Abstract: The information of the impact cutting behavior of plants stalk plays an important role in the design and fabrication of plants cutting equipment. It is difficult to investigate a theoretical method for defining cutting properties of plants stalks because the cutting process is complex. Thus, it is necessary to set up an experimental approach to determine cutting parameters for a single stalk. To measure the shear force, shear energy and shear strength of plant stalk, a special impact cutting tester was fabricated. It was similar to an Izod impact cutting tester for metals but a cutting blade and data acquisition system were attached to the end of pendulum's arm. The apparatus was included four strain gages and a digital indicator to show the real-time cutting force of plant stalk. To measure the shear force and also testing the apparatus, two plants’ stalks, like buxus and privet, were selected. The samples (buxus and privet stalks) were cut under impact cutting process at four loading rates 1, 2, 3 and 4 m.s-1 and three internodes fifth, tenth and fifteenth by the apparatus. At buxus cutting analysis: the minimum value of cutting energy was obtained at fifth internode and loading rate 4 m.s-1 and the maximum value of shear energy was obtained at fifteenth internode and loading rate 1 m.s-1. At privet cutting analysis: the minimum value of shear consumption energy was obtained at fifth internode and loading rate: 4 m.s-1 and the maximum value of shear energy was obtained at fifteenth internode and loading rate: 1 m.s-1. The statistical analysis at both plants showed that the increase of impact cutting speed would decrease the shear consumption energy and shear strength. In two scenarios, the results showed that with increase the cutting speed, shear force would decrease.
Abstract: Delays in the construction industry are a global phenomenon. Many construction projects experience extensive delays exceeding the initially estimated completion time. The main purpose of this study is to identify construction projects typical behaviors in order to develop a prognosis and management tool. Being able to know a construction projects schedule tendency will enable evidence-based decision-making to allow resolutions to be made before delays occur. This study presents an innovative approach that uses Cluster Analysis Method to support predictions during Earned Value Analyses. A clustering analysis was used to predict future scheduling, Earned Value Management (EVM), and Earned Schedule (ES) principal Indexes behaviors in construction projects. The analysis was made using a database with 90 different construction projects. It was validated with additional data extracted from literature and with another 15 contrasting projects. For all projects, planned and executed schedules were collected and the EVM and ES principal indexes were calculated. A complete linkage classification method was used. In this way, the cluster analysis made considers that the distance (or similarity) between two clusters must be measured by its most disparate elements, i.e. that the distance is given by the maximum span among its components. Finally, through the use of EVM and ES Indexes and Tukey and Fisher Pairwise Comparisons, the statistical dissimilarity was verified and four clusters were obtained. It can be said that construction projects show an average delay of 35% of its planned completion time. Furthermore, four typical behaviors were found and for each of the obtained clusters, the interim milestones and the necessary rhythms of construction were identified. In general, detected typical behaviors are: (1) Projects that perform a 5% of work advance in the first two tenths and maintain a constant rhythm until completion (greater than 10% for each remaining tenth), being able to finish on the initially estimated time. (2) Projects that start with an adequate construction rate but suffer minor delays culminating with a total delay of almost 27% of the planned time. (3) Projects which start with a performance below the planned rate and end up with an average delay of 64%, and (4) projects that begin with a poor performance, suffer great delays and end up with an average delay of a 120% of the planned completion time. The obtained clusters compose a tool to identify the behavior of new construction projects by comparing their current work performance to the validated database, thus allowing the correction of initial estimations towards more accurate completion schedules.
Abstract: ABET accredited programs must assess the development of student learning outcomes (SOs) in engineering programs. Different institutions implement different strategies for this assessment, and they are usually designed “in house.” This paper presents a proposal for including standardized tests to complement the ABET assessment model in an engineering college made up of six distinct engineering programs. The engineering college formulated a model of quality assurance in education to be implemented throughout the six engineering programs to regularly assess and evaluate the achievement of SOs in each program offered. The model uses diverse techniques and sources of data to assess student performance and to implement actions of improvement based on the results of this assessment. The model is called “Assessment Process Model” and it includes SOs A through K, as defined by ABET. SOs can be divided into two categories: “hard skills” and “professional skills” (soft skills). The first includes abilities, such as: applying knowledge of mathematics, science, and engineering and designing and conducting experiments, as well as analyzing and interpreting data. The second category, “professional skills”, includes communicating effectively, and understanding professional and ethnical responsibility. Within the Assessment Process Model, various tools were used to assess SOs, related to both “hard” as well as “soft” skills. The assessment tools designed included: rubrics, surveys, questionnaires, and portfolios. In addition to these instruments, the Engineering College decided to use tools that systematically gather consistent quantitative data. For this reason, an in-house exam was designed and implemented, based on the curriculum of each program. Even though this exam was administered during various academic periods, it is not currently considered standardized. In 2017, the Engineering College included three standardized tests: one to assess mathematical and scientific reasoning and two more to assess reading and writing abilities. With these exams, the college hopes to obtain complementary information that can help better measure the development of both hard and soft skills of students in the different engineering programs. In the first semester of 2017, the three exams were given to three sample groups of students from the six different engineering programs. Students in the sample groups were either from the first, fifth, and tenth semester cohorts. At the time of submission of this paper, the engineering college has descriptive statistical data and is working with various statisticians to have a more in-depth and detailed analysis of the sample group of students’ achievement on the three exams. The overall objective of including standardized exams in the assessment model is to identify more precisely the least developed SOs in order to define and implement educational strategies necessary for students to achieve them in each engineering program.
Abstract: This study presented the seismic fragility framework of concrete weir structure subjected to strong seismic ground motions and in particular, concrete aging condition of the weir structure was taken into account in this study. In order to understand the influence of concrete aging on the weir structure, by using probabilistic risk assessment, the analytical seismic fragility of the weir structure was derived for pre- and post-deterioration of concrete. The performance of concrete weir structure after five years was assumed for the concrete aging or deterioration, and according to after five years’ condition, the elastic modulus was simply reduced about one–tenth compared with initial condition of weir structures. A 2D nonlinear finite element analysis was performed considering the deterioration of concrete in weir structures using ABAQUS platform, a commercial structural analysis program. Simplified concrete degradation was resulted in the increase of almost 45% of the probability of failure at Limit State 3, in comparison to initial construction stage, by analyzing the seismic fragility.
Abstract: Bringing forth a survey on recent higher order spline
techniques for solving boundary value problems in ordinary
differential equations. Here we have discussed the summary of the
articles since 2000 till date based on higher order splines like Septic,
Octic, Nonic, Tenth, Eleventh, Twelfth and Thirteenth Degree
splines. Comparisons of methods with own critical comments as
remarks have been included.
Abstract: Although several factors that affect learning to
program have been identified over the years, there continues to be no
indication of any consensus in understanding why some students learn
to program easily and quickly while others have difficulty. Seldom
have researchers considered the problem of how to help the students
enhance the programming learning outcome. The research had been
conducted at a high school in Taiwan. Students participating in the
study consist of 330 tenth grade students enrolled in the Basic
Computer Concepts course with the same instructor. Two types of
training methods-instruction-oriented and exploration-oriented were
conducted. The result of this research shows that the
instruction-oriented training method has better learning performance
than exploration-oriented training method.
Abstract: This paper deals the energy saving performance of GHP (Gas engine heat pump) air conditioning system has improved with time-series variation. There are two types of air conditioning systems, VRF (Variable refrigerant flow) and central cooling and heating system. VRF is classified as EHP (Electric driven heat pump) and GHP. EHP drives the compressor with electric motor. GHP drives the compressor with the gas engine. The electric consumption of GHP is less than one tenth of EHP does.
In this study, the energy consumption data of GHP installed the junior high schools was collected. An annual and monthly energy consumption per rated thermal output power of each apparatus was calculated, and then their energy efficiency was analyzed. From these data, we investigated improvement of the energy saving of the GHP air conditioning system by the change in the generation.
Abstract: Antioxidants contribute to endogenous photoprotection
and are important for the maintenance of skin health. The study was carried out to compare the skin hydration and transepidermal
water loss (TEWL) effects of a stable cosmetic preparation
containing flavonoids, following two applications a day over a period
of tenth week. The skin trans-epidermal water loss and skin hydration
effect was measured at the beginning and up to the end of study period of ten weeks. Any effect produced was measured by Corneometer and TEWA meter (Non-invasive probe).
Two formulations were developed for this study design. Formulation one the control formulation in which no apple juice
extract( Flavonoids) was incorporated while second one was the active formulation in which the apple juice extract (3%) containing
flavonoids was incorporated into water in oil emulsion using Abil EM 90 as an emulsifier. Stable formulations (control and Active)
were applied on human cheeks (n = 12) for a study period of 10 weeks. Result of each volunteer of skin hydration and TEWL was
measured by corneometer and TEWA meter. By using ANOVA and Paired sample t test as a statistical evaluation, result of both base and
formulation were compared. Statistical significant results (p≤0.05)
were observed regarding skin hydration and TEWL when two creams, control and Formulation were compared. It showed that
desired formulation (Active) may have interesting application as an
active moisturizing cream on healthy skin.
Abstract: The purpose of this paper is to guide the effort in
improving the economic added value of Indonesian fisheries product
through post fishing program, which is cold storage program.
Indonesia's fisheries potential has been acknowledged by the world.
FAO (2009) stated that Indonesia is one of the tenth highest
producers of fishery products in the world. Based on BPS (Statistics
Indonesia data), the national fisheries production in 2011 reached
5.714 million tons, which 93.55% came from marine fisheries and
6.45% from open waters. Indonesian territory consist of 2/3 of
Indonesian waters, has given enormous benefits for Indonesia,
especially fishermen. To improve the economic level of fishermen
requires efforts to develop fisheries business unit. On of the efforts is
by improving the quality of products which are marketed in the
regional and international levels. It is certainly need the support of
the existence of various fishery facilities (infrastructure to
superstructure), one of which is cold storage. Given the many
benefits of cold storage as a means of processing of fishery resources,
Indonesia Maritime Security Coordinating Board (IMSCB) as one of
the maritime institutions for maritime security and safety, has a
program to empower the coastal community through encourages the
development of cold storage in the middle and lower fishery business
unit. The development of cold storage facilities which able to run its
maximum role requires synergistic efforts of various parties.
Abstract: Paper deals with the topic of questions as important
components of information behavior in the school. By analyzing the
Corpus Schola2010, the state of contemporary education in terms of
questioning is proven unsatisfactory: 80% of the questions are asked
by teachers; most of teacher-s questions are asked at the beginning of
the first grade, than their number decreases and is settling down on
80±10 questions per lesson. The average number of questions within
one lesson per one pupil is generally less than one whole question.
The highest values are achieved in the first, sixth, eighth and tenth
grade,, i.e. in the transition years in which pupils are moving into
higher levels of education and every following year it declines. We
can state Czech school do not support questioning and question skill
of their pupils, thereby typical Czech schools are neglecting the
development of thinking, reasoning and cooperation of their pupils.
Abstract: In this work, the autoregressive vectors are used to
know dynamics of the Agricultural export and import, and the real
effective exchange rate (REER). In order to analyze the interactions,
the impulse- response function is used in decomposition of variance,
causality of Granger as well as the methodology of Johansen to know
the relations co integration. The REER causes agricultural export and
import in the sense of Granger. The influence displays the
innovations of the REER on the agricultural export and import is not
very great and the duration of the effects is short. It displays that
REER has an immediate positive effect, after the tenth year it
displays smooth results on the agricultural export. Evidence of a
vector exists co integration, In short run, REER has smaller effects
on export and import, compared to the long-run effects.
Abstract: A mobile ad hoc network is a network of mobile nodes
without any notion of centralized administration. In such a network,
each mobile node behaves not only as a host which runs applications
but also as a router to forward packets on behalf of others. Clustering
has been applied to routing protocols to achieve efficient
communications. A CH network expresses the connected relationship
among cluster-heads. This paper discusses the methods for
constructing a CH network, and produces the following results: (1)
The required running costs of 3 traditional methods for constructing a
CH network are not so different from each other in the static
circumstance, or in the dynamic circumstance. Their running costs in
the static circumstance do not differ from their costs in the dynamic
circumstance. Meanwhile, although the routing costs required for the
above 3 methods are not so different in the static circumstance, the
costs are considerably different from each other in the dynamic
circumstance. Their routing costs in the static circumstance are also
very different from their costs in the dynamic circumstance, and the
former is one tenths of the latter. The routing cost in the dynamic
circumstance is mostly the cost for re-routing. (2) On the strength of
the above results, we discuss new 2 methods regarding whether they
are tolerable or not in the dynamic circumstance, that is, whether the
times of re-routing are small or not. These new methods are revised
methods that are based on the traditional methods. We recommended
the method which produces the smallest routing cost in the dynamic
circumstance, therefore producing the smallest total cost.
Abstract: Background: Regular physical activity contributes
positively to physical and psychological health. In the present study,
the stages of change of physical activity and the total physical
Aims: The aim of this study was to investigate the proportion of
adolescent girls in each stages of change and the causative factors
associated with physical activity such as the related social support
and self efficacy in a sample of the high school students.
Methods: In this study, Social Cognitive Theory (SCT) and the
Transtheorical Model (TTM) guided instrument development. The
data regarding the demographics, psychosocial determinants of
physical activity, stage of change and physical activity was gathered
by questionnaires. Several measures of psychosocial determinants of
physical activity were translated from English into Persian using the
back-translation technique. These translated measures were
administered to 512 ninth and tenth-grade Iranian high school
students for factor analysis.
Results: The distribution of the stage of change for physical activity
was as follow: 18/5% in precontemplation, 23.4% in contemplation,
38.2% in preparation, 4.6% in action and 15.3% in maintenance.
They were in 80.1% pre-adoption stages (precontemplation stage,
contemplation stage and preparation stage) and 19.9% post-adoption
stages (action stage and maintenance stage) of physical activity.
There was a significant relate between age and physical activity in
adolescent girls (age-related decline of physical activity) p
Abstract: Chronic diseases prevailed along with economic
growth as well as life style changed in recent years in Taiwan.
According to the governmental statistics, hypertension related disease
is the tenth of death causes with 1,816 died directly from hypertension
in 2010. There were more death causes amongst the top ten had been
proofed that having strong association with the hypertension, such as
heart diseases, cardiovascular diseases, and diabetes. Hypertension or
High blood pressure is one of the major indicators for chronic diseases,
and was generally perceived as the major causes of mortality. The
literature generally suggested that regular physical exercise was
helpful to prevent the occurrence or to ease the progress of a
hypertension. This paper reported the process and outcomes in
detailed of an improvement project of physical exercise intervention
specific for hypertension patients. Physical information were
measured before and after the project to obtain information such as
weight, waistline, cholesterol (HD & LD), blood examination, as well
as self-perceived health status. The intervention project involved a
six-week exercise program, of which contained three times a week, 30
minutes of tutored physical exercise intervention. The project had
achieved several gains in changing the subjects- behavior in terms of
many important biophysical indexes. Around 20% of the participants
had significantly improved their cholesterols, BMI, and changed
unhealthy behaviors. Results from the project were encouraging, and
would be good reference for other samples.