Abstract: Among the various cooling processes in industrial
applications such as: electronic devices, heat exchangers, gas
turbines, etc. Gas turbine blades cooling is the most challenging one.
One of the most common practices is using ribbed wall because of
the boundary layer excitation and therefore making the ultimate
cooling. Vortex formation between rib and channel wall will result in
a complicated behavior of flow regime. At the other hand, selecting
the most efficient method for capturing the best results comparing to
experimental works would be a fascinating issue. In this paper 4
common methods in turbulence modeling: standard k-e, rationalized
k-e with enhanced wall boundary layer treatment, k-w and RSM
(Reynolds stress model) are employed to a square ribbed channel to
investigate the separation and thermal behavior of the flow in the
channel. Finally all results from different methods which are used in
this paper will be compared with experimental data available in
literature to ensure the numerical method accuracy.
Abstract: A numerical study is made of laminar, unsteady flow
behind a rotationally oscillating circular cylinder using a recently
developed higher order compact (HOC) scheme. The stream function
vorticity formulation of Navier-Stokes (N-S) equations in cylindrical
polar coordinates are considered as the governing equations. The
temporal behaviour of vortex formation and relevant streamline
patterns of the flow are scrutinized over broad ranges of two
externally specified parameters namely dimensionless forced
oscillating frequency Sf and dimensionless peak rotation rate αm for
the Reynolds-s number Re = 200. Excellent agreements are found
both qualitatively and quantitatively with the existing experimental
and standard numerical results.
Abstract: The development of biomimetic micro-aerial-vehicles
(MAVs) with flapping wings is the future trend in military/domestic
field. The successful flight of MAVs is strongly related to the
understanding of unsteady aerodynamic performance of low Reynolds
number airfoils under dynamic flapping motion. This study explored
the effects of flapping frequency, stroke amplitude, and the inclined
angle of stroke plane on lift force and thrust force of a bio-inspiration
corrugated airfoil with 33 full factorial design of experiment and
ANOVA analysis. Unsteady vorticity flows over a corrugated thin
airfoil executing flapping motion are computed with time-dependent
two-dimensional laminar incompressible Reynolds-averaged
Navier-Stokes equations with the conformal hybrid mesh. The tested
freestream Reynolds number based on the chord length of airfoil as
characteristic length is fixed of 103. The dynamic mesh technique is
applied to model the flapping motion of a corrugated airfoil. Instant
vorticity contours over a complete flapping cycle clearly reveals the
flow mechanisms for lift force generation are dynamic stall, rotational
circulation, and wake capture. The thrust force is produced as the
leading edge vortex shedding from the trailing edge of airfoil to form a
reverse von Karman vortex. Results also indicated that the inclined
angle is the most significant factor on both the lift force and thrust
force. There are strong interactions between tested factors which mean
an optimization study on parameters should be conducted in further
runs.
Abstract: The stability characteristics of water lubricated journal bearings having three axial grooves are obtained theoretically. In this lubricant (water) is fed under pressure from one end of the bearing, through the 3-axial grooves (groove angles may vary). These bearings can use the process fluid as the lubricant, as in the case of feed water pumps. The Reynolds equation is solved numerically by the finite difference method satisfying the boundary conditions. The stiffness and damping coefficient for various bearing number and eccentricity ratios, assuming linear pressure drop along the groove, shows that smaller groove angles better results.
Abstract: Studies on gas solid mass transfer using Supercritical fluid CO2 (SC-CO2) in a packed bed of palm kernels was investigated at operating conditions of temperature 50 °C and 70 °C and pressures ranges from 27.6 MPa, 34.5 MPa, 41.4 MPa and 48.3 MPa. The development of mass transfer models requires knowledge of three properties: the diffusion coefficient of the solute, the viscosity and density of the Supercritical fluids (SCF). Matematical model with respect to the dimensionless number of Sherwood (Sh), Schmidt (Sc) and Reynolds (Re) was developed. It was found that the model developed was found to be in good agreement with the experimental data within the system studied.
Abstract: Numerical analysis of flow characteristics and
separation efficiency in a high-efficiency cyclone has been performed.
Several models based on the experimental observation for a design
purpose were proposed. However, the model is only estimated the
cyclone's performance under the limited environments; it is difficult to
obtain a general model for all types of cyclones. The purpose of this
study is to find out the flow characteristics and separation efficiency
numerically. The Reynolds stress model (RSM) was employed instead
of a standard k-ε or a k-ω model which was suitable for isotropic
turbulence and it could predict the pressure drop and the Rankine
vortex very well. For small particles, there were three significant
components (entrance of vortex finder, cone, and dust collector) for
the particle separation. In the present work, the particle re-entraining
phenomenon from the dust collector to the cyclone body was observed
after considerable time. This re-entrainment degraded the separation
efficiency and was one of the significant factors for the separation
efficiency of the cyclone.
Abstract: This study experimentally investigates the heat transfer effects of forced convection and natural convection under different substrate openings design. A computational fluid dynamics (CFD) model was established and implemented to verify and explain the experimental results and heat transfer behavior. It is found that different opening position will destroy the growth of the boundary layer on substrates to alter the cooling ability for both forced under low Reynolds number and natural convection. Nevertheless, having too many opening may reduce heat conduction and affect the overall heat transfer performance. This study provides future researchers with a guideline on designing and electronic package manufacturing.
Abstract: The major focus of this work was to characterize hydrodynamics in a packed-bed with and without static mixer by using Computational Fluid Dynamic (CFD). The commercial software: COMSOL MULTIPHYSICSTM Version 3.3 was used to simulate flow fields of mixed-gas reactants i.e. CO and H2. The packed-bed was a single tube with the inside diameter of 0.8 cm and the length of 1.2 cm. The static mixer was inserted inside the tube. The number of twisting elements was 1 with 0.8 cm in diameter and 1.2 cm in length. The packed-bed with and without static mixer were both packed with approximately 700 spherical structures representing catalyst pellets. Incompressible Navier-Stokes equations were used to model the gas flow inside the beds at steady state condition, in which the inlet Reynolds Number (Re) was 2.31. The results revealed that, with the insertion of static mixer, the gas was forced to flow radially inward and outward between the central portion of the tube and the tube wall. This could help improving the overall performance of the packed-bed, which could be utilized for heterogeneous catalytic reaction such as reforming and Fischer- Tropsch reactions.
Abstract: The RANS method with Saffman-s turbulence model
was employed to solve the time-dependent turbulent Navier-Stokes
and energy equations for oscillating pipe flows. The method of
partial sums of the Fourier series is used to analyze the harmonic
velocity and temperature results. The complete structures of the
oscillating pipe flows and the averaged Nusselt numbers on the tube
wall are provided by numerical simulation over wide ranges of ReA
and ReR. Present numerical code is validated by comparing the
laminar flow results to analytic solutions and turbulence flow results
to published experimental data at lower and higher Reynolds
numbers respectively. The effects of ReA and ReR on the velocity,
temperature and Nusselt number distributions have been di scussed.
The enhancement of the heat transfer due to oscillating flows has
also been presented. By the way of analyzing the overall Nusselt
number over wide ranges of the Reynolds number Re and Keulegan-
Carpenter number KC, the optimal ratio of the tube diameter over
the oscillation amplitude is obtained based on the existence of a
nearly constant optimal KC number. The potential application of the
present results in sea water cooling has also been discussed.
Abstract: In this manuscript, the LBM is applied for simulating of Mixed Convection in a Lid-Driven cavity with an open side. The cavity horizontal walls are insulated while the west Lid-driven wall is maintained at a uniform temperature higher than the ambient. Prandtl number (Pr) is fixed to 0.71 (air) while Reynolds number (Re) , Richardson number (Ri) and aspect ratio (A) of the cavity are changed in the range of 50-150 , of 0.1-10 and of 1-4 , respectively. The numerical code is validated for the standard square cavity, and then the results of an open ended cavity are presented. Result shows by increasing of aspect ratio, the average Nusselt number (Nu) on lid- driven wall decreases and with same Reynolds number (Re) by increasing of aspect ratio (A), Richardson number plays more important role in heat transfer rate.
Abstract: Linear stochastic estimation and quadratic stochastic
estimation techniques were applied to estimate the entire velocity
flow-field of an open cavity with a length to depth ratio of 2. The
estimations were done through the use of instantaneous velocity
magnitude as estimators. These measurements were obtained by
Particle Image Velocimetry. The predicted flow was compared
against the original flow-field in terms of the Reynolds stresses and
turbulent kinetic energy. Quadratic stochastic estimation proved to be
more superior than linear stochastic estimation in resolving the shear
layer flow. When the velocity fluctuations were scaled up in the
quadratic estimate, both the time-averaged quantities and the
instantaneous cavity flow can be predicted to a rather accurate extent.
Abstract: In this study the mixed convection heat transfer in a
coil-in-shell heat exchanger for various Reynolds numbers and
various dimensionless coil pitch was experimentally investigated.
The experiments were conducted for both laminar and turbulent flow
inside coil and the effects of coil pitch on shell-side heat transfer
coefficient of the heat exchanger were studied. The particular
difference in this study in comparison with the other similar studies
was the boundary conditions for the helical coils. The results indicate
that with the increase of coil pitch, shell-side heat transfer coefficient
is increased.
Abstract: Turbulent forced convection flow in a 2-dimensional channel over periodic grooves is numerically investigated. Finite volume method is used to study the effect of turbulence model. The range of Reynolds number varied from 10000 to 30000 for the ribheight to channel-height ratio (B/H) of 2. The downstream wall is heated by a uniform heat flux while the upstream wall is insulated. The investigation is analyzed with different types of nanoparticles such as SiO2, Al2O3, and ZnO, with water as a base fluid are used. The volume fraction is varied from 1% to 4% and the nanoparticle diameter is utilized between 20nm to 50nm. The results revealed 114% heat transfer enhancement compared to the water in a grooved channel by using SiO2 nanoparticle with volume fraction and nanoparticle diameter of 4% and 20nm respectively.
Abstract: Numerical calculations of flow around a square cylinder are presented using the multi-relaxation-time lattice Boltzmann method at Reynolds number 150. The effects of upstream locations, downstream locations and blockage are investigated systematically. A detail analysis are given in terms of time-trace analysis of drag and lift coefficients, power spectra analysis of lift coefficient, vorticity contours visualizations and phase diagrams. A number of physical quantities mean drag coefficient, drag coefficient, Strouhal number and root-mean-square values of drag and lift coefficients are calculated and compared with the well resolved experimental data and numerical results available in open literature. The results had shown that the upstream, downstream and height of the computational domain are at least 7.5, 37.5 and 12 diameters of the cylinder, respectively.
Abstract: In this study, a semi-cylinder obstacle placed in a
channel is handled to determine the effect of flow and heat transfer
around the obstacle. Both faces of the semi-cylinder are used in the
numerical analysis. First, the front face of the semi-cylinder is stated
perpendicular to flow, than the rear face is placed. The study is
carried out numerically, by using commercial software ANSYS 11.0.
The well-known κ-ε model is applied as the turbulence model.
Reynolds number is in the range of 104 to 105 and air is assumed as
the flowing fluid. The results showed that, heat transfer increased
approximately 15 % in the front faze case, while it enhanced up to 28
% in the rear face case.
Abstract: The purpose of this article is to study the effects of
plants cover on overland flow and, therefore, its influences on the
amount of eroded and transported soil. In this investigation, all the
experiments were conducted in the LEGHYD laboratory using a
rainfall simulator and a soil tray. The experiments were conducted
using an experimental plot (soil tray) which is 2m long, 0.5 m wide
and 0.15 m deep. The soil used is an agricultural sandy soil (62,08%
coarse sand, 19,14% fine sand, 11,57% silt and 7,21% clay). Plastic
rods (4 mm in diameter) were used to simulate the plants at different
densities: 0 stem/m2 (bared soil), 126 stems/m², 203 stems/m², 461
stems/m² and 2500 stems/m²). The used rainfall intensity is 73mm/h
and the soil tray slope is fixed to 3°. The results have shown that the
overland flow velocities decreased with increasing stems density, and
the density cover has a great effect on sediment concentration.
Darcy–Weisbach and Manning friction coefficients of overland flow
increased when the stems density increased. Froude and Reynolds
numbers decreased with increasing stems density and, consequently,
the flow regime of all treatments was laminar and subcritical. From
these findings, we conclude that increasing the plants cover can
efficiently reduce soil loss and avoid denuding the roots plants.
Abstract: Axial Flux Permanent Magnet (AFPM) Machines require effective cooling due to their high power density. The detrimental effects of overheating such as degradation of the insulation materials, magnets demagnetization, and increase of Joule losses are well known. This paper describes the CFD simulations performed on a test rig model of an air cooled Axial Flux Permanent Magnet (AFPM) generator built at Durham University to identify the temperatures and heat transfer coefficient on the stator. The Reynolds Averaged Navier-Stokes and the Energy equations are solved and the flow pattern and heat transfer developing inside the machine are described. The Nusselt number on the stator surfaces has been found. The dependency of the heat transfer on the flow field is described temperature field obtained. Tests on an experimental are undergoing in order to validate the CFD results.
Abstract: Flow around a flat tube is studied numerically. Reynolds number is defined base on equivalent circular tube and it is varied in range of 100 to 300. Equations are solved by using finite volume method and results are presented in form of drag and lift coefficient. Results show that drag coefficient of flat tube is up to 66% lower than circular tube with equivalent diameter. In addition, by increasing l/D from 1 to 2, the drag coefficient of flat tube is decreased about 14-27%.
Abstract: A numerical simulation of vortex-induced vibration of
a 2-dimensional elastic circular cylinder with two degree of freedom
under the uniform flow is calculated when Reynolds is 200.
2-dimensional incompressible Navier-Stokes equations are solved
with the space-time finite element method, the equation of the cylinder
motion is solved with the new explicit integral method and the mesh
renew is achieved by the spring moving mesh technology. Considering
vortex-induced vibration with the low reduced damping parameter, the
variety trends of the lift coefficient, the drag coefficient, the
displacement of cylinder are analyzed under different oscillating
frequencies of cylinder. The phenomena of locked-in, beat and
phases-witch were captured successfully. The evolution of vortex
shedding from the cylinder with time is discussed. There are very
similar trends in characteristics between the results of the one degree
of freedom cylinder model and that of the two degree of freedom
cylinder model. The streamwise vibrations have a certain effect on the
lateral vibrations and their characteristics.
Abstract: The aim of the paper work is to investigate and predict
the static performance of journal bearing in turbulent flow condition
considering micropolar lubrication. The Reynolds equation has been
modified considering turbulent micropolar lubrication and is solved
for steady state operations. The Constantinescu-s turbulence model is
adopted using the coefficients. The analysis has been done for a
parallel and inertia less flow. Load capacity and friction factor have
been evaluated for various operating parameters.