Abstract: In this study four Holstein steers with rumen fistula
fed 7 kg of dry matter (DM) of diets differing in concentrate to
alfalfa hay ratios as 60:40, 70:30, 80:20, and 90:10 in a 4 × 4 latin
square design. The pH of the ruminal fluid was measured before
the morning feeding (0.0 h) to 8 h post feeding. In this study, a
two-layered feed-forward neural network trained by the
Levenberg-Marquardt algorithm was used for modelling of ruminal
pH. The input variables of the network were time, concentrate to
alfalfa hay ratios (C/F), non fiber carbohydrate (NFC) and neutral
detergent fiber (NDF). The output variable was the ruminal pH.
The modeling results showed that there was excellent agreement
between the experimental data and predicted values, with a high
determination coefficient (R2 >0.96). Therefore, we suggest using
these model-derived biological values to summarize continuously
recorded pH data.
Abstract: A multiphase harmonic load flow algorithm is developed based on backward/forward sweep to examine the effects of various factors on the neutral to earth voltage (NEV), including unsymmetrical system configuration, load unbalance and harmonic injection. The proposed algorithm composes fundamental frequency and harmonic frequencies power flows. The algorithm and the associated models are tested on IEEE 13 bus system. The magnitude of NEV is investigated under various conditions of the number of grounding rods per feeder lengths, the grounding rods resistance and the grounding resistance of the in feeding source. Additionally, the harmonic injection of nonlinear loads has been considered and its influences on NEV under different conditions are shown.
Abstract: The source voltage of high-power fuel cell shows strong load dependence at comparatively low voltage levels. In order to provide the voltage of 750V on the DC-link for feeding electrical energy into the mains via a three phase inverter a step-up converter with a large step-up ratio is required. The output voltage of this DC/DC-converter must be stabile during variations of the load current and the voltage of the fuel cell. This paper presents the methods and results of the calculation of the efficiency and the expense for the realization for the circuits of the DC/DC-converter that meet these requirements.
Abstract: Modern highly automated production systems faces
problems of reliability. Machine function reliability results in
changes of productivity rate and efficiency use of expensive
industrial facilities. Predicting of reliability has become an important
research and involves complex mathematical methods and
calculation. The reliability of high productivity technological
automatic machines that consists of complex mechanical, electrical
and electronic components is important. The failure of these units
results in major economic losses of production systems. The
reliability of transport and feeding systems for automatic
technological machines is also important, because failure of transport
leads to stops of technological machines. This paper presents
reliability engineering on the feeding system and its components for
transporting a complex shape parts to automatic machines. It also
discusses about the calculation of the reliability parameters of the
feeding unit by applying the probability theory. Equations produced
for calculating the limits of the geometrical sizes of feeders and the
probability of sticking the transported parts into the chute represents
the reliability of feeders as a function of its geometrical parameters.
Abstract: Fish-feed is a major cost component of operating expenses for any aquaculture farm. Due to soaring prices of fish-feed ingredients, the need for better feeding schedule management has become imperative. On such factor that influences the utilization rate of fish-feed are sea currents. Up to now, practical monitoring of fishfeed loss due to sea currents is not exercised. This paper gives a description of an economic methodology that aims at quantifying the amount of fish-feed lost due to sea currents and draws on data from a Mediterranean aquaculture farm to formulate the associated model.
Abstract: Fuel cells have become one of the major areas of
research in the academia and the industry. The goal of most fish
farmers is to maximize production and profits while holding labor
and management efforts to the minimum. Risk of fish kills, disease
outbreaks, poor water quality in most pond culture operations,
aeration offers the most immediate and practical solution to water
quality problems encountered at higher stocking and feeding rates.
Many units of aeration system are electrical units so using a
continuous, high reliability, affordable, and environmentally friendly
power sources is necessary. Aeration of water by using PEM fuel cell
power is not only a new application of the renewable energy, but
also, it provides an affordable method to promote biodiversity in
stagnant ponds and lakes. This paper presents a new design and
control of PEM fuel cell powered a diffused air aeration system for a
shrimp farm in Mersa Matruh in Egypt. Also Artificial intelligence
(AI) techniques control is used to control the fuel cell output power
by control input gases flow rate. Moreover the mathematical
modeling and simulation of PEM fuel cell is introduced. A
comparison study is applied between the performance of fuzzy logic
control (FLC) and neural network control (NNC). The results show
the effectiveness of NNC over FLC.
Abstract: In the present research, two nutraceuticals made from
red grape and walnut that showed previously to improve kidney
dysfunction were incorporated separately into functional foods' bread
made from barley and rice bran. The functional foods were evaluated
in rats in which chronic renal failure was induced through feeding
diet rich in adenine and phosphate (APD). The evaluation based on
assessing kidney function, oxidative stress, inflammatory biomarkers
and body weight gain. Results showed induction of chronic kidney
failure reflected in significant increase in plasma urea, creatinine,
malondialdehyde, tumor necrosis factor- α and low density
lipoprotein cholesterol along with significant reduction of plasma
albumin, and total antioxidant and creatinine clearance and body
weight gain on feeding APD compared to control healthy group.
Feeding the functional foods produced amelioration in the different
biochemical parameters and body weight gain indicating
improvement in kidney function.
Abstract: This paper presented a novel combined cycle of air separation and natural gas liquefaction. The idea is that natural gas can be liquefied, meanwhile gaseous or liquid nitrogen and oxygen are produced in one combined cryogenic system. Cycle simulation and exergy analysis were performed to evaluate the process and thereby reveal the influence of the crucial parameter, i.e., flow rate ratio through two stages expanders β on heat transfer temperature difference, its distribution and consequent exergy loss. Composite curves for the combined hot streams (feeding natural gas and recycled nitrogen) and the cold stream showed the degree of optimization available in this process if appropriate β was designed. The results indicated that increasing β reduces temperature difference and exergy loss in heat exchange process. However, the maximum limit value of β should be confined in terms of minimum temperature difference proposed in heat exchanger design standard and heat exchanger size. The optimal βopt under different operation conditions corresponding to the required minimum temperature differences was investigated.
Abstract: Dynamic models of power converters are normally
time-varying because of their switching actions. Several approaches
are applied to analyze the power converters to achieve the timeinvariant
models suitable for system analysis and design via the
classical control theory. The paper presents how to derive dynamic
models of the power system consisting of a three-phase controlled
rectifier feeding an uncontrolled buck converter by using the
combination between the well known techniques called the DQ and
the generalized state-space averaging methods. The intensive timedomain
simulations of the exact topology model are used to support
the accuracies of the reported model. The results show that the
proposed model can provide good accuracies in both transient and
steady-state responses.
Abstract: Recent medical studies have investigated the importance of enteral feeding and the use of feeding pumps for recovering patients unable to feed themselves or gain nourishment and nutrients by natural means. The most of enteral feeding system uses a peristaltic tube pump. A peristaltic pump is a form of positive displacement pump in which a flexible tube is progressively squeezed externally to allow the resulting enclosed pillow of fluid to progress along it. The squeezing of the tube requires a precise and robust controller of the geared motor to overcome parametric uncertainty of the pumping system which generates due to a wide variation of friction and slip between tube and roller. So, this paper proposes fuzzy adaptive controller for the robust control of the peristaltic tube pump. This new adaptive controller uses a fuzzy multi-layered architecture which has several independent fuzzy controllers in parallel, each with different robust stability area. Out of several independent fuzzy controllers, the most suited one is selected by a system identifier which observes variations in the controlled system parameter. This paper proposes a design procedure which can be carried out mathematically and systematically from the model of a controlled system. Finally, the good control performance, accurate dose rate and robust system stability, of the developed feeding pump is confirmed through experimental and clinic testing.
Abstract: Sixteen female Holstein calves allocated in three
treatments including: 1: control, 2: fed raw fiber concentrate (RFC)
for 45 days and 3: fed RFC for 90 days. RFC supplement (Vitacel®
200) was added to milk immediately before feeding (10 g/L milk).
Withers height and body weights of calves were measured monthly.
Individual dry matter intake was recorded daily. Blood samples were
taken monthly. The result showed that calves consumed RFC had
significantly greater weaning and final body weight. Treatment effect
on dry matter intake was not significant (p>0.05). Calves fed RFC
had better feed efficiency. Withers height of calves fed RFC were
taller than the control group (p
Abstract: Twenty four New Zealand white rabbits (12 does and
12 bucks) and twenty four Flanders (12 does and 12 bucks) rabbits,
allotted into two feeding regime (6 for each breed, 3 males and 3
females) first one fed commercial ration and second one fed
commercial diet plus sodium butyrate (300 g/ton). The obtained
results showed that at end of 8th week experimental period New
Zealand white rabbits were heavier body weight than Flanders rabbits
(1934.55+39.05 vs. 1802.5+30.99 g); significantly high body weight
gain during experimental period especially during 8th week
(136.1+3.5 vs. 126.8+1.8 g/week); better feed conversion ratio during
all weeks of experiment from first week (3.07+0.16 vs. 3.12+0.10)
till the 8th week of experiment (5.54+0.16 vs. 5.76+0.07) with
significantly high dressing percentages (0.54+0.01 vs. 0.52+0.01).
Also all carcass cuts were significantly high in New Zealand white
rabbits than Flanders. Females rabbits (at the same age) were lower
body weight than males from start of experiment (941.1+39.8
vs.972.1+33.5 g) till the end of experiment (1833.64+37.69 vs.
1903.41+36.93 g); gained less during all weeks of experiment except
during 8th week (132.1+2.3 vs. 130.9+3.4 g/week), with lower
dressing percentage (0.52+0.01 vs. 0.53+0.01) and lighter carcass
cuts than males, however, they had better feed conversion ratio
during 1st week, 7th week and 8th week of experiment. Addition of
300g sodium butyrate/ton of rabbit increased the body weight of
rabbits at the end of experimental period (1882.71+26.45 vs.
1851.5+49.82 g); improve body weight gain at 3rd, 4th, 5th, 6th and
7th week of experiment and significantly improve feed conversion
ratio during all weeks of the experiment from 1st week (2.85+0.07
vs. 3.30+0.15) till the 8th week of the experiment (5.51+0.12 vs.
5.77+0.12). Also the dressing percentage was higher in Sodium
butyrate fed groups than control one (0.53+0.01 vs. 0.52+0.01) and
the most important results of feeding sodium butyrate is the reducing
of the mortality percentage in rabbits during 8 week experiment to
zero percentage as compared with 16% in control group.
Abstract: The purpose of this study was to study postpartum breastfeeding mothers to determine the impact their psychosocial and spiritual dimensions play in promoting full-term (6 month duration) breastfeeding of their infants. Purposive and snowball sampling methods were used to identify and recruit the study's participants. A total of 23 postpartum mothers, who were breastfeeding within 6 weeks after giving birth, participated in this study. In-depth interviews combined with observations, participant focus groups, and ethnographic records were used for data collection. The Data were then analyzed using content analysis and typology. The results of this study illustrated that postpartum mothers experienced fear and worry that they would lack support from their spouse, family and peers, and that their infant would not get enough milk It was found that the main barrier mothers faced in breastfeeding to full-term was the difficulty of continuing to breastfeed when returning to work. 81.82% of the primiparous mothers and 91.67% of the non-primiparous mothers were able to breastfeed for the desired full-term of 6 months. Factors found to be related to breastfeeding for six months included 1) belief and faith in breastfeeding, 2) support from spouse and family members, 3) counseling from public health nurses and friends. The sample also provided evidence that religious principles such as tolerance, effort, love, and compassion to their infant, and positive thinking, were used in solving their physical, mental and spiritual problems.
Abstract: The dynamical contouring error is a critical element for the accuracy of machine tools. The contouring error is defined as the difference between the processing actual path and commanded path, which is implemented by following the command curves from feeding driving system in machine tools. The contouring error is resulted from various factors, such as the external loads, friction, inertia moment, feed rate, speed control, servo control, and etc. Thus, the study proposes a 2D compensating system for the contouring accuracy of machine tools. Optical method is adopted by using stable frequency laser diode and the high precision position sensor detector (PSD) to performno-contact measurement. Results show the related accuracy of position sensor detector (PSD) of 2D contouring accuracy compensating system was ±1.5 μm for a calculated range of ±3 mm, and improvement accuracy is over 80% at high-speed feed rate.
Abstract: This paper describes a method to measure and
compensate a 4 axes ultra-precision machine tool that generates micro
patterns on the large surfaces. The grooving machine is usually used
for making a micro mold for many electrical parts such as a light guide
plate for LCD and fuel cells. The ultra precision machine tool has three
linear axes and one rotational table. Shaping is usually used to
generate micro patterns. In the case of 50 μm pitch and 25 μm height
pyramid pattern machining with a 90° wedge angle bite, one of linear
axis is used for long stroke motion for high cutting speed and other
linear axis are used for feeding. The triangular patterns can be
generated with many times of long stroke of one axis. Then 90°
rotation of work piece is needed to make pyramid patterns with
superposition of machined two triangular patterns.
To make a two dimensional positioning error, straightness of two
axes in out of plane, squareness between the each axis are important.
Positioning errors, straightness and squarness were measured by laser
interferometer system. Those were compensated and confirmed by
ISO230-6. One of difficult problem to measure the error motions is
squareness or parallelism of axis between the rotational table and
linear axis. It was investigated by simultaneous moving of rotary table
and XY axes. This compensation method is introduced in this paper.
Abstract: The fluorescent pseudomonad strain R81 is a root
colonizing rhizobacteria which promotes the growth of many plants
by various mechanisms. Its broth containing siderophore (ironchelating
compound) and 2,4- diacetyl phloroglucinol (DAPG) is
used for preparing bioinoculant formulations for agronomical
applications. Glycerol was found to be the best carbon source for
improved biomass production. Splitting of nitrogen source to NH4Cl
and urea had a stabilizing effect on pH during batch cultivation. Ltryptophan
at 0.5 % in the medium increased the siderophore
production to 850 mg/l. During batch cultivation of the strain in a
bioreactor, a maximum of 4 g/l of dry cell mass, 1.8 g/l of
siderophore and 20 mg/l of DAPG was achieved when glycerol was
15 g/l and C/N ratio was maintained at 12.5. In case of intermittent
feeding of fresh medium during fed-batch cultivation, the dry cell
mass was increased to 25 g/l with improved production of DAPG to
70 mg/l.
Abstract: This paper describes a steady state model of a multiple
effect evaporator system for simulation and control purposes. The
model includes overall as well as component mass balance equations,
energy balance equations and heat transfer rate equations for area
calculations for all the effects. Each effect in the process is
represented by a number of variables which are related by the energy
and material balance equations for the feed, product and vapor flow
for backward, mixed and split feed. For simulation 'fsolve' solver in
MATLAB source code is used. The optimality of three sequences i.e.
backward, mixed and splitting feed is studied by varying the various
input parameters.
Abstract: Exclusive breastfeeding is the feeding of a baby on no other milk apart from breast milk. Exclusive breastfeeding during the first 6 months of life is very important as it supports optimal growth and development during infancy and reduces the risk of obliterating diseases and problems. Moreover, it helps to reduce the incidence and/or severity of diarrhea, lower respiratory infection and urinary tract infection. In this paper, we make a survey of the factors that influence exclusive breastfeeding and use two dispersed statistical models to analyze data. The models are the Generalized Poisson regression model and the Com-Poisson regression models.
Abstract: In this study Vitaton (an organic supplement which
contains fermentative β-carotene) and synthetic astaxanthin
(CAROPHYLL® Pink) were evaluated as pro-growth factors in
Rainbow trout diet. An 8 week feeding trial was conducted to
determine the effects of Vitaton versus astaxanthin on rearing factors,
survival rate and visual flesh color of Rainbow trout
(Oncorhnchynchus mykiss) with initial weight of 196±5. Four
practical diets were formulated to contain 50 and 80 (ppm) of β-
carotene and astaxanthin and also a control diet was prepared without
any pigment. Each diet was fed to triplicate groups of fish rearing in
fresh water. Fish were fed twice daily. The water temperature
fluctuated from 12 to 15 (C˚) and also dissolved oxygen content was
between 7 to 7.5 (mg/lit) during the experimental period. At the end
of the experiment, growth and food utilization parameters and
survival rate were unaffected by dietary treatments (p>0.05). Also,
there was no significant difference between carcass yield within
treatments (p>0.05). No significant difference recognized between
visual flesh color (SalmoFan score) of fish fed Vitaton-containing
diets. On the contrary, feeding on diets containing 50 and 80 (ppm)
of astaxanthin, increased SalmoFan score (flesh astaxanthin
concentration) from
Abstract: Breastfeeding has been receiving much attention of late. Prolonged sitting for breastfeeding often results in back pain of the mothers. This paper reports the findings of a study on the effect of some factors, especially lumbar support, on back pain of breastfeeding mothers. The results showed that the use of lumbar support can reduce back pain of breastfeeding mothers significantly. Back pain was found to increase with breastfeeding time and the rate of increase was lower when lumbar supports were used. When lumbar support thickness was increased gradually from zero (no support) to 11 cm., the degree of low back pain decreased; rapidly at first, then slowly, and leveled off when the thickness reached 9 cm. Younger mothers were less prone to back pain than older mothers. The implications of the findings are discussed.