Abstract: A numerical study is presented on convective heat transfer in enclosures. The results are addressed to automotive headlights containing new-age light sources like Light Emitting Diodes (LED). The heat transfer from the heat source (LED) to the enclosure walls is investigated for mixed convection as interaction of the forced convection flow from an inlet and an outlet port and the natural convection at the heat source. Unlike existing studies, inlet and outlet port are thermally coupled and do not serve to remove hot fluid. The input power of the heat source is expressed by the Rayleigh number. The internal position of the heat source, the aspect ratio of the enclosure, and the inclination angle of one wall are varied. The results are given in terms of the global Nusselt number and the enclosure Nusselt number that characterize the heat transfer from the source and from the interior fluid to the enclosure walls, respectively. It is found that the heat transfer from the source to the fluid can be maximized if the source is placed in the main stream from the inlet to the outlet port. In this case, the Reynolds number and heat source position have the major impact on the heat transfer. A disadvantageous position has been found where natural and forced convection compete each other. The overall heat transfer from the source to the wall increases with increasing Reynolds number as well as with increasing aspect ratio and decreasing inclination angle. The heat transfer from the interior fluid to the enclosure wall increases upon decreasing the aspect ratio and increasing the inclination angle. This counteracting behaviour is caused by the variation of the area of the enclosure wall. All mixed convection results are compared to the natural convection limit.
Abstract: In the present study, the pressure drop and laminar convection heat transfer characteristics of nanofluids in microchannel heat sink with square duct are numerically investigated. The water based nanofluids created with Al2O3 and CuO particles in four different volume fractions of 0%, 0.5%, 1%, 1.5% and 2% are used to analyze their effects on heat transfer and the pressure drop. Under the laminar, steady-state flow conditions, the finite volume method is used to solve the governing equations of heat transfer. Mixture Model is considered to simulate the nanofluid flow. For verification of used numerical method, the results obtained from numerical calculations were compared with the results in literature for both pure water and the nanofluids in different volume fractions. The distributions of the particles in base fluid are assumed to be uniform. The results are evaluated in terms of Nusselt number, the pressure drop and heat transfer enhancement. Analysis shows that the nanofluids enhance heat transfer while the Reynolds number and the volume fractions are increasing. The best overall enhancement was obtained at φ=%2 and Re=100 for CuO-water nanofluid.
Abstract: Impinging jets are widely used in industrial cooling
systems for their high heat transfer characteristics at stagnation points.
However, the heat transfer characteristics are low in the downstream
direction. In order to improve the heat transfer coefficient further
downstream, investigations introducing ribs on jet-cooled flat plates
have been conducted. Most studies regarding the heat-transfer
enhancement using a rib-roughened wall have dealt with the rib pitch.
In this paper, we focused on the rib spacing and demonstrated that the
rib spacing must be more than 6 times the nozzle width to improve heat
transfer at Reynolds number Re=5.0×103 because it is necessary to
have enough space to allow reattachment of flow behind the first rib.
Abstract: CFD simulations are carried out in arterial stenoses
with 48 % areal occlusion. Non-newtonian fluid model is selected for
the blood flow as the same problem has been solved before with
Newtonian fluid model. Studies on flow resistance with the presence
of surface irregularities are carried out. Investigations are also
performed on the pressure drop at various Reynolds numbers. The
present study revealed that the pressure drop across a stenosed artery
is practically unaffected by surface irregularities at low Reynolds
numbers, while flow features are observed and discussed at higher
Reynolds numbers.
Abstract: In this work, we examine fluid mixing in a full three-stream mixing channel with longitudinal vortex generators (LVGs) built on the channel bottom by numerical simulation and experiment. The effects of the asymmetrical arrangement and the attack angle of the LVGs on fluid mixing are investigated. The results show that the micromixer with LVGs at a small asymmetry index (defined by the ratio of the distance from the center plane of the gap between the winglets to the center plane of the main channel to the width of the main channel) is superior to the micromixer with symmetric LVGs and that with LVGs at a large asymmetry index. The micromixer using five mixing modules of the LVGs with an attack angle between 16.5 degrees and 22.5 degrees can achieve excellent mixing over a wide range of Reynolds numbers. Here, we call a section of channel with two pairs of staggered asymmetrical LVGs a mixing module. Besides, the micromixer with LVGs at a small attack angle is more efficient than that with a larger attack angle when pressure losses are taken into account.
Abstract: This study presents the numerical simulation of
optimum pin-fin heat sink with air impinging cooling by using
Taguchi method. 9 L ( 4 3 ) orthogonal array is selected as a plan for
the four design-parameters with three levels. The governing
equations are discretized by using the
control-volume-based-finite-difference method with a power-law
scheme on the non-uniform staggered grid. We solved the coupling of
the velocity and the pressure terms of momentum equations using
SIMPLEC algorithm. We employ the k −ε two-equations
turbulence model to describe the turbulent behavior. The parameters
studied include fin height H (35mm-45mm), inter-fin spacing a , b ,
and c (2 mm-6.4 mm), and Reynolds number ( Re = 10000- 25000).
The objective of this study is to examine the effects of the fin
spacings and fin height on the thermal resistance and to find the
optimum group by using the Taguchi method. We found that the fin
spacings from the center to the edge of the heat sink gradually
extended, and the longer the fin’s height the better the results. The
optimum group is 3 1 2 3 H a b c . In addition, the effects of parameters are
ranked by importance as a , H , c , and b .
Abstract: Heavy rainfall greatly affects the aerodynamic performance of the aircraft. There are many accidents of aircraft caused by aerodynamic efficiency degradation by heavy rain.
In this Paper we have studied the heavy rain effects on the aerodynamic efficiency of cambered NACA 64-210 and symmetric
NACA 0012 airfoils. Our results show significant increase in drag and decrease in lift. We used preprocessing software gridgen for creation of geometry and mesh, used fluent as solver and techplot as postprocessor. Discrete phase modeling called DPM is used to model the rain particles using two phase flow approach. The rain particles are assumed to be inert.
Both airfoils showed significant decrease in lift and increase in drag in simulated rain environment. The most significant difference between these two airfoils was the NACA 64-210 more sensitivity than NACA 0012 to liquid water content (LWC). We believe that the results showed in this paper will be useful for the designer of the commercial aircrafts and UAVs, and will be helpful for training of the pilots to control the airplanes in heavy rain.
Abstract: We propose a reduced-ordermodel for the instantaneous
hydrodynamic force on a cylinder. The model consists of a system of
two ordinary differential equations (ODEs), which can be integrated
in time to yield very accurate histories of the resultant force and
its direction. In contrast to several existing models, the proposed
model considers the actual (total) hydrodynamic force rather than its
perpendicular or parallel projection (the lift and drag), and captures
the complete force rather than the oscillatory part only. We study
and provide descriptions of the relationship between the model
parameters, evaluated utilizing results from numerical simulations,
and the Reynolds number so that the model can be used at any
arbitrary value within the considered range of 100 to 500 to provide
accurate representation of the force without the need to perform timeconsuming
simulations and solving the partial differential equations
(PDEs) governing the flow field.
Abstract: Heating is inevitable in any bearing operation. This
leads to not only the thinning of the lubricant but also could lead to a
thermal deformation of the bearing. The present work is an attempt to
analyze the influence of thermal deformation on the thermohydrodynamic
lubrication of infinitely long tilted pad slider rough
bearings. As a consequence of heating the slider is deformed and is
assumed to take a parabolic shape. Also the asperities expand leading
to smaller effective film thickness. Two different types of surface
roughness are considered: longitudinal roughness and transverse
roughness. Christensen-s stochastic approach is used to derive the
Reynolds-type equations. Density and viscosity are considered to be
temperature dependent. The modified Reynolds equation, momentum
equation, continuity equation and energy equation are decoupled and
solved using finite difference method to yield various bearing
characteristics. From the numerical simulations it is observed that the
performance of the bearing is significantly affected by the thermal
distortion of the slider and asperities and even the parallel sliders
seem to carry some load.
Abstract: The present paper represents a methodology for
investigating flow characteristics near orifice plate by using a
commercial computational fluid dynamics code. The flow
characteristics near orifice plate which is located in the auxiliary
feedwater system were modeled via three different levels of grid and
four different types of Reynolds Averaged Navier-Stokes (RANS)
equations with proper near-wall treatment. The results from CFD code
were compared with experimental data in terms of differential pressure
through the orifice plate. In this preliminary study, the Realizable k-ε
and the Reynolds stress models with enhanced wall treatment were
suitable to analyze flow characteristics near orifice plate, and the
results had a good agreement with experimental data.
Abstract: In this research the separation efficiency of deoiling hydrocyclone is evaluated using three-dimensional simulation of multiphase flow based on Eulerian-Eulerian finite volume method. The mixture approach of Reynolds Stress Model is also employed to capture the features of turbulent multiphase swirling flow. The obtained separation efficiency of Colman's design is compared with available experimental data and showed that the separation curve of deoiling hydrocyclones can be predicted using numerical simulation.
Abstract: In the present paper, a numerical investigation has
been carried out to classify and clarify the effects of paramount
parameters on turbulent impinging slot jets. The effects of nozzle-s
exit turbulent intensity, distance between nozzle and impinging plate
are studied at Reynolds number 5000 and 20000. In addition, the
effect of Mach number that is varied between 0.3-0.8 at a constant
Reynolds number 133000 is investigated to elucidate the effect of
compressibility in impinging jet upon a flat plate. The wall that is
located at the same level with nozzle-s exit confines the flow. A
compressible finite volume solver is implemented for simulation the
flow behavior. One equation Spalart-Allmaras turbulent model is
used to simulate turbulent flow at this study. Assessment of the
Spalart-Allmaras turbulent model at high nozzle to plate distance,
and giving enough insights to characterize the effect of Mach number
at high Reynolds number for the complex impinging jet flow are the
remarkable results of this study.
Abstract: A general purpose viscous flow solver Ansys CFX
was used to solve the unsteady three-dimensional (3D) Reynolds
Averaged Navier-Stokes Equation (RANSE) for simulating a 3D
numerical viscous wave tank. A flap-type wave generator was
incorporated in the computational domain to generate the desired
incident waves. Authors have made effort to study the physical
behaviors of Flap type wave maker with governing parameters.
Dependency of the water fill depth, Time period of oscillations and
amplitude of oscillations of flap were studied. Effort has been made
to establish relations between parameters. A validation study was
also carried out against CFD methodology with wave maker theory.
It has been observed that CFD results are in good agreement with
theoretical results. Beaches of different slopes were introduced to
damp the wave, so that it should not cause any reflection from
boundary. As a conclusion this methodology can simulate the
experimental wave-maker for regular wave generation for different
wave length and amplitudes.
Abstract: In this study, the numerical solution of unsteady flow
between two concentric rotating spheres with suction and blowing at
their boundaries is presented. The spheres are rotating about a
common axis of rotation while their angular velocities are constant.
The Navier-Stokes equations are solved by employing the finite
difference method and implicit scheme. The resulting flow patterns
are presented for various values of the flow parameters including
rotational Reynolds number Re , and a blowing/suction Reynolds
number Rew . Viscous torques at the inner and the outer spheres are
calculated, too. It is seen that increasing the amount of suction and
blowing decrease the size of eddies generated in the annulus.
Abstract: In this work, we experimentally study heat transfer
from exhaust particulate air of detergent spray drying tower to water
by using coiled tube heat exchanger. Water flows in the coiled
tubes, where air loaded with detergent particles of 43 micrometers
in diameter flows within the shell. Four coiled tubes with different
coil pitches are used in a counter-current flow configuration. We
investigate heat transfer coefficients of inside and outside the heat
transfer surfaces through 400 experiments. The correlations between
Nusselt number and Reynolds number, Prandtl number, mass flow
rate of particulates to mass flow rate of air ratio and coiled tube
pitch parameter are proposed. The correlations procured can be used
to predicted heat transfer between tube and shell of the heat
exchanger.
Abstract: This paper presents results obtained from the
numerical solution for the flow past an oscillating circular cylinder at
Reynolds number of 200. The frequency of oscillation was fixed to
the vortex shedding frequency from a fixed cylinder, f0, while the
amplitudes of oscillations were varied from to 1.1a, where a
represents the radius of the cylinder. The response of the flow
through the fluid forces acting on the surface of the cylinder are
investigated. The lock-on phenomenon is captured at low oscillation
amplitudes.
Abstract: This research paper presents the CFD analysis of
oscillating airfoil during pitch cycle. Unsteady subsonic flow is
simulated for pitching airfoil at Mach number 0.283 and Reynolds
number 3.45 millions. Turbulent effects are also considered for this
study by using K-ω SST turbulent model. Two-dimensional unsteady
compressible Navier-Stokes code including two-equation turbulence
model and PISO pressure velocity coupling is used. Pressure based
implicit solver with first order implicit unsteady formulation is used.
The simulated pitch cycle results are compared with the available
experimental data. The results have a good agreement with the
experimental data. Aerodynamic characteristics during pitch cycles
have been studied and validated.
Abstract: The purpose of the present study is to analyze the
effect of the target plate-s curvature on the heat transfer in laminar
confined impinging jet flows. Numerical results from two
dimensional compressible finite volume solver are compared
between three different shapes of impinging plates: Flat, Concave
and Convex plates. The remarkable result of this study proves that
the stagnation Nusselt number in laminar range of Reynolds number
based on the slot width is maximum in convex surface and is
minimum in concave plate. These results refuse the previous data in
literature stating the amount of the stagnation Nusselt number is
greater in concave surface related to flat plate configuration.
Abstract: Circle grid space filling plate is a flow conditioner with a fractal pattern and used to eliminate turbulence originating from pipe fittings in experimental fluid flow applications. In this paper, steady state, incompressible, swirling turbulent flow through circle grid space filling plate has been studied. The solution and the analysis were carried out using finite volume CFD solver FLUENT 6.2. Three turbulence models were used in the numerical investigation and their results were compared with the pressure drop correlation of BS EN ISO 5167-2:2003. The turbulence models investigated here are the standard k-ε, realizable k-ε, and the Reynolds Stress Model (RSM). The results showed that the RSM model gave the best agreement with the ISO pressure drop correlation. The effects of circle grids space filling plate thickness and Reynolds number on the flow characteristics have been investigated as well.
Abstract: In this study, a 3D combustion chamber was simulated
using FLUENT 6.32. Aim to obtain detailed information on
combustion characteristics and _ nitrogen oxides in the furnace and
the effect of oxygen enrichment in a combustion process. Oxygenenriched
combustion is an effective way to reduce emissions. This
paper analyzes NO emission, including thermal NO and prompt NO.
Flow rate ratio of air to fuel is varied as 1.3, 3.2 and 5.1 and the
oxygen enriched flow rates are 28, 54 and 68 lit/min. The 3D
Reynolds Averaged Navier Stokes (RANS) equations with standard
k-ε turbulence model are solved together by Fluent 6.32 software.
First order upwind scheme is used to model governing equations and
the SIMPLE algorithm is used as pressure velocity coupling. Results
show that for AF=1.3, increase the oxygen flow rate of oxygen
reduction in NO emissions is Lance. Moreover, in a fixed oxygen
enrichment condition, increasing the air to fuel ratio will increase the
temperature peak, but not the NO emission rate. As a result, oxygen
enrichment can reduce the NO emission at this kind of furnace in low
air to fuel rates.