Abstract: The performance of a permanent magnet brushless direct current (BLDC) motor controlled by the Kalman filter based position-sensorless drive is studied in terms of its dependence from the system’s parameters variations. The effects of the system’s parameters changes on the dynamic behavior of state variables are verified. Simulated is the closed loop control scheme with Kalman filter in the feedback line. Distinguished are two separate data sampling modes in analyzing feedback output from the BLDC motor: (1) equal angular separation and (2) equal time intervals. In case (1), the data are collected via equal intervals of rotor’s angular position i, i.e. keeping = const. In case (2), the data collection time points ti are separated by equal sampling time intervals t = const. Demonstrated are the effects of the parameters changes on the sensorless control flow, in particular, reduction of the instability torque ripples, switching spikes, and torque load balancing. It is specifically shown that an efficient suppression of commutation induced instability torque ripples is an achievable selection of the sampling rate in the Kalman filter settings above a certain critical value. The computational cost of such suppression is shown to be higher for the motors with lower induction values of the windings.
Abstract: This paper presents open-loop vector control method of induction motor with space vector pulse width modulation (SVPWM) technique. Normally, the closed loop speed control is preferred and is believed to be more accurate. However, it requires a position sensor to track the rotor position which is not desirable to use it for certain workspace applications. This paper exhibits the performance of three-phase induction motor with the simplest control algorithm without the use of a position sensor nor an estimation block to estimate rotor position for sensorless control. The motor stator currents are measured and are transformed to synchronously rotating (d-q-axis) frame by use of Clarke and Park transformation. The actual control happens in this frame where the measured currents are compared with the reference currents. The error signal is fed to a conventional PI controller, and the corrected d-q voltage is generated. The controller outputs are transformed back to three phase voltages and are fed to SVPWM block which generates PWM signal for the voltage source inverter. The open loop vector control model along with SVPWM algorithm is modeled in MATLAB/Simulink software and is experimented and validated in TMS320F28335 DSP board.
Abstract: This paper presents a speed estimation scheme based
on second-order sliding-mode Super Twisting Algorithm (STA) and
Model Reference Adaptive System (MRAS) estimation theory for
Sensorless control of multiphase induction machine. A stator current
observer is designed based on the STA, which is utilized to take the
place of the reference voltage model of the standard MRAS
algorithm. The observer is insensitive to the variation of rotor
resistance and magnetizing inductance when the states arrive at the
sliding mode. Derivatives of rotor flux are obtained and designed as
the state of MRAS, thus eliminating the integration. Compared with
the first-order sliding-mode speed estimator, the proposed scheme
makes full use of the auxiliary sliding-mode surface, thus alleviating
the chattering behavior without increasing the complexity. Simulation
results show the robustness and effectiveness of the proposed
scheme.
Abstract: Multiphase Induction Machine (IM) is normally
controlled using rotor field oriented vector control. Under phase(s)
loss, the machine currents can be optimally controlled to satisfy
certain optimization criteria. In this paper we discuss the performance
of double manifold sliding mode observer (DM-SMO) in Sensorless
control of multiphase induction machine under unsymmetrical
condition (one phase loss). This observer is developed using the IM
model in the stationary reference frame. DM-SMO is constructed by
adding extra feedback term to conventional single mode sliding mode
observer (SM-SMO) which proposed in many literature. This leads to
a fully convergent observer that also yields an accurate estimate of
the speed and stator currents. It will be shown by the simulation
results that the estimated speed and currents by the method are very
well and error between real and estimated quantities is negligible.
Also parameter sensitivity analysis shows that this method is rather
robust against parameter variation.
Abstract: This paper deals with stability analysis for synchronous reluctance motors drive. Special attention is paid to the transient performance with variations in motor's parameters such as Ld and Rs. A study of the dynamic control using d-q model is presented first in order to clarify the stability of the motor drive system. Based on the experimental parameters of the synchronous reluctance motor, this paper gives some simulation results using MATLAB/SIMULINK software packages. It is concluded that the motor parameters, especially Ld, affect the estimator stability and hence the whole drive system.
Abstract: In this paper, we show that the association of the PI
regulators for the speed and stator currents with a control strategy
using the linearization by state feedback for an induction machine
without speed sensor, and with an adaptation of the rotor resistance.
The rotor speed is estimated by using the model reference adaptive
system approach (MRAS). This method consists of using two
models: The first is the reference model and the second is an
adjustable one in which two components of the stator flux, obtained
from the measurement of the currents and stator voltages are
estimated. The estimated rotor speed is then obtained by canceling
the difference between stator-flux of the reference model and those
of the adjustable one. Satisfactory results of simulation are obtained
and discussed in this paper to highlight the proposed approach.
Abstract: The recent trend in field oriented control (FOC) is towards the use of sensorless techniques that avoid the use of speed sensor and flux sensor. Sensors are replaced by estimators or observers to minimise the cost and increase the reliability. In this paper an anlyse of perfomance of a MRAS used in sensorless control of induction motors and sensitvity to machine parameters change are studied.
Abstract: Adaptive observers used in sensorless control of induction motors suffer from instability especally in regenerating mode. In this paper, an optimal feed back gain design is proposed, it can reduce the instability region in the torque speed plane .
Abstract: In this paper, a direct torque control - space vector
modulation (DTC-SVM) scheme is presented for a six-phase speed
and voltage sensorless induction motor (IM) drive. The decoupled
torque and stator flux control is achieved based on IM stator flux field orientation. The rotor speed is detected by on-line estimating of
the rotor angular slip speed and stator vector flux speed. In addition, a simple method is introduced to estimate the stator resistance.
Moreover in this control scheme the voltage sensors are eliminated
and actual motor phase voltages are approximated by using PWM
inverter switching times and the dc link voltage. Finally, some simulation and experimental results are presented to verify the
effectiveness and capability of the proposed control scheme.
Abstract: This paper describes the speed sensorless vector control method of the parallel connected induction motor drive fed by a single inverter. Speed and rotor fluxes of the induction motor are estimated by natural observer with load torque adaptation and adaptive rotor flux observer. The performance parameters speed and rotor fluxes are estimated from the measured terminal voltages and currents. Fourth order induction motor model is used and speed is considered as a parameter. The performance of the natural observer is similar to the conventional observer. The speed of an induction motor is estimated by MATLAB simulation under different speed and load conditions. Estimated values along with other measured states are used for closed loop control. The simulation results show that the natural observer is also effective for parallel connected induction motor drive.
Abstract: Speed sensorless systems are intensively studied during recent years; this is mainly due to their economical benefit and fragility of mechanical sensors and also the difficulty of installing this type of sensor in many applications. These systems suffer from instability problems and sensitivity to parameter mismatch at low speed operation. In this paper an analysis of adaptive observer stability with stator resistance estimation is given.