Abstract: This study was an investigation on the suitability of Lahar/HDPE composite as a primary material for low-cost smallscale biogas digesters. While sources of raw materials for biogas are abundant in the Philippines, cost of the technology has made the widespread utilization of this resource an indefinite proposition. Aside from capital economics, another problem arises with space requirements of current digester designs. These problems may be simultaneously addressed by fabricating digesters on a smaller, household scale to reach a wider market, and to use materials that may accommodate optimization of overall design and fabrication cost without sacrificing operational efficiency. This study involved actual fabrication of the Lahar/HDPE composite at varying composition and geometry, subsequent mechanical and thermal characterization, and implementation of Statistical Analysis to find intrinsic relationships between variables. From the results, Lahar/HDPE composite was found to be feasible for use as digester material from both mechanical and economic standpoints.
Abstract: Reliable water level forecasts are particularly
important for warning against dangerous flood and inundation. The
current study aims at investigating the suitability of the adaptive
network based fuzzy inference system for continuous water level
modeling. A hybrid learning algorithm, which combines the least
square method and the back propagation algorithm, is used to
identify the parameters of the network. For this study, water levels
data are available for a hydrological year of 2002 with a sampling
interval of 1-hour. The number of antecedent water level that should
be included in the input variables is determined by two statistical
methods, i.e. autocorrelation function and partial autocorrelation
function between the variables. Forecasting was done for 1-hour until
12-hour ahead in order to compare the models generalization at
higher horizons. The results demonstrate that the adaptive networkbased
fuzzy inference system model can be applied successfully and
provide high accuracy and reliability for river water level estimation.
In general, the adaptive network-based fuzzy inference system
provides accurate and reliable water level prediction for 1-hour ahead
where the MAPE=1.15% and correlation=0.98 was achieved. Up to
12-hour ahead prediction, the model still shows relatively good
performance where the error of prediction resulted was less than
9.65%. The information gathered from the preliminary results
provide a useful guidance or reference for flood early warning
system design in which the magnitude and the timing of a potential
extreme flood are indicated.
Abstract: Rotor Flux based Model Reference Adaptive System
(RF-MRAS) is the most popularly used conventional speed
estimation scheme for sensor-less IM drives. In this scheme, the
voltage model equations are used for the reference model. This
encounters major drawbacks at low frequencies/speed which leads to
the poor performance of RF-MRAS. Replacing the reference model
using Neural Network (NN) based flux estimator provides an
alternate solution and addresses such drawbacks. This paper
identifies an NN based flux estimator using Single Neuron Cascaded
(SNC) Architecture. The proposed SNC-NN model replaces the
conventional voltage model in RF-MRAS to form a novel MRAS
scheme named as SNC-NN-MRAS. Through simulation the proposed
SNC-NN-MRAS is shown to be promising in terms of all major
issues and robustness to parameter variation. The suitability of the
proposed SNC-NN-MRAS based speed estimator and its advantages
over RF-MRAS for sensor-less induction motor drives is
comprehensively presented through extensive simulations.
Abstract: The Taiwan government has started to promote the “Plain Landscape Afforestation and Greening Program" since 2002. A key task of the program was the payment for environmental services (PES), entitled the “Plain Landscape Afforestation Policy" (PLAP), which was certificated by the Executive Yuan on August 31, 2001 and enacted on January 1, 2002. According to the policy, it is estimated that the total area of afforestation will be 25,100 hectares by December 31, 2007. Until the end of 2007, the policy had been enacted for six years in total and the actual area of afforestation was 8,919.18 hectares. Among them, Taiwan Sugar Corporation (TSC) was accounted for 7,960 hectares (with 2,450.83 hectares as public service area) which occupied 86.22% of the total afforestation area; the private farmland promoted by local governments was accounted for 869.18 hectares which occupied 9.75% of the total afforestation area. Based on the above, we observe that most of the afforestation area in this policy is executed by TSC, and the achievement ratio by TSC is better than by others. It implies that the success of the PLAP is seriously related to the execution of TSC. The objective of this study is to analyze the relevant policy planning of TSC's participation in the PLAP, suggest complementary measures, and draw up effective adjustment mechanisms, so as to improve the effectiveness of executing the policy. Our main conclusions and suggestions are summarized as follows: 1. The main reason for TSC’s participation in the PLAP is based on their passive cooperation with the central government or company policy. Prior to TSC’s participation in the PLAP, their lands were mainly used for growing sugarcane. 2. The main factors of TSC's consideration on the selection of tree species are based on the suitability of land and species. The largest proportion of tree species is allocated to economic forests, and the lack of technical instruction was the main problem during afforestation. Moreover, the method of improving TSC’s future development in leisure agriculture and landscape business becomes a key topic. 3. TSC has developed short and long-term plans on participating in the PLAP for the future. However, there is no great willingness or incentive on budgeting for such detailed planning. 4. Most people from TSC interviewed consider the requirements on PLAP unreasonable. Among them, an unreasonable requirement on the number of trees accounted for the greatest proportion; furthermore, most interviewees suggested that the government should continue to provide incentives even after 20 years. 5. Since the government shares the same goals as TSC, there should be sufficient cooperation and communication that support the technical instruction and reduction of afforestation cost, which will also help to improve effectiveness of the policy.
Abstract: Does a communication modality matter in delivering e-learning information? With the recent growth of broadcasting systems, media technologies and e-learning contents, various systems with different communication modalities have been introduced. In accordance with these trends, this study examines the effects of the information delivery modality on psychology of students. Findings from an experiment indicated that the delivering information which includes a video modality elicited higher degrees of credibility, quality, representativeness of content, and perceived suitability for delivering information than those of auditory information. However, there is no difference between content liking and attitude. The Implications of the findings and the limitations are discussed.
Abstract: Recently, a vehicular ad-hoc networks(VANETs) for
Intelligent Transport System(ITS) have become able safety and convenience services surpassing the simple services such as
an electronic toll collection system. To provide the proper services,
VANET needs infrastructure over the country infrastructure. Thus, we have to spend a huge sum of
human resources. In this reason, several studies have been made on the
usage of cellular networks instead of new protocols
this study is to assess a performance evaluation of the
cellular network for VANET. In this paper, the result of a
for the suitability of cellular networks for VANET
experiment, The LTE(Long Term Evolution) of cellular networks found to be most suitable among the others cellular networks
Abstract: The paper describes ergonomics problems trend of
student at B5101 classroom building 2, Suranaree University of
Technology. The objective to survey ergonomics problems and effect
from use chairs for sitting in class room. The result from survey
method 100 student they use lecture chair for sitting in classroom
more than 2 hours/ day by RULA[1]. and Body discomfort survey[2].
The result from Body discomfort survey contribute fatigue problems
at neck, lower back, upper back and right shoulder 2.93, 2.91, 2.33,
1.75 respectively and result from RULA contribute fatigue problems
at neck, body and right upper arm 4.00, 3.75 and 3.00 respectively
are consistent. After that the researcher provide improvement plan
for design new chair support student fatigue reduction by prepare
data of sample anthropometry and design ergonomics chair prototype
3 unit. Then sample 100 student trial to use new chair and evaluate
again by RULA, Body discomfort and satisfaction. The result from
trial new chair after improvement by RULA present fatigue reduction
average of head and neck from 4.00 to 2.25 , body and trunk from
3.75 to 2.00 and arm force from 1.00 to 0.25 respectively. The result
from trial new chair after improvement by Body discomfort present
fatigue reduction average of lower back from 2.91 to 0.87, neck from
2.93 to 1.24, upper back 2.33 to 0.84 and right upper arm from 1.75
to 0.74. That statistical of RULA and Body discomfort survey
present fatigue reduction after improvement significance with a
confidence level of 95% (p-value 0.05). When analyzing the
relationship of fatigue as part of the body by Chi – square test during
RULA and Body discomfort that before and after improvements were
consistent with the significant level of confidence 95% (p-value 0.05)
. Moreover the students satisfaction result from trial with a new chair
for 30 minutes [3]. 72 percent very satisfied of the folding of the
secondary writing simple 66% the width of the writing plate, 64% the
suitability of the writing plate, 62% of soft seat cushion and 61%
easy to seat the chair.
Abstract: A feature weighting and selection method is proposed
which uses the structure of a weightless neuron and exploits the
principles that govern the operation of Genetic Algorithms and
Evolution. Features are coded onto chromosomes in a novel way
which allows weighting information regarding the features to be
directly inferred from the gene values. The proposed method is
significant in that it addresses several problems concerned with
algorithms for feature selection and weighting as well as providing
significant advantages such as speed, simplicity and suitability for
real-time systems.
Abstract: During the last decade Panicum virgatum, known as
Switchgrass, has been broadly studied because of its remarkable
attributes as a substitute pasture and as a functional biofuel source.
The objective of this investigation was to establish soil suitability for
Switchgrass in the State of Mississippi. A linear weighted additive
model was developed to forecast soil suitability. Multicriteria
analysis and Sensitivity analysis were utilized to adjust and optimize
the model. The model was fit using seven years of field data
associated with soils characteristics collected from Natural Resources
Conservation System - United States Department of Agriculture
(NRCS-USDA). The best model was selected by correlating
calculated biomass yield with each model's soils-based output for
Switchgrass suitability. Coefficient of determination (r2) was the
decisive factor used to establish the 'best' soil suitability model.
Coefficients associated with the 'best' model were implemented
within a Geographic Information System (GIS) to create a map of
relative soil suitability for Switchgrass in Mississippi. A Geodatabase
associated with soil parameters was built and is available for future
Geographic Information System use.
Abstract: Large metal and concrete structures suffer by various kinds of deterioration, and accurate prediction of the remaining life is important. This paper informs about two methods for its assessment. One method, suitable for steel bridges and other constructions exposed to fatigue, monitors the loads and damage accumulation using information systems for the operation and the finite element model of the construction. In addition to the operation load, the dead weight of the construction and thermal stresses can be included into the model. The second method is suitable for concrete bridges and other structures, which suffer by carbonatation and other degradation processes, driven by diffusion. The diffusion constant, important for the prediction of future development, can be determined from the depth-profile of pH, obtained by pH measurement at various depths. Comparison with measurements on real objects illustrates the suitability of both methods.
Abstract: The myoelectric signal (MES) is one of the Biosignals
utilized in helping humans to control equipments. Recent approaches
in MES classification to control prosthetic devices employing pattern
recognition techniques revealed two problems, first, the classification
performance of the system starts degrading when the number of
motion classes to be classified increases, second, in order to solve the
first problem, additional complicated methods were utilized which
increase the computational cost of a multifunction myoelectric
control system. In an effort to solve these problems and to achieve a
feasible design for real time implementation with high overall
accuracy, this paper presents a new method for feature extraction in
MES recognition systems. The method works by extracting features
using Wavelet Packet Transform (WPT) applied on the MES from
multiple channels, and then employs Fuzzy c-means (FCM)
algorithm to generate a measure that judges on features suitability for
classification. Finally, Principle Component Analysis (PCA) is
utilized to reduce the size of the data before computing the
classification accuracy with a multilayer perceptron neural network.
The proposed system produces powerful classification results (99%
accuracy) by using only a small portion of the original feature set.
Abstract: Energy generated by the force of water in hydropower
can provide a more sustainable, non-polluting alternative to fossil
fuels, along with other renewable sources of energy, such as wind,
solar and tidal power, bio energy and geothermal energy. Small scale
hydroelectricity in Iran is well suited for “off-grid" rural electricity
applications, while other renewable energy sources, such as wind,
solar and biomass, can be beneficially used as fuel for pumping
groundwater for drinking and small scale irrigation in remote rural
areas or small villages. Small Hydro Power plants in Iran have very
low operating and maintenance costs because they consume no fossil
or nuclear fuel and do not involve high temperature processes. The
equipment is relatively simple to operate and maintain. Hydropower
equipment can adjust rapidly to load changes. The extended
equipment life provides significant economic advantages. Some
hydroelectric plants installed 100 years ago still operate reliably. The
Polkolo river is located on Karun basin at southwest of Iran. Situation
and conditions of Polkolo river are evaluated for construction of
small hydropower in this article. The topographical conditions and
the existence of permanent water from springs provide the suitability
to install hydroelectric power plants on the river Polkolo. The
cascade plant consists of 9 power plants connected with each other
and is having the total head as 1100m and discharge about 2.5cubic
meter per second. The annual production of energy is 105.5 million
kwh.
Abstract: The Requirements Abstraction Model (RAM) helps in managing abstraction in requirements by organizing them at four levels (product, feature, function and component). The RAM is adaptable and can be tailored to meet the needs of the various organizations. Because software requirements are an important source of information for developing high-level tests, organizations willing to adopt the RAM model need to know the suitability of the RAM requirements for developing high-level tests. To investigate this suitability, test cases from twenty randomly selected requirements were developed, analyzed and graded. Requirements were selected from the requirements document of a Course Management System, a web based software system that supports teachers and students in performing course related tasks. This paper describes the results of the requirements document analysis. The results show that requirements at lower levels in the RAM are suitable for developing executable tests whereas it is hard to develop from requirements at higher levels.
Abstract: The current of professional bicycle pedal-s
manufacturing model mostly used casting, forging, die-casting
processing methods, so the paper used 7075 aluminum alloy which is
to produce the bicycle parts most commonly, and employs the
rigid-plastic finite element (FE) DEFORMTM 3D software to simulate
and to analyze the professional bicycle pedal design. First we use Solid
works 2010 3D graphics software to design the professional bicycle
pedal of the mold and appearance, then import finite element (FE)
DEFORMTM 3D software for analysis. The paper used rigid-plastic
model analytical methods, and assuming mode to be rigid body. A
series of simulation analyses in which the variables depend on
different temperature of forging billet, friction factors, forging speed,
mold temperature are reveal to effective stress, effective strain, damage
and die radial load distribution for forging bicycle pedal. The analysis
results hope to provide professional bicycle pedal forming mold
references to identified whether suit with the finite element results for
high-strength design suitability of aluminum alloy.
Abstract: Our adaptive multimodal system aims at correctly
presenting a mathematical expression to visually impaired users.
Given an interaction context (i.e. combination of user, environment
and system resources) as well as the complexity of the expression
itself and the user-s preferences, the suitability scores of different
presentation format are calculated. Unlike the current state-of-the art
solutions, our approach takes into account the user-s situation and not
imposes a solution that is not suitable to his context and capacity. In
this wok, we present our methodology for calculating the
mathematical expression complexity and the results of our
experiment. Finally, this paper discusses the concepts and principles
applied on our system as well as their validation through cases
studies. This work is our original contribution to an ongoing research
to make informatics more accessible to handicapped users.
Abstract: The aim of current research was to investigate ASLT method suitability for accelerated beer shelf-life determination. The research was accomplished on popular Latvian beer: light filtrated and unfiltered pasteurized beer with alcohol content 5.2%; dark filtrated pasteurized beer with alcohol content 4.2% with shelf-life five months. Bottled in dark glass bottles beer samples were storage during 20 weeks at several temperature regimes: +10±1 °C, +20±1 °C, +30±1 °C, +40±1 °C. Samples quality parameters as physically-chemical and microbiological was tested every two weeks using standard methods. It is possible to determine beer shelf-life rapidly during storage at +30±1 °C for filtered pasteurized light beer by 2.5 times, unfiltered pasteurized light beer by 1.4 times and for filtered pasteurized dark beer by 1.7 times. During preset experiments it was proved, that it is possible to determine beer shelf-life rapidly using ASLT method if beer storage temperature could be increased by +10±1 °C.
Abstract: Cements, which are intrinsically brittle materials, can
exhibit a degree of pseudo-ductility when reinforced with a sufficient
volume fraction of a fibrous phase. This class of materials, called
Engineered Cement Composites (ECC) has the potential to be used in
future tunneling applications where a level of pseudo-ductility is
required to avoid brittle failures. However uncertainties remain
regarding mechanical performance. Previous work has focused on
comparatively thin specimens; however for future civil engineering
applications, it is imperative that the behavior in tension of thicker
specimens is understood. In the present work, specimens containing
cement powder and admixtures have been manufactured following
two different processes and tested in tension. Multiple matrix
cracking has been observed during tensile testing, leading to a
“strain-hardening" behavior, confirming the possible suitability of
ECC material when used as thick sections (greater than 50mm) in
tunneling applications.
Abstract: This paper presents data annotation models at
five levels of granularity (database, relation, column, tuple, and cell) of relational data to address the problem of unsuitability of most relational databases to express annotations. These models
do not require any structural and schematic changes to the
underlying database. These models are also flexible, extensible,
customizable, database-neutral, and platform-independent. This paper also presents an SQL-like query language, named Annotation Query Language (AnQL), to query annotation documents. AnQL is simple to understand and exploits the already-existent wide knowledge and skill set of SQL.
Abstract: This paper discusses site selection process for
biological soil conservation planning. It was supported by a valuefocused
approach and spatial multi-criteria evaluation techniques. A
first set of spatial criteria was used to design a number of potential
sites. Next, a new set of spatial and non-spatial criteria was
employed, including the natural factors and the financial costs,
together with the degree of suitability for the Bonkuh watershed to
biological soil conservation planning and to recommend the most
acceptable program. The whole process was facilitated by a new
software tool that supports spatial multiple criteria evaluation, or
SMCE in GIS software (ILWIS). The application of this tool,
combined with a continual feedback by the public attentions, has
provided an effective methodology to solve complex decisional
problem in biological soil conservation planning.
Abstract: Geopolymer cement was evaluated as wellbore sealing material for carbon dioxide geosequestration application. Curing of cement system in saline water and strength testing in triaxial stress state condition under lateral confinement is relevant to primary cementing in CO2 geosequestration wellbore in saline aquifer. Geopolymer cement was cured in saline water (both at ambient conditions for 28 days and heated (60°C) conditions for 12 hours) and tested for triaxial strength at different levels of lateral confinement. Normal water and few other curing techniques were also studied both for geopolymer and API ‘G’ cement. Results reported were compared to evaluate the suitability of saline water for curing of geopolymer cement. Unconfined compression test results showed higher strength for curing in saline water than normal water. Besides, testing strength under lateral confinement demonstrated the material failure behavior from brittle to plastic.