Abstract: This article is focused on the calculation of heat
radiation intensity and its optimization on an aluminum mould
surface. The inside of the mould is sprinkled with a special powder
and its outside is heated by infra heaters located above the mould
surface, up to a temperature of 250°C. By this way artificial leathers
in the car industry are produced (e. g. the artificial leather on a car
dashboard). A mathematical model of heat radiation of infra heaters
on a mould surface is described in this paper. This model allows us to
calculate a heat-intensity radiation on the mould surface for the
concrete location of infra heaters above the mould surface. It is
necessary to ensure approximately the same heat intensity radiation
on the mould surface by finding a suitable location for the infra
heaters, and in this way the same material structure and color of
artificial leather. In the model we have used a genetic algorithm to
optimize the radiation intensity on the mould surface. Experimental
measured values for the heat radiation intensity by a sensor in the
surroundings of an infra heater are used for the calculation
procedures. A computational procedure was programmed in language
Matlab.
Abstract: Increase in using internet makes some problems that
one of them is "internet anxiety". Internet anxiety is a type of anxious
that people may feel during surfing internet or using internet for their
educational purpose, blogging or streaming to digital libraries. The
goal of this study is evaluating of internet anxiety among the
management students. In this research Ealy's internet anxiety
questionnaire, consists of positive and negative items, is completed
by 310 participants. According to the findings, about 64.7% of them
were equal or below to mean anxiety score (50). The distribution of
internet anxiety scores was normal and there was no meaningful
difference between men-s and women's anxiety level in this sample.
Results also showed that there is no meaningful difference of internet
anxiety level between different fields of study in Management. This
evaluation will help managers to perform gap analysis between the
existent level and the desired one. Future work would be providing
techniques for abating human anxiety while using internet via human
computer interaction techniques.
Abstract: Transition theory has been used to derive the elasticplastic
and transitional stresses. Results obtained have been discussed
numerically and depicted graphically. It is observed that the rotating
disk made of incompressible material with inclusion require higher
angular speed to yield at the internal surface as compared to disk
made of compressible material. It is seen that the radial and
circumferential stresses are maximum at the internal surface with and
without edge load (for flat disk). With the increase in thickness
parameter (k = 2, 4), the circumferential stress is maximum at the
external surface while the radial stress is maximum at the internal
surface. From the figures drawn the disk with exponentially varying
thickness (k = 2), high angular speed is required for initial yielding at
internal surface as compared to flat disk and exponentially varying
thickness for k = 4 onwards. It is concluded that the disk made of
isotropic compressible material is on the safer side of the design as
compared to disk made of isotropic incompressible material as it
requires higher percentage increase in an angular speed to become
fully plastic from its initial yielding.
Abstract: Evaluation of contact pressure, surface and
subsurface contact stresses are essential to know the functional
response of surface coatings and the contact behavior mainly depends
on surface roughness, material property, thickness of layer and the
manner of loading. Contact parameter evaluation of real rough
surface contacts mostly relies on statistical single asperity contact
approaches. In this work, a three dimensional layered solid rough
surface in contact with a rigid flat is modeled and analyzed using
finite element method. The rough surface of layered solid is
generated by FFT approach. The generated rough surface is exported
to a finite element method based ANSYS package through which the
bottom up solid modeling is employed to create a deformable solid
model with a layered solid rough surface on top. The discretization
and contact analysis are carried by using the same ANSYS package.
The elastic, elastoplastic and plastic deformations are continuous in
the present finite element method unlike many other contact models.
The Young-s modulus to yield strength ratio of layer is varied in the
present work to observe the contact parameters effect while keeping
the surface roughness and substrate material properties as constant.
The contacting asperities attain elastic, elastoplastic and plastic states
with their continuity and asperity interaction phenomena is inherently
included. The resultant contact parameters show that neighboring
asperity interaction and the Young-s modulus to yield strength ratio
of layer influence the bulk deformation consequently affect the
interface strength.
Abstract: Attachment of the circulating monocytes to the
endothelium is the earliest detectable events during formation of
atherosclerosis. The adhesion molecules, chemokines and matrix
proteases genes were identified to be expressed in atherogenesis.
Expressions of these genes may influence structural integrity of the
luminal endothelium. The aim of this study is to relate changes in the
ultrastructural morphology of the aortic luminal surface and gene
expressions of the endothelial surface, chemokine and MMP-12 in
normal and hypercholesterolemic rabbits. Luminal endothelial
surface from rabbit aortic tissue was examined by scanning electron
microscopy (SEM) using low vacuum mode to ascertain
ultrastructural changes in development of atherosclerotic lesion. Gene
expression of adhesion molecules, MCP-1 and MMP-12 were studied
by Real-time PCR. Ultrastructural observations of the aortic luminal
surface exhibited changes from normal regular smooth intact
endothelium to irregular luminal surface including marked globular
appearance and ruptures of the membrane layer. Real-time PCR
demonstrated differentially expressed of studied genes in
atherosclerotic tissues. The appearance of ultrastructural changes in
aortic tissue of hypercholesterolemic rabbits is suggested to have
relation with underlying changes of endothelial surface molecules,
chemokine and MMP-12 gene expressions.
Abstract: Space exploration is a highly visible endeavour of
humankind to seek profound answers to questions about the origins
of our solar system, whether life exists beyond Earth, and how we
could live on other worlds. Different platforms have been utilized in
planetary exploration missions, such as orbiters, landers, rovers, and
penetrators.
Having low mass, good mechanical contact with the surface,
ability to acquire high quality scientific subsurface data, and ability to
be deployed in areas that may not be conducive to landers or rovers,
Penetrators provide an alternative and complimentary solution that
makes possible scientific exploration of hardly accessible sites (icy
areas, gully sites, highlands etc.).
The Canadian Space Agency (CSA) has put space exploration as
one of the pillars of its space program, and established ExCo program
to prepare Canada for future international planetary exploration.
ExCo sets surface mobility as its focus and priority, and invests
mainly in the development of rovers because of Canada's niche space
robotics technology. Meanwhile, CSA is also investigating how
micro-penetrators can help Canada to fulfill its scientific objectives
for planetary exploration.
This paper presents a review of the micro-penetrator technologies,
past missions, and lessons learned. It gives a detailed analysis of the
technical challenges of micro-penetrators, such as high impact
survivability, high precision guidance navigation and control, thermal
protection, communications, and etc. Then, a Canadian perspective of
a possible micro-penetrator mission is given, including Canadian
scientific objectives and priorities, potential instruments, and flight
opportunities.
Abstract: In this study, the contact problem of a layered composite which consists of two materials with different elastic constants and heights resting on two rigid flat supports with sharp edges is considered. The effect of gravity is neglected. While friction between the layers is taken into account, it is assumed that there is no friction between the supports and the layered composite so that only compressive tractions can be transmitted across the interface. The layered composite is subjected to a uniform clamping pressure over a finite portion of its top surface. The problem is reduced to a singular integral equation in which the contact pressure is the unknown function. The singular integral equation is evaluated numerically and the results for various dimensionless quantities are presented in graphical forms.
Abstract: Ethanol has been known for a long time, being
perhaps the oldest product obtained through traditional biotechnology
fermentation. Agriculture waste as substrate in fermentation is vastly
discussed as alternative to replace edible food and utilization of
organic material. Pineapple peel, highly potential source as substrate
is a by-product of the pineapple processing industry. Bio-ethanol
from pineapple (Ananas comosus) peel extract was carried out by
controlling fermentation without any treatment. Saccharomyces
ellipsoides was used as inoculum in this fermentation process as it is
naturally found at the pineapple skin. In this study, the capability of
Response Surface Methodology (RSM) for optimization of ethanol
production from pineapple peel extract using Saccharomyces
ellipsoideus in batch fermentation process was investigated. Effect of
five test variables in a defined range of inoculum concentration 6-
14% (v/v), pH (4.0-6.0), sugar concentration (14-22°Brix),
temperature (24-32°C) and time of incubation (30-54 hrs) on the
ethanol production were evaluated. Data obtained from experiment
were analyzed with RSM of MINITAB Software (Version 15)
whereby optimum ethanol concentration of 8.637% (v/v) was
determined. The optimum condition of 14% (v/v) inoculum
concentration, pH 6, 22°Brix, 26°C and 30hours of incubation. The
significant regression equation or model at the 5% level with
correlation value of 99.96% was also obtained.
Abstract: Characterized as rich mineral substances, low
temperature, few bacteria, and stability with numerous implementation
aspects on aquaculture, food, drinking, and leisure, the deep sea water
(DSW) development has become a new industry in the world. It has
been report that marine algae contain various biologically active
compounds. This research focued on the affections in cultivating
Sagrassum cristaefolium with different concentration of deep sea
water(DSW) and surface sea water(SSW). After two and four weeks,
the total phenolic contents were compared in Sagrassum cristaefolium
culturing with different ways, and the reductive activity of them was
also be tried with potassium ferricyanide. Those fresh seaweeds were
dried with oven and were ground to powder. Progressively, the marine
algae we cultured was extracted by water under the condition with
heating them at 90Ôäâ for 1hr.The total phenolic contents were be
executed using Folin–Ciocalteu method. The results were explaining
as follows: the highest total phenolic contents and the best reductive
ability of all could be observed on the 1/4 proportion of DSW to SSW
culturing in two weeks. Furthermore, the 1/2 proportion of DSW to
SSW also showed good reductive ability and plentiful phenolic
compositions. Finally, we confirmed that difference proportion of
DSW and SSW is the major point relating to ether the total phenolic
components or the reductive ability in the Sagrassum cristaefolium. In
the future, we will use this way to mass production the marine algae or
other micro algae on industry applications.
Abstract: Tourism is a phenomenon respected by the human communities since a long time ago. It has been evoloving continually based on a variety of social and economic needs and with respect to increasingly development of communication and considerable increase of tourist-s number and resulted exchange income has attained much out come such as employment for the communities. or the purpose of tourism development in this zone suitable times and locations need to be specified in the zone for the tourist-s attendance. One of the most important needs of the tourists is the knowledge of climate conditions and suitable times for sightseeing. In this survey, the climate trend condition has been identified for attending the tourists in Isfahan province using the modified tourism climate index (TCI) as well as SPSS, GIS, excel, surfer softwares. This index evoluates systematically the climate conditions for tourism affairs and activities using the monthly maximum mean parameters of daily temperature, daily mean temperature, minimum relative humidity, daily mean relative humidity, precipitation (mm), total sunny hours, wind speed and dust. The results obtaind using kendal-s correlation test show that the months January, February, March, April, May, June, July, August, September, October, November and December are significant and have an increasing trend that indicates the best condition for attending the tourists. S, P, T mean , T max and dust are estimated from 1976-2005 and do kendal-s correlation test again to see which parameter has been effective. Based on the test, we also observed on the effective parameters that the rate of dust in February, March, April, May, June, July, August, October and November is decreasing and precipitation in September and January is increasing and also the radiation rate in May and August is increasing that indicate a better condition of convenience. Maximum temperature in June is also decreasing. Isfahan province has two spring and fall peaks and the best places for tourism are in the north and western areas.
Abstract: The design of methods of the 20 K large dimension cold shield used for infrared radiation demarcating in space environment simulation test were introduced in this paper. The cold shield were cooled by five G-M cryocoolers , and the dimension of the cold shield is the largest in our country.Cold shield installation and distribution and compensator for contraction on cooling were introduced detailedly. The temperature distribution and cool-down time of cold shield surface were also calculated and analysed in this paper. The design of cold shield resolves the difficulty of compensator for contraction on cooling successfully. Test results show that the actual technical performance indicators of cold shield met and exceeded the design requirements.
Abstract: This paper details few mechanical modeling and
design issues of RF MEMS switches. We concentrate on an
electrostatically actuated broad side series switch; surface
micromachined with a crab leg membrane. The same results are
extended to any complex structure. With available experimental data
and fabrication results, we present the variation in dynamic
performance and compliance of the switch with reference to few
design issues, which we find are critical in deciding the dynamic
behavior of the switch, without compromise on the RF
characteristics. The optimization of pull in voltage, transient time and
resonant frequency with regard to these critical design parameters are
also presented.
Abstract: Iris localization is a very important approach in
biometric identification systems. Identification process usually is
implemented in three levels: iris localization, feature extraction, and
pattern matching finally. Accuracy of iris localization as the first step
affects all other levels and this shows the importance of iris
localization in an iris based biometric system. In this paper, we
consider Daugman iris localization method as a standard method,
propose a new method in this field and then analyze and compare the
results of them on a standard set of iris images. The proposed method
is based on the detection of circular edge of iris, and improved by
fuzzy circles and surface energy difference contexts. Implementation
of this method is so easy and compared to the other methods, have a
rather high accuracy and speed. Test results show that the accuracy of
our proposed method is about Daugman method and computation
speed of it is 10 times faster.
Abstract: In this study, the two dimensional heat conduction
problem for the dry friction clutch disc is modeled mathematically
analysis and is solved numerically using finite element method, to
determine the temperature field when band contacts occurs between
the rubbing surfaces during the operation of an automotive clutch.
Temperature calculation have been made for contact area of different
band width and the results obtained compared with these attained
when complete contact occurs. Furthermore, the effects of slipping
time and sliding velocity function are investigated as well. Both
single and repeated engagements made at regular interval are
considered.
Abstract: This paper presents the elastic buckling of
homogeneous beams with a pair of piezoelectric layers surface
bonded on both sides of the beams. The displacement field of beam is
assumed based on the Engesser-Timoshenko beam theory.
Applying the Hamilton's principle, the equilibrium equation is
established. The influences of applied voltage, dimensionless
geometrical parameter and piezoelectric thickness on the critical
buckling load of beam are presented. To investigate the accuracy of
the present analysis, a compression study is carried out with a known
data.
Abstract: Psoriasis is a widespread skin disease affecting up to 2% population with plaque psoriasis accounting to about 80%. It can be identified as a red lesion and for the higher severity the lesion is usually covered with rough scale. Psoriasis Area Severity Index (PASI) scoring is the gold standard method for measuring psoriasis severity. Scaliness is one of PASI parameter that needs to be quantified in PASI scoring. Surface roughness of lesion can be used as a scaliness feature, since existing scale on lesion surface makes the lesion rougher. The dermatologist usually assesses the severity through their tactile sense, therefore direct contact between doctor and patient is required. The problem is the doctor may not assess the lesion objectively. In this paper, a digital image analysis technique is developed to objectively determine the scaliness of the psoriasis lesion and provide the PASI scaliness score. Psoriasis lesion is modelled by a rough surface. The rough surface is created by superimposing a smooth average (curve) surface with a triangular waveform. For roughness determination, a polynomial surface fitting is used to estimate average surface followed by a subtraction between rough and average surface to give elevation surface (surface deviations). Roughness index is calculated by using average roughness equation to the height map matrix. The roughness algorithm has been tested to 444 lesion models. From roughness validation result, only 6 models can not be accepted (percentage error is greater than 10%). These errors occur due the scanned image quality. Roughness algorithm is validated for roughness measurement on abrasive papers at flat surface. The Pearson-s correlation coefficient of grade value (G) of abrasive paper and Ra is -0.9488, its shows there is a strong relation between G and Ra. The algorithm needs to be improved by surface filtering, especially to overcome a problem with noisy data.
Abstract: Drought is one of the most important natural disasters which is probable to occur in all regions with completely different climates and in addition to causing death. It results in many economic losses and social consequences. For this reason. Studying the effects and losses caused by drought which include limitation or shortage of agricultural and drinking water resources. Decreased rainfall and increased evapotranspiration. Limited plant growth and decreased agricultural products. Especially those of dry-farming. Lower levels of surface and ground waters and increased immigrations. Etc. in the country is statistical period (1988-2007) for six stations in Roudbar town were used for statistical analysis and calculating humid and dry years. The dependable rainfall index (DRI) was the main method used in this research. Results showed that during the said statistical period and also during the years 1996-1998 and 2007. more than half of the stations had faced drought. With consideration of the conducted studies. Drawing diagrams and comparing the available data with those of dry and humid years it was found that drought affected agricultural products (e.g.olive) in a way that during the year 1996 1996 drought. Olive groves of Roudbar suffered the greatest damages. Whereupon about 70% of the crops were lost.
Abstract: In this work Membrane Distillation is applied to
concentrate orange Juice. Clarified orange juice (11o Brix) obtained
from fresh fruits and a sugar solution was subjected to membrane
distillation. The experiments were performed on a flat sheet module
using orange juice and sucrose solution as feeds. The concentration
of a sucrose solution, used as a model fruit juice and also orange
juice, was carried out in a direct contact membrane distillation using
hydrophobic PTFE membrane of pore size 0.2 μm and porosity 70%.
Surface modification of PTFE membrane has been carried out by
treating membrane with alcohol and water solution to make it
hydrophilic and then hydrophobicity was regained by drying. The
influences of the feed temperature, feed concentration, flow rate,
operating time on the permeate flux were studied for treated and non
treated membrane. In this work treated and non treated membrane
were compared in terms of water flux, Within the tested range, MD
with surface modified membrane the water flux has been
significantly improved by treating the membrane surface.
Abstract: Composite of Celatom-ZeoliteY (Cel-ZY) was used to
remove cobalt ion from an aqueous solution using batch mode.
ZeoliteY has successfully superimposed on Celatom FW-14 surface
using hydrothermal treatment .The product was synthesized as a
novel of hierarchical porous material. It was observed from the
results that Cel-ZY has higher ability to remove cobalt ions than the
pure ZeoliteY powder (PZY) synthesized under the same conditions.
Several parameters were studied in this project to investigate the
effect of removal cobalt ion such as pH and initial cobalt
concentration. It was clearly observed that the uptake of cobalt ions
was affected with increase these parameters. The results proved that
the product can be used effectively to remove Co2+ ions from
wastewater as an environmentally friendly alternative.
Abstract: In this study, the sorption of Malachite green (MG) on Hydrilla verticillata biomass, a submerged aquatic plant, was investigated in a batch system. The effects of operating parameters such as temperature, adsorbent dosage, contact time, adsorbent size, and agitation speed on the sorption of Malachite green were analyzed using response surface methodology (RSM). The proposed quadratic model for central composite design (CCD) fitted very well to the experimental data that it could be used to navigate the design space according to ANOVA results. The optimum sorption conditions were determined as temperature - 43.5oC, adsorbent dosage - 0.26g, contact time - 200min, adsorbent size - 0.205mm (65mesh), and agitation speed - 230rpm. The Langmuir and Freundlich isotherm models were applied to the equilibrium data. The maximum monolayer coverage capacity of Hydrilla verticillata biomass for MG was found to be 91.97 mg/g at an initial pH 8.0 indicating that the optimum sorption initial pH. The external and intra particle diffusion models were also applied to sorption data of Hydrilla verticillata biomass with MG, and it was found that both the external diffusion as well as intra particle diffusion contributes to the actual sorption process. The pseudo-second order kinetic model described the MG sorption process with a good fitting.