Abstract: This study was to investigate the performance of
hybrid solvents blended between primary, secondary, or tertiary
amines and piperazine (PZ) for CO2 removal from flue gas in terms
of CO2 absorption capacity and regeneration efficiency at 90 oC.
Alkanolamines used in this work were monoethanolamine (MEA),
diethanolamine (DEA), and triethanolamine (TEA). The CO2
absorption was experimentally examined under atmospheric pressure
and room temperature. The results show that MEA blend with PZ
provided the maximum CO2 absorption capacity of 0.50 mol
CO2/mol amine while TEA provided the minimum CO2 absorption
capacity of 0.30 mol CO2/mol amine. TEA was easier to regenerate
for both first cycle and second cycle with less loss of absorption
capacity. The regeneration efficiency of TEA was 95.09 and 92.89 %,
for the first and second generation cycles, respectively.
Abstract: White rust, caused by Albugo candida, is the most
destructive foliar diseases of persian cress, Lepidium sativum in Iran.
Application of fungicide is the most common method for the disease
control. However, regarding the problems created by synthetic
pesticides application, environmentally safe methods are needed to
replace chemical pesticides. In this study, the antifungal activity of
plant natural extracts was investigated for their ability to inhibit
zoospore release from sporangia of A. candida. The crude extract of
46 plants was obtained using methanol. The inhibitory effect of the
extracts was examined by mixing the plant extracts with a
zoosporangial suspension of A. candida (1×106 spore/ml) at three
concentrations, 250, 100 and 50 ppm. The experiments were
conducted in a completely randomized design, with three replicates.
The results of the experiment showed that three out of 46 plants
species, including, Rhus coriaria, Anagallis arvensis and Mespilus
germanica were completely inhibit zoospore release from
zoosporangia of Albugo candida at concentration of 50 ppm.
Abstract: Biodiesel production with used frying by
transesterification reaction with methanol, using a commercial
kaolinite thermally-activated solid acid catalyst was investigated.
The surface area, the average pore diameter and pore volume of the
kaolinite catalyst were 10 m2/g, 13.0 nm and 30 mm3/g, respectively.
The optimal conditions for the transesterification reaction were
determined to be oil/methanol, in a molar ratio 1:31, temperature 160
ºC and catalyst concentration of 3% (w/w). The yield of fatty acids
methyl esters (FAME) was 92.4% after 2 h of reaction. This method
of preparation of biodiesel can be a positive alternative for utilizing
used frying corn oil for feedstock of biodiesel combined with the
inexpensive catalyst.
Abstract: The nature of adsorbed species on catalytic surface
over an industrial precipitated iron-based high temperature catalyst
during FTS was investigated by in-situ DRIFTS and chemical
trapping. The formulation of the mechanism of oxygenates formation
and key intermediates were also discussed. Numerous oxygenated
precursors and crucial intermediates were found by in-situ DRIFTS,
such as surface acetate, acetyl and methoxide. The results showed that
adsorbed molecules on surface such as methanol or acetaldehyde
could react with basic sites such as lattice oxygen or free surface
hydroxyls. Adsorbed molecules also had reactivity of oxidizing.
Moreover, acetyl as a key intermediate for oxygenates was observed
by investigation of CH3OH + CO and CH3I + CO + H2. Based on the
nature of surface properties, the mechanism of oxygenates formation
on precipitated iron-based high temperature catalyst was discussed.
Abstract: The paper relates to a catalyst, comprising copperchromium
spinel, coated on carrier γ-Al2O3. The effect of preparation
conditions on the active component composition and activity
behavior of the catalysts is discussed. It was found that the activity of
carbon monoxide, DME, formaldehyde and methanol oxidation
reaches a maximum at an active component content of 20 – 30 wt. %.
Temperature calcination at 500oC seems to be optimal for the γ–
alumina supported CuO-Cr2O3 catalysts for CO, DME, formaldehyde
and methanol oxidation. A three months industrial experiment was
carried out to elucidate the changes in the catalyst composition
during industrial exploitation of the catalyst and the main reasons for
catalyst deactivation.
It was concluded that the CuO–Cr2O3/γ–alumina supported
catalysts have enhanced activity toward CO, DME, formaldehyde
and methanol oxidation and that these catalysts are suitable for
industrial application. The main reason for catalyst deactivation
seems to be the deposition of iron and molybdenum, coming from the
main reactor, on the active component surface.
Abstract: This study has investigated the antidiabetic and
antioxidant potential of Pseudovaria macrophylla bark extract on
streptozotocin–nicotinamide induced type 2 diabetic rats. LCMSQTOF
and NMR experiments were done to determine the chemical
composition in the methanolic bark extract. For in vivo experiments,
the STZ (60 mg/kg/b.w, 15 min after 120 mg/kg/1 nicotinamide, i.p.)
induced diabetic rats were treated with methanolic extract of
Pseuduvaria macrophylla (200 and 400 mg/kg·bw) and
glibenclamide (2.5 mg/kg) as positive control respectively.
Biochemical parameters were assayed in the blood samples of all
groups of rats. The pro-inflammatory cytokines, antioxidant status
and plasma transforming growth factor βeta-1 (TGF-β1) were
evaluated. The histological study of the pancreas was examined and
its expression level of insulin was observed by
immunohistochemistry. In addition, the expression of glucose
transporters (GLUT 1, 2 and 4) were assessed in pancreas tissue by
western blot analysis. The outcomes of the study displayed that the
bark methanol extract of Pseuduvaria macrophylla has potentially
normalized the elevated blood glucose levels and improved serum
insulin and C-peptide levels with significant increase in the
antioxidant enzyme, reduced glutathione (GSH) and decrease in the
level of lipid peroxidation (LPO). Additionally, the extract has
markedly decreased the levels of serum pro-inflammatory cytokines
and transforming growth factor beta-1 (TGF-β1). Histopathology
analysis demonstrated that Pseuduvaria macrophylla has the
potential to protect the pancreas of diabetic rats against peroxidation
damage by downregulating oxidative stress and elevated
hyperglycaemia. Furthermore, the expression of insulin protein,
GLUT-1, GLUT-2 and GLUT-4 in pancreatic cells was enhanced.
The findings of this study support the anti-diabetic claims of
Pseudovaria macrophylla bark.
Abstract: This work aims to investigate a potential of
microalgae for utilizing industrial wastewater as a cheap nutrient for
their growth and oil accumulation. Wastewater was collected from
the effluent ponds of agro-industrial factories (cassava and ethanol
production plants). Only 2 microalgal strains were isolated and
identified as Scenedesmus quadricauda and Chlorella sp.. However,
only S. quadricauda was selected to cultivate in various wastewater
concentrations (10%, 20%, 40%, 60%, 80% and 100%). The highest
biomass obtained at 6.6×106 and 6.27×106 cells/ml when 60%
wastewater was used in flask and photo-bioreactor. The cultures gave
the highest lipid content at 18.58 % and 42.86% in cases of S.
quadricauda and S. obliquus. In addition, under salt stress (1.0 M
NaCl), S. obliquus demonstrated the highest lipid content at 50%
which was much more than the case of no NaCl adding. However, the
concentration of NaCl does not affect on lipid accumulation in case
of S. quadricauda.
Abstract: Adsorption of methanol and ethanol over mesoporous
siliceous material are studied in the current paper. The pure
mesoporous silica is prepared using tetraethylorthosilicate (TEOS) as
silica source and dodecylamine as template at low pH. The prepared
material was characterized using nitrogen adsorption,nX-ray
diffraction (XRD) and scanning electron microscopy (SEM). The
adsorption kinetics of methanol and ethanol from aqueous solution
were studied over the prepared mesoporous silica material. The
percent removal of alcohol was calculated per unit mass of adsorbent
used. The 1st order model is found to be in agreement with both
adsorbates while the 2nd order model fit the adsorption of methanol
only.
Abstract: Antibacterial activity of Plumeria alba (Frangipani)
petals methanolic extracts were evaluated against Escherichia coli,
Proteus vulgaris,Staphylococcus aureus, Klebsiella pneumoniae,
Pseudomonas aeruginosa, Staphylococcus saprophyticus,
Enterococcus faecalis and Serratia marcescens by using disk
diffusion method. Concentration extracts (80 %) showed the highest
inhibition zone towards Escherichia coli (14.3 mm). Frangipani
extract also showed high antibacterial activity against
Staphylococcus saprophyticus, Proteus vulgaris and Serratia
marcescens, but not more than the zones of the positive control used.
Comparison between two broad specrum antibiotics to frangipani
extracts showed that the 80 % concentration extracts produce the
same zone of inhibition as Streptomycin. Frangipani extracts showed
no bacterial activity towards Klebsiella pneumoniae, Pseudomonas
aeruginosa and Enterococcus faecalis. There are differences in the
sensitivity of different bacteria to frangipani extracts, suggesting that
frangipani-s potency varies between these bacteria. The present
results indicate that frangipani showed significant antibacterial
activity especially to Escherichia coli.
Abstract: A high performance thin layer chromatography
system (HPTLC) for the separation of vitamin B2 and B12 has been
developed. The separation was successfully using a solvent system of
methanol, water, ammonia 7.3.1 (V/V) as mobile phase on HPTLC
plates impregnated with boric acid. The effect of other mobile phases
on the separation of vitamins was also examined. The method is
based on different behavior of investigated compounds in
impregnated TLC plates with different amount of boric acid. The Rf
values of vitamin B2 and B12 are considered on non impregnated
and impregnated silica gel HPTLC plate with boric acid. The effect
of boric acid in the mobile phase and on HPTLC plates on the RF
values of the vitamins has also been studied.
Abstract: In this paper, Zinc Oxide (ZnO) thin films are deposited on glass substrate by sol-gel method. The ZnO thin films with well defined orientation were acquired by spin coating of zinc acetate dehydrate monoethanolamine (MEA), de-ionized water and isopropanol alcohol. These films were pre-heated at 275°C for 10 min and then annealed at 350°C, 450°C and 550°C for 80 min. The effect of annealing temperature and different thickness on structure and surface morphology of the thin films were verified by Atomic Force Microscopy (AFM). It was found that there was a significant effect of annealing temperature on the structural parameters of the films such as roughness exponent, fractal dimension and interface width. Thin films also were characterizied by X-ray Diffractometery (XRD) method. XRD analysis revealed that the annealed ZnO thin films consist of single phase ZnO with wurtzite structure and show the c-axis grain orientation. Increasing annealing temperature increased the crystallite size and the c-axis orientation of the film after 450°C. Also In this study, ZnO thin films in different thickness have been prepared by sol-gel method on the glass substrate at room temperature. The thicknesses of films are 100, 150 and 250 nm. Using fractal analysis, morphological characteristics of surface films thickness in amorphous state were investigated. The results show that with increasing thickness, surface roughness (RMS) and lateral correlation length (ξ) are decreased. Also, the roughness exponent (α) and growth exponent (β) were determined to be 0.74±0.02 and 0.11±0.02, respectively.
Abstract: There was a high rate of corrosion in Pyrolysis
Gasoline Hydrogenation (PGH) unit of Arak Petrochemical Company
(ARPC), and it caused some operational problem in this plant. A
commercial chemical had been used as anti-corrosion in the
depentanizer column overhead in order to control the corrosion rate.
Injection of commercial corrosion inhibitor caused some
operational problems such as fouling in some heat exchangers. It was
proposed to replace this commercial material with another more
effective trouble free, and well-known additive by R&D and
operation specialists.
At first, the system was simulated by commercial simulation
software in electrolytic system to specify low pH points inside the
plant. After a very comprehensive study of the situation and technical
investigations ,ammonia / monoethanol amine solution was proposed
as neutralizer or corrosion inhibitor to be injected in a suitable point
of the plant. For this purpose, the depentanizer column and its
accessories system was simulated again in case of this solution
injection.
According to the simulation results, injection of new anticorrosion
substance has no any side effect on C5 cut product and
operating conditions of the column. The corrosion rate will be
cotrolled, if the pH remains at the range of 6.5 to 8 . Aactual plant
test run was also carried out by injection of ammonia / monoethanol
amine solution at the rate of 0.6 Kg/hr and the results of iron content
of water samples and corrosion test coupons confirmed the
simulation results.
Now, ammonia / monoethanol amine solution is injected to a
suitable pint inside the plant and corrosion rate has decreased
significantly.
Abstract: Gas hydrates form when a number of factors co-exist:
free water, hydrocarbon gas, cold temperatures and high pressures are typical of the near mud-line conditions in a deepwater drilling
operation. Subsequently, when drilling with water based muds, particularly on exploration wells, the risk of hydrate formation
associated with a gas influx is high. The consequences of gas hydrate
formation while drilling are severe, and as such, every effort should be made to ensure the risk of hydrate formation is either eliminated
or significantly reduced. Thermodynamic inhibitors are used to reduce the free water content of a drilling mud, and thus suppress the
hydrate formation temperature. Very little experimental work has
been performed by oil and gas research companies on the evaluation
of gas hydrate formation in a water-based drilling mud. The main
objective of this paper is to investigate the experimental gas hydrate
formation for a mixture of methane, carbon dioxide & nitrogen in a
water-based drilling mud with or without presence of different
concentrations of thermodynamic inhibitors including pure salt and a
combination of salt with methanol or ethylene glycol at different
concentrations in a static loop apparatus. The experiments were
performed using a static loop apparatus consisting of a 2.4307 cm
inside diameter and 800 cm long pipe. All experiments were conducted at 2200 psia. The temperature in the loop was decreased at
a rate of 3.33 °F/h from initial temperature of 80 °F.
Abstract: The conventional production of biodiesel from crude
palm oil which contains large amounts of free fatty acids in the
presence of a homogeneous base catalyst confronts the problems of
soap formation and very low yield of biodiesel. To overcome these
problems, free fatty acids must be esterified to their esters in the
presence of an acid catalyst prior to alkaline-catalyzed
transesterification. Sulfated metal oxides are a promising group of
catalysts due to their very high acidity. In this research, aluminadoped
sulfated tin oxide (SO4
2-/Al2O3-SnO2) catalysts were prepared
and used for esterification of free fatty acids in crude palm oil in a
batch reactor. The SO4
2-/Al2O3-SnO2 catalysts were prepared from
different Al precursors. The results showed that different Al
precursors gave different activities of the SO4
2-/Al2O3-SnO2 catalysts.
The esterification of free fatty acids in crude palm oil with methanol
in the presence of SO4
2-/Al2O3-SnO2 catalysts followed first-order
kinetics.
Abstract: The complex structure of lignocellulose leads to great
difficulties in converting it to fermentable sugars for the ethanol
production. The major hydrolysis impediments are the crystallinity of
cellulose and the lignin content. To improve the efficiency of
enzymatic hydrolysis, microbial pretreatment of corncob was
investigated using two bacterial strains of Bacillus subtilis A 002 and
Cellulomonas sp. TISTR 784 (expected to break open the crystalline
part of cellulose) and lignin-degrading fungus, Phanerochaete
sordida SK7 (expected to remove lignin from lignocellulose). The
microbial pretreatment was carried out with each strain under its
optimum conditions. The pretreated corncob samples were further
hydrolyzed to produce reducing glucose with low amounts of
commercial cellulase (25 U·g-1 corncob) from Aspergillus niger. The
corncob samples were determined for composition change by X-ray
diffraction (XRD), Fourier transform infrared spectroscopy (FTIR),
and scanning electron microscope (SEM). According to the results,
the microbial pretreatment with fungus, P. sordida SK7 was the most
effective for enhancing enzymatic hydrolysis, approximately, 40%
improvement.
Abstract: Sarkhoon gas plant, located in south of Iran, has been installed to removal H2S contained in a high pressure natural gas stream. The solvent used for the H2S removal from gaseous stream is 34% by weight (wt%) Di-ethanol amine (DEA) solutions. Due to increasing concentration of heat stable salt (HSS) in solvent, corrosivity of amine solution had been increased. Reports indicated that there was corrosion on the shell of regeneration column. Because source formation of HSS was unknown, we decided to control the amount of HSS at the limit less than 3% wt amine solvent. Therefore, two small columns were filled by strong anionic base and carbon active, and then polluted amine was passed through beds. Finally a temporary amine recovery package on industrial scale was made based on laboratory’s results. From economical point of view we could save $700000 beside corrosion occurrence of the stripping column has been vigorously decreased.
Abstract: Methanol-to-olefins coupled with transformation of
coal or natural gas to methanol gives an interesting and promising way
to produce ethylene and propylene. To investigate solid concentration
in gas-solid fluidized bed for methanol-to-olefins process catalyzed by
SAPO-34, a cold model experiment system is established in this paper.
The system comprises a gas distributor in a 300mm internal diameter
and 5000mm height acrylic column, the fiber optic probe system and
series of cyclones. The experiments are carried out at ambient
conditions and under different superficial gas velocity ranging from
0.3930m/s to 0.7860m/s and different initial bed height ranging from
600mm to 1200mm. The effects of radial distance, axial distance,
superficial gas velocity, initial bed height on solid concentration in the
bed are discussed. The effects of distributor shape and porosity on
solid concentration are also discussed. The time-averaged solid
concentration profiles under different conditions are obtained.
Abstract: The aim of the study was to investigate phytochemical
properties, antimicrobial activity and cytotoxicity of Aloe vera. The
phytochemical screening of the extracts of leaves of A. vera revealed
the presence of bioactive compounds such as alkaloids, tannins,
flavonoids phenolic compounds, and etc. with absence of cyanogenic
glycosides. Three different solvents such as methanol, ethanol and
Di-Methyl sulfoxide were used to screen the antimicrobial activity of
A. vera leaves against four human clinical pathogens by agar well
diffusion method. The maximum antibacterial activities were
observed in methanol extract followed by ethanol and Di-Methyl
sulfoxide. It was also found that remarkable antibacterial activities
with methanolic and ethanolic extracts of A. vera compared with the
standard antibiotic, tetracycline that was not active against E. coli
and S. boydii and supported the view that A. vera is a potent
antimicrobial agent compared with the conventional antibiotic.
Moreover, the brine shrimps (Artemia salina) toxicity test exhibited
LC50 value was 569.52 ppm. The resulting data indicated that the A.
vera plant have less toxic effects on brine shrimp. Hence, it is
signified that Aloe vera plant extract is safe to be used as an
antimicrobial agent.
Abstract: The traditional method for essential oil extraction from agarwood (Aquilaria Crassna) is to soak it in water and follow with hydrodistillation. The effect of various agarwood pretreatments: ethanol, acid, alkaline, enzymes, and ultrasound, and the effect of subcritical water extraction(SWE) was studied to compare with the traditional method. The major compositions of agarwood oil from hydrodistillation were aroma compounds as follow: aristol-9-en-8- one (21.53%), selina-3, 7(11)-diene (12.96%), τ-himachalene (9.28%), β-guaiene (5.79%), hexadecanoic acid (4.90%) and guaia- 3,9-diene (4.21%). Whereas agarwood oil from pretreatments with ethanol and ultrasound, and SWE got fatty acid compounds. Extraction of agarwood oil using these pretreatments could improve the agarwood oil yields up to 2 times that of the traditional method. The components of the pretreated sample with diluted acid (H2SO4) at pH 4 gave quite similar results as the traditional method. Therefore, the enhancement of essential oil from agarwood depends on requirement of type of extracted oil that involved extraction methods.
Abstract: β-Glucosidase is an important enzyme for production
of ethanol from lignocellulose. With hydrolytic activity on
cellooligosaccharides, especially cellobiose, β-glucosidase removes
product inhibitory effect on cellulases and forms fermentable sugars.
In this study, β-glucosidase encoding gene (BGL1) from traditional
starter yeast Saccharomycosis fibuligera BMQ908 was cloned and
expressed in Pichia pastoris. BGL1 of S. fibuligera BMQ 908 shared
98% nucleotide homology with the closest GenBank sequence
(M22475) but identity in amino-acid sequences of catalytic domains.
Recombinant plasmid pPICZαA/BGL1 containing the sequence
encoding BGL1 mature protein and α-factor secretion signal was
constructed and transformed into methylotrophic yeast P. pastoris by
electroporation. The recombinant strain produced single extracellular
protein with molecular weight of 120 kDa and cellobiase activity of
60 IU/ml. The optimum pH of the recombinant β-glucosidase was 5.0
and the optimum temperature was 50°C.