Abstract: This paper presents the research agenda that has been proposed to develop an integrated model to explain technology adoption of SMEs in Malaysia. SMEs form over 90% of all business entities in Malaysia and they have been contributing to the development of the nation. Technology adoption has been a thorn issue among SMEs as they require big outlay which might not be available to the SMEs. Although resource has been an issue among SMEs they cannot lie low and ignore the technological advancements that are taking place at a rapid pace. With that in mind this paper proposes a model to explain the technology adoption issue among SMEs.
Abstract: According to the masonry standard the compressive
strength is basically dependent on factors such as the mortar strength
and the relative values of unit and mortar strength. However
interlocking brick has none or less use of mortar. Therefore there is a need to investigate the behavior of masonry walls using interlocking
bricks. In this study a series of tests have been conducted; physical
properties and compressive strength of brick units and masonry walls
were constructed from interlocking bricks and tested under constant
vertical load at different eccentricities. The purpose of the
experimental investigations is to obtain the force displacement curves, analyze the behavior of masonry walls. The results showed
that the brick is categorized as common brick (BS 3921:1985) and severe weathering grade (ASTM C62). The maximum compressive stress of interlocking brick wall is 3.6 N/mm2 and fulfilled the requirement of standard for residential building.
Abstract: This paper focuses on PSS/E modeling of wind farms
of Doubly-fed Induction Generator (DFIG) type and their impact on
issues of power system operation. Since Wind Turbine Generators
(WTG) don-t have the same characteristics as synchronous
generators, the appropriate modeling of wind farms is essential for
transmission system operators to analyze the best options of
transmission grid reinforcements as well as to evaluate the wind
power impact on reliability and security of supply. With the high
excepted penetration of wind power into the power system a
simultaneous loss of Wind Farm generation will put at risk power
system security and reliability. Therefore, the main wind grid code
requirements concern the fault ride through capability and frequency
operation range of wind turbines. In case of grid faults wind turbines
have to supply a definite reactive power depending on the
instantaneous voltage and to return quickly to normal operation.
Abstract: Background noise is particularly damaging to speech
intelligibility for people with hearing loss especially for sensorineural
loss patients. Several investigations on speech intelligibility have
demonstrated sensorineural loss patients need 5-15 dB higher SNR
than the normal hearing subjects. This paper describes Discrete
Cosine Transform Power Normalized Least Mean Square algorithm
to improve the SNR and to reduce the convergence rate of the LMS
for Sensory neural loss patients. Since it requires only real arithmetic,
it establishes the faster convergence rate as compare to time domain
LMS and also this transformation improves the eigenvalue
distribution of the input autocorrelation matrix of the LMS filter.
The DCT has good ortho-normal, separable, and energy compaction
property. Although the DCT does not separate frequencies, it is a
powerful signal decorrelator. It is a real valued function and thus
can be effectively used in real-time operation. The advantages of
DCT-LMS as compared to standard LMS algorithm are shown via
SNR and eigenvalue ratio computations. . Exploiting the symmetry
of the basis functions, the DCT transform matrix [AN] can be
factored into a series of ±1 butterflies and rotation angles. This
factorization results in one of the fastest DCT implementation. There
are different ways to obtain factorizations. This work uses the fast
factored DCT algorithm developed by Chen and company. The
computer simulations results show superior convergence
characteristics of the proposed algorithm by improving the SNR at
least 10 dB for input SNR less than and equal to 0 dB, faster
convergence speed and better time and frequency characteristics.
Abstract: The error diffusion method generates worm artifacts,
and weakens the edge of the halftone image when the continuous gray
scale image is reproduced by a binary image. First, to enhance the
edges, we propose the edge-enhancing filter by considering the
quantization error information and gradient of the neighboring pixels.
Furthermore, to remove worm artifacts often appearing in a halftone
image, we add adaptively random noise into the weights of an error
filter.
Abstract: Advancements in the field of artificial intelligence
(AI) made during this decade have forever changed the way we look
at automating spacecraft subsystems including the electrical power
system. AI have been used to solve complicated practical problems
in various areas and are becoming more and more popular nowadays.
In this paper, a mathematical modeling and MATLAB–SIMULINK
model for the different components of the spacecraft power system is
presented. Also, a control system, which includes either the Neural
Network Controller (NNC) or the Fuzzy Logic Controller (FLC) is
developed for achieving the coordination between the components of
spacecraft power system as well as control the energy flows. The
performance of the spacecraft power system is evaluated by
comparing two control systems using the NNC and the FLC.
Abstract: Social networking is one of the most successful and popular tools to emerge from the Web 2.0 era. However, the increased interconnectivity and access to peoples- personal lives and information has created a plethora of opportunities for the nefarious side of human nature to manifest. This paper categorizes and describes the major types of anti-social behavior and criminal activity that can arise through undisciplined use and/or misuse of social media. We specifically address identity theft, misrepresentation of information posted, cyber bullying, children and social networking, and social networking in the work place. Recommendations are provided for how to reduce the risk of being the victim of a crime or engaging in embarrassing behavior that could irrevocably harm one-s reputation either professionally or personally. We also discuss what responsibilities social networking companies have to protect their users and also what law enforcement and policy makers can do to help alleviate the problems.
Abstract: In nature, electromagnetic fields always appear like
atmosphere static electric field, the earth's static magnetic field and
the wide-rang frequency electromagnetic field caused by lightening.
However, besides natural electromagnetic fields (EMF), today human
beings are mostly exposed to artificial electromagnetic fields due to
technology progress and outspread use of electrical devices. To
evaluate nuisance of EMF, it is necessary to know field intensity for
every frequency which appears and compare it with allowed values.
Low frequency EMF-s around transmission and distribution lines are
time-varying quasi-static electromagnetic fields which have
conservative component of low frequency electrical field caused by
charges and eddy component of low frequency magnetic field caused
by currents. Displacement current or field delay are negligible, so
energy flow in quasi-static EMF involves diffusion, analog like heat
transfer. Electrical and magnetic field can be analyzed separately.
This paper analysis the numerical calculations in ELF-400 software
of EMF in distribution substation in shopping center. Analyzing the
results it is possible to specify locations exposed to the fields and
give useful suggestion to eliminate electromagnetic effect or reduce it
on acceptable level within the non-ionizing radiation norms and
norms of protection from EMF.
Abstract: A suspension bridge is the most suitable type of structure for a long-span bridge due to rational use of structural materials. Increased deformability, which is conditioned by appearance of the elastic and kinematic displacements, is the major disadvantage of suspension bridges. The problem of increased kinematic displacements under the action of non-symmetrical load can be solved by prestressing. The prestressed suspension bridge with the span of 200 m was considered as an object of investigations. The cable truss with the cross web was considered as the main load carrying structure of the prestressed suspension bridge. The considered cable truss was optimized by 47 variable factors using Genetic algorithm and FEM program ANSYS. It was stated, that the maximum total displacements are reduced up to 29.9% by using of the cable truss with the rational characteristics instead of the single cable in the case of the worst situated load.
Abstract: Thermal load calculations have been performed for
multi-layered walls that are composed of three different parts; a
common (sand and cement) plaster, and two types of locally
produced soft and hard bricks. The masonry construction of these
layered walls was based on concrete-backed stone masonry made of
limestone bricks joined by mortar. These multilayered walls are
forming the outer walls of the building envelope of a typical Libyan
house. Based on the periodic seasonal weather conditions, within the
Libyan cost region during summer and winter, measured thermal
conductivity values were used to implement such seasonal variation
of heat flow and the temperature variations through the walls. The
experimental measured thermal conductivity values were obtained
using the Hot Disk technique. The estimation of the thermal
resistance of the wall layers ( R-values) is based on measurements
and calculations. The numerical calculations were done using a
simplified analytical model that considers two different wall
constructions which are characteristics of such houses. According to
the obtained results, the R-values were quite low and therefore,
several suggestions have been proposed to improve the thermal
loading performance that will lead to a reasonable human comfort
and reduce energy consumption.
Abstract: Analytical seismic response of multi-story building
supported on base isolation system is investigated under real
earthquake motion. The superstructure is idealized as a shear type
flexible building with lateral degree-of-freedom at each floor. The
force-deformation behaviour of the isolation system is modelled by
the bi-linear behaviour which can be effectively used to model all
isolation systems in practice. The governing equations of motion of
the isolated structural system are derived. The response of the system
is obtained numerically by step-by-method under three real recorded
earthquake motions and pulse motions associated in the near-fault
earthquake motion. The variation of the top floor acceleration, interstory
drift, base shear and bearing displacement of the isolated
building is studied under different initial stiffness of the bi-linear
isolation system. It was observed that the high initial stiffness of the
isolation system excites higher modes in base-isolated structure and
generate floor accelerations and story drift. Such behaviour of the
base-isolated building especially supported on sliding type of
isolation systems can be detrimental to sensitive equipment installed
in the building. On the other hand, the bearing displacement and base
shear found to reduce marginally with the increase of the initial
stiffness of the initial stiffness of the isolation system. Further, the
above behaviour of the base-isolated building was observed for
different parameters of the bearing (i.e. post-yield stiffness and
characteristic strength) and earthquake motions (i.e. real time history
as well as pulse type motion).
Abstract: The new status generated by technological advancements and changes in the global economy raises important issues on how communities and organisations need to innovate upon their traditional processes in order to adapt to the challenges of the Knowledge Society. The DialogoS+ European project aims to study the role of and promote social dialogue in the banking sector, strengthen the link between old and new members and make social dialogue at the European level a force for innovation and change, also given the context of the international crisis emerging in 2008- 2009. Under the scope of DialogoS+, this paper describes how the community of Europe-s banking sector trade unions attempted to adapt to the challenges of the Knowledge Society by exploiting the benefits of new channels of communication, learning, knowledge generation and diffusion focusing on the concept of roadmapping. Important dimensions of social dialogue such as collective bargaining and working conditions are addressed.
Abstract: Advancement in Artificial Intelligence has lead to the
developments of various “smart" devices. Character recognition
device is one of such smart devices that acquire partial human
intelligence with the ability to capture and recognize various
characters in different languages. Firstly multiscale neural training
with modifications in the input training vectors is adopted in this
paper to acquire its advantage in training higher resolution character
images. Secondly selective thresholding using minimum distance
technique is proposed to be used to increase the level of accuracy of
character recognition. A simulator program (a GUI) is designed in
such a way that the characters can be located on any spot on the
blank paper in which the characters are written. The results show that
such methods with moderate level of training epochs can produce
accuracies of at least 85% and more for handwritten upper case
English characters and numerals.
Abstract: Fisheries management all around the world is
hampered by the lack, or poor quality, of critical data on fish
resources and fishing operations. The main reasons for the chronic
inability to collect good quality data during fishing operations is the
culture of secrecy common among fishers and the lack of modern
data gathering technology onboard most fishing vessels. In response,
OLRAC-SPS, a South African company, developed fisheries datalogging
software (eLog in short) and named it Olrac. The Olrac eLog
solution is capable of collecting, analysing, plotting, mapping,
reporting, tracing and transmitting all data related to fishing
operations. Olrac can be used by skippers, fleet/company managers,
offshore mariculture farmers, scientists, observers, compliance
inspectors and fisheries management authorities. The authors believe
that using eLog onboard fishing vessels has the potential to
revolutionise the entire process of data collection and reporting
during fishing operations and, if properly deployed and utilised,
could transform the entire commercial fleet to a provider of good
quality data and forever change the way fish resources are managed.
In addition it will make it possible to trace catches back to the actual
individual fishing operation, to improve fishing efficiency and to
dramatically improve control of fishing operations and enforcement
of fishing regulations.
Abstract: Based on the homotopy perturbation method (HPM)
and Padé approximants (PA), approximate and exact solutions are
obtained for cubic Boussinesq and modified Boussinesq equations.
The obtained solutions contain solitary waves, rational solutions.
HPM is used for analytic treatment to those equations and PA for
increasing the convergence region of the HPM analytical solution.
The results reveal that the HPM with the enhancement of PA is a
very effective, convenient and quite accurate to such types of partial
differential equations.
Abstract: This paper outlines the development of a learning retrieval agent. Task of this agent is to extract knowledge of the Active Semantic Network in respect to user-requests. Based on a reinforcement learning approach, the agent learns to interpret the user-s intention. Especially, the learning algorithm focuses on the retrieval of complex long distant relations. Increasing its learnt knowledge with every request-result-evaluation sequence, the agent enhances his capability in finding the intended information.
Abstract: Toughening of polyamide 6 (PA6)/ Nanoclay (NC) nanocomposites with styrene-ethylene/butadiene-styrene copolymer (SEBS) using maleated styrene-ethylene/butadiene-styrene copolymer (mSEBS)/ as a compatibilizer were investigated by blending them in a co-rotating twin-screw extruder. Response surface method of experimental design was used for optimizing the material and processing parameters. Effect of four factors, including SEBS, mSEBS and NC contents as material variables and order of mixing as a processing factor, on toughness of hybrid nanocomposites were studied. All the prepared samples showed ductile behavior and low temperature Izod impact toughness of some of the hybrid nanocomposites demonstrated 900% improvement compared to the PA6 matrix while the modulus showed maximum enhancement of 20% compared to the pristine PA6 resin.
Abstract: Advent enhancements in the field of computing have
increased massive use of web based electronic documents. Current
Copyright protection laws are inadequate to prove the ownership for
electronic documents and do not provide strong features against
copying and manipulating information from the web. This has
opened many channels for securing information and significant
evolutions have been made in the area of information security.
Digital Watermarking has developed into a very dynamic area of
research and has addressed challenging issues for digital content.
Watermarking can be visible (logos or signatures) and invisible
(encoding and decoding). Many visible watermarking techniques
have been studied for text documents but there are very few for web
based text. XML files are used to trade information on the internet
and contain important information. In this paper, two invisible
watermarking techniques using Synonyms and Acronyms are
proposed for XML files to prove the intellectual ownership and to
achieve the security. Analysis is made for different attacks and
amount of capacity to be embedded in the XML file is also noticed.
A comparative analysis for capacity is also made for both methods.
The system has been implemented using C# language and all tests are
made practically to get the results.
Abstract: Prestressing in structure increases ratio of load-bearing capacity to weight. Suspendomes are single-layer braced domes reinforced with cable and strut. Prestressing of cables alter value and distribution of stress in structure. In this study two configuration, diamatic and lamella domes is selected. Investigated domes have span of 100m with rise-to-span ratios of 0.1, 0.2, and 0.3. Single layer domes loaded under service load combinations according to ISO code. After geometric nonlinear analysis, models are designed with tubular and I-shaped sections then reinforced with cable and strut and converted to suspendomes. Displacements and stresses of some groups of nodes and elements in all of single-layer domes and suspendomes for three load combinations, symmetric snow, asymmetric snow and wind are compared. Variation due to suspending system is investigated. Suspendomes are redesigned and minimum possible weight after addition of cable and strut is obtained.
Abstract: Economic crime (i.e. corporate fraud) has a
significant impact on business. This study analyzes the fraud cases
reported by the Malaysian Securities Commission. Frauds involving
market manipulation and/or illegal share trading are the most
common types of fraud reported over the 6 years analyzed. The
highest number of frauds reported involved investment and fund
holding companies. Alarmingly the results indicate quite a high
number of frauds cases are committed by management. The higher
number of Chinese perpetrators may be due to fact that they are the
dominant group in Malaysian business. The result also shows that
more than half of companies involved with fraud are privately held
companies in the investment/fund/finance sector. The results of this
study highlight general characteristic of perpetrators (person and
company) that commit fraud which could help the regulators in their
monitoring and enforcement activities. To investors, this would help
in analyzing their business investment or portfolio risk.