Abstract: In this paper, the energy saving and human thermal
comfort in a typical office room are investigated. The impact of a
combined system of exhaust inlet air with light slots located at the
ceiling level in a room served by displacement ventilation system is
numerically modelled. Previous experimental data are used to
validate the Computational Fluid Dynamic (CFD) model. A case
study of simulated office room includes two seating occupants, two
computers, two data loggers and four lamps. The combined system is
located at the ceiling level above the heat sources. A new method of
calculation for the cooling coil load in Stratified Air Distribution
(STRAD) system is used in this study. The results show that 47.4%
energy saving of space cooling load can be achieved by combing the
exhaust inlet air with light slots at the ceiling level above the heat
sources.
Abstract: Steady three-dimensional and two free surface waves
generated by moving bodies are presented, the flow problem to be
simulated is rich in complexity and poses many modeling challenges
because of the existence of breaking waves around the ship hull, and
because of the interaction of the two-phase flow with the turbulent
boundary layer. The results of several simulations are reported. The
first study was performed for NACA0012 of hydrofoil with different
meshes, this section is analyzed at h/c= 1, 0345 for 2D. In the second
simulation a mathematically defined Wigley hull form is used to
investigate the application of a commercial CFD code in prediction of
the total resistance and its components from tangential and normal
forces on the hull wetted surface. The computed resistance and wave
profiles are used to estimate the coefficient of the total resistance for
Wigley hull advancing in calm water under steady conditions. The
commercial CFD software FLUENT version 12 is used for the
computations in the present study. The calculated grid is established
using the code computer GAMBIT 2.3.26. The shear stress k-ωSST
model is used for turbulence modeling and the volume of fluid
technique is employed to simulate the free-surface motion. The
second order upwind scheme is used for discretizing the convection
terms in the momentum transport equations, the Modified HRIC
scheme for VOF discretization. The results obtained compare well
with the experimental data.
Abstract: Steady three-dimensional and two free surface waves
generated by moving bodies are presented, the flow problem to be
simulated is rich in complexity and poses many modeling challenges
because of the existence of breaking waves around the ship hull, and
because of the interaction of the two-phase flow with the turbulent
boundary layer. The results of several simulations are reported. The
first study was performed for NACA0012 of hydrofoil with different
meshes, this section is analyzed at h/c= 1, 0345 for 2D. In the second
simulation a mathematically defined Wigley hull form is used to
investigate the application of a commercial CFD code in prediction of
the total resistance and its components from tangential and normal
forces on the hull wetted surface. The computed resistance and wave
profiles are used to estimate the coefficient of the total resistance for
Wigley hull advancing in calm water under steady conditions. The
commercial CFD software FLUENT version 12 is used for the
computations in the present study. The calculated grid is established
using the code computer GAMBIT 2.3.26. The shear stress k-ωSST
model is used for turbulence modeling and the volume of fluid
technique is employed to simulate the free-surface motion. The
second order upwind scheme is used for discretizing the convection
terms in the momentum transport equations, the Modified HRIC
scheme for VOF discretization. The results obtained compare well
with the experimental data.
Abstract: Nowadays, the main goal for modern horticultural
production is an increase the quality. In recent years, the use of
organic fertilizers or biostimulants that can be applied in agriculture
to improve quali-quantitative crop yields has encountered increasing
interest. Biostimulants are gaining importance also for their possible
use in organic and sustainable agriculture, to avoid excessive
fertilizer applications. Consecutive experimental trials were carried
out in the Apulia region (southern Italy) on three herbaceous crops
(cauliflower, pepper, fennel) grown in pots under conventional and
organic fertilization systems without and with biostimulants. The aim
was to determine the effects of three biostimulants (Siapton®10L,
Micotech L, Lysodin Alga-Fert) on quali-quantitative yield
characteristics. At harvest, the quali-quantitative yield characteristics
of each crop were determined. All of the experimental data were
subjected to analysis of variance (ANOVA), and when significant
effects were detected, the means were compared using Tukey’s tests.
These data show large differences in these yield characteristics
between conventional and organic crops, particularly highlighting
higher yields for the conventional crops, while variable results were
generally observed when the biostimulants were applied. In this
context, there were no effects of the biostimulants on the quantitative
yield, whereas there were low positive effects on the qualitative
characteristics, as related to higher dry matter content of cauliflower,
and higher soluble solids content of pepper. Moreover, there were
evident positive effects of the biostimulants with fennel, due to the
lower nitrate content. These latter data are in line with most of the
published literature obtained for other herbaceous crops.
Abstract: Pneumatic reactors have been widely employed in various sectors of the chemical industry, especially where are required high heat and mass transfer rates. This study aimed to obtain correlations that allow the prediction of gas hold-up (Ԑ) and volumetric oxygen transfer coefficient (kLa), and compare these values, for three models of pneumatic reactors on two scales utilizing Newtonian fluids. Values of kLa were obtained using the dynamic pressure-step method, while e was used for a new proposed measure. Comparing the three models of reactors studied, it was observed that the mass transfer was superior to draft-tube airlift, reaching e of 0.173 and kLa of 0.00904s-1. All correlations showed good fit to the experimental data (R2≥94%), and comparisons with correlations from the literature demonstrate the need for further similar studies due to shortage of data available, mainly for airlift reactors and high viscosity fluids.
Abstract: The fatigue life of tubular joints commonly found in
offshore industry is not only dependent on the value of hot-spot stress
(HSS), but is also significantly influenced by the through-thethickness
stress distribution characterized by the degree of bending
(DoB). The determination of DoB values in a tubular joint is essential
for improving the accuracy of fatigue life estimation using the stresslife
(S–N) method and particularly for predicting the fatigue crack
growth based on the fracture mechanics (FM) approach. In the
present paper, data extracted from finite element (FE) analyses of
tubular KT-joints, verified against experimental data and parametric
equations, was used to investigate the effects of geometrical
parameters on DoB values at the crown 0°, saddle, and crown 180°
positions along the weld toe of central brace in tubular KT-joints
subjected to axial loading. Parametric study was followed by a set of
nonlinear regression analyses to derive DoB parametric formulas for
the fatigue analysis of KT-joints under axial loads. The tubular KTjoint
is a quite common joint type found in steel offshore structures.
However, despite the crucial role of the DoB in evaluating the fatigue
performance of tubular joints, this paper is the first attempt to study
and formulate the DoB values in KT-joints.
Abstract: The polymer foil used for manufacturing of
laminated glass members behaves in a viscoelastic manner with
temperature dependance. This contribution aims at incorporating
the time/temperature-dependent behavior of interlayer to our earlier
elastic finite element model for laminated glass beams. The model
is based on a refined beam theory: each layer behaves according
to the finite-strain shear deformable formulation by Reissner and
the adjacent layers are connected via the Lagrange multipliers
ensuring the inter-layer compatibility of a laminated unit. The
time/temperature-dependent behavior of the interlayer is accounted
for by the generalized Maxwell model and by the time-temperature
superposition principle due to the Williams, Landel, and Ferry.
The resulting system is solved by the Newton method with
consistent linearization and the viscoelastic response is determined
incrementally by the exponential algorithm. By comparing the model
predictions against available experimental data, we demonstrate that
the proposed formulation is reliable and accurately reproduces the
behavior of the laminated glass units.
Abstract: The model tests were conducted in the laboratory
without and with Plastic recycled polymer in fly ash steep slopes
overlaying soft foundation soils like fly ash and powai soil in order to
check the stability of steep slope. In this experiment, fly ash is used
as a filling material and Plastic Recycled Polymers of diameter =
3mm and length = 4mm were made from waste plastic product (lower
grade plastic product). The properties of fly ash and Plastic recycled
polymers are determined. From the experiments, load and settlement
have measured. From these data, load –settlement curves have
reported. It has been observed from test results that load carrying
capacity of mixture fly ash with Plastic Recycled Polymers slope is
more than that of fly ash slope. The deformation of Plastic Recycled
Polymers slope is slightly more than that of fly ash slope. A Finite
Element Method (F.E.M.) was also evaluated using PLAXIS 3D
version. The failure pattern, deformations and factor of safety are
reported based on analytical programme. The results from
experimental data and analytical programme are compared and
reported.
Abstract: This paper is focused on the CFD simulation of the radiaxial pump (i.e. mixed flow pump) with the aim to detect the reasons of Y-Q characteristic instability. The main reasons of pressure pulsations were detected by means of the analysis of velocity and pressure fields within the pump combined with the theoretical approach. Consequently, the modifications of spiral case and pump suction area were made based on the knowledge of flow conditions and the shape of dissipation function. The primary design of pump geometry was created as the base model serving for the comparison of individual modification influences. The basic experimental data are available for this geometry. This approach replaced the more complicated and with respect to convergence of all computational tasks more difficult calculation for the compressible liquid flow. The modification of primary pump consisted in inserting the three fins types. Subsequently, the evaluation of pressure pulsations, specific energy curves and visualization of velocity fields were chosen as the criterion for successful design.
Abstract: In this paper, a numerical simulation of a finned store
separating from a wing-pylon configuration has been studied and
validated. A dynamic unstructured tetrahedral mesh approach is
accomplished by using three grid sizes to numerically solving the
discretized three dimensional, inviscid and compressible Euler
equations. The method used for computations of separation of an
external store assuming quasi-steady flow condition. Computations of
quasi-steady flow have been directly coupled to a six degree-offreedom
(6DOF) rigid-body motion code to generate store
trajectories. The pressure coefficients at four different angular cuts
and time histories of various trajectory parameters and wing pressure
distribution during the store separation are compared for every grid
size with published experimental data.
Abstract: The hydrodynamics and heat transfer characteristics
of a vaporized elongated bubble in a rectangular microchannel have
been simulated based on Cahn-Hilliard phase-field method. In the
simulations, the initially nucleated bubble starts growing as it comes
in contact with superheated water. The growing shape of the bubble
compared well with the available experimental data in the literature.
Abstract: Incineration of municipal solid waste (MSW) is one of
the key scopes in the global clean energy strategy. A computational
fluid dynamics (CFD) model was established in order to reveal these
features of the combustion process in a fixed porous bed of MSW.
Transporting equations and process rate equations of the waste bed
were modeled and set up to describe the incineration process,
according to the local thermal conditions and waste property
characters. Gas phase turbulence was modeled using k-ε turbulent
model and the particle phase was modeled using the kinetic theory of
granular flow. The heterogeneous reaction rates were determined
using Arrhenius eddy dissipation and the Arrhenius-diffusion
reaction rates. The effects of primary air flow rate and temperature in
the burning process of simulated MSW are investigated
experimentally and numerically. The simulation results in bed are
accordant with experimental data well. The model provides detailed
information on burning processes in the fixed bed, which is otherwise
very difficult to obtain by conventional experimental techniques.
Abstract: A three-dimensional numerical model of
thermoelectric generator (TEG) modules attached to a large chimney
plate is proposed and solved numerically using a control volume based
finite difference formulation. The TEG module consists of a
thermoelectric generator, an elliptical pin-fin heat sink, and a cold
plate for water cooling. In the chimney, the temperature of flue gases is
450-650K. Although the TEG hot-side temperature and thus the
electric power output can be increased by inserting an elliptical pin-fin
heat sink into the chimney tunnel to increase the heat transfer area, the
pin fin heat sink would cause extra pumping power at the same time.
The main purpose of this study is to analyze the effects of geometrical
parameters on the electric power output and chimney pressure drop
characteristics. The effects of different operating conditions, including
various inlet velocities (Vin= 1, 3, 5 m/s), inlet temperatures (Tgas = 450,
550, 650K) and different fin height (0 to 150 mm) are discussed in
detail. The predicted numerical data for the power vs. current (P-I)
curve are in good agreement (within 11%) with the experimental data.
Abstract: The key role in phenomenological modelling of cyclic
plasticity is good understanding of stress-strain behaviour of given
material. There are many models describing behaviour of materials
using numerous parameters and constants. Combination of individual
parameters in those material models significantly determines whether
observed and predicted results are in compliance. Parameter
identification techniques such as random gradient, genetic algorithm
and sensitivity analysis are used for identification of parameters using
numerical modelling and simulation. In this paper genetic algorithm
and sensitivity analysis are used to study effect of 4 parameters of
modified AbdelKarim-Ohno cyclic plasticity model. Results
predicted by Finite Element (FE) simulation are compared with
experimental data from biaxial ratcheting test with semi-elliptical
loading path.
Abstract: This work deals with parameter identification of
permanent magnet motors, a class of ac motor which is particularly
important in industrial automation due to characteristics like
applications high performance, are very attractive for applications
with limited space and reducing the need to eliminate because they
have reduced size and volume and can operate in a wide speed range,
without independent ventilation. By using experimental data and
genetic algorithm we have been able to extract values for both the
motor inductance and the electromechanical coupling constant, which
are then compared to measured and/or expected values.
Abstract: China is currently the world's largest producer and distributor of electric bicycle (e-bike). The increasing number of e-bikes on the road is accompanied by rising injuries and even deaths of e-bike drivers. Therefore, there is a growing need to improve the safety structure of e-bikes. This 3D frictionless contact analysis is a preliminary, but necessary work for further structural design improvement of an e-bike. The contact analysis between e-bike and the ground was carried out as follows: firstly, the Penalty method was illustrated and derived from the simplest spring-mass system. This is one of the most common methods to satisfy the frictionless contact case; secondly, ANSYS static analysis was carried out to verify finite element (FE) models with contact pair (without friction) between e-bike and the ground; finally, ANSYS transient analysis was used to obtain the data of the penetration p(u) of e-bike with respect to the ground. Results obtained from the simulation are as estimated by comparing with that from theoretical method. In the future, protective shell will be designed following the stability criteria and added to the frame of e-bike. Simulation of side falling of the improvedsafety structure of e-bike will be confirmed with experimental data.
Abstract: The Cone Penetration Test (CPT) is a common in-situ
test which generally investigates a much greater volume of soil more
quickly than possible from sampling and laboratory tests. Therefore,
it has the potential to realize both cost savings and assessment of soil
properties rapidly and continuously. The principle objective of this
paper is to demonstrate the feasibility and efficiency of using
artificial neural networks (ANNs) to predict the soil angle of internal
friction (Φ) and the soil modulus of elasticity (E) from CPT results
considering the uncertainties and non-linearities of the soil. In
addition, ANNs are used to study the influence of different
parameters and recommend which parameters should be included as
input parameters to improve the prediction. Neural networks discover
relationships in the input data sets through the iterative presentation
of the data and intrinsic mapping characteristics of neural topologies.
General Regression Neural Network (GRNN) is one of the powerful
neural network architectures which is utilized in this study. A large
amount of field and experimental data including CPT results, plate
load tests, direct shear box, grain size distribution and calculated data
of overburden pressure was obtained from a large project in the
United Arab Emirates. This data was used for the training and the
validation of the neural network. A comparison was made between
the obtained results from the ANN's approach, and some common
traditional correlations that predict Φ and E from CPT results with
respect to the actual results of the collected data. The results show
that the ANN is a very powerful tool. Very good agreement was
obtained between estimated results from ANN and actual measured
results with comparison to other correlations available in the
literature. The study recommends some easily available parameters
that should be included in the estimation of the soil properties to
improve the prediction models. It is shown that the use of friction
ration in the estimation of Φ and the use of fines content in the
estimation of E considerable improve the prediction models.
Abstract: Experimental & numeral study of temperature
distribution during milling process, is important in milling quality
and tools life aspects. In the present study the milling cross-section
temperature is determined by using Artificial Neural Networks
(ANN) according to the temperature of certain points of the work
piece and the point specifications and the milling rotational speed of
the blade. In the present work, at first three-dimensional model of the
work piece is provided and then by using the Computational Heat
Transfer (CHT) simulations, temperature in different nods of the
work piece are specified in steady-state conditions. Results obtained
from CHT are used for training and testing the ANN approach. Using
reverse engineering and setting the desired x, y, z and the milling
rotational speed of the blade as input data to the network, the milling
surface temperature determined by neural network is presented as
output data. The desired points temperature for different milling
blade rotational speed are obtained experimentally and by
extrapolation method for the milling surface temperature is obtained
and a comparison is performed among the soft programming ANN,
CHT results and experimental data and it is observed that ANN soft
programming code can be used more efficiently to determine the
temperature in a milling process.
Abstract: Based on the experimental data, the impact of
resistance and reactance of the winding, as well as the magnetic
permeability of the magnetic circuit steel material on the value of the
electromotive force of the induction converter is investigated. The
obtained results allow estimating the main technological spreads and
determining the maximum level of the electromotive force change.
By the method of experiment planning, the expression of a
polynomial for the electromotive force which can be used to estimate
the adequacy of mathematical models to be used at the investigation
and design of induction converters is obtained.
Abstract: Artificial intelligence applications are commonly used
in industry in many fields in parallel with the developments in the
computer technology. In this study, a fire room was prepared for the
resistance of wooden construction elements and with the mechanism
here, the experiments of polished materials were carried out. By
utilizing from the experimental data, an artificial neural network
(ANN) was modelled in order to evaluate the final cross sections of
the wooden samples remaining from the fire. In modelling,
experimental data obtained from the fire room were used. In the
developed system, the first weight of samples (ws-gr), preliminary
cross-section (pcs-mm2), fire time (ft-minute), and fire temperature
(t-oC) as input parameters and final cross-section (fcs-mm2) as output
parameter were taken. When the results obtained from ANN and
experimental data are compared after making statistical analyses, the
data of two groups are determined to be coherent and seen to have no
meaning difference between them. As a result, it is seen that ANN
can be safely used in determining cross sections of wooden materials
after fire and it prevents many disadvantages.