Abstract: Properly sized capacitor banks are connected across induction motors for several reasons including power factor correction, reducing distortions, increasing capacity, etc. Total harmonic distortion (THD) and power factor (PF) are used in such cases to quantify the improvements obtained through connection of the external capacitor banks. On the other hand, one of the methods for assessing the motor internal condition is by the use of Park-s pattern analysis. In spite of taking adequate precautionary measures, the capacitor banks may sometimes malfunction. Such a minor fault in the capacitor bank is often not apparently discernible. This may however, give rise to substantial degradation of power factor correction performance and may also damage the supply profile. The case is more severe with the fact that the Park-s pattern gets distorted due to such external capacitor faults, and can give anomalous results about motor internal fault analyses. The aim of this paper is to present simulation and hardware laboratory test results to have an understanding of the anomalies in harmonic distortion and Park-s pattern analyses in induction motors due to capacitor bank defects.
Abstract: The seismic vulnerability of an urban area is of a great
deal for local authorities especially those facing earthquakes. So, it is
important to have an efficient tool to assess the vulnerability of
existing buildings. The use of the VIP (Vulnerability Index Program)
and the GIS (Geographic Information System) let us to identify the
most vulnerable districts of an urban area.
The use of the vulnerability index method lets us to assess the
vulnerability of the center town of Blida (Algeria) which is a
historical town and which has grown enormously during the last
decades. In this method, three levels of vulnerability are defined. The
GIS has been used to build a data base in order to perform different
thematic analyses. These analyses show the seismic vulnerability of
Blida.
Abstract: This paper studies mixed-mode fracture mechanics in
rock based on experimental and numerical analyses. Experiments
were performed on sharp-cracked specimens using the modified
Arcan specimen test loading device. The modified Arcan specimen
test was, in association with a special loading device, an appropriate
apparatus for experimental mixed-mode fracture analysis. By
varying the loading angle from 0° to 90°, pure mode-I, pure mode-II
and a wide range of mixed-mode data were obtained experimentally.
Using the finite element results, correction factors applied to the
rectangular fracture specimen. By employing experimentally
measured critical loads and the aid of the finite element method,
mixed-mode fracture toughness for the limestone under consideration
determined.
Abstract: This paper deals with analysis of flexural stiffness,
indentation and their energies in three point loading of sandwich
beams with composite faces from Eglass/epoxy and cores from
Polyurethane or PVC. Energy is consumed in three stages of
indentation in laminated beam, indentation of sandwich beam and
bending of sandwich beam. Theory of elasticity is chosen to present
equations for indentation of laminated beam, then these equations
have been corrected to offer better results. An analytical model has
been used assuming an elastic-perfectly plastic compressive behavior
of the foam core. Classical theory of beam is used to describe three
point bending. Finite element (FE) analysis of static indentation
sandwich beams is performed using the FE code ABAQUS. The
foam core is modeled using the crushable foam material model and
response of the foam core is experimentally characterized in uniaxial
compression.
Three point bending and indentation have been done
experimentally in two cases of low velocity and higher velocity
(quasi-impact) of loading. Results can describe response of beam in
terms of core and faces thicknesses, core material, indentor diameter,
energy absorbed, and length of plastic area in the testing. The
experimental results are in good agreement with the analytical and
FE analyses. These results can be used as an introduction for impact
loading and energy absorbing of sandwich structures.
Abstract: Biological, psychological and social experiences and
perceptions of healthcare services in patients medically diagnosed of
coronary heart disease were investigated using a sample of 10
participants whose responses to the in-depth interview questions
were analyzed based on inter-and-intra-case analyses. The results
obtained revealed that advancing age, single status, divorce and/or
death of spouse and the issue of single parenting negatively impacted
patients- biopsychosocial experiences. The patients- experiences of
physical signs and symptoms, anxiety and depression, past serious
medical conditions, use of self-prescribed medications, family
history of poor mental/medical or physical health, nutritional
problems and insufficient physical activities heightened their risk of
coronary attack. Collectivist culture served as a big source of relieve
to the patients. Patients- temperament, experience of different
chronic life stresses/challenges, mood alteration, regular drinking,
smoking/gambling, and family/social impairments compounded their
health situation. Patients were satisfied with the biomedical services
rendered by the healthcare personnel, whereas their psychological
and social needs were not attended to. Effective procedural treatment
model, a holistic and multidimensional approach to the treatment of
heart disease patients was proposed.
Abstract: This research paper presents a framework on how to
build up malware dataset.Many researchers took longer time to
clean the dataset from any noise or to transform the dataset into a
format that can be used straight away for testing. Therefore, this
research is proposing a framework to help researchers to speed up
the malware dataset cleaningprocesses which later can be used for
testing. It is believed, an efficient malware dataset cleaning
processes, can improved the quality of the data, thus help to improve
the accuracy and the efficiency of the subsequent analysis. Apart
from that, an in-depth understanding of the malware taxonomy is
also important prior and during the dataset cleaning processes. A
new Trojan classification has been proposed to complement this
framework.This experiment has been conducted in a controlled lab
environment and using the dataset from VxHeavens dataset. This
framework is built based on the integration of static and dynamic
analyses, incident response method and knowledge database
discovery (KDD) processes.This framework can be used as the basis
guideline for malware researchers in building malware dataset.
Abstract: The turbulent mixing of coolant streams of different
temperature and density can cause severe temperature fluctuations in
piping systems in nuclear reactors. In certain periodic contraction
cycles these conditions lead to thermal fatigue. The resulting aging
effect prompts investigation in how the mixing of flows over a sharp
temperature/density interface evolves. To study the fundamental
turbulent mixing phenomena in the presence of density gradients,
isokinetic (shear-free) mixing experiments are performed in a square
channel with Reynolds numbers ranging from 2-500 to 60-000.
Sucrose is used to create the density difference. A Wire Mesh Sensor
(WMS) is used to determine the concentration map of the flow in the
cross section. The mean interface width as a function of velocity,
density difference and distance from the mixing point are analyzed
based on traditional methods chosen for the purposes of
atmospheric/oceanic stratification analyses. A definition of the
mixing layer thickness more appropriate to thermal fatigue and based
on mixedness is devised. This definition shows that the thermal
fatigue risk assessed using simple mixing layer growth can be
misleading and why an approach that separates the effects of large
scale (turbulent) and small scale (molecular) mixing is necessary.
Abstract: Environment today is featured with aging population,
increasing prevalence of chronic disease and complex of medical
treatment. Safe use of pharmaceutics relied very much on the efforts
made by both the health- related organizations and as well as the
government agencies. As far as the specialization concern in providing
health services to the patients, the government actively issued and
implemented the divisions of medical treatment and pharmaceutical to
improve the quality of care and to reduce medication errors and ensure
public health. Pharmaceutical sub-sector policy has been implemented
for 13 years. This study attempts to explore the factors that affect the
patients- behavior intention of refilling a prescription from a NHIB
pharmacy. Samples were those patients refilling their prescriptions
with the case NHIB pharmacies. A self-administered questionnaire
was used to collect respondents- information while the patients or
family members visit the pharmacy for the refilling. 1,200
questionnaires were dispatched in 37 pharmacies that randomly
selected from Pingtung City, Dongkang, Chaozhou, Hengchun areas.
732 responses were gained with 604 valid samples for further analyses.
Results of data analyses indicated that respondents- attitude,
subjective norm, perceived behavior control and behavior intentions
toward refilling behavior varied from some demographic variables to
another. This research also suggested adding actual behavior, either by
a self-report or observed, into the research.
Abstract: Natural frequencies and dynamic response of a spur
gear sector are investigated using a two dimensional finite element
model that offers significant advantages for dynamic gear analyses.
The gear teeth are analyzed for different operating speeds. A primary
feature of this modeling is determination of mesh forces using a
detailed contact analysis for each time step as the gears roll through
the mesh. ANSYS software has been used on the proposed model to
find the natural frequencies by Block Lanczos technique and
displacements and dynamic stresses by transient mode super position
method. The effect of rotational speed of the gear on the dynamic
response of gear tooth has been studied and design limits have been
discussed.
Abstract: Probabilistic characteristics of seismic responses of the
Partially Restrained connection rotation (PRCR) and panel zone
deformation (PZD) installed in older steel moment frames were
investigated in accordance with statistical inference in
decision-making process. The 4, 6 and 8 story older steel moment
frames with clip angle and T-stub connections were designed and
analyzed using 2%/50yrs ground motions in four cities of the
Mid-America earthquake region. The probability density function and
cumulative distribution function of PRCR and PZD were determined
by the goodness-of-fit tests based on probabilistic parameters
measured from the results of the nonlinear time-history analyses. The
obtained probabilistic parameters and distributions can be used to find
out what performance level mainly PR connections and panel zones
satisfy and how many PR connections and panel zones experience a
serious damage under the Mid-America ground motions.
Abstract: The purpose of this study was to investigate the
relationships among students- process of study, creative self-efficacy
and creativity while attending college. A total of 60 students enrolled
in Hsiuping Institute of Technology in central Taiwan were selected as
samples for the study. The instruments for this study included three
questionnaires to explore the aforesaid aspects.
This researchers tested creative self-efficacy and process of study,
and creativity with Pearson correlation and hierarchical regression
analyses. The major findings of this research are (1) the process of
study had direct positive predictability on creativity, and (2) the
relationship between process of study and creativity is partially
mediated by creative self-efficacy.
Abstract: Natural frequencies and dynamic response of a spur
gear sector are investigated using a two dimensional finite element
model that offers significant advantages for dynamic gear analyses.
The gear teeth are analyzed for different operating speeds. A primary
feature of this modeling is determination of mesh forces using a
detailed contact analysis for each time step as the gears roll through
the mesh. Transient mode super position method has been used to
find horizontal and vertical components of displacement and
dynamic stress. The finite element analysis software ANSYS has
been used on the proposed model to find the natural frequencies by
Block Lanczos technique and displacements and dynamic stresses by
transient mode super position method. A comparison of theoretical
(natural frequency and static stress) results with the finite element
analysis results has also been done. The effect of rotational speed of
the gears on the dynamic response of gear tooth has been studied and
design limits have been discussed.
Abstract: To understand the material characteristics of singleand
poly-crystals of pure copper, the respective relationships between
crystallographic orientations and microstructures, and the bending
and mechanical properties were examined. And texture distribution
is also analyzed. A bending test is performed in a SEM apparatus and
while its behaviors are observed in situ. Furthermore, some
analytical results related to crystal direction maps, inverse pole
figures, and textures were obtained from EBSD analyses.
Abstract: In this study, a fuzzy-logic based control system was
designed to ensure that time and energy is saved during the operation
of load elevators which are used during the construction of tall
buildings. In the control system that was devised, for the load
elevators to work more efficiently, the energy interval where the
motor worked was taken as the output variable whereas the amount
of load and the building height were taken as input variables. The
most appropriate working intervals depending on the characteristics
of these variables were defined by the help of an expert. Fuzzy expert
system software was formed using Delphi programming language. In
this design, mamdani max-min inference mechanism was used and
the centroid method was employed in the clarification procedure. In
conclusion, it is observed that the system that was designed is
feasible and this is supported by statistical analyses..
Abstract: The last years have seen an increasing use of image analysis techniques in the field of biomedical imaging, in particular in microscopic imaging. The basic step for most of the image analysis techniques relies on a background image free of objects of interest, whether they are cells or histological samples, to perform further analysis, such as segmentation or mosaicing. Commonly, this image consists of an empty field acquired in advance. However, many times achieving an empty field could not be feasible. Or else, this could be different from the background region of the sample really being studied, because of the interaction with the organic matter. At last, it could be expensive, for instance in case of live cell analyses. We propose a non parametric and general purpose approach where the background is built automatically stemming from a sequence of images containing even objects of interest. The amount of area, in each image, free of objects just affects the overall speed to obtain the background. Experiments with different kinds of microscopic images prove the effectiveness of our approach.
Abstract: The ability to distinguish missense nucleotide
substitutions that contribute to harmful effect from those that do not
is a difficult problem usually accomplished through functional in
vivo analyses. In this study, instead current biochemical methods, the
effects of missense mutations upon protein structure and function
were assayed by means of computational methods and information
from the databases. For this order, the effects of new missense
mutations in exon 5 of PTEN gene upon protein structure and
function were examined. The gene coding for PTEN was identified
and localized on chromosome region 10q23.3 as the tumor
suppressor gene. The utilization of these methods were shown that
c.319G>A and c.341T>G missense mutations that were recognized in
patients with breast cancer and Cowden disease, could be pathogenic.
This method could be use for analysis of missense mutation in others
genes.
Abstract: To improve the material characteristics of single- and
poly-crystals of pure copper, the respective relationships between crystallographic orientations and microstructures, and the bending and mechanical properties were examined. And texture distribution is also
analyzed. A grain refinement procedure was performed to obtain a
grained structure. Furthermore, some analytical results related to
crystal direction maps, inverse pole figures, and textures were obtained from SEM-EBSD analyses. Results showed that these
grained metallic materials have peculiar springback characteristics with various bending angles.
Abstract: The assessment of surface waters in Enugu metropolis
for fecal coliform bacteria was undertaken. Enugu urban was divided
into three areas (A1, A2 and A3), and fecal coliform bacteria
analysed in the surface waters found in these areas for four years
(2005-2008). The plate count method was used for the analyses. Data
generated were subjected to statistical tests involving; Normality test,
Homogeneity of variance test, correlation test, and tolerance limit
test. The influence of seasonality and pollution trends were
investigated using time series plots. Results from the tolerance limit
test at 95% coverage with 95% confidence, and with respect to EU
maximum permissible concentration show that the three areas suffer
from fecal coliform pollution. To this end, remediation procedure
involving the use of saw-dust extracts from three woods namely;
Chlorophora-Excelsa (C-Excelsa),Khayan-Senegalensis,(CSenegalensis)
and Erythrophylum-Ivorensis (E-Ivorensis) in
controlling the coliforms was studied. Results show that mixture of
the acetone extracts of the woods show the most effective
antibacterial inhibitory activities (26.00mm zone of inhibition)
against E-coli. Methanol extract mixture of the three woods gave best
inhibitory activity (26.00mm zone of inhibition) against S-areus, and
25.00mm zones of inhibition against E-Aerogenes. The aqueous
extracts mixture gave acceptable zones of inhibitions against the
three bacteria organisms.