Abstract: Universal modeling method well proven for industrial
compressors was applied for design of the high flow rate supersonic
stage. Results were checked by ANSYS CFX and NUMECA Fine
Turbo calculations. The impeller appeared to be very effective at
transonic flow velocities. Stator elements efficiency is acceptable at
design Mach numbers too. Their loss coefficient versus inlet flow
angle performances correlates well with Universal modeling
prediction. The impeller demonstrates ability of satisfactory operation
at design flow rate. Supersonic flow behavior in the impeller inducer
at the shroud blade to blade surface Φ des deserves additional study.
Abstract: Wet scrubbers have found widespread use in cleaning
contaminated gas streams because of their ability to remove
particulates and based on the applications of scrubbing of marine
engine exhaust gases by spraying sea-water. In order to examine the
flow characteristics inside the scrubber, the model is designated with
flow properties of hot air and water sprayer. The flow dynamics of
evaporation of hot air by the injection of water droplets is the key
factor considered in this paper. The flow behavior inside the scrubber
was investigated from the previous works and to sum up the
evaporation rate with respect to the concentration of water droplets are
predicted to bring out the competent modelling. The numerical
analysis using CFD facilitates in understanding the problem better and
empathies the behavior of the model over its entire operating envelope.
Abstract: The computational fluid dynamics (CFD) study of
stirred tank with the air-water interface are carried out in the presence
of different types of the impeller and with or without baffles. A
multiple reference frame (MRF) approach with the volume of fluid
(VOF) method is used to capture the air-water interface. The RANS
(Reynolds Averaged Navier-Stokes) equations with k-ε turbulence
model are solved to predict the flow behavior of water and air phase
which are treated as a different phases. The predicted results have
shown that the VOF method is able to capture the interface in the
unbaffled tank. While, the VOF method is showing an unfeasible
results in the baffled tank with high rotational impeller speed. For
continuous stirred tank, the air-water interface is disturbed by the
inflow and the level of water is also increased with time.
Abstract: This paper investigates the natural convection heat transfer performance in a complex-wavy-wall cavity filled with power-law fluid. In performing the simulations, the continuity, Cauchy momentum and energy equations are solved subject to the Boussinesq approximation using a finite volume method. The simulations focus specifically on the effects of the flow behavior index in the power-law model and the Rayleigh number on the flow streamlines, isothermal contours and mean Nusselt number within the cavity. The results show that pseudoplastic fluids have a better heat transfer performance than Newtonian or dilatant fluids. Moreover, it is shown that for Rayleigh numbers greater than Ra=103, the mean Nusselt number has a significantly increase as the flow behavior index is decreased.
Abstract: This numerical study aims to develop a coupled,
passive and active control strategy of the flow around a cylinder of
diameter D, and Re=4000. The strategy consists to put a cylindrical
rod in front of a deforming cylinder. The quasi- elliptical deformation
of cylinder follow a sinusoidal law in order to reduce the drag force.
To analyze the evolution of unsteady vortices, the Large Eddy
Simulation approach is used in this 2D simulation, carried out using
ANSYS – Fluent. The movement of deformation is reproduced using
an internal subroutine, introduced in the form of a User Defined
Function UDF. Two diameters of the rod were tested for a rod placed
at a distance L = 3 ×d, with an amplitudes of deformation A = 5%, A
= 25% and A = 50% of the cylinder diameter, the frequency of
deformation take the values fd = 1fn, 5fn and 8fn, which fn
represents the naturel vortex shedding frequency. The results show
substantial changes in the flow behavior and for a rod of 6mm (1%
D) with amplitude A = 25%, and with a 2fn frequency, drag
reduction of 60% was recorded.
Abstract: This study involves numerical simulation of the flow
around a NACA2415 airfoil, with a 18° angle of attack, and flow
separation control using a rod, It involves putting a cylindrical rod -
upstream of the leading edge- in vertical translation movement in
order to accelerate the transition of the boundary layer by interaction
between the rod wake and the boundary layer. The viscous, nonstationary
flow is simulated using ANSYS FLUENT 13. The rod
movement is reproduced using the dynamic mesh technique and an
in-house developed UDF (User Define Function). The frequency
varies from 75 to 450 Hz and the considered amplitudes are 2%, and
3% of the foil chord. The frequency chosen closed to the frequency
of separation. Our results showed a substantial modification in the
flow behavior and a maximum drag reduction of 61%.
Abstract: The main purpose of this work is to experimentally investigate the effect of pipe orientation on two phase flow phenomenon. Flow pattern, void fraction and two phase pressure drop is measured in a polycarbonate pipe with an inside diameter of 12.7mm for inclination angles ranging from -20o to +20o using air-water fluid combination. The experimental data covers all flow patterns and the entire range of void fraction typically observed in two phase flow. The effect of pipe orientation on void fraction and two phase pressure drop is justified with reference to the change in flow structure and two phase flow behavior. In addition to this, the top performing void fraction and two phase pressure drop correlations available in the literature are presented and their performance is assessed against the experimental data in the present study and that available in the literature.
Abstract: This study involves a numerical simulation of the flow around a NACA2415 airfoil, with a 15°angle of attack, and flow separation control using a rod, It reposes inputting a cylindrical rod upstream of the leading edge in order to accelerate the transition of the boundary layer by interaction between the rod wake and the boundary layer. The viscous, non-stationary flow is simulated using ANSYS FLUENT 13. Our results showed a substantial modification in the flow behavior and a maximum drag reduction of 51%.
Abstract:
This research studied the influence of delta wing and delta winglet vortex generators on air flow characteristic. Normally, the vortex generator has been used for enhancing the heat transfer performance by promote the helical flow of air stream. The vortex generator was setup in the wind tunnel and the flow pattern of air stream passing the vortex generator was observed by using smoke generator. The Reynolds number of air stream was between 30,000 and 80,000. It is found that the delta winglet having 20mm fin height and 30 degree of air stream contact angle generates the maximum helical flow of air stream.
Abstract: Different approaches for heating\cooling of stirred tanks, coils and jackets, are investigated using computational fluid dynamics (CFD).A time-dependant sliding mesh approach is applied to simulate the flow in both conditions. The investigations are carried out under the turbulent flow conditions for a Rushton impeller and heating elements are considered isothermal. The flow behavior and temperature distribution are studied for each case and heat transfer coefficient is calculated. Results show different velocity profiles for each case. Unsteady temperature distribution is not similar for different cases .In the case of the coiled stirred vessel more uniform temperature and higher heat transfer coefficient is resulted.
Abstract: In this article, the flow behavior around a NACA 0012 airfoil which is oscillating with different Reynolds numbers and in various amplitudes has been investigated numerically. Numerical simulations have been performed with ANSYS software. First, the 2- D geometry has been studied in different Reynolds numbers and angles of attack with various numerical methods in its static condition. This analysis was to choose the best turbulent model and comparing the grids to have the optimum one for dynamic simulations. Because the analysis was to study the blades of wind turbines, the Reynolds numbers were not arbitrary. They were in the range of 9.71e5 to 22.65e5. The angle of attack was in the range of -41.81° to 41.81°. By choosing the forward wind speed as the independent parameter, the others like Reynolds and the amplitude of the oscillation would be known automatically. The results show that the SST turbulent model is the best choice that leads the least numerical error with respect the experimental ones. Also, a dynamic stall phenomenon is more probable at lower wind speeds in which the lift force is less.
Abstract: Series of experimental tests were conducted on a
section of a 660 kW wind turbine blade to measure the pressure
distribution of this model oscillating in plunging motion. In order to
minimize the amount of data required to predict aerodynamic loads
of the airfoil, a General Regression Neural Network, GRNN, was
trained using the measured experimental data. The network once
proved to be accurate enough, was used to predict the flow behavior
of the airfoil for the desired conditions.
Results showed that with using a few of the acquired data, the
trained neural network was able to predict accurate results with
minimal errors when compared with the corresponding measured
values. Therefore with employing this trained network the
aerodynamic coefficients of the plunging airfoil, are predicted
accurately at different oscillation frequencies, amplitudes, and angles
of attack; hence reducing the cost of tests while achieving acceptable
accuracy.
Abstract: The influence of lactulose and inulin on rheological
properties of fermented milk during storage was studied.Pasteurized
milk, freeze-dried starter culture Bb-12 (Bifidobacterium lactis, Chr.
Hansen, Denmark), inulin – RAFTILINE®HP (ORAFI, Belgium) and
syrup of lactulose (Duphalac®, the Netherlands) were used for
experiments. The fermentation process was realized at 37 oC for 16
hours and the storage of products was provided at 4 oC for 7 days.
Measurements were carried out by BROOKFIELD standard methods
and the flow curves were described by Herschel-Bulkley model.
The results of dispersion analysis have shown that both the
concentration of prebiotics (p=0.04
Abstract: The present study deals with the modeling and simulation of flow through an annular reactor at different hydrodynamic conditions using computational fluid dynamics (CFD) to investigate the flow behavior. CFD modeling was utilized to predict velocity distribution and average velocity in the annular geometry. The results of CFD simulations were compared with the mathematically derived equations and already developed correlations for validation purposes. CFD modeling was found suitable for predicting the flow characteristics in annular geometry under laminar flow conditions. It was observed that CFD also provides local values of the parameters of interest in addition to the average values for the simulated geometry.
Abstract: The paper investigates parallel channel instabilities of
natural circulation boiling water reactor. A thermal-hydraulic model
is developed to simulate two-phase flow behavior in the natural circulation boiling water reactor (NCBWR) with the incorporation of
ex-core components and recirculation loop such as steam separator, down-comer, lower-horizontal section and upper-horizontal section
and then, numerical analysis is carried out for parallel channel
instabilities of the reactor undergoing both in-phase and out-of-phase
modes of oscillations. To analyze the relative effect on stability of the reactor due to inclusion of various ex-core components and
recirculation loop, marginal stable point is obtained at a particular inlet enthalpy of the reactor core without the inclusion of ex-core
components and recirculation loop and then with the inclusion of the
same. Numerical simulations are also conducted to determine the
relative dominance between two modes of oscillations i.e. in-phase and out-of-phase. Simulations are also carried out when the channels
are subjected to asymmetric power distribution keeping the inlet enthalpy same.
Abstract: This paper presents the design, development and characterization of contractile water jet thruster (CWJT) for mini underwater robot. Instead of electric motor, this CWJT utilizes the Ionic Polymer Metal Composite (IPMC) as the actuator to generate the water jet. The main focus of this paper is to analyze the conceptual design of the proposed CWJT which would determine the thrust force value, jet flow behavior and actuator’s stress. Those thrust force and jet flow studies were carried out using Matlab/Simscape simulation software. The actuator stress had been analyzed using COSMOS simulation software. The results showed that there was no significant change for jet velocity at variable cross sectional nozzle area. However, a significant change was detected for jet velocity at different nozzle cross sectional area ratio which was up to 37%. The generated thrust force has proportional relation to the nozzle cross sectional area.
Abstract: Hydrocyclones flow field study is conducted by performing a parametric study. Effect of cone angle on deoiling hydrocyclones flow behaviour is studied in this research. Flow field of hydrocyclone is obtained by three-dimensional simulations with OpenFOAM code. Because of anisotropic behaviour of flow inside hydrocyclones LES is a suitable method to predict the flow field since it resolves large scales and model isotropic small scales. Large eddy simulation is used to predict the flow behavior of three different cone angles. Differences in tangential velocity and pressure distribution are reported in some figures.
Abstract: For many chemical and biological processes, the understanding of the mixing phenomenon and flow behavior in a stirred tank is of major importance. A three-dimensional numerical study was performed using the software Fluent, to study the flow field in a stirred tank with a Rushton turbine. In this work, we first studied the flow generated in the tank with a Rushton turbine. Then, we studied the effect of the variation of turbine’s submergence on the thermodynamic quantities defining the flow field. For that, four submergences were considered, while maintaining the same rotational speed (N =250rpm). This work intends to optimize the aeration performances of a Rushton turbine in a stirred tank.
Abstract: Interaction effects of xanthan gum (XG), carboxymethyl
cellulose (CMC), and locust bean gum (LBG) on the flow properties
of oil-in-water emulsions were investigated by a mixture design
experiment. Blends of XG, CMC and LBG were prepared according
to an augmented simplex-centroid mixture design (10 points) and used
at 0.5% (wt/wt) in the emulsion formulations. An appropriate
mathematical model was fitted to express each response as a function
of the proportions of the blend components that are able to
empirically predict the response to any blend of combination of the
components. The synergistic interaction effect of the ternary
XG:CMC:LBG blends at approximately 33-67% XG levels was
shown to be much stronger than that of the binary XG:LBG blend at
50% XG level (p < 0.05). Nevertheless, an antagonistic interaction
effect became significant as CMC level in blends was more than 33%
(p < 0.05). Yield stress and apparent viscosity (at 10 s-1) responses
were successfully fitted with a special quartic model while flow
behaviour index and consistency coefficient were fitted with a full
quartic model (R2
adjusted ≥ 0.90). This study found that a mixture
design approach could serve as a valuable tool in better elucidating
and predicting the interaction effects beyond the conventional twocomponent
blends.
Abstract: The effect of the blade tip geometry of a high pressure
gas turbine is studied experimentally and computationally for high
speed leakage flows. For this purpose two simplified models are
constructed, one models a flat tip of the blade and the second models
a cavity tip of the blade. Experimental results are obtained from a
transonic wind tunnel to show the static pressure distribution along
the tip wall and provide flow visualization. RANS computations
were carried to provide further insight into the mean flow behavior
and to calculate the discharge coefficient which is a measure of the
flow leaking over the tip. It is shown that in both geometries of tip
the flow separates over the tip to form a separation bubble. The
bubble is higher for the cavity tip while a complete shock wave
system of oblique waves ending with a normal wave can be seen for
the flat tip. The discharge coefficient for the flat tip shows less
dependence on the pressure ratio over the blade tip than the cavity
tip. However, the discharge coefficient for the cavity tip is lower than
that of the flat tip, showing a better ability to reduce the leakage flow
and thus increase the turbine efficiency.