Abstract: The acidity of different raw Jordanian clays
containing zeolite, bentonite, red and white kaolinite and diatomite
was characterized by means of temperature programmed desorption
(TPD) of ammonia, conversion of 2-methyl-3-butyn-2-ol (MBOH),
FTIR and BET-measurements. FTIR spectra proved presence of
silanol and bridged hydroxyls on the clay surface. The number of
acidic sites was calculated from experimental TPD-profiles. We
observed the decrease of surface acidity correlates with the decrease
of Si/Al ratio except for diatomite. On the TPD-plot for zeolite two
maxima were registered due to different strength of surface acidic
sites. Values of MBOH conversion, product yields and selectivity
were calculated for the catalysis on Jordanian clays. We obtained that
all clay samples are able to convert MBOH into a major product
which is 3-methyl-3-buten-1-yne (MBYNE) catalyzed by acid
surface sites with the selectivity close to 70%. There was found a
correlation between MBOH conversion and acidity of clays
determined by TPD-NH3, i.e. the higher the acidity the higher the
conversion of MBOH. However, diatomite provided the lowest
conversion of MBOH as result of poor polarization of silanol groups.
Comparison of surface areas and conversions revealed the highest
density of active sites for red kaolinite and the lowest for zeolite and
diatomite.
Abstract: The mathematical framework for studying of a fuzzy approximate reasoning is presented in this paper. Two important defuzzification methods (Area defuzzification and Height defuzzification) besides the center of gravity method which is the best well known defuzzification method are described. The continuity of the defuzzification methods and its application to a fuzzy feedback control are discussed.
Abstract: This paper studies the application of a variety of
sawdust materials in the production of lightweight insulating bricks.
First, the mineralogical and chemical composition of clays was determined. Next, ceramic bricks were fabricated with different
quantities of materials (3–6 and 9 wt. % for sawdust, 65 wt. % for grey clay, 24–27 and 30 wt. % for yellow clay and 2 wt% of tuff).
These bricks were fired at 800 and 950 °C. The effect of adding this sawdust on the technological behaviour of the brick was assessed by
drying and firing shrinkage, water absorption, porosity, bulk density
and compressive strength. The results have shown that the optimum
sintering temperature is 950 °C. Below this temperature, at 950 °C,
increased open porosity was observed, which decreased the compressive strength of the bricks. Based on the results obtained, the
optimum amounts of waste were 9 wt. % sawdust of eucalyptus, 24 wt. % shaping moisture and 1.6 particle size diameter. These percentages produced bricks whose mechanical properties were
suitable for use as secondary raw materials in ceramic brick
production.
Abstract: A novel physico-chemical route to produce few layer graphene nanoribbons with atomically smooth edges is reported, via acid treatment (H2SO4:HNO3) followed by characteristic thermal shock processes involving extremely cold substances. Samples were studied by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Raman spectroscopy and X-ray photoelectron spectroscopy. This method demonstrates the importance of having the nanotubes open ended for an efficient uniform unzipping along the nanotube axis. The average dimensions of these nanoribbons are approximately ca. 210 nm wide and consist of few layers, as observed by transmission electron microscopy. The produced nanoribbons exhibit different chiralities, as observed by high resolution transmission electron microscopy. This method is able to provide graphene nanoribbons with atomically smooth edges which could be used in various applications including sensors, gas adsorption materials, composite fillers, among others.
Abstract: Sugarcane bagasses are one of the most extensively used agricultural residues. Using acid hydrolysis and fermentation, conversion of sugarcane bagasses to lactic acid was technically and economically feasible. This research was concerned with the solubility of lignin in ammonium hydroxide, acid hydrolysis and lactic acid fermentation by Lactococcus lactis, Lactobacillus delbrueckii, Lactobacillus plantarum, and Lactobacillus casei. The lignin extraction results for different ammonium hydroxide concentrations showed that 10 % (v/v) NH4OH was favorable to lignin dissolution. Acid hydrolysis can be enhanced with increasing acid concentration and reaction temperature. The optimum glucose and xylose concentrations occurred at 121 ○C for 1 hour hydrolysis time in 10% sulphuric acid solution were 32 and 11 g/l, respectively. In order to investigate the significance of medium composition on lactic acid production, experiments were undertaken whereby a culture of Lactococcus lactis was grown under various glucose, peptone, yeast extract and xylose concentrations. The optimum medium was composed of 5 g/l glucose, 2.5 g/l xylose, 10 g/l peptone and 5 g/l yeast extract. Lactococcus lactis represents the most efficient for lactic acid production amongst those considered. The lactic acid fermentation by Lactococcus lactis after 72 hours gave the highest yield of 1.4 (g lactic acid per g reducing sugar).
Abstract: The Philosophy of Sufficiency Economy, bestowed
by His Majesty the King Bhumibol Adulyadej to the people of
Thailand, highlights a balanced way of living. Three principles of
moderation reasonableness, and immunity, along with the conditions
for morality and knowledge, can be applied to any level of the
society–from an individual to the nation. The Philosophy of
Sufficiency Economy helps address the current development
challenges, which are issues on institutions, environmental
sustainability, human well-being, and the role of the government.
Abstract: Megalopolis is a group of densely populated metropolitan areas that combine to form an urban complex. Since China introduced the economic reforms in late 1970s, the Chinese urban system has experienced unprecedented growth. The process of urbanisation prevailed in the 1980s, and the process of predominantly large city growth appeared to continue through 1990s and 2000s. In this study, the magnitude and pattern of urbanisation in China during 1990s were examined using remotely sensed imagery acquired by TM/ETM+ sensor onboard the Landsat satellites. The development of megalopolis areas in China was also studied based on the GIS analysis of the increases of urban and built-up area from 1990 to 2000. The analysis suggests that in the traditional agricultural zones in China, e.g., Huang-Huai-Hai Plains, Changjiang River Delta, Pearl River Delta and Sichuan Basin, the urban and built-up areas increased by 1.76 million hectares, of which 0.82 million hectares are expansion of urban areas, an increase of 24.78% compared with 1990 at the national scale. The Yellow River Delta, Changjiang River Delta and Pearl River Delta also saw an increase of urban and built-up area by 63.9%, 66.2% and 83.0% respectively. As a result, three major megalopolises were developed in China: the Guangzhou-Shenzhen-Hong Kong- Macau (Pearl River Delta: PRD) megalopolis area, the Shanghai- Nanjing-Hangzhou (Changjiang River Delta: CRD) megalopolis area and the Beijing-Tianjing-Tangshan-Qinhuangdao (Yellow River Delta-Bohai Sea Ring: YRD) megalopolis area. The relationship between the processed of megalopolisation and the inter-provincial population flow was also explored in the context of social-economic and transport infrastructure development in Post-reform China.
Abstract: This article addresses the procedures to validate the Arabic version of Multiple Intelligence Development Assessment Scale (MIDAS). The content validity was examined based on the experts- judgments on the MIDAS-s items in the Arabic version. The content of eleven items in the Arabic version of MIDAS was modified to match the Arabic context. Then a translation from original English version of MIDAS into Arabic language was performed. The reliability of the Arabic MIDAS was calculated based on test and retest method and found to be 0.85 for the overall MIDAS and for the different subscales ranging between 0.78 - 0.87. The examination of construct validity for the overall Arabic MIDAS and its subscales was established by using Winsteps program version 6 based on Rasch model in order to fit the items into the Arabic context. The findings indicated that, the eight subscales in Arabic version of MIDAS scale have a unidimensionality, and the total number of kept items in the overall scale is 108 items.
Abstract: Large full frequency band gaps of surface and bulk
acoustic waves in two-dimensional phononic band structures with
hollow cylinders are addressed in this paper. It is well-known that
absolute frequency band gaps are difficultly obtained in a band
structure consisted of low-acoustic-impedance cylinders in
high-acoustic-impedance host materials such as PMMA/Ni band
structures. Phononic band structures with hollow cylinders are
analyzed and discussed to obtain large full frequency band gaps not
only for bulk modes but also for surface modes. The tendency of
absolute frequency band gaps of surface and bulk acoustic waves is
also addressed by changing the inner radius of hollow cylinders in this
paper. The technique and this kind of band structure are useful for
tuning the frequency band gaps and the design of acoustic waveguides.
Abstract: The study aimed to identify the nature of autistic
talent, the manifestations of their weak central coherence, and their
sensory characteristics. The case study consisted of four talented
autistic males. Two of them in drawing, one in clay formation and
one in jigsaw puzzle. Tools of data collection were Group Embedded
Figures Test, Block Design Test, Sensory Profile Checklist Revised,
Interview forms and direct observation. Results indicated that talent
among autistics emerges in limited domain and being extraordinary
for each case. Also overlapping construction properties. Indeed, they
show three perceptual aspects of weak central coherence: The weak
in visual spatial-constructional coherence, the weak in perceptual
coherence and the weak in verbal – semantic coherence. Moreover,
the majority of the study cases used the three strategies of weak
central coherence (segmentation, obliqueness and rotation). As for
the sensory characteristics, all study cases have numbers of that
characteristics that especially emerges in the visual system.
Abstract: This paper deals with dynamic load balancing using PVM. In distributed environment Load Balancing and Heterogeneity are very critical issues and needed to drill down in order to achieve the optimal results and efficiency. Various techniques are being used in order to distribute the load dynamically among different nodes and to deal with heterogeneity. These techniques are using different approaches where Process Migration is basic concept with different optimal flavors. But Process Migration is not an easy job, it impose lot of burden and processing effort in order to track each process in nodes. We will propose a dynamic load balancing technique in which application will intelligently balance the load among different nodes, resulting in efficient use of system and have no overheads of process migration. It would also provide a simple solution to problem of load balancing in heterogeneous environment.
Abstract: Although a picture can be automatically a graphic
work, but especially in the field of graphics and images based on the
idea of advertising and graphic design will be prepared and
photographers to realize the design using his own knowledge and
skills to help does. It is evident that knowledge of photography,
photographer and designer of the facilities, fields of reaching a
higher level of quality offers. At the same time do not have a graphic
designer is also skilled photographer, but can execute your idea may
delegate to an expert photographer. Using technology and methods in
all fields of photography, graphic art may be applicable. But most of
its application in Iran, in works such as packaging, posters, Bill
Board, advertising, brochures and catalogs are. In this study, we
review how the images and techniques in the chart should be used in
Iranian graphic photo what impact has left. Using photography
techniques and procedures can be designed and helped advance the
goals graphic. Technique could not determine the idea. But what is
important to think about design and photography and his creativity
can flourish as a tool to be effective graphic designer in mind.
Computer software to help it's very promotes creativity techniques
shall graphic designer but also it is as a tool. Using images in various
fields, especially graphic arts and only because it is not being
documented, but applications are beautiful. As to his photographic
style from today is graphics. Graphic works try to affect impacts on
their audience. Hence the photo as an important factor is attention.
The other hand saw the man with the extent of forgiving and
understanding people's image, instead of using the word to your files,
allows large messages and concepts should be sent in the shortest
time. Posters, advertisements, brochures, catalog and packaging
products very diverse agricultural, industrial and food could not be
self-image. Today, the use of graphic images for a big score and the
photos to richen the role graphic design plays a major.
Abstract: This paper proposes an application of the differential
evolution (DE) algorithm for solving the economic dispatch problem
(ED). Furthermore, the regenerating population procedure added to
the conventional DE in order to improve escaping the local minimum
solution. To test performance of DE algorithm, three thermal
generating units with valve-point loading effects is used for testing.
Moreover, investigating the DE parameters is presented. The
simulation results show that the DE algorithm, which had been
adjusted parameters, is better convergent time than other optimization
methods.
Abstract: The composite materials were prepared by sawdust, cassava starch and natural rubber latex (NR). The mixtures of 15%w/v gelatinized cassava starch and 15%w/v PVOH were used as the binder of these composite materials. The concentrated rubber latex was added to the mixtures. They were mixed rigorously to the treated sawdust in the ratio of 70:30 until achive uniform dispersion. The batters were subjected to the hot compression moulding at the temperature of 160°C and 3,000 psi pressure for 5 min. The experimental results showed that the mechanical properties of composite materials, which contained the gelatinized cassava starch and PVOH in the ratio of 2:1, 20% NR latex by weight of the dry starch and treated sawdust with 5%NaOH or 1% BPO, were the best. It contributed the maximal compression strength (341.10 + 26.11 N), puncture resistance (8.79 + 0.98 N/mm2) and flexural strength (3.99 + 0.72N/mm2). It is also found that the physicochemical and mechanical properties of composites strongly depends on the interface quality of sawdust, cassava starch and NR latex.
Abstract: There are two common types of operational research techniques, optimisation and metaheuristic methods. The latter may be defined as a sequential process that intelligently performs the exploration and exploitation adopted by natural intelligence and strong inspiration to form several iterative searches. An aim is to effectively determine near optimal solutions in a solution space. In this work, a type of metaheuristics called Ant Colonies Optimisation, ACO, inspired by a foraging behaviour of ants was adapted to find optimal solutions of eight non-linear continuous mathematical models. Under a consideration of a solution space in a specified region on each model, sub-solutions may contain global or multiple local optimum. Moreover, the algorithm has several common parameters; number of ants, moves, and iterations, which act as the algorithm-s driver. A series of computational experiments for initialising parameters were conducted through methods of Rigid Simplex, RS, and Modified Simplex, MSM. Experimental results were analysed in terms of the best so far solutions, mean and standard deviation. Finally, they stated a recommendation of proper level settings of ACO parameters for all eight functions. These parameter settings can be applied as a guideline for future uses of ACO. This is to promote an ease of use of ACO in real industrial processes. It was found that the results obtained from MSM were pretty similar to those gained from RS. However, if these results with noise standard deviations of 1 and 3 are compared, MSM will reach optimal solutions more efficiently than RS, in terms of speed of convergence.
Abstract: There has been a growing interest in utilizing surfactants in remediation processes to separate the hydrophobic volatile organic compounds (HVOCs) from aqueous solution. One attractive process is cloud point extraction (CPE), which utilizes nonionic surfactants as a separating agent. Since the surfactant cost is a key determination of the economic viability of the process, it is important that the surfactants are recycled and reused. This work aims to study the performance of the co-current vacuum stripping using a packed column for HVOCs removal from contaminated surfactant solution. Six types HVOCs are selected as contaminants. The studied surfactant is the branched secondary alcohol ethoxylates (AEs), Tergitol TMN-6 (C14H30O2). The volatility and the solubility of HVOCs in surfactant system are determined in terms of an apparent Henry’s law constant and a solubilization constant, respectively. Moreover, the HVOCs removal efficiency of vacuum stripping column is assessed in terms of percentage of HVOCs removal and the overall liquid phase volumetric mass transfer coefficient. The apparent Henry’s law constant of benzenz , toluene, and ethyl benzene were 7.00×10-5, 5.38×10-5, 3.35× 10-5 respectively. The solubilization constant of benzene, toluene, and ethyl benzene were 1.71, 2.68, 7.54 respectively. The HVOCs removal for all solute were around 90 percent.
Abstract: The study aims to develop a framework of social
network management to enhance customer relationship. Social
network management of this research is derived from social network
site management, individual and organization social network usage
motivation. The survey was conducted with organization employees
who have used social network to interact with customers. The results
reveal that content, link, privacy and security, page design and
interactivity are the major issues of social network site management.
Content, link, privacy and security, individual and organization
motivation have major impacts on encouraging business knowledge
sharing among employees. Moreover, Page design and interactivity,
content, organization motivation and knowledge sharing can improve
customer relationships.
Abstract: Composite nanostructures of metal
core/semiconductor shell (Au/CdS) configuration were prepared
using organometalic method. UV-Vis spectra for the Au/CdS colloids
show initially two well separated bands, corresponding to surface
plasmon of the Au core, and the exciton of CdS shell. The absorption
of CdS shell is enhanced, while the Au plasmon band is suppressed
as the shell thickness increases. The shell sizes were estimated from
the optical spectra using the effective mass approximation model
(EMA), and compared to the sizes of the Au core and CdS shell
measured by high resolution transmission electron microscope
(HRTEM). The changes in the absorption features are discussed in
terms of gradual increase in the coupling strength of the Au core
surface plasmon and the exciton in the CdS. leading to charge
transfer and modification of electron oscillation in Au core.
Abstract: Atrazine, a herbicide widely used in sugarcane and corn production, is a frequently detected groundwater contaminant. An atrazine-degrading bacterium, strain KB02, was obtained from long-term atrazine-treated sugarcane field soils in Kanchanaburi province of Thailand. Strain KB02 had a rod-to-coccus morphological cycle during growth. Sequence analysis of the PCR product indicated that the 16S rRNA gene in strain KB02 was ranging from 97-98% identical to the same region in Klebsiella sp. Based on biochemical, physiological analysis and 16S rDNA sequence analysis of one representative isolate, strain KB02, the isolates belong to the genus Klebsiella in the family Enterobacteriaceae. Interestingly that the various primers for atzA, B and C failed to amplify genomic DNA of strain KB02. Whereas the expected PCR product of atzA, B and C were obtained from the reference strain, Arthrobacter sp. strain KU001.
Abstract: This paper proposes an improved approach based on
conventional particle swarm optimization (PSO) for solving an
economic dispatch(ED) problem with considering the generator
constraints. The mutation operators of the differential evolution (DE)
are used for improving diversity exploration of PSO, which called
particle swarm optimization with mutation operators (PSOM). The
mutation operators are activated if velocity values of PSO nearly to
zero or violated from the boundaries. Four scenarios of mutation
operators are implemented for PSOM. The simulation results of all
scenarios of the PSOM outperform over the PSO and other existing
approaches which appeared in literatures.