Abstract: This paper presents nonlinear elastic dynamic analysis
of 3-D semi-rigid steel frames including geometric and connection
nonlinearities. The geometric nonlinearity is considered by using
stability functions and updating geometric stiffness matrix. The
nonlinear behavior of the steel beam-to-column connection is
considered by using a zero-length independent connection element
comprising of six translational and rotational springs. The nonlinear
dynamic equilibrium equations are solved by the Newmark numerical
integration method. The nonlinear time-history analysis results are
compared with those of previous studies and commercial SAP2000
software to verify the accuracy and efficiency of the proposed
procedure.
Abstract: Analysis of reciprocating equipment piston rod leads
to nonlinear elastic-plastic deformation analysis of rod with initial
imperfection under axial dynamic load. In this paper a new and
effective model and analytical formulations are presented to evaluate
dynamic deformation and elastic-plastic stresses of reciprocating
machine piston rod. This new method has capability to account for
geometric nonlinearity, elastic-plastic deformation and dynamic
effects. Proposed method can be used for evaluation of piston rod
performance for various reciprocating machines under different
operation situations. Rod load curves and maximum allowable rod
load are calculated with presented method for a refinery type
reciprocating compressor. Useful recommendations and guidelines
for rod load, rod load reversal and rod drop monitoring are also
addressed.
Abstract: In this paper the development of a heat exchanger as a
pilot plant for educational purpose is discussed and the use of neural
network for controlling the process is being presented. The aim of the
study is to highlight the need of a specific Pseudo Random Binary
Sequence (PRBS) to excite a process under control. As the neural
network is a data driven technique, the method for data generation
plays an important role. In light of this a careful experimentation
procedure for data generation was crucial task. Heat exchange is a
complex process, which has a capacity and a time lag as process
elements. The proposed system is a typical pipe-in- pipe type heat
exchanger. The complexity of the system demands careful selection,
proper installation and commissioning. The temperature, flow, and
pressure sensors play a vital role in the control performance. The
final control element used is a pneumatically operated control valve.
While carrying out the experimentation on heat exchanger a welldrafted
procedure is followed giving utmost attention towards safety
of the system. The results obtained are encouraging and revealing
the fact that if the process details are known completely as far as
process parameters are concerned and utilities are well stabilized then
feedback systems are suitable, whereas neural network control
paradigm is useful for the processes with nonlinearity and less
knowledge about process. The implementation of NN control
reinforces the concepts of process control and NN control paradigm.
The result also underlined the importance of excitation signal
typically for that process. Data acquisition, processing, and
presentation in a typical format are the most important parameters
while validating the results.
Abstract: Multi-loop (De-centralized) Proportional-Integral-
Derivative (PID) controllers have been used extensively in process
industries due to their simple structure for control of multivariable
processes. The objective of this work is to design multiple-model
adaptive multi-loop PID strategy (Multiple Model Adaptive-PID)
and neural network based multi-loop PID strategy (Neural Net
Adaptive-PID) for the control of multivariable system. The first
method combines the output of multiple linear PID controllers,
each describing process dynamics at a specific level of operation.
The global output is an interpolation of the individual multi-loop
PID controller outputs weighted based on the current value of the
measured process variable. In the second method, neural network
is used to calculate the PID controller parameters based on the
scheduling variable that corresponds to major shift in the process
dynamics. The proposed control schemes are simple in structure with
less computational complexity. The effectiveness of the proposed
control schemes have been demonstrated on the CSTR process,
which exhibits dynamic non-linearity.
Abstract: Multi-residue analysis method for penicillins was
developed and validated in bovine muscle, chicken, milk, and flatfish.
Detection was based on liquid chromatography tandem mass
spectrometry (LC/MS/MS). The developed method was validated for
specificity, precision, recovery, and linearity. The analytes were
extracted with 80% acetonitrile and clean-up by a single
reversed-phase solid-phase extraction step. Six penicillins presented
recoveries higher than 76% with the exception of Amoxicillin
(59.7%). Relative standard deviations (RSDs) were not more than
10%. LOQs values ranged from 0.1 and to 4.5 ug/kg. The method was
applied to 128 real samples. Benzylpenicillin was detected in 15
samples and Cloxacillin was detected in 7 samples. Oxacillin was
detected in 2 samples. But the detected levels were under the MRL
levels for penicillins in samples.
Abstract: This study applies the sequential panel selection
method (SPSM) procedure proposed by Chortareas and Kapetanios
(2009) to investigate the time-series properties of energy
consumption in 50 US states from 1963 to 2009. SPSM involves the
classification of the entire panel into a group of stationary series and
a group of non-stationary series to identify how many and which
series in the panel are stationary processes. Empirical results obtained
through SPSM with the panel KSS unit root test developed by Ucar
and Omay (2009) combined with a Fourier function indicate that
energy consumption in all the 50 US states are stationary. The results
of this study have important policy implications for the 50 US states.
Abstract: The electromagnetic imaging of inhomogeneous
dielectric cylinders buried in a slab medium by transverse electric
(TE) wave illumination is investigated. Dielectric cylinders of
unknown permittivities are buried in second space and scattered a
group of unrelated waves incident from first space where the scattered
field is recorded. By proper arrangement of the various unrelated
incident fields, the difficulties of ill-posedness and nonlinearity are
circumvented, and the permittivity distribution can be reconstructed
through simple matrix operations. The algorithm is based on the
moment method and the unrelated illumination method. Numerical
results are given to demonstrate the capability of the inverse
algorithm. Good reconstruction is obtained even in the presence of
additive Gaussian random noise in measured data. In addition, the
effect of noise on the reconstruction result is also investigated.
Abstract: This paper describes a low-voltage and low-power
channel selection analog front end with continuous-time low pass
filters and highly linear programmable gain amplifier (PGA). The
filters were realized as balanced Gm-C biquadratic filters to achieve a
low current consumption. High linearity and a constant wide
bandwidth are achieved by using a new transconductance (Gm) cell.
The PGA has a voltage gain varying from 0 to 65dB, while
maintaining a constant bandwidth. A filter tuning circuit that requires
an accurate time base but no external components is presented.
With a 1-Vrms differential input and output, the filter achieves
-85dB THD and a 78dB signal-to-noise ratio. Both the filter and PGA
were implemented in a 0.18um 1P6M n-well CMOS process. They
consume 3.2mW from a 1.8V power supply and occupy an area of
0.19mm2.
Abstract: In this paper a new approach for transmission pricing
is presented. The main idea is voltage angle allocation, i.e.
determining the contribution of each contract on the voltage angle of
each bus. DC power flow is used to compute a primary solution for
angle decomposition. To consider the impacts of system non-linearity
on angle decomposition, the primary solution is corrected in different
iterations of decoupled Newton-Raphson power flow. Then, the
contribution of each contract on power flow of each transmission line
is computed based on angle decomposition. Contract-related flows
are used as a measure for “extent of use" of transmission network
capacity and consequently transmission pricing. The presented
approach is applied to a 4-bus test system and IEEE 30-bus test
system.
Abstract: This paper describes a study of geometrically
nonlinear free vibration of thin circular functionally graded (CFGP)
plates resting on Winkler elastic foundations. The material properties
of the functionally graded composites examined here are assumed to
be graded smoothly and continuously through the direction of the
plate thickness according to a power law and are estimated using the
rule of mixture. The theoretical model is based on the classical Plate
theory and the Von-Kármán geometrical nonlinearity assumptions.
An homogenization procedure (HP) is developed to reduce the
problem considered here to that of isotropic homogeneous circular
plates resting on Winkler foundation. Hamilton-s principle is applied
and a multimode approach is derived to calculate the fundamental
nonlinear frequency parameters which are found to be in a good
agreement with the published results. On the other hand, the
influence of the foundation parameters on the nonlinear fundamental
frequency has also been analysed.
Abstract: A 2.4GHz (RF) down conversion Gilbert Cell mixer,
implemented in a 0.18-μm CMOS technology with a 1.8V supply, is
presented. Current bleeding (charge injection) technique has been
used to increase the conversion gain and the linearity of the mixer.
The proposed mixer provides 10.75 dB conversion gain ( C G ) with
14.3mw total power consumption. The IIP3 and 1-dB compression
point of the mixer are 8dbm and -4.6dbm respectively, at 300 MHz
IF frequencies. Comparing the current design against the
conventional mixer design, demonstrates better performance in the
conversion gain, linearity, noise figure and port-to-port isolation.
Abstract: Carboneous catalytical methane decomposition is an
attractive process because it produces two valuable products:
hydrogen and carbon. Furthermore, this reaction does not emit any
green house or hazardous gases. In the present study, experiments
were conducted in a thermo gravimetric analyzer using Fluka 05120
as carboneous catalyst to analyze its effectiveness in methane
decomposition. Various temperatures and methane partial pressures
were chosen and carbon mass gain was observed as a function of
time. Results are presented in terms of carbon formation rate,
hydrogen production and catalytical activity. It is observed that there
is linearity in carbon deposition amount by time at lower reaction
temperature (780 °C). On the other hand, it is observed that carbon
and hydrogen formation rates are increased with increasing
temperature. Finally, we observed that the carbon formation rate is
highest at 950 °C within the range of temperatures studied.
Abstract: We propose an all optical flip-flop circuit composedof two Silicon-on-insulator microring resonators coupled to straightwaveguides by exploiting the optical bistability behavior due to thenonlinear Kerr effect. We used the transfer matrix analysis toinvestigate continuous wave propagation through microrings, as wellwe considered the nonlinear switching characteristics of an opticaldevice using a double-coupler silicon ring resonator in presence ofthe Kerr nonlinearity, thus obtaining the bistability behavior of theoutput port, the drop port and also inside the silicon microringresonator. It is shown that the bistability behavior depends on thecontrol of the input wavelength.KeywordsAll optical flip-flops, Kerr effect, microringresonator, optical bistability.
Abstract: Many recent electrophysiological studies have
revealed the importance of investigating meditation state in order to
achieve an increased understanding of autonomous control of
cardiovascular functions. In this paper, we characterize heart rate
variability (HRV) time series acquired during meditation using
nonlinear dynamical parameters. We have computed minimum
embedding dimension (MED), correlation dimension (CD), largest
Lyapunov exponent (LLE), and nonlinearity scores (NLS) from HRV
time series of eight Chi and four Kundalini meditation practitioners.
The pre-meditation state has been used as a baseline (control) state to
compare the estimated parameters. The chaotic nature of HRV during
both pre-meditation and meditation is confirmed by MED. The
meditation state showed a significant decrease in the value of CD and
increase in the value of LLE of HRV, in comparison with premeditation
state, indicating a less complex and less predictable nature
of HRV. In addition, it was shown that the HRV of meditation state
is having highest NLS than pre-meditation state. The study indicated
highly nonlinear dynamic nature of cardiac states as revealed by
HRV during meditation state, rather considering it as a quiescent
state.
Abstract: Complex statistical analysis of stresses in concrete
slab of the real type of rigid pavement is performed. The
computational model of the pavement is designed as a spatial (3D) model, is based on a nonlinear variant of the finite element method
that respects the structural nonlinearity, enables to model different arrangement of joints, and the entire model can be loaded by the
thermal load. Interaction of adjacent slabs in joints and contact of the slab and the subsequent layer are modeled with help of special
contact elements. Four concrete slabs separated by transverse and
longitudinal joints and the additional subgrade layers and soil to the depth of about 3m are modeled. The thickness of individual layers,
physical and mechanical properties of materials, characteristics of
joints, and the temperature of the upper and lower surface of slabs are supposed to be random variables. The modern simulation technique
Updated Latin Hypercube Sampling with 20 simulations is used for statistical analysis. As results, the estimates of basic statistics of the
principal stresses s1 and s3 in 53 points on the upper and lower surface of the slabs are obtained.
Abstract: This paper describes dynamic analysis using proposed
fast finite element method for a shock absorbing structure including a
sponge. The structure is supported by nonlinear concentrated springs.
The restoring force of the spring has cubic nonlinearity and linear
hysteresis damping. To calculate damping properties for the structures
including elastic body and porous body, displacement vectors as
common unknown variable are solved under coupled condition. Under
small amplitude, we apply asymptotic method to complex eigenvalue
problem of this system to obtain modal parameters. And then
expressions of modal loss factor are derived approximately. This
approach was proposed by one of the authors previously. We call this
method as Modal Strain and Kinetic Energy Method (MSKE method).
Further, using the modal loss factors, the discretized equations in
physical coordinate are transformed into the nonlinear ordinary
coupled equations using normal coordinate corresponding to linear
natural modes. This transformation yields computation efficiency. As
a numerical example of a shock absorbing structures, we adopt double
skins with a sponge. The double skins are supported by nonlinear
concentrated springs. We clarify influences of amplitude of the input
force on nonlinear and chaotic responses.
Abstract: This paper presents a system for tracking the movement of laparoscopic instruments which is based on an orthogonal system of webcams and video image processing. The movements are captured with two webcams placed orthogonally inside of the physical trainer. On the image, the instruments were detected by using color markers placed on the distal tip of each instrument. The 3D position of the tip of the instrument within the work space was obtained by linear triangulation method. Preliminary results showed linearity and repeatability in the motion tracking with a resolution of 0.616 mm in each axis; the accuracy of the system showed a 3D instrument positioning error of 1.009 ± 0.101 mm. This tool is a portable and low-cost alternative to traditional tracking devices and a trustable method for the objective evaluation of the surgeon’s surgical skills.
Abstract: This paper describes vibration analysis using the finite
element method for a small earphone, especially for the diaphragm
shape with a low-rigidity. The viscoelastic diaphragm is supported by
multiple nonlinear concentrated springs with linear hysteresis
damping. The restoring forces of the nonlinear springs have cubic
nonlinearity. The finite elements for the nonlinear springs with
hysteresis are expressed and are connected to the diaphragm that is
modeled by linear solid finite elements in consideration of a complex
modulus of elasticity. Further, the discretized equations in physical
coordinates are transformed into the nonlinear ordinary coupled
equations using normal coordinates corresponding to the linear natural
modes. We computed the nonlinear stationary and non-stationary
responses due to the internal resonance between modes with large
amplitude in the nonlinear springs and elastic modes in the diaphragm.
The non-stationary motions are confirmed as the chaos due to the
maximum Lyapunov exponents with a positive number. From the time
histories of the deformation distribution in the chaotic vibration, we
identified nonlinear modal couplings.
Abstract: A behavioral model of a second order switchedcapacitor Sigma-Delta modulator is presented. The purpose of this work is the presentation of a behavioral model of a second order switched capacitor ΣΔ modulator considering (Error due to Clock Jitter, Thermal noise Amplifier Noise, Amplifier Slew-Rate, Non linearity of amplifiers, Gain error, Charge Injection, Clock Feedthrough, and Nonlinear on-resistance). A comparison between the use of MOS switches and the use transmission gate switches use is analyzed.
Abstract: A design flow of multi-standard down-conversion
CMOS mixers for three modern standards: Global System Mobile,
Digital Enhanced Cordless Telephone and Universal Mobile
Telecommunication Systems is presented. Three active mixer-s
structures are studied. The first is based on the Gilbert cell which
gives a tolerable noise figure and linearity with a low conversion
gain. The second and third structures use the current bleeding and
charge injection techniques in order to increase the conversion gain.
An improvement of about 2 dB of the conversion gain is achieved
without a considerable degradation of the other characteristics. The
models used for noise figure, conversion gain and IIP3 used are
studied. This study describes the nature of trade-offs inherent in such
structures and gives insights that help in identifying which structure
is better for given conditions.