Abstract: This paper aims to perform the second law analysis of
thermodynamics on the laminar film condensation of pure saturated
vapor flowing in the direction of gravity on an ellipsoid with variable
wall temperature. The analysis provides us understanding how the
geometric parameter- ellipticity and non-isothermal wall temperature
variation amplitude “A." affect entropy generation during film-wise
condensation heat transfer process. To understand of which
irreversibility involved in this condensation process, we derived an
expression for the entropy generation number in terms of ellipticity
and A. The result indicates that entropy generation increases with
ellipticity. Furthermore, the irreversibility due to finite temperature
difference heat transfer dominates over that due to condensate film
flow friction and the local entropy generation rate decreases with
increasing A in the upper half of ellipsoid. Meanwhile, the local
entropy generation rate enhances with A around the rear lower half of
ellipsoid.
Abstract: A general purpose viscous flow solver Ansys CFX
was used to solve the unsteady three-dimensional (3D) Reynolds
Averaged Navier-Stokes Equation (RANSE) for simulating a 3D
numerical viscous wave tank. A flap-type wave generator was
incorporated in the computational domain to generate the desired
incident waves. Authors have made effort to study the physical
behaviors of Flap type wave maker with governing parameters.
Dependency of the water fill depth, Time period of oscillations and
amplitude of oscillations of flap were studied. Effort has been made
to establish relations between parameters. A validation study was
also carried out against CFD methodology with wave maker theory.
It has been observed that CFD results are in good agreement with
theoretical results. Beaches of different slopes were introduced to
damp the wave, so that it should not cause any reflection from
boundary. As a conclusion this methodology can simulate the
experimental wave-maker for regular wave generation for different
wave length and amplitudes.
Abstract: The tree structured approach of non-uniform filterbank
(NUFB) is normally used in perfect reconstruction (PR). The PR is
not always feasible due to certain limitations, i.e, constraints in
selecting design parameters, design complexity and some times
output is severely affected by aliasing error if necessary and
sufficient conditions of PR is not satisfied perfectly. Therefore, there
has been generalized interest of researchers to go for near perfect
reconstruction (NPR). In this proposed work, an optimized tree
structure technique is used for the design of NPR non-uniform
filterbank. Window functions of Blackman family are used to design
the prototype FIR filter. A single variable linear optimization is used
to minimize the amplitude distortion. The main feature of the
proposed design is its simplicity with linear phase property.
Abstract: The paper compares different channel models used for
modeling Broadband Power-Line Communication (BPLC) system.
The models compared are Zimmermann and Dostert, Philipps,
Anatory et al and Anatory et al generalized Transmission Line (TL)
model. The validity of each model was compared in time domain
with ATP-EMTP software which uses transmission line approach. It
is found that for a power-line network with minimum number of
branches all the models give similar signal/pulse time responses
compared with ATP-EMTP software; however, Zimmermann and
Dostert model indicates the same amplitude but different time delay.
It is observed that when the numbers of branches are increased only
generalized TL theory approach results are comparable with ATPEMTP
results. Also the Multi-Carrier Spread Spectrum (MC-SS)
system was applied to check the implication of such behavior on the
modulation schemes. It is observed that using Philipps on the
underground cable can predict the performance up to 25dB better
than other channel models which can misread the actual performance
of the system. Also modified Zimmermann and Dostert under
multipath can predict a better performance of about 5dB better than
the actual predicted by Generalized TL theory. It is therefore
suggested for a realistic BPLC system design and analyses the model
based on generalized TL theory be used.
Abstract: The principle of frequency and amplitude measurement of a vibrating object in water using ultrasonic speckle technique is presented in this paper. Compared with other traditional techniques, the ultrasonic speckle technique can be applied to vibration measurement of a nonmetal object with rough surface in water in a noncontact way. The relationship between speckle movement and object movement was analyzed. Based on this study, an ultrasonic speckle measurement system was set up. With this system the frequency and amplitude of an underwater vibrating cantilever beam was detected. The result shows that the experimental data is in good agreement with the calibrating data.
Abstract: In order to improve control performance and eliminate steady, a coupling compensation for 6-DOF parallel robot is presented. Taking dynamic load Tank Simulator as the research object, this paper analyzes the coupling of 6-DOC parallel robot considering the degree of freedom of the 6-DOF parallel manipulator. The coupling angle and coupling velocity are derived based on inverse kinematics model. It uses the mechanism-model combined method which takes practical moving track that considering the performance of motion controller and motor as its input to make the study. Experimental results show that the coupling compensation improves motion stability as well as accuracy. Besides, it decreases the dither amplitude of dynamic load Tank Simulator.
Abstract: Power-line networks are widely used today for broadband data transmission. However, due to multipaths within the broadband power line communication (BPLC) systems owing to stochastic changes in the network load impedances, branches, etc., network or channel capacity performances are affected. This paper attempts to investigate the performance of typical medium voltage channels that uses Orthogonal Frequency Division Multiplexing (OFDM) techniques with Quadrature Amplitude Modulation (QAM) sub carriers. It has been observed that when the load impedances are different from line characteristic impedance channel performance decreases. Also as the number of branches in the link between the transmitter and receiver increases a loss of 4dB/branch is found in the signal to noise ratio (SNR). The information presented in the paper could be useful for an appropriate design of the BPLC systems.
Abstract: This paper presents results obtained from the
numerical solution for the flow past an oscillating circular cylinder at
Reynolds number of 200. The frequency of oscillation was fixed to
the vortex shedding frequency from a fixed cylinder, f0, while the
amplitudes of oscillations were varied from to 1.1a, where a
represents the radius of the cylinder. The response of the flow
through the fluid forces acting on the surface of the cylinder are
investigated. The lock-on phenomenon is captured at low oscillation
amplitudes.
Abstract: ECG analysis method was developed using ROC
analysis of PVC detecting algorithm. ECG signal of MIT-BIH
arrhythmia database was analyzed by MATLAB. First of all, the
baseline was removed by median filter to preprocess the ECG signal.
R peaks were detected for ECG analysis method, and normal VCG
was extracted for VCG analysis method. Four PVC detecting
algorithm was analyzed by ROC curve, which parameters are
maximum amplitude of QRS complex, width of QRS complex, r-r
interval and geometric mean of VCG. To set cut-off value of
parameters, ROC curve was estimated by true-positive rate
(sensitivity) and false-positive rate. sensitivity and false negative rate
(specificity) of ROC curve calculated, and ECG was analyzed using
cut-off value which was estimated from ROC curve. As a result, PVC
detecting algorithm of VCG geometric mean have high availability,
and PVC could be detected more accurately with amplitude and width
of QRS complex.
Abstract: The paper deals with the estimation of amplitude and phase of an analogue multi-harmonic band-limited signal from irregularly spaced sampling values. To this end, assuming the signal fundamental frequency is known in advance (i.e., estimated at an independent stage), a complexity-reduced algorithm for signal reconstruction in time domain is proposed. The reduction in complexity is achieved owing to completely new analytical and summarized expressions that enable a quick estimation at a low numerical error. The proposed algorithm for the calculation of the unknown parameters requires O((2M+1)2) flops, while the straightforward solution of the obtained equations takes O((2M+1)3) flops (M is the number of the harmonic components). It is applied in signal reconstruction, spectral estimation, system identification, as well as in other important signal processing problems. The proposed method of processing can be used for precise RMS measurements (for power and energy) of a periodic signal based on the presented signal reconstruction. The paper investigates the errors related to the signal parameter estimation, and there is a computer simulation that demonstrates the accuracy of these algorithms.
Abstract: In this study, rotating flexible shaft-disk system
having flexible beams is considered as a dynamic system. After
neglecting nonlinear terms, torsional vibration of the shaft-disk
system and lateral and longitudinal vibration of the flexible beam are
still coupled through the motor speed. The system has three natural
frequencies; the flexible shaft-disk system torsional natural
frequency, the flexible beam lateral and longitudinal natural
frequencies. Eigenvalue calculations show that while the shaft speed
changes, torsional natural frequency of the shaft-disk system and the
beam longitudinal natural frequency are not changing but the beam
lateral natural frequency changes. Beam lateral natural frequency
stays the same as the nonrotating beam lateral natural frequency ωb
until the motor speed ωm is equal to ωb. After then ωb increases and
remains equal to the motor speed ωm until the motor speed is equal to
the shaft-disk system natural frequency ωT. Then the beam lateral
natural frequency ωb becomes equal to the natural frequency ωT and
stays same while the motor speed ωm is increased. Modal amplitudes
and phase angles of the vibrations are also plotted against the motor
speed ωm.
Abstract: In this paper, a new approach for target recognition based on the Empirical mode decomposition (EMD) algorithm of Huang etal. [11] and the energy tracking operator of Teager [13]-[14] is introduced. The conjunction of these two methods is called Teager-Huang analysis. This approach is well suited for nonstationary signals analysis. The impulse response (IR) of target is first band pass filtered into subsignals (components) called Intrinsic mode functions (IMFs) with well defined Instantaneous frequency (IF) and Instantaneous amplitude (IA). Each IMF is a zero-mean AM-FM component. In second step, the energy of each IMF is tracked using the Teager energy operator (TEO). IF and IA, useful to describe the time-varying characteristics of the signal, are estimated using the Energy separation algorithm (ESA) algorithm of Maragos et al .[16]-[17]. In third step, a set of features such as skewness and kurtosis are extracted from the IF, IA and IMF energy functions. The Teager-Huang analysis is tested on set of synthetic IRs of Sonar targets with different physical characteristics (density, velocity, shape,? ). PCA is first applied to features to discriminate between manufactured and natural targets. The manufactured patterns are classified into spheres and cylinders. One hundred percent of correct recognition is achieved with twenty three echoes where sixteen IRs, used for training, are free noise and seven IRs, used for testing phase, are corrupted with white Gaussian noise.
Abstract: The aim of the work was to attenuate the vibration amplitude in CESNA 172 airplane wing by using Functionally Graded Material instead of uniform or composite material. Wing strength was achieved by means of stress analysis study, while wing vibration amplitudes and shapes were achieved by means of Modal and Harmonic analysis. Results were verified by applying the methodology in a simple cantilever plate to the simple model and the results were promising and the same methodology can be applied to the airplane wing model. Aluminum models, Titanium models, and functionally graded materials of Aluminum and titanium results were compared to show a great vibration attenuation after using the FGM. Optimization in FGM gradation satisfied our objective of reducing and attenuating the vibration amplitudes to show the effect of using FGM in vibration behavior. Testing the Aluminum rich models, and comparing it with the titanium rich model was an optimization in this paper. Results have shown a significant attenuation in vibration magnitudes when using FGM instead of Titanium Plate, and Aluminium wing with FGM Spurs instead of Aluminium wings. It was also recommended that in future, changing the graphical scale to 1:10 or even 1:1 when the computers- capabilities allow.
Abstract: Transition prediction of boundary layers has always
been an important problem in fluid mechanics both theoretically and
practically, yet notwithstanding the great effort made by many
investigators, there is no satisfactory answer to this problem. The most
popular method available is so-called e-N method which is heavily
dependent on experiments and experience. The author has proposed
improvements to the e-N method, so to reduce its dependence on
experiments and experience to a certain extent. One of the key
assumptions is that transition would occur whenever the velocity
amplitude of disturbance reaches 1-2% of the free stream velocity.
However, the reliability of this assumption needs to be verified. In this
paper, transition prediction on a flat plate is investigated by using both
the improved e-N method and the parabolized stability equations (PSE)
methods. The results show that the transition locations predicted by
both methods agree reasonably well with each other, under the above
assumption. For the supersonic case, the critical velocity amplitude in
the improved e-N method should be taken as 0.013, whereas in the
subsonic case, it should be 0.018, both are within the range 1-2%.
Abstract: BER analysis of Impulse Radio Ultra Wideband (IRUWB) pulse modulations over S-V channel model is proposed in this paper. The UWB pulse is Gaussian monocycle pulse modulated using Pulse Amplitude Modulation (PAM) and Pulse Position Modulation (PPM). The channel model is generated from a modified S-V model. Bit-error rate (BER) is measured over several of bit rates. The result shows that all modulation are appropriate for both LOS and NLOS channel, but PAM gives better performance in bit rates and SNR. Moreover, as standard of speed has been given for UWB, the communication is appropriate with high bit rates in LOS channel.
Abstract: Performance control law is studied for an
interconnected fractional nonlinear system. Applying a backstepping
algorithm, a backstepping sliding mode controller (BSMC) is
developed for fractional nonlinear system. To improve control law
performance, BSMC is coupled to an adaptive sliding mode observer
have a filtered error as a sliding surface. The both architecture
performance is studied throughout the inverted pendulum mounted on
a cart. Simulation result show that the BSMC coupled to an adaptive
sliding mode observer have stable control law and eligible control
amplitude than the BSMC.
Abstract: This study introduces a new method for detecting,
sorting, and localizing spikes from multiunit EEG recordings. The
method combines the wavelet transform, which localizes distinctive
spike features, with Super-Paramagnetic Clustering (SPC) algorithm,
which allows automatic classification of the data without assumptions
such as low variance or Gaussian distributions. Moreover, the method
is capable of setting amplitude thresholds for spike detection. The
method makes use of several real EEG data sets, and accordingly the
spikes are detected, clustered and their times were detected.
Abstract: This paper describes a study of geometrically
nonlinear free vibration of thin circular functionally graded (CFGP)
plates resting on Winkler elastic foundations. The material properties
of the functionally graded composites examined here are assumed to
be graded smoothly and continuously through the direction of the
plate thickness according to a power law and are estimated using the
rule of mixture. The theoretical model is based on the classical Plate
theory and the Von-Kármán geometrical nonlinearity assumptions.
An homogenization procedure (HP) is developed to reduce the
problem considered here to that of isotropic homogeneous circular
plates resting on Winkler foundation. Hamilton-s principle is applied
and a multimode approach is derived to calculate the fundamental
nonlinear frequency parameters which are found to be in a good
agreement with the published results. On the other hand, the
influence of the foundation parameters on the nonlinear fundamental
frequency has also been analysed.
Abstract: SEMG (Surface Electromyogram) is one of the
bio-signals and is generated from the muscle. And there are many
research results that use forearm EMG to detect hand motions. In this
paper, we will talk about our developed the robot hand system that can
control grasping power by SEMG. In our system, we suppose that
muscle power is proportional to the amplitude of SEMG. The power is
estimated and the grip power of a robot hand is able to be controlled
using estimated muscle power in our system. In addition, to perform a
more precise control can be considered to build a closed loop feedback
system as an object to a subject to pressure from the edge of hand. Our
objectives of this study are the development of a method that makes
perfect detection of the hand grip force possible using SEMG patterns,
and applying this method to the man-machine interface.
Abstract: An analytical solution for dispersion of a solute in the
peristaltic motion of a couple stress fluid in the presence of magnetic
field with both homogeneous and heterogeneous chemical reactions is
presented. The average effective dispersion coefficient has been found
using Taylor-s limiting condition and long wavelength approximation.
The effects of various relevant parameters on the average effective
coefficient of dispersion have been studied. The average effective
dispersion coefficient tends to decrease with magnetic field parameter,
homogeneous chemical reaction rate parameter and amplitude ratio
but tends to increase with heterogeneous chemical reaction rate
parameter.