
configuration considers aluminum as central adherend with six
different outer adherends including aluminum, steel, titanium, boronepoxy,
unidirectional graphite-epoxy and cross-ply graphite-epoxy
and epoxy-based adhesives. Free expansion of the joint in x
direction was permitted and stresses in adhesive layer and interfaces
calculated for different adherends.
Abstract: Recent trends in building constructions in Libya are
more toward tall (high-rise) building projects. As a consequence, a
better estimation of the lateral loading in the design process is
becoming the focal of a safe and cost effective building industry. Byin-
large, Libya is not considered a potential earthquake prone zone,
making wind is the dominant design lateral loads. Current design
practice in the country estimates wind speeds on a mere random
bases by considering certain factor of safety to the chosen wind
speed. Therefore, a need for a more accurate estimation of wind
speeds in Libya was the motivation behind this study. Records of
wind speed data were collected from 22 metrological stations in
Libya, and were statistically analysed. The analysis of more than four
decades of wind speed records suggests that the country can be
divided into four zones of distinct wind speeds. A computer “survey"
program was manipulated to draw design wind speeds contour map
for the state of Libya.
The paper presents the statistical analysis of Libya-s recorded
wind speed data and proposes design wind speed values for a 50-year
return period that covers the entire country.
Abstract: Estimation of voltage stability based on optimal
filtering method is presented. PV curve is used as a tool for voltage stability analysis. Dynamic voltage stability estimation is done by
using particle filter method. Optimum value (nose point) of PV curve can be estimated by estimating parameter of PV curve equation
optimal value represents critical voltage and
condition at specified point of measurement. Voltage stability is then estimated by analyzing loading margin condition c stimating equation. This
maximum loading
ecified dynamically.
Abstract: Power cables are vulnerable to failure due to aging or
defects that occur with the passage of time under continuous
operation and loading stresses. PD detection and characterization
provide information on the location, nature, form and extent of the
degradation. As a result, PD monitoring has become an important
part of condition based maintenance (CBM) program among power
utilities. Online partial discharge (PD) localization of defect sources
in power cable system is possible using the time of flight method.
The information regarding the time difference between the main and
reflected pulses and cable length can help in locating the partial
discharge source along the cable length. However, if the length of
the cable is not known and the defect source is located at the extreme
ends of the cable or in the middle of the cable, then double ended
measurement is required to indicate the location of PD source. Use of
multiple sensors can also help in discriminating the cable PD or local/
external PD. This paper presents the experience and results from
online partial discharge measurements conducted in the laboratory
and the challenges in partial discharge source localization.
Abstract: Self-Excited Induction Generator (SEIG) builds up voltage while it enters in its magnetic saturation region. Due to non-linear magnetic characteristics, the performance analysis of SEIG involves cumbersome mathematical computations. The dependence of air-gap voltage on saturated magnetizing reactance can only be established at rated frequency by conducting a laboratory test commonly known as synchronous run test. But, there is no laboratory method to determine saturated magnetizing reactance and air-gap voltage of SEIG at varying speed, terminal capacitance and other loading conditions. For overall analysis of SEIG, prior information of magnetizing reactance, generated frequency and air-gap voltage is essentially required. Thus, analytical methods are the only alternative to determine these variables. Non-existence of direct mathematical relationship of these variables for different terminal conditions has forced the researchers to evolve new computational techniques. Artificial Neural Networks (ANNs) are very useful for solution of such complex problems, as they do not require any a priori information about the system. In this paper, an attempt is made to use cascaded neural networks to first determine the generated frequency and magnetizing reactance with varying terminal conditions and then air-gap voltage of SEIG. The results obtained from the ANN model are used to evaluate the overall performance of SEIG and are found to be in good agreement with experimental results. Hence, it is concluded that analysis of SEIG can be carried out effectively using ANNs.
Abstract: Equilibrium and stability equations of a thin rectangular plate with length a, width b, and thickness h(x)=C1x+C2, made of functionally graded materials under thermal loads are derived based on the first order shear deformation theory. It is assumed that the material properties vary as a power form of thickness coordinate variable z. The derived equilibrium and buckling equations are then solved analytically for a plate with simply supported boundary conditions. One type of thermal loading, uniform temperature rise and gradient through the thickness are considered, and the buckling temperatures are derived. The influences of the plate aspect ratio, the relative thickness, the gradient index and the transverse shear on buckling temperature difference are all discussed.
Abstract: A numerical study is presented on buckling and post
buckling behaviour of laminated carbon fiber reinforced plastic
(CFRP) thin-walled cylindrical shells under axial compression using
asymmetric meshing technique (AMT). Asymmetric meshing
technique is a perturbation technique to introduce disturbance without
changing geometry, boundary conditions or loading conditions.
Asymmetric meshing affects predicted buckling load, buckling mode
shape and post-buckling behaviour. Linear (eigenvalue) and nonlinear
(Riks) analyses have been performed to study the effect of
asymmetric meshing in the form of a patch on buckling behaviour.
The reduction in the buckling load using Asymmetric meshing
technique was observed to be about 15%. An isolated dimple formed
near the bifurcation point and the size of which increased to reach a
stable state in the post-buckling region. The load-displacement curve
behaviour applying asymmetric meshing is quite similar to the curve
obtained using initial geometric imperfection in the shell model.
Abstract: There are only limited studies that directly correlate
the increase in reinforced concrete (RC) panel structural capacities in
resisting the blast loads with different RC panel structural properties
in terms of blast loading characteristics, RC panel dimensions, steel
reinforcement ratio and concrete material strength. In this paper,
numerical analyses of dynamic response and damage of the one-way
RC panel to blast loads are carried out using the commercial software
LS-DYNA. A series of simulations are performed to predict the blast
response and damage of columns with different level and magnitude
of blast loads. The numerical results are used to develop pressureimpulse
(P-I) diagrams of one-way RC panels. Based on the
numerical results, the empirical formulae are derived to calculate the
pressure and impulse asymptotes of the P-I diagrams of RC panels.
The results presented in this paper can be used to construct P-I
diagrams of RC panels with different concrete and reinforcement
properties. The P-I diagrams are very useful to assess panel capacities
in resisting different blast loads.