Abstract: This paper present an effective method to accurately reconstruct and measure the 3D curve edges of small industrial parts based on stereo vision. To effectively fit the curve of the measured parts using a series of line segments in the images, a strategy from coarse to fine is employed based on multi-scale curve fitting. After reconstructing the 3D curve of a hole through a curved surface, its axis is adjusted so that it is parallel to the Z axis with least squares error and the dimensions of the hole can be calculated on the XY plane easily. Experimental results show that the presented method can accurately measure the dimensions of round holes through a curved surface.
Abstract: In this study, the effect of nanofluids on the pool film
boiling was experimentally investigated at saturated condition under
atmospheric pressure. For this purpose, four different water-based
nanofluids (Al2O3, SiO2, TiO2 and CuO) with 0.1% particle volume
fraction were prepared. To investigate the boiling heat transfer, a
cylindrical rod with high temperature was used. The rod heated up to
high temperatures was immersed into nanofluids. The center
temperature of rod during the cooling process was recorded by using
a K-type thermocouple. The quenching curves showed that the pool
boiling heat transfer was strongly dependent on the nanoparticle
materials. During the repetitive quenching tests, the cooling time
decreased and thus, the film boiling vanished. Consequently, the
primary reason of this was the change of the surface characteristics
due to the nanoparticles deposition on the rod-s surface.
Abstract: This work is an attempt to use the standard Smoothed
Particle Hydrodynamics methodology for the simulation of the
complex unsteady, free-surface flow in a rotating Turgo impulse
water turbine. A comparison of two different geometries was
conducted. The SPH method due to its mesh-less nature is capable of
capturing the flow features appearing in the turbine, without
diffusion at the water/air interface. Furthermore results are compared
with a commercial CFD package (Fluent®) and the SPH algorithm
proves to be capable of providing similar results, in much less time
than the mesh based CFD program. A parametric study was also
performed regarding the turbine inlet angle.
Abstract: Several studies have shown the association between
ambient particulate matter (PM) and adverse health effects and
climate change, thus highlighting the need to limit the anthropogenic
sources of PM. PM Exposure is commonly monitored as mass
concentration of PM10 (particle aerodynamic diameter < 10μm) or
PM2.5 (particle aerodynamic diameter < 2.5μm), although increasing
toxicity with decreasing aerodynamic diameter has been reported due
to increased surface area and enhanced chemical reactivity with other
species. Additionally, the light scattering properties of PM increases
with decreasing size. Hence, it is important to study the chemical
characterization of finer fraction of the particulate matter and to
identify their sources so that they can be controlled appropriately to a
large extent at the sources before reaching to the receptors.
Abstract: In this study we investigate silica nanoparticle (SiO2- NP) effects on the structure and phase properties of supported lipid monolayers and bilayers, coupling surface pressure measurements, fluorescence microscopy and atomic force microscopy. SiO2-NPs typically in size range of 10nm to 100 nm in diameter are tested. Our results suggest first that lipid molecules organization depends to their nature. Secondly, lipid molecules in the vinicity of big aggregates nanoparticles organize in liquid condensed phase whereas small aggregates are localized in both fluid liquid-expanded (LE) and liquid-condenced (LC). We demonstrated also by atomic force microscopy that by measuring friction forces it is possible to get information as if nanoparticle aggregates are recovered or not by lipid monolayers and bilayers.
Abstract: Electromyography (EMG) signal processing has been investigated remarkably regarding various applications such as in rehabilitation systems. Specifically, wavelet transform has served as a powerful technique to scrutinize EMG signals since wavelet transform is consistent with the nature of EMG as a non-stationary signal. In this paper, the efficiency of wavelet transform in surface EMG feature extraction is investigated from four levels of wavelet decomposition and a comparative study between different mother wavelets had been done. To recognize the best function and level of wavelet analysis, two evaluation criteria, scatter plot and RES index are recruited. Hereupon, four wavelet families, namely, Daubechies, Coiflets, Symlets and Biorthogonal are studied in wavelet decomposition stage. Consequently, the results show that only features from first and second level of wavelet decomposition yields good performance and some functions of various wavelet families can lead to an improvement in separability class of different hand movements.
Abstract: A composite made of plasma functionalized multiwall
carbon nanotubes (MWNTs) coated with SnO2 was synthesized by
sonochemical precipitation method. Thick layer of this
nanocomposite material was used as ethanol sensor at low
temperatures. The composite sensitivity for ethanol has increased by
a factor of 2 at room temperature and by a factor of 13 at 250°C in
comparison to that of pure SnO2. SEM image of nanocomposite
material showed MWNTs were embedded in SnO2 matrix and also a
higher surface area was observed in the presence of functionalized
MWNTs. Greatly improved sensitivity of the composite material to
ethanol can be attributed to new gas accessing passes through
MWNTs and higher specific surface area.
Abstract: Most of the commercial gluten free products are
nutritionally inferior when compared to gluten containing
counterparts as manufacturers most often use the refined flours and
starches. So it is possible that people on gluten free diet have low
intake of fibre content. The foxtail millet flour and copra meal are
gluten free and have high fibre and protein contents. The formulation
of fibre rich gluten free cookies was optimized by response surface
methodology considering independent process variables as proportion
of Foxtail millet (Setaria italica) flour in mixed flour, fat content and
guar gum. The sugar, sodium chloride, sodium bicarbonates and
water were added in fixed proportion as 60, 1.0, 0.4 and 20% of
mixed flour weight, respectively. Optimum formulation obtained for
maximum spread ratio, fibre content, surface L-value, overall
acceptability and minimum breaking strength were 80% foxtail millet
flour in mixed flour, 42.8 % fat content and 0.05% guar gum.
Abstract: This paper investigates the development of weld zone
in Resistance Spot Welding (RSW) which focuses on weld nugget and Heat Affected Zone (HAZ). The effects of four factors namely
weld current, weld time, electrode force and hold time were studied using a general 24 factorial design augmented by five centre points. The results of the analysis showed that all selected factors except
hold time exhibit significant effect on weld nugget radius and HAZ size. Optimization of the welding parameters (weld current, weld
time and electrode force) to normalize weld nugget and to minimize
HAZ size was then conducted using Central Composite Design (CCD) in Response Surface Methodology (RSM) and the optimum
parameters were determined. A regression model for radius of weld nugget and HAZ size was developed and its adequacy was evaluated.
The experimental results obtained under optimum operating conditions were then compared with the predicted values and were
found to agree satisfactorily with each other
Abstract: Heat source addition to the axisymmetric supersonic
inlet may improve the performance parameters, which will increase
the inlet efficiency. In this investigation the heat has been added to
the flow field at some distance ahead of an axisymmetric inlet by
adding an imaginary thermal source upstream of cowl lip. The effect
of heat addition on the drag coefficient, mass flow rate and the
overall efficiency of the inlet have been investigated. The results
show that heat addition causes flow separation, hence to prevent this
phenomena, roughness has been added on the spike surface.
However, heat addition reduces the drag coefficient and the inlet
mass flow rate considerably. Furthermore, the effects of position,
size, and shape on the inlet performance were studied. It is found that
the thermal source deflects the flow streamlines. By improper
location of the thermal source, the optimum condition has been
obtained. For the optimum condition, the drag coefficient is
considerably reduced and the inlet mass flow rate and its efficiency
have been increased slightly. The optimum shape of the heat source
is obtained too.
Abstract: A phorbol-12-myristate-13-acetate (TPA) is a synthetic analogue of phorbol ester (PE), a natural toxic compound of Euphorbiaceae plant. The oil extracted from plants of this family is useful source for primarily biofuel. However this oil might also be used as a foodstuff due to its significant nutrition content. The limitations for utilizing the oil as a foodstuff are mainly due to a toxicity of PE. Currently, a majority of PE detoxification processes are expensive as include multi steps alcohol extraction sequence.
Ozone is considered as a strong oxidative agent. It reacts with PE by attacking the carbon-carbon double bond of PE. This modification of PE molecular structure yields a non toxic ester with high lipid content.
This report presents data on development of simple and cheap PE detoxification process with water application as a buffer and ozone as reactive component. The core of this new technique is an application for a new microscale plasma unit to ozone production and the technology permits ozone injection to the water-TPA mixture in form of microbubbles.
The efficacy of a heterogeneous process depends on the diffusion coefficient which can be controlled by contact time and interfacial area. The low velocity of rising microbubbles and high surface to volume ratio allow efficient mass transfer to be achieved during the process. Direct injection of ozone is the most efficient way to process with such highly reactive and short lived chemical.
Data on the plasma unit behavior are presented and the influence of gas oscillation technology on the microbubble production mechanism has been discussed. Data on overall process efficacy for TPA degradation is shown.
Abstract: The present investigation aimed to study the
histomorphometric characterizations of the thyroid gland of the duck.
Five adult male and five adult female ducks were used in the
experiment. Results showed that the overall histological structure of
the thyroid gland of the duck were similar to those of the other
vertebrae. The gland consisted of roughly spherical randomly
distributed micro and macrofollicles with very little interstitial tissue
between them. Each follicle is lined by a single layer of epithelial
cells enclosing a cavity, the follicular cavity, which is filled with
colloid. Ultrastructural findings showed that the apical surface of the
follicular cells bears a variable number of short, irregularly
distributed microvilli which are apparently more numerous on the
columnar cells than on the lower, relatively inactive cells.
Mitochondria and rough endoplasmic reticulum occupy the
subnuclear region of the follicular cell, whereas the Golgi complex,
free ribosomes and colloid droplets were found in the apical
cytoplasm. At light or electron microscopic levels, there was no sex
difference in histomorphometric characteristics of the thyroid
glands.ls.
Abstract: Feeder is one of the airships of the Multibody Advanced Airship for Transport (MAAT) system, under development within the EU FP7 project. MAAT is based on a modular concept composed of two different parts that have the possibility to join; respectively they are the so-called Cruiser and Feeder, designed on the lighter than air principle. Feeder, also named ATEN (Airship Transport Elevator Network), is the smaller one which joins the bigger one, Cruiser, also named PTAH (Photovoltaic modular Transport Airship for High altitude),envisaged to happen at 15km altitude. During the MAAT design phase, the aerodynamic studies of the both airships and their interactions are analyzed. The objective of these studies is to understand the aerodynamic behavior of all the preselected configurations, as an important element in the overall MAAT system design. The most of these configurations are only simulated by CFD, while the most feasible one is experimentally analyzed in order to validate and thrust the CFD predictions. This paper presents the numerical and experimental investigation of the Feeder “conical like" shape configuration. The experiments are focused on the aerodynamic force coefficients and the pressure distribution over the Feeder outer surface, while the numerical simulation cover also the analysis of the velocity and pressure distribution. Finally, the wind tunnel experiment is compared with its CFD model in order to validate such specific simulations with respective experiments and to better understand the difference between the wind tunnel and in-flight circumstances.
Abstract: The present work represents an investigation of the
hydrolysis of hull-less pumpkin (Cucurbita Pepo L.) oil cake protein
isolate (PuOC PI) by pepsin. To examine the effectiveness and
suitability of pepsin towards PuOC PI the kinetic parameters for
pepsin on PuOC PI were determined and then, the hydrolysis process
was studied using Response Surface Methodology (RSM). The
hydrolysis was carried out at temperature of 30°C and pH 3.00. Time
and initial enzyme/substrate ratio (E/S) at three levels were selected
as the independent parameters. The degree of hydrolysis, DH, was
mesuared after 20, 30 and 40 minutes, at initial E/S of 0.7, 1 and 1.3
mA/mg proteins. Since the proposed second-order polynomial model
showed good fit with the experimental data (R2 = 0.9822), the
obtained mathematical model could be used for monitoring the
hydrolysis of PuOC PI by pepsin, under studied experimental
conditions, varying the time and initial E/S. To achieve the highest
value of DH (39.13 %), the obtained optimum conditions for time
and initial E/S were 30 min and 1.024 mA/mg proteins.
Abstract: Response surface methodology (RSM) is a very
efficient tool to provide a good practical insight into developing new
process and optimizing them. This methodology could help
engineers to raise a mathematical model to represent the behavior of
system as a convincing function of process parameters.
Through this paper the sequential nature of the RSM surveyed for process
engineers and its relationship to design of experiments (DOE), regression
analysis and robust design reviewed. The proposed four-step procedure in
two different phases could help system analyst to resolve the parameter
design problem involving responses. In order to check accuracy of the
designed model, residual analysis and prediction error sum of squares
(PRESS) described.
It is believed that the proposed procedure in this study can resolve a
complex parameter design problem with one or more responses. It can be
applied to those areas where there are large data sets and a number of
responses are to be optimized simultaneously. In addition, the proposed
procedure is relatively simple and can be implemented easily by using
ready-made standard statistical packages.
Abstract: Oxygen transfer, the process by which oxygen is
transferred from the gaseous to liquid phase, is a vital part of the
waste water treatment process. Because of low solubility of
oxygen and consequent low rate of oxygen transfer, sufficient
oxygen to meet the requirement of aerobic waste does not enter
through normal surface air water interface. Many theories have
come up in explaining the mechanism of gas transfer and
absorption of non-reacting gases in a liquid, of out of which, Two
film theory is important. An exiting mathematical model
determines approximate value of Overall Gas Transfer coefficient.
The Overall Gas Transfer coefficient, in case of Penetration theory,
is 1.13 time more than that obtained in case of Two film theory.
The difference is due to the difference in assumptions in the two
theories.
The paper aims at development of mathematical model which
determines the value of Overall Gas Transfer coefficient with
greater accuracy than the existing model.
Abstract: In this study, the effect of greywater irrigation on airwater interfacial area is investigated. Several soil column experiments were conducted for different greywater irrigation to develop the pressure-saturation curves. Surface tension was measured for different greywater concentration and fitted for Gibbs adsorption equation. Pressure-saturation curves show that the reduction of capillary rise stops when it reaches its critical micelle concentration (CMC). A simple theory is derived from pressure-saturation curves for calculating air-water interfacial area in porous medium during greywater irrigation by introducing a term 'hydraulic radius' for the pores. This term diminishes any effect of pore shapes on the air-water interfacial area. The air-water interfacial area was calculated using the pressure-saturation curves and found that it decreases with increasing moisture content. But no significant effect was observed on air-water interfacial area for different greywater irrigation. A maximum of 10% variation in interfacial area was observed at the residual saturation zone.
Abstract: The explosive growth of World Wide Web has posed
a challenging problem in extracting relevant data. Traditional web
crawlers focus only on the surface web while the deep web keeps
expanding behind the scene. Deep web pages are created
dynamically as a result of queries posed to specific web databases.
The structure of the deep web pages makes it impossible for
traditional web crawlers to access deep web contents. This paper,
Deep iCrawl, gives a novel and vision-based approach for extracting
data from the deep web. Deep iCrawl splits the process into two
phases. The first phase includes Query analysis and Query translation
and the second covers vision-based extraction of data from the
dynamically created deep web pages. There are several established
approaches for the extraction of deep web pages but the proposed
method aims at overcoming the inherent limitations of the former.
This paper also aims at comparing the data items and presenting them
in the required order.
Abstract: Distance visualization of large datasets often takes the direction of remote viewing and zooming techniques of stored static images. However, the continuous increase in the size of datasets and visualization operation causes insufficient performance with traditional desktop computers. Additionally, the visualization techniques such as Isosurface depend on the available resources of the running machine and the size of datasets. Moreover, the continuous demand for powerful computing powers and continuous increase in the size of datasets results an urgent need for a grid computing infrastructure. However, some issues arise in current grid such as resources availability at the client machines which are not sufficient enough to process large datasets. On top of that, different output devices and different network bandwidth between the visualization pipeline components often result output suitable for one machine and not suitable for another. In this paper we investigate how the grid services could be used to support remote visualization of large datasets and to break the constraint of physical co-location of the resources by applying the grid computing technologies. We show our grid enabled architecture to visualize large medical datasets (circa 5 million polygons) for remote interactive visualization on modest resources clients.
Abstract: Performance control law is studied for an
interconnected fractional nonlinear system. Applying a backstepping
algorithm, a backstepping sliding mode controller (BSMC) is
developed for fractional nonlinear system. To improve control law
performance, BSMC is coupled to an adaptive sliding mode observer
have a filtered error as a sliding surface. The both architecture
performance is studied throughout the inverted pendulum mounted on
a cart. Simulation result show that the BSMC coupled to an adaptive
sliding mode observer have stable control law and eligible control
amplitude than the BSMC.