Abstract: This paper considers the problem of Null-Steering beamforming using Neural Network (NN) approach for antenna array system. Two cases are presented. First, unlike the other authors, the estimated Direction Of Arrivals (DOAs) are used for antenna array weights NN-based determination and the imprecise DOAs estimations are taken into account. Second, the blind null-steering beamforming is presented. In this case the antenna array outputs are presented at the input of the NN without DOAs estimation. The results of computer simulations will show much better relative mean error performances of the first NN approach compared to the NNbased blind beamforming.
Abstract: Optical burst switching (OBS) has been proposed to
realize the next generation Internet based on the wavelength division
multiplexing (WDM) network technologies. In the OBS, the burst
contention is one of the major problems. The deflection routing has
been designed for resolving the problem. However, the deflection
routing becomes difficult to prevent from the burst contentions as the
network load becomes high. In this paper, we introduce a flow rate
control methods to reduce burst contentions. We propose new flow
rate control methods based on the leaky bucket algorithm and
deflection routing, i.e. separate leaky bucket deflection method, and
dynamic leaky bucket deflection method. In proposed methods, edge
nodes which generate data bursts carry out the flow rate control
protocols. In order to verify the effectiveness of the flow rate control in
OBS networks, we show that the proposed methods improve the
network utilization and reduce the burst loss probability through
computer simulations.
Abstract: This work focuses on analysis of classical heat transfer equation regularized with Maxwell-Cattaneo transfer law. Computer simulations are performed in MATLAB environment. Numerical experiments are first developed on classical Fourier equation, then Maxwell-Cattaneo law is considered. Corresponding equation is regularized with a balancing diffusion term to stabilize discretizing scheme with adjusted time and space numerical steps. Several cases including a convective term in model equations are discussed, and results are given. It is shown that limiting conditions on regularizing parameters have to be satisfied in convective case for Maxwell-Cattaneo regularization to give physically acceptable solutions. In all valid cases, uniform convergence to solution of initial heat equation with Fourier law is observed, even in nonlinear case.
Abstract: Most of the commonly used blind equalization algorithms are based on the minimization of a nonconvex and nonlinear cost function and a neural network gives smaller residual error as compared to a linear structure. The efficacy of complex valued feedforward neural networks for blind equalization of linear and nonlinear communication channels has been confirmed by many studies. In this paper we present two neural network models for blind equalization of time-varying channels, for M-ary QAM and PSK signals. The complex valued activation functions, suitable for these signal constellations in time-varying environment, are introduced and the learning algorithms based on the CMA cost function are derived. The improved performance of the proposed models is confirmed through computer simulations.
Abstract: Piezoelectric transformers are electronic devices made
from piezoelectric materials. The piezoelectric transformers as the
name implied are used for changing voltage signals from one level to another. Electrical energy carried with signals is transferred by means of mechanical vibration. Characterizing in both electrical and
mechanical properties leads to extensively use and efficiency enhancement of piezoelectric transformers in various applications. In
this paper, study and analysis of electrical and mechanical properties of multi-layer piezoelectric transformers in forms of potential and
displacement distribution throughout the volume, respectively. This
paper proposes a set of quasi-static mathematical model of electromechanical
coupling for piezoelectric transformer by using a set of
partial differential equations. Computer-based simulation utilizing the three-dimensional finite element method (3-D FEM) is exploited
as a tool for visualizing potentials and displacements distribution
within the multi-layer piezoelectric transformer. This simulation was
conducted by varying a number of layers. In this paper 3, 5 and 7 of
the circular ring type were used. The computer simulation based on
the use of the FEM has been developed in MATLAB programming environment.
Abstract: This paper considers the autonomous navigation
problem of multiple n-link nonholonomic mobile manipulators within
an obstacle-ridden environment. We present a set of nonlinear
acceleration controllers, derived from the Lyapunov-based control
scheme, which generates collision-free trajectories of the mobile
manipulators from initial configurations to final configurations in a
constrained environment cluttered with stationary solid objects of
different shapes and sizes. We demonstrate the efficiency of the
control scheme and the resulting acceleration controllers of the
mobile manipulators with results through computer simulations of an
interesting scenario.
Abstract: The mechanical properties of granular solids are
dependent on the flow of stresses from one particle to another
through inter-particle contact. Although some experimental methods
have been used to study the inter-particle contacts in the past,
preliminary work with these techniques indicated that they do not
have the necessary resolution to distinguish between those contacts
that transmit the load and those that do not, especially for systems
with a wide distribution of particle sizes. In this research, computer
simulations are used to study the nature and distribution of contacts
in a compact with wide particle size distribution, representative of
aggregate size distribution used in asphalt pavement construction.
The packing fraction, the mean number of contacts and the
distribution of contacts were studied for different scenarios. A
methodology to distinguish and compute the fraction of load-bearing
particles and the fraction of space-filling particles (particles that do
not transmit any force) is needed for further investigation.
Abstract: In contrast to existing of calculation of temperature field of a profile part a blade with convective cooling which are not taking into account multi connective in a broad sense of this term, we develop mathematical models and highly effective combination (BIEM AND FDM) numerical methods from the point of view of a realization on the PC. The theoretical substantiation of these methods is proved by the appropriate theorems.
Abstract: This paper presents the mathematical model of electric field and magnetic field in transmission system, which performs in second-order partial differential equation. This research has conducted analyzing the electromagnetic field radiating to atmosphere around the transmission line, when there is the transmission line transposition in case of long distance distribution. The six types of 500 kV transposed HV transmission line with double circuit will be considered. The computer simulation is applied finite element method that is developed by MATLAB program. The problem is considered to two dimensions, which is time harmonic system with the graphical performance of electric field and magnetic field. The impact from simulation of six types long distance distributing transposition will not effect changing of electric field and magnetic field which surround the transmission line.
Abstract: Quality control charts are very effective in detecting
out of control signals but when a control chart signals an out of
control condition of the process mean, searching for a special cause
in the vicinity of the signal time would not always lead to prompt
identification of the source(s) of the out of control condition as the
change point in the process parameter(s) is usually different from the
signal time. It is very important to manufacturer to determine at what
point and which parameters in the past caused the signal. Early
warning of process change would expedite the search for the special
causes and enhance quality at lower cost. In this paper the quality
variables under investigation are assumed to follow a multivariate
normal distribution with known means and variance-covariance
matrix and the process means after one step change remain at the new
level until the special cause is being identified and removed, also it is
supposed that only one variable could be changed at the same time.
This research applies artificial neural network (ANN) to identify the
time the change occurred and the parameter which caused the change
or shift. The performance of the approach was assessed through a
computer simulation experiment. The results show that neural
network performs effectively and equally well for the whole shift
magnitude which has been considered.
Abstract: In this paper, Selective Adaptive Parallel Interference Cancellation (SA-PIC) technique is presented for Multicarrier Direct Sequence Code Division Multiple Access (MC DS-CDMA) scheme. The motivation of using SA-PIC is that it gives high performance and at the same time, reduces the computational complexity required to perform interference cancellation. An upper bound expression of the bit error rate (BER) for the SA-PIC under Rayleigh fading channel condition is derived. Moreover, the implementation complexities for SA-PIC and Adaptive Parallel Interference Cancellation (APIC) are discussed and compared. The performance of SA-PIC is investigated analytically and validated via computer simulations.
Abstract: This paper presents recent work on the improvement
of the robotics vision based control strategy for underwater pipeline
tracking system. The study focuses on developing image processing
algorithms and a fuzzy inference system for the analysis of the
terrain. The main goal is to implement the supervisory fuzzy learning
control technique to reduce the errors on navigation decision due to
the pipeline occlusion problem. The system developed is capable of
interpreting underwater images containing occluded pipeline, seabed
and other unwanted noise. The algorithm proposed in previous work
does not explore the cooperation between fuzzy controllers,
knowledge and learnt data to improve the outputs for underwater
pipeline tracking. Computer simulations and prototype simulations
demonstrate the effectiveness of this approach. The system accuracy
level has also been discussed.
Abstract: This paper was aimed at developing a computer aided
design and manufacturing system for spatial cylindrical cams. In the
proposed system, a milling tool with a diameter smaller than that of the
roller, instead of the standard cutter for traditional machining process,
was used to generate the tool path for spatial cams. To verify the
feasibility of the proposed method, a multi-axis machining simulation
software was further used to simulate the practical milling operation of
spatial cams. It was observed from computer simulation that the tool
path of small-sized cutter were within the motion range of a standard
cutter, no occurrence of overcutting. Examination of a finished cam
component clearly verifies the accuracy of the tool path generated for
small-sized milling tool. It is believed that the use of small-sized cutter
for the machining of the spatial cylindrical cams can generate a better
surface morphology with higher accuracy. The improvement in
efficiency and cost for the manufacturing of the spatial cylindrical cam
can be expected through the proposed method.
Abstract: Power loss reduction is one of the main targets in power industry and so in this paper, the problem of finding the optimal configuration of a radial distribution system for loss reduction is considered. Optimal reconfiguration involves the selection of the best set of branches to be opened ,one each from each loop, for reducing resistive line losses , and reliving overloads on feeders by shifting the load to adjacent feeders. However ,since there are many candidate switching combinations in the system ,the feeder reconfiguration is a complicated problem. In this paper a new approach is proposed based on a simple optimum loss calculation by determining optimal trees of the given network. From graph theory a distribution network can be represented with a graph that consists a set of nodes and branches. In fact this problem can be viewed as a problem of determining an optimal tree of the graph which simultaneously ensure radial structure of each candidate topology .In this method the refined genetic algorithm is also set up and some improvements of algorithm are made on chromosome coding. In this paper an implementation of the algorithm presented by [7] is applied by modifying in load flow program and a comparison of this method with the proposed method is employed. In [7] an algorithm is proposed that the choice of the switches to be opened is based on simple heuristic rules. This algorithm reduce the number of load flow runs and also reduce the switching combinations to a fewer number and gives the optimum solution. To demonstrate the validity of these methods computer simulations with PSAT and MATLAB programs are carried out on 33-bus test system. The results show that the performance of the proposed method is better than [7] method and also other methods.
Abstract: Network reconfiguration in distribution system is realized by changing the status of sectionalizing switches to reduce the power loss in the system. This paper presents a new method which applies an artificial bee colony algorithm (ABC) for determining the sectionalizing switch to be operated in order to solve the distribution system loss minimization problem. The ABC algorithm is a new population based metaheuristic approach inspired by intelligent foraging behavior of honeybee swarm. The advantage of ABC algorithm is that it does not require external parameters such as cross over rate and mutation rate as in case of genetic algorithm and differential evolution and it is hard to determine these parameters in prior. The other advantage is that the global search ability in the algorithm is implemented by introducing neighborhood source production mechanism which is a similar to mutation process. To demonstrate the validity of the proposed algorithm, computer simulations are carried out on 14, 33, and 119-bus systems and compared with different approaches available in the literature. The proposed method has outperformed the other methods in terms of the quality of solution and computational efficiency.
Abstract: The paper deals with the estimation of amplitude and phase of an analogue multi-harmonic band-limited signal from irregularly spaced sampling values. To this end, assuming the signal fundamental frequency is known in advance (i.e., estimated at an independent stage), a complexity-reduced algorithm for signal reconstruction in time domain is proposed. The reduction in complexity is achieved owing to completely new analytical and summarized expressions that enable a quick estimation at a low numerical error. The proposed algorithm for the calculation of the unknown parameters requires O((2M+1)2) flops, while the straightforward solution of the obtained equations takes O((2M+1)3) flops (M is the number of the harmonic components). It is applied in signal reconstruction, spectral estimation, system identification, as well as in other important signal processing problems. The proposed method of processing can be used for precise RMS measurements (for power and energy) of a periodic signal based on the presented signal reconstruction. The paper investigates the errors related to the signal parameter estimation, and there is a computer simulation that demonstrates the accuracy of these algorithms.
Abstract: A new approach for the improvement of coding gain
in channel coding using Advanced Encryption Standard (AES) and
Maximum A Posteriori (MAP) algorithm is proposed. This new
approach uses the avalanche effect of block cipher algorithm AES
and soft output values of MAP decoding algorithm. The performance
of proposed approach is evaluated in the presence of Additive White
Gaussian Noise (AWGN). For the verification of proposed approach,
computer simulation results are included.
Abstract: Background noise is particularly damaging to speech
intelligibility for people with hearing loss especially for sensorineural
loss patients. Several investigations on speech intelligibility have
demonstrated sensorineural loss patients need 5-15 dB higher SNR
than the normal hearing subjects. This paper describes Discrete
Cosine Transform Power Normalized Least Mean Square algorithm
to improve the SNR and to reduce the convergence rate of the LMS
for Sensory neural loss patients. Since it requires only real arithmetic,
it establishes the faster convergence rate as compare to time domain
LMS and also this transformation improves the eigenvalue
distribution of the input autocorrelation matrix of the LMS filter.
The DCT has good ortho-normal, separable, and energy compaction
property. Although the DCT does not separate frequencies, it is a
powerful signal decorrelator. It is a real valued function and thus
can be effectively used in real-time operation. The advantages of
DCT-LMS as compared to standard LMS algorithm are shown via
SNR and eigenvalue ratio computations. . Exploiting the symmetry
of the basis functions, the DCT transform matrix [AN] can be
factored into a series of ±1 butterflies and rotation angles. This
factorization results in one of the fastest DCT implementation. There
are different ways to obtain factorizations. This work uses the fast
factored DCT algorithm developed by Chen and company. The
computer simulations results show superior convergence
characteristics of the proposed algorithm by improving the SNR at
least 10 dB for input SNR less than and equal to 0 dB, faster
convergence speed and better time and frequency characteristics.
Abstract: One of the main image representations in Mathematical Morphology is the 3D Shape Decomposition Representation, useful for Image Compression and Representation,and Pattern Recognition. The 3D Morphological Shape Decomposition representation can be generalized a number of times,to extend the scope of its algebraic characteristics as much as possible. With these generalizations, the Morphological Shape Decomposition 's role to serve as an efficient image decomposition tool is extended to grayscale images.This work follows the above line, and further develops it. Anew evolutionary branch is added to the 3D Morphological Shape Decomposition's development, by the introduction of a 3D Multi Structuring Element Morphological Shape Decomposition, which permits 3D Morphological Shape Decomposition of 3D binary images (grayscale images) into "multiparameter" families of elements. At the beginning, 3D Morphological Shape Decomposition representations are based only on "1 parameter" families of elements for image decomposition.This paper addresses the gray scale inter frame interpolation by means of mathematical morphology. The new interframe interpolation method is based on generalized morphological 3D Shape Decomposition. This article will present the theoretical background of the morphological interframe interpolation, deduce the new representation and show some application examples.Computer simulations could illustrate results.
Abstract: In this paper, a delayed prototype model is studied. Regarding the delay as a bifurcation parameter, we prove that a sequence of Hopf bifurcations will occur at the positive equilibrium when the delay increases. Using the normal form method and center manifold theory, some explicit formulae are worked out for determining the stability and the direction of the bifurcated periodic solutions. Finally, Computer simulations are carried out to explain some mathematical conclusions.