Abstract: The National Blood Center, Thai Red Cross Society is
responsible for providing blood to hospitals all over the country.
When any hospital needs blood, it will have to send the vehicle to
pick up at the NBC. There are a lot of vehicles to pick up blood at the
NBC every day. Each vehicle is usually empty for inbound trip and a
little loaded for outbound. The NBC realized such waste or loss and
there have been the third party offered to distribute blood and charge
for fee. This paper proposes to apply the vehicle routing problem
(VRP) for estimating the fair price. The idea is tested with the real
data during seven-day period of 6 – 12 July 2010 to estimate the fair
price for transporting blood in Bangkok Metropolitan Region.
Abstract: This paper describes the design considerations of an
experimental setup for research and exploring the drives of batteryfed
electric vehicles. Effective setup composition and its components
are discussed. With experimental setup described in this paper,
durability and functional tests can be procured to the customers.
Multiple experiments are performed in the form of steady-state
system exploring, acceleration programs, multi-step tests (speed
control, torque control), load collectives or close-to-reality driving
tests (driving simulation). Main focus of the functional testing is on
the measurements of power and energy efficiency and investigations
in driving simulation mode, which are used for application purposes.
In order to enable the examination of the drive trains beyond
standard modes of operation, different other parameters can be
studied also.
Abstract: An experimental and simulation flight test has been carried out to evaluate the longitudinal gliding characteristics of a lifting body with blunted half-cone geometry. The novelty here is the lifting body's pitch control mechanism, which consists of a pair of leading-edge rotating cylinders. Flight simulation uses aerodynamic data from computational fluid dynamics supported by wind-tunnel test. Flight test consists of releasing an aluminum lifting body model from a moving vehicle at the appropriate wind speed while measuring the lifting body's variation of altitude against time of flight. Results show that leading-edge rotating cylinder is able to give small amounts of improvement to the longitudinal stability and pitch control to the lifting body.
Abstract: The measurement of aerodynamic forces and moments
acting on an aircraft model is important for the development of wind
tunnel measurement technology to predict the performance of the full
scale vehicle. The potentials of an aircraft model with and without
winglet and aerodynamic characteristics with NACA wing No. 65-3-
218 have been studied using subsonic wind tunnel of 1 m × 1 m
rectangular test section and 2.5 m long of Aerodynamics Laboratory
Faculty of Engineering (University Putra Malaysia). Focusing on
analyzing the aerodynamic characteristics of the aircraft model, two
main issues are studied in this paper. First, a six component wind
tunnel external balance is used for measuring lift, drag and pitching
moment. Secondly, Tests are conducted on the aircraft model with
and without winglet of two configurations at Reynolds numbers
1.7×105, 2.1×105, and 2.5×105 for different angle of attacks. Fuzzy
logic approach is found as efficient for the representation,
manipulation and utilization of aerodynamic characteristics.
Therefore, the primary purpose of this work was to investigate the
relationship between lift and drag coefficients, with free-stream
velocities and angle of attacks, and to illustrate how fuzzy logic
might play an important role in study of lift aerodynamic
characteristics of an aircraft model with the addition of certain
winglet configurations. Results of the developed fuzzy logic were
compared with the experimental results. For lift coefficient analysis,
the mean of actual and predicted values were 0.62 and 0.60
respectively. The coreelation between actual and predicted values
(from FLS model) of lift coefficient in different angle of attack was
found as 0.99. The mean relative error of actual and predicted valus
was found as 5.18% for the velocity of 26.36 m/s which was found to
be less than the acceptable limits (10%). The goodness of fit of
prediction value was 0.95 which was close to 1.0.
Abstract: The fuel cost of the motor vehicle operating on its
common route is an important part of the operating cost. Therefore,
the importance of the fuel saving is increasing day by day. One of the
parameters which improve fuel saving is the regulation of driving
characteristics. The number and duration of stop is increased by the
heavy traffic load. It is possible to improve the fuel saving with
regulation of traffic flow and driving characteristics. The researches
show that the regulation of the traffic flow decreases fuel
consumption, but it is not enough to improve fuel saving without the
regulation of driving characteristics. This study analyses the fuel
consumption of two trips of city bus operating on its common route
and determines the effect of traffic density and driving characteristics
on fuel consumption. Finally it offers some suggestions about
regulation of driving characteristics to improve the fuel saving. Fuel
saving is determined according to the results obtained from
simulation program. When experimental and simulation results are
compared, it has been found that the fuel saving was reached up the
to 40 percent ratios.
Abstract: This paper presents an optimization of the hull
separation, i.e. transverse clearance. The main objective is to identify
the feasible speed ranges and find the optimum transverse clearance
considering the minimum wave-making resistance. The dimensions
and the weight of hardware systems installed in the catamaran
structured fuel cell powered USV (Unmanned Surface Vehicle) were
considered as constraints. As the CAE (Computer Aided Engineering)
platform FRIENDSHIP-Framework was used. The hull surface
modeling, DoE (Design of Experiment), Tangent search optimization,
tool integration and the process automation were performed by
FRIENDSHIP-Framework. The hydrodynamic result was evaluated
by XPAN the potential solver of SHIPFLOW.
Abstract: A long-term campaign for monitoring the
concentration of atmospheric Particulate Matter (PM) was conducted
at multiple sites located in the center and suburbs of the Tokyo
Metropolitan Area in Japan. The concentration of fine PM has shown a
declining trend over the last two decades. A positive matrix
factorization model elucidated that the contribution of combustion
sources was drastically reduced. In Japan, the regulations on vehicle
exhaust emissions were phased in and gradually tightened over the last
two decades, which has triggered a notable reduction in PM emissions
from automobiles and has contributed to the mitigation of the problem
of fine PM pollution.
Abstract: A robust wheel slip controller for electric vehicles is
introduced. The proposed wheel slip controller exploits the dynamics
of electric traction drives and conventional hydraulic brakes for
achieving maximum energy efficiency and driving safety. Due to
the control of single wheel traction motors in combination with a
hydraulic braking system, it can be shown, that energy recuperation
and vehicle stability control can be realized simultaneously. The
derivation of a sliding mode wheel slip controller accessing two
drivetrain actuators is outlined and a comparison to a conventionally
braked vehicle is shown by means of simulation.
Abstract: In a travelling wave thermoacoustic device, the
regenerator sandwiched between a pair of (hot and cold) heat
exchangers constitutes the so-called thermoacoustic core, where the
thermoacoustic energy conversion from heat to acoustic power takes
place. The temperature gradient along the regenerator caused by the
two heat exchangers excites and maintains the acoustic wave in the
resonator. The devices are called travelling wave thermoacoustic
systems because the phase angle difference between the pressure and
velocity oscillation is close to zero in the regenerator. This paper
presents the construction and testing of a thermoacoustic engine
equipped with a ceramic regenerator, made from a ceramic material
that is usually used as catalyst substrate in vehicles- exhaust systems,
with fine square channels (900 cells per square inch). The testing
includes the onset temperature difference (minimum temperature
difference required to start the acoustic oscillation in an engine), the
acoustic power output, thermal efficiency and the temperature profile
along the regenerator.
Abstract: The adaptive power control of Code Division Multiple
Access (CDMA) communications using Remote Radio Head
(RRH) between multiple Unmanned Aerial Vehicles (UAVs) with
a link-budget based Signal-to-Interference Ratio (SIR) estimate is
applied to four inner loop power control algorithms. It is concluded
that Base Station (BS) can calculate not only UAV distance using
linearity between speed and Consecutive Transmit-Power-Control
Ratio (CTR) of Adaptive Step-size Closed Loop Power Control (ASCLPC),
Consecutive TPC Ratio Step-size Closed Loop Power Control
(CS-CLPC), Fixed Step-size Power Control (FSPC), but also UAV
position with Received Signal Strength Indicator (RSSI) ratio of
RRHs.
Abstract: This document describes an electronic speed control designed to drive two DC motors from a 6 V battery pack to be controlled by a commercial universal infrared remote control hand set. Conceived for a tank-like vehicle, one motor drives the left side wheels or tracks and the other motor drives the right side. As it is shown here, there is a left-right steering input and a forward– backward throttles input, like would be used on a model car. It is designed using a microcontroller PIC16F873A.
Abstract: An adaptive neural network controller for
autonomous underwater vehicles (AUVs) is presented in this paper.
The AUV model is highly nonlinear because of many factors, such as
hydrodynamic drag, damping, and lift forces, Coriolis and centripetal
forces, gravity and buoyancy forces, as well as forces from thruster.
In this regards, a nonlinear neural network is used to approximate the
nonlinear uncertainties of AUV dynamics, thus overcoming some
limitations of conventional controllers and ensure good performance.
The uniform ultimate boundedness of AUV tracking errors and the
stability of the proposed control system are guaranteed based on
Lyapunov theory. Numerical simulation studies for motion control of
an AUV are performed to demonstrate the effectiveness of the
proposed controller.
Abstract: Dual bell nozzle is a promising one among the altitude
adaptation nozzle concepts, which offer increased nozzle
performance in rocket engines. Its advantage is the simplicity it offers
due to the absence of any additional mechanical device or movable
parts. Hence it offers reliability along with improved nozzle
performance as demanded by future launch vehicles. Among other
issues, the flow transition to the extension nozzle of a dual bell
nozzle is one of the major issues being studied in the development of
dual bell nozzle. A parameter named over-expansion factor, which
controls the value of the wall inflection angle, has been reported to
have substantial influence in this transition process. This paper
studies, through CFD and cold flow experiments, the effect of overexpansion
factor on flow transition in dual bell nozzles.
Abstract: Electronic nose (array of chemical sensors) are widely
used in food industry and pollution control. Also it could be used to
locate or detect the direction of the source of emission odors. Usually
this task is performed by electronic nose (ENose) cooperated with
mobile vehicles, but when a source is instantaneous or surrounding is
hard for vehicles to reach, problem occurs. Thus a method for
stationary ENose to detect the direction of the source and locate the
source will be required. A novel method which uses the ratio between
the responses of different sensors as a discriminant to determine the
direction of source in natural wind surroundings is presented in this
paper. The result shows that the method is accurate and easily to be
implemented. This method could be also used in movably, as an
optimized algorithm for robot tracking source location.
Abstract: This paper presents the application of Intelligent
Techniques to the various duties of Intelligent Condition Monitoring
Systems (ICMS) for Unmanned Aerial Vehicle (UAV) Robots. These
Systems are intended to support these Intelligent Robots in the event
of a Fault occurrence. Neural Networks are used for Diagnosis, whilst
Fuzzy Logic is intended for Prognosis and Remedy. The ultimate
goals of ICMS are to save large losses in financial cost, time and
data.
Abstract: A semi-active control strategy for suspension
systems of passenger cars is presented employing
Magnetorheological (MR) dampers. The vehicle is modeled with
seven DOFs including the, roll pitch and bounce of car body, and
the vertical motion of the four tires. In order to design an optimal
controller based on the actuator constraints, a Linear-Quadratic
Regulator (LQR) is designed. The design procedure of the LQR
consists of selecting two weighting matrices to minimize the energy
of the control system. This paper presents a hybrid optimization
procedure which is a combination of gradient-based and
evolutionary algorithms to choose the weighting matrices with
regards to the actuator constraint. The optimization algorithm is
defined based on maximum comfort and actuator constraints. It is
noted that utilizing the present control algorithm may significantly
reduce the vibration response of the passenger car, thus, providing
a comfortable ride.
Abstract: The liquid cargo contained in a partly-filled road tank
vehicle is prone to dynamic slosh movement when subjected to
external disturbances. The slosh behavior has been identified as a
significant factor impairing the safety of liquid cargo transportation.
The laboratory experiments have been conducted for analyzing fluid
slosh in partly filled tanks. The experiment results measured under
forced harmonic excitations reveal the three-dimensional nature of
the fluid motion and coupling between the lateral and longitudinal
fluid slosh at resonance. Several spectral components are observed
for the transient slosh forces, which can be associated with the
excitation, resonance, and beat frequencies. The peak slosh forces
and moments in the vicinity of resonance are significantly larger than
those of the equivalent rigid mass. Due to the nature of coupling
between sloshing fluid and vehicle body, the issue of the dynamic
fluid-structure interaction is essential in the analysis of tank-vehicle
dynamics. A dynamic pitch plane model of a Tridem truck
incorporated the fluid slosh dynamics is developed to analyze the
fluid-vehicle interaction under the straight-line braking maneuvers.
The results show that the vehicle responses are highly associated
with the characteristics of fluid slosh force and moment.
Abstract: A subjectively influenced router for vehicles in a fourjunction
traffic system is presented. The router is based on a 3-layer
Backpropagation Neural Network (BPNN) and a greedy routing
procedure. The BPNN detects priorities of vehicles based on the
subjective criteria. The subjective criteria and the routing procedure
depend on the routing plan towards vehicles depending on the user.
The routing procedure selects vehicles from their junctions based on
their priorities and route them concurrently to the traffic system. That
is, when the router is provided with a desired vehicles selection
criteria and routing procedure, it routes vehicles with a reasonable
junction clearing time. The cost evaluation of the router determines
its efficiency. In the case of a routing conflict, the router will route
the vehicles in a consecutive order and quarantine faulty vehicles.
The simulations presented indicate that the presented approach is an
effective strategy of structuring a subjective vehicle router.
Abstract: This paper proposes a vehicle-to-vehicle propagation
model implemented with SDL. To estimate the channel
characteristics for Inter-Vehicle communication, we first define a
predicted propagation pathloss between the moving vehicles under
three typical scenarios. A Ray-tracing method is used for the simple
gamma model performance.
Abstract: This paper reports a case study on how a conceptual
and analytical thinking approach was used in Art and Design Department at Multimedia University (Malaysia) in addressing the
issues of one nation and its impact in the society through artworks. The art project was designed for students to increase the know-how
and develop creative thinking in design and communication. Goals of the design project were: (1) to develop creative thinking in design
and communication, (2) to increase student understanding on the
process of problem solving for design work, and (3) to use design
elements and principles to generate interest, attention and emotional responses. An exhibition entitled "One Nation" was showcased to
local and international viewers consisting of the general public, professionals, academics, artists and students. Findings indicate that the project supported several visual art standards, as well as
generated awareness in the society. This project may be of interest to
current and future art educators and others interested in the potential
of utilizing global issues as content for art, community and environment studies for the purpose of educational art.