Abstract: The load frequency control problem of power systems has attracted a lot of attention from engineers and researchers over the years. Increasing and quickly changing load demand, coupled with the inclusion of more generators with high variability (solar and wind power generators) on the network are making power systems more difficult to regulate. Frequency changes are unavoidable but regulatory authorities require that these changes remain within a certain bound. Engineers are required to perform the tricky task of adjusting the control system to maintain the frequency within tolerated bounds. It is well known that to minimize frequency variations, a large proportional feedback gain (speed regulation constant) is desirable. However, this improvement in performance using proportional feedback comes about at the expense of a reduced stability margin and also allows some steady-state error. A conventional PI controller is then included as a secondary control loop to drive the steadystate error to zero. In this paper, we propose a robust controller to replace the conventional PI controller which guarantees performance and stability of the power system over the range of variation of the speed regulation constant. Simulation results are shown to validate the superiority of the proposed approach on a simple single-area power system model.
Abstract: This paper presents a constrained valley detection
algorithm. The intent is to find valleys in the map for the path planning
that enables a robot or a vehicle to move safely. The constraint to the
valley is a desired width and a desired depth to ensure the space for
movement when a vehicle passes through the valley. We propose an
algorithm to find valleys satisfying these 2 dimensional constraints.
The merit of our algorithm is that the pre-processing and the
post-processing are not necessary to eliminate undesired small valleys.
The algorithm is validated through simulation using digitized
elevation data.
Abstract: Efficient handoff algorithms are a cost-effective way
of enhancing the capacity and QoS of cellular system. The higher
value of hysteresis effectively prevents unnecessary handoffs but
causes undesired cell dragging. This undesired cell dragging causes
interference or could lead to dropped calls in microcellular
environment. The problems are further exacerbated by the corner
effect phenomenon which causes the signal level to drop by 20-30 dB
in 10-20 meters. Thus, in order to maintain reliable communication
in a microcellular system new and better handoff algorithms must be
developed. A fuzzy based handoff algorithm is proposed in this paper
as a solution to this problem. Handoff on the basis of ratio of slopes
of normal signal loss to the actual signal loss is presented. The fuzzy
based solution is supported by comparing its results with the results
obtained in analytical solution.
Abstract: Embedded systems need to respect stringent real
time constraints. Various hardware components included in such
systems such as cache memories exhibit variability and therefore
affect execution time. Indeed, a cache memory access from an
embedded microprocessor might result in a cache hit where the
data is available or a cache miss and the data need to be fetched
with an additional delay from an external memory. It is therefore
highly desirable to predict future memory accesses during
execution in order to appropriately prefetch data without incurring
delays. In this paper, we evaluate the potential of several artificial
neural networks for the prediction of instruction memory
addresses. Neural network have the potential to tackle the nonlinear
behavior observed in memory accesses during program
execution and their demonstrated numerous hardware
implementation emphasize this choice over traditional forecasting
techniques for their inclusion in embedded systems. However,
embedded applications execute millions of instructions and
therefore millions of addresses to be predicted. This very
challenging problem of neural network based prediction of large
time series is approached in this paper by evaluating various neural
network architectures based on the recurrent neural network
paradigm with pre-processing based on the Self Organizing Map
(SOM) classification technique.
Abstract: This research aims to create a model for analysis of student motivation behavior on e-Learning based on association rule mining techniques in case of the Information Technology for Communication and Learning Course at Suan Sunandha Rajabhat University. The model was created under association rules, one of the data mining techniques with minimum confidence. The results showed that the student motivation behavior model by using association rule technique can indicate the important variables that influence the student motivation behavior on e-Learning.
Abstract: An Automated Rapid Maxillary Expander (ARME) is
a specially designed microcontroller-based orthodontic appliance to
overcome the shortcomings imposed by the traditional maxillary
expansion appliances. This new device is operates by automatically
widening the maxilla (upper jaw) by expanding the midpalatal suture
[1]. The ARME appliance that has been developed is a combination
of modified butterfly expander appliance, micro gear, micro motor,
and microcontroller to automatically produce light and continuous
pressure to expand the maxilla. For this study, the functionality of the
system is verified through laboratory tests by measure the forced
applied to the teeth each time the maxilla expands. The laboratory
test results show that the developed appliance meets the desired
performance specifications consistently.
Abstract: Panoramic view generation has always offered
novel and distinct challenges in the field of image processing.
Panoramic view generation is nothing but construction of bigger
view mosaic image from set of partial images of the desired view.
The paper presents a solution to one of the problems of image
seascape formation where some of the partial images are color and
others are grayscale. The simplest solution could be to convert all
image parts into grayscale images and fusing them to get grayscale
image panorama. But in the multihued world, obtaining the colored
seascape will always be preferred. This could be achieved by picking
colors from the color parts and squirting them in grayscale parts of
the seascape. So firstly the grayscale image parts should be colored
with help of color image parts and then these parts should be fused to
construct the seascape image.
The problem of coloring grayscale images has no exact solution.
In the proposed technique of panoramic view generation, the job of
transferring color traits from reference color image to grayscale
image is done by palette based method. In this technique, the color
palette is prepared using pixel windows of some degrees taken from
color image parts. Then the grayscale image part is divided into pixel
windows with same degrees. For every window of grayscale image
part the palette is searched and equivalent color values are found,
which could be used to color grayscale window. For palette
preparation we have used RGB color space and Kekre-s LUV color
space. Kekre-s LUV color space gives better quality of coloring. The
searching time through color palette is improved over the exhaustive
search using Kekre-s fast search technique.
After coloring the grayscale image pieces the next job is fusion of
all these pieces to obtain panoramic view. For similarity estimation
between partial images correlation coefficient is used.
Abstract: Natural gas flow contains undesirable solid particles,
liquid condensation, and/or oil droplets and requires reliable
removing equipment to perform filtration. Recent natural gas
processing applications are demanded compactness and reliability of
process equipment. Since conventional means are sophisticated in
design, poor in efficiency, and continue lacking robust, a supersonic
nozzle has been introduced as an alternative means to meet such
demands.
A 3-D Convergent-Divergent Nozzle is simulated using
commercial Code for pressure ratio (NPR) varies from 1.2 to 2. Six
different shapes of nozzle are numerically examined to illustrate the
position of shock-wave as such spot could be considered as a
benchmark of particle separation. Rectangle, triangle, circular,
elliptical, pentagon, and hexagon nozzles are simulated using Fluent
Code with all have same cross-sectional area.
The simple one-dimensional inviscid theory does not describe the
actual features of fluid flow precisely as it ignores the impact of
nozzle configuration on the flow properties. CFD Simulation results,
however, show that nozzle geometry influences the flow structures
including location of shock wave.
The CFD analysis predicts shock appearance when p01/pa>1.2 for
almost all geometry and locates at the lower area ratio (Ae/At).
Simulation results showed that shock wave in Elliptical nozzle has
the farthest distance from the throat among the others at relatively
small NPR. As NPR increases, hexagon would be the farthest. The
numerical result is compared with available experimental data and
has shown good agreement in terms of shock location and flow
structure.
Abstract: State-based testing is frequently used in software testing. Test data generation is one of the key issues in software testing. A properly generated test suite may not only locate the errors in a software system, but also help in reducing the high cost associated with software testing. It is often desired that test data in the form of test sequences within a test suite can be automatically generated to achieve required test coverage. This paper proposes an Ant Colony Optimization approach to test data generation for the state-based software testing.
Abstract: For high-speed control of robots, a good knowledge of system modelling is necessary to obtain the desired bandwidth. In this paper, we present a cartesian robot with a pan/tilt unit in end-effector (5 dof). This robot is implemented with powerful direct drive AC induction machines. The dynamic model, parameter identification and model validation of the robot are studied (including actuators). This work considers the cartesian robot coupled and non linear (contrary to normal considerations for this type of robots). The mechanical and control architecture proposed in this paper is efficient for industrial and research application in which high speed, well known model and very high accuracy are required.
Abstract: Wheeled Mobile Robots (WMRs) are built with their
Wheels- drive machine, Motors. Depend on their desire design of
WMR, Technicians made used of DC Motors for motion control. In
this paper, the author would like to analyze how to choose DC motor
to be balance with their applications of especially for WMR.
Specification of DC Motor that can be used with desire WMR is to
be determined by using MATLAB Simulink model. Therefore, this
paper is mainly focus on software application of MATLAB and
Control Technology. As the driving system of DC motor, a
Peripheral Interface Controller (PIC) based control system is
designed including the assembly software technology and H-bridge
control circuit. This Driving system is used to drive two DC gear
motors which are used to control the motion of WMR. In this
analyzing process, the author mainly focus the drive system on
driving two DC gear motors that will control with Differential Drive
technique to the Wheeled Mobile Robot . For the design analysis of
Motor Driving System, PIC16F84A is used and five inputs of sensors
detected data are tested with five ON/OFF switches. The outputs of
PIC are the commands to drive two DC gear motors, inputs of Hbridge
circuit .In this paper, Control techniques of PIC
microcontroller and H-bridge circuit, Mechanism assignments of
WMR are combined and analyzed by mainly focusing with the
“Modeling and Simulink of DC Motor using MATLAB".
Abstract: In this paper the reference current for Voltage Source
Converter (VSC) of the Shunt Active Power Filter (SAPF) is
generated using Synchronous Reference Frame method,
incorporating the PI controller with anti-windup scheme. The
proposed method improves the harmonic filtering by compensating
the winding up phenomenon caused by the integral term of the PI
controller.
Using Reference Frame Transformation, the current is transformed
from om a - b - c stationery frame to rotating 0 - d - q frame. Using
the PI controller, the current in the 0 - d - q frame is controlled to
get the desired reference signal. A controller with integral action
combined with an actuator that becomes saturated can give some
undesirable effects. If the control error is so large that the integrator
saturates the actuator, the feedback path becomes ineffective because
the actuator will remain saturated even if the process output changes.
The integrator being an unstable system may then integrate to a very
large value, the phenomenon known as integrator windup.
Implementing the integrator anti-windup circuit turns off the
integrator action when the actuator saturates, hence improving the
performance of the SAPF and dynamically compensating harmonics
in the power network. In this paper the system performance is
examined with Shunt Active Power Filter simulation model.
Abstract: Due to growing environmental concerns of the cement
industry, alternative cement technologies have become an area of
increasing interest. It is now believed that new binders are
indispensable for enhanced environmental and durability
performance. Self-compacting Geopolymer concrete is an innovative
method and improved way of concreting operation that does not
require vibration for placing it and is produced by complete
elimination of ordinary Portland cement.
This paper documents the assessment of the compressive strength
and workability characteristics of low-calcium fly ash based selfcompacting
geopolymer concrete. The essential workability
properties of the freshly prepared Self-compacting Geopolymer
concrete such as filling ability, passing ability and segregation
resistance were evaluated by using Slump flow, V-funnel, L-box and
J-ring test methods. The fundamental requirements of high
flowability and segregation resistance as specified by guidelines on
Self Compacting Concrete by EFNARC were satisfied. In addition,
compressive strength was determined and the test results are included
here. This paper also reports the effect of extra water, curing time and
curing temperature on the compressive strength of self-compacting
geopolymer concrete. The test results show that extra water in the
concrete mix plays a significant role. Also, longer curing time and
curing the concrete specimens at higher temperatures will result in
higher compressive strength.
Abstract: A general purpose viscous flow solver Ansys CFX
was used to solve the unsteady three-dimensional (3D) Reynolds
Averaged Navier-Stokes Equation (RANSE) for simulating a 3D
numerical viscous wave tank. A flap-type wave generator was
incorporated in the computational domain to generate the desired
incident waves. Authors have made effort to study the physical
behaviors of Flap type wave maker with governing parameters.
Dependency of the water fill depth, Time period of oscillations and
amplitude of oscillations of flap were studied. Effort has been made
to establish relations between parameters. A validation study was
also carried out against CFD methodology with wave maker theory.
It has been observed that CFD results are in good agreement with
theoretical results. Beaches of different slopes were introduced to
damp the wave, so that it should not cause any reflection from
boundary. As a conclusion this methodology can simulate the
experimental wave-maker for regular wave generation for different
wave length and amplitudes.
Abstract: Machine Translation (MT 3) of English text to its Urdu equivalent is a difficult challenge. Lot of attempts has been made, but a few limited solutions are provided till now. We present a direct approach, using an expert system to translate English text into its equivalent Urdu, using The Unicode Standard, Version 4.0 (ISBN 0-321-18578-1) Range: 0600–06FF. The expert system works with a knowledge base that contains grammatical patterns of English and Urdu, as well as a tense and gender-aware dictionary of Urdu words (with their English equivalents).
Abstract: Analyse of locally manufactured Low Density Polyethylene (LDPE) durability, used within lining systems at bottom of Municipal Solid Waste (landfill), is done in the present work. For this end, short and middle time creep behavior under tension of the analyzed material is carried out. The locally manufactured material is tested and compared to the European one (LDPE-CE). Both materials was tested in 03 various mediums: ambient and two aggressive (salty water and foam water), using three specimens in each case. A testing campaign is carried out using an especially designed and achieved testing bench. Moreover, characterisation tests were carried out to evaluate the medium effect on the mechanical properties of the tested material (LDPE). Furthermore, experimental results have been used to establish a law regression which can be used to predict creep behaviour of the analyzed material. As a result, the analyzed LDPE material has showed a good stability in different ambient and aggressive mediums; as well, locally manufactured LDPE seems more flexible, compared with the European one. This makes it more useful to the desired application.
Abstract: Grid computing is growing rapidly in the distributed
heterogeneous systems for utilizing and sharing large-scale resources
to solve complex scientific problems. Scheduling is the most recent
topic used to achieve high performance in grid environments. It aims
to find a suitable allocation of resources for each job. A typical
problem which arises during this task is the decision of scheduling. It
is about an effective utilization of processor to minimize tardiness
time of a job, when it is being scheduled. This paper, therefore,
addresses the problem by developing a general framework of grid
scheduling using dynamic information and an ant colony
optimization algorithm to improve the decision of scheduling. The
performance of various dispatching rules such as First Come First
Served (FCFS), Earliest Due Date (EDD), Earliest Release Date
(ERD), and an Ant Colony Optimization (ACO) are compared.
Moreover, the benefit of using an Ant Colony Optimization for
performance improvement of the grid Scheduling is also discussed. It
is found that the scheduling system using an Ant Colony
Optimization algorithm can efficiently and effectively allocate jobs
to proper resources.
Abstract: Cameras are often mounted on platforms that canmove like rovers, booms, gantries and aircraft. People operate suchplatforms to capture desired views of scene or target. To avoidcollisions with the environment and occlusions, such platforms oftenpossess redundant degrees-of-freedom. As a result, manipulatingsuch platforms demands much skill. Visual-servoing some degrees-of-freedom may reduce operator burden and improve tracking per-formance. This concept, which we call human-in-the-loop visual-servoing, is demonstrated in this paper and applies a Α-β-γ filter and feedforward controller to a broadcast camera boom.
Abstract: The purpose of this paper is to introduce an interactive online case-study library website developed in a national project. The design goal of the website is to provide interactive, enhanced, case-based and online educational resource for educators through the purpose and within the scope of a national project. The ADDIE instructional design model was used in the development of the website for interactive case-based library. This library is developed on a web-based platform, which is important in terms of manageability, accessibility, and updateability of data. Users are able to sort the displayed case-studies by their titles, dates, ratings, view counts, etc. The usability test is used and the expert opinion is taken for the evaluation of the website. This website is a tool to integrate technology into education. It is believed that this website will be beneficial for pre-service and in-service teachers in terms of their professional developments.
Abstract: This paper describes a novel monitoring scheme to
minimize total active power in digital circuits depend on the demand
frequency, by adjusting automatically both supply voltage and
threshold voltages based on circuit operating conditions such as
temperature, process variations, and desirable frequency. The delay
monitoring results, will be control and apply so as to be maintained at
the minimum value at which the chip is able to operate for a given
clock frequency. Design details of power monitor are examined using
simulation framework in 32nm BTPM model CMOS process.
Experimental results show the overhead of proposed circuit in terms
of its power consumption is about 40 μW for 32nm technology;
moreover the results show that our proposed circuit design is not far
sensitive to the temperature variations and also process variations.
Besides, uses the simple blocks which offer good sensitivity, high
speed, the continuously feedback loop. This design provides up to
40% reduction in power consumption in active mode.