Abstract: Active Vibration Control (AVC) is an important
problem in structures. One of the ways to tackle this problem is to
make the structure smart, adaptive and self-controlling. The objective
of active vibration control is to reduce the vibration of a system by
automatic modification of the system-s structural response. This
paper features the modeling and design of a Periodic Output
Feedback (POF) control technique for the active vibration control of
a flexible Timoshenko cantilever beam for a multivariable case with
2 inputs and 2 outputs by retaining the first 2 dominant vibratory
modes using the smart structure concept. The entire structure is
modeled in state space form using the concept of piezoelectric
theory, Timoshenko beam theory, Finite Element Method (FEM) and
the state space techniques. Simulations are performed in MATLAB.
The effect of placing the sensor / actuator at 2 finite element
locations along the length of the beam is observed. The open loop
responses, closed loop responses and the tip displacements with and
without the controller are obtained and the performance of the smart
system is evaluated for active vibration control.
Abstract: This paper has been investigated a technique that predicts the performance of a bar-type unimorph piezoelectric vibration actuator depending on the frequency. This paper has been proposed an equivalent circuit that can be easily analyzed for the bar-type unimorph piezoelectric vibration actuator. In the dynamic analysis, rigidity and resonance frequency, which are important mechanical elements, were derived using the basic beam theory. In the equivalent circuit analysis, the displacement and bandwidth of the piezoelectric vibration actuator depending on the frequency were predicted. Also, for the reliability of the derived equations, the predicted performance depending on the shape change was compared with the result of a finite element analysis program.
Abstract: We present the development of a new underwater laser
cutting process in which a water-jet has been used along with the
laser beam to remove the molten material through kerf. The
conventional underwater laser cutting usually utilizes a high pressure
gas jet along with laser beam to create a dry condition in the cutting
zone and also to eject out the molten material. This causes a lot of gas
bubbles and turbulence in water, and produces aerosols and waste
gas. This may cause contamination in the surrounding atmosphere
while cutting radioactive components like burnt nuclear fuel. The
water-jet assisted underwater laser cutting process produces much
less turbulence and aerosols in the atmosphere. Some amount of
water vapor bubbles is formed at the laser-metal-water interface;
however, they tend to condense as they rise up through the
surrounding water. We present the design and development of a
water-jet assisted underwater laser cutting head and the parametric
study of the cutting of AISI 304 stainless steel sheets with a 2 kW
CW fiber laser. The cutting performance is similar to that of the gas
assist laser cutting; however, the process efficiency is reduced due to
heat convection by water-jet and laser beam scattering by vapor. This
process may be attractive for underwater cutting of nuclear reactor
components.
Abstract: Based on Rayleigh beam theory, the sub-impacts of a
free-free beam struck horizontally by a round-nosed rigid mass is
simulated by the finite difference method and the impact-separation
conditions. In order to obtain the sub-impact force, a uniaxial
compression elastic-plastic contact model is employed to analyze the
local deformation field on contact zone. It is found that the horizontal
impact is a complicated process including the elastic plastic
sub-impacts in sequence. There are two sub-zones of sub-impact. In
addition, it found that the elastic energy of the free-free beam is more
suitable for the Poisson collision hypothesis to explain compression
and recovery processes.
Abstract: This paper features the modeling and design of a Fast
Output Sampling (FOS) Feedback control technique for the Active
Vibration Control (AVC) of a smart flexible aluminium cantilever
beam for a Single Input Single Output (SISO) case. Controllers are
designed for the beam by bonding patches of piezoelectric layer as
sensor / actuator to the master structure at different locations along
the length of the beam by retaining the first 2 dominant vibratory
modes. The entire structure is modeled in state space form using the
concept of piezoelectric theory, Euler-Bernoulli beam theory, Finite
Element Method (FEM) and the state space techniques by dividing
the structure into 3, 4, 5 finite elements, thus giving rise to three
types of systems, viz., system 1 (beam divided into 3 finite
elements), system 2 (4 finite elements), system 3 (5 finite elements).
The effect of placing the sensor / actuator at various locations along
the length of the beam for all the 3 types of systems considered is
observed and the conclusions are drawn for the best performance and
for the smallest magnitude of the control input required to control the
vibrations of the beam. Simulations are performed in MATLAB. The
open loop responses, closed loop responses and the tip displacements
with and without the controller are obtained and the performance of
the proposed smart system is evaluated for vibration control.
Abstract: There is a acute water problem especially in the dry
season in and around Perundurai (Erode district, Tamil Nadu, India)
where there are more number of tannery units. Hence an attempt was
made to use the waste water from tannery industry for construction
purpose. The mechanical properties such as compressive strength,
tensile strength, flexural strength etc were studied by casting various
concrete specimens in form of cube, cylinders and beams etc and
were found to be satisfactory. Hence some special properties such as
chloride attack, sulphate attack and chemical attack are considered
and comparatively studied with the conventional potable water. In
this experimental study the results of specimens prepared by using
treated and untreated tannery effluent were compared with the
concrete specimens prepared by using potable water. It was observed
that the concrete had some reduction in strength while subjected to
chloride attack, sulphate attack and chemical attack. So admixtures
were selected and optimized in suitable proportion to counter act the
adverse effects and the results were found to be satisfactory.
Abstract: The spiral angle of the elementary cellulose fibril in
the wood cell wall, often called microfibril angle, (MFA). Microfibril
angle in hardwood is one of the key determinants of solid timber
performance due to its strong influence on the stiffness, strength,
shrinkage, swelling, thermal-dynamics mechanical properties and
dimensional stability of wood. Variation of MFA (degree) in the S2
layer of the cell walls among Acacia mangium trees was determined
using small-angle X-ray scattering (SAXS). The length and
orientation of the microfibrils of the cell walls in the irradiated
volume of the thin samples are measured using SAXS and optical
microscope for 3D surface measurement. The undetermined
parameters in the analysis are the MFA, (M) and the standard
deviation (σФ) of the intensity distribution arising from the wandering
of the fibril orientation about the mean value. Nine separate pairs of
values are determined for nine different values of the angle of the
incidence of the X-ray beam relative to the normal to the radial
direction in the sample. The results show good agreement. The
curve distribution of scattered intensity for the real cell wall structure
is compared with that calculated with that assembly of rectangular
cells with the same ratio of transverse to radial cell wall length. It is
demonstrated that for β = 45°, the peaks in the curve intensity
distribution for the real and the rectangular cells coincide. If this
peak position is Ф45, then the MFA can be determined from the
relation M = tan-1 (tan Ф45 / cos 45°), which is precise for rectangular
cells. It was found that 92.93% of the variation of MFA can be
attributed to the distance from pith to bark. Here we shall present our
results of the MFA in the cell wall with respect to its shape, structure
and the distance from pith to park as an important fast check and yet
accurate towards the quality of wood, its uses and application.
Abstract: The paper presents the optimization problem for the
multi-element synthetic transmit aperture method (MSTA) in
ultrasound imaging applications. The optimal choice of the transmit
aperture size is performed as a trade-off between the lateral
resolution, penetration depth and the frame rate. Results of the
analysis obtained by a developed optimization algorithm are
presented. Maximum penetration depth and the best lateral resolution
at given depths are chosen as the optimization criteria. The
optimization algorithm was tested using synthetic aperture data of
point reflectors simulated by Filed II program for Matlab® for the
case of 5MHz 128-element linear transducer array with 0.48 mm
pitch are presented. The visualization of experimentally obtained
synthetic aperture data of a tissue mimicking phantom and in vitro
measurements of the beef liver are also shown. The data were
obtained using the SonixTOUCH Research systemequipped with a
linear 4MHz 128 element transducerwith 0.3 mm element pitch, 0.28
mm element width and 70% fractional bandwidth was excited by one
sine cycle pulse burst of transducer's center frequency.
Abstract: This paper deals with a numerical analysis of the
transient response of composite beams with strain rate dependent
mechanical properties by use of a finite difference method. The
equations of motion based on Timoshenko beam theory are derived.
The geometric nonlinearity effects are taken into account with von
Kármán large deflection theory. The finite difference method in
conjunction with Newmark average acceleration method is applied to
solve the differential equations. A modified progressive damage
model which accounts for strain rate effects is developed based on
the material property degradation rules and modified Hashin-type
failure criteria and added to the finite difference model. The
components of the model are implemented into a computer code in
Mathematica 6. Glass/epoxy laminated composite beams with
constant and strain rate dependent mechanical properties under
dynamic load are analyzed. Effects of strain rate on dynamic
response of the beam for various stacking sequences, load and
boundary conditions are investigated.
Abstract: Thermoelastic temperature, displacement, and
stress in heat transfer during laser surface hardening are solved
in Eulerian formulation. In Eulerian formulations the heat flux
is fixed in space and the workpiece is moved through a control
volume. In the case of uniform velocity and uniform heat flux
distribution, the Eulerian formulations leads to a steady-state
problem, while the Lagrangian formulations remains transient.
In Eulerian formulations the reduction to a steady-state
problem increases the computational efficiency. In this study
also an analytical solution is developed for an uncoupled
transient heat conduction equation in which a plane slab is
heated by a laser beam. The thermal result of the numerical
model is compared with the result of this analytical model.
Comparing the results shows numerical solution for uncoupled
equations are in good agreement with the analytical solution.
Abstract: Design for Disassembly (DfD) aims to reuse the
structural components instead of demolition followed by recycling of
the demolition debris. This concept preserves the invested embodied
energy of materials, thus reducing inputs of new embodied energy
during materials reprocessing or remanufacturing. Both analytical and
experimental research on a proposed DfD beam-column connection
for use in residential apartments is currently investigated at the
National University of Singapore in collaboration with the Housing
and Development Board of Singapore. The present study reports on
the results of a numerical analysis of the proposed connection utilizing
finite element analysis. The numerical model was calibrated and
validated by comparison against experimental results. Results of a
parametric study will also be presented and discussed.
Abstract: In this work, the plate bending formulation of the boundary element method - BEM, based on the Reissner?s hypothesis, is extended to the analysis of plates reinforced by beams taking into account the membrane effects. The formulation is derived by assuming a zoned body where each sub-region defines a beam or a slab and all of them are represented by a chosen reference surface. Equilibrium and compatibility conditions are automatically imposed by the integral equations, which treat this composed structure as a single body. In order to reduce the number of degrees of freedom, the problem values defined on the interfaces are written in terms of their values on the beam axis. Initially are derived separated equations for the bending and stretching problems, but in the final system of equations the two problems are coupled and can not be treated separately. Finally are presented some numerical examples whose analytical results are known to show the accuracy of the proposed model.
Abstract: A research program is conducted to evaluate the
mechanical properties of Ultra High Performance Concrete, target
compressive strength at the age of 28 days being more than 150 MPa.
The methodology to develop such mix has been explained. The
material properties, mix design and curing regime are determined.
The material attributes are understood by studying the stress strain
behaviour of UHPC cylinders under uniaxial compressive loading.
The load –crack mouth opening displacement (cmod) of UHPC
beams, flexural strength and fracture energy was evaluated using
third point loading test. Compressive strength and Split tensile
strength results are determined to find out the compressive and tensile
behaviour. Residual strength parameters are presented vividly
explaining the flexural performance, toughness of concrete.Durability
studies were also done to compare the effect of fibre to that of a
control mix For all the studies the Mechanical properties were
evaluated by varying the percentage and aspect ratio of steel fibres
The results reflected that higher aspect ratio and fibre volume
produced drastic changes in the cube strength, cylinder strength, post
peak response, load-cmod, fracture energy flexural strength, split
tensile strength, residual strength and durability. In regards to null
application of UHPC in India, an initiative is undertaken to
comprehend the mechanical behaviour of UHPC, which will be vital
for longer run in commercialization for structural applications.
Abstract: The peculiarities of the nanoscale structure-phase
states formed after electroexplosive carburizing and subsequent
electron-beam treatment of technically pure titanium surface in different regimes are established by methods of transmission electron
diffraction microscopy and physical mechanisms are discussed. Electroexplosive carburizing leads to surface layer formation
(40 m thickness) with increased (in 3.5 times) microhardness. It consists of β-titanium, graphite (monocrystals 100-150 nm,
polycrystals 5-10 nm, amorphous particles 3-5nm), TiC (5-10 nm), β-Ti02 (2-20nm). After electron-beam treatment additionally increasing the microhardness the surface layer consists of TiC.
Abstract: This paper presents the source extraction system which can extract only target signals with constraints on source localization in on-line systems. The proposed system is a kind of methods for enhancing a target signal and suppressing other interference signals. But, the performance of proposed system is superior to any other methods and the extraction of target source is comparatively complete. The method has a beamforming concept and uses an improved time-frequency (TF) mask-based BSS algorithm to separate a target signal from multiple noise sources. The target sources are assumed to be in front and test data was recorded in a reverberant room. The experimental results of the proposed method was evaluated by the PESQ score of real-recording sentences and showed a noticeable speech enhancement.