Abstract: Even it has been recognized that Shape Memory
Alloys (SMA) have a significant potential for deployment actuators,
the number of applications of SMA-based actuators to the present
day is still quite small, due to the need of deep understanding of the
thermo-mechanical behavior of SMA, causing an important need for
a mathematical model able to describe all thermo-mechanical
properties of SMA by relatively simple final set of constitutive
equations. SMAs offer attractive potentials such as: reversible strains
of several percent, generation of high recovery stresses and high
power / weight ratios. The paper tries to provide an overview of the
shape memory functions and a presentation of the designed and
developed temperature control system used for a gripper actuated by
two pairs of differential SMA active springs. An experimental setup
was established, using electrical energy for actuator-s springs heating
process. As for holding the temperature of the SMA springs at certain
level for a long time was developed a control system in order to
avoid the active elements overheating.
Abstract: Palladium-catalyzed hydrodechlorination is a
promising alternative for the treatment of environmentally relevant
water bodies, such as groundwater, contaminated with chlorinated
organic compounds (COCs). In the aqueous phase
hydrodechlorination of COCs, Pd-based catalysts were found to have
a very high catalytic activity. However, the full utilization of the
catalyst-s potential is impeded by the sensitivity of the catalyst to
poisoning and deactivation induced by reduced sulfur compounds
(e.g. sulfides). Several regenerants have been tested before to recover
the performance of sulfide-fouled Pd catalyst. But these only
delivered partial success with respect to re-establishment of the
catalyst activity. In this study, the deactivation behaviour of
Pd/Al2O3 in the presence of sulfide was investigated. Subsequent to
total deactivation the catalyst was regenerated in the aqueous phase
using potassium permanganate. Under neutral pH condition,
oxidative regeneration with permanganate delivered a slow recovery
of catalyst activity. However, changing the pH of the bulk solution to
acidic resulted in the complete recovery of catalyst activity within a
regeneration time of about half an hour. These findings suggest the
superiority of permanganate as regenerant in re-activating Pd/Al2O3
by oxidizing Pd-bound sulfide.
Abstract: To evaluate genetic variation of wheat (Triticum
aestivum) affected by heat and drought stress on eight Australian
wheat genotypes that are parents of Doubled Haploid (HD) mapping
populations at the vegetative stage, the water stress experiment was
conducted at 65% field capacity in growth room. Heat stress
experiment was conducted in the research field under irrigation over
summer. Result show that water stress decreased dry shoot weight
and RWC but increased osmolarity and means of Fv/Fm values in all
varieties except for Krichauff. Krichauff and Kukri had the
maximum RWC under drought stress. Trident variety was shown
maximum WUE, osmolarity (610 mM/Kg), dry mater, quantum yield
and Fv/Fm 0.815 under water stress condition. However, the
recovery of quantum yield was apparent between 4 to 7 days after
stress in all varieties. Nevertheless, increase in water stress after that
lead to strong decrease in quantum yield. There was a genetic
variation for leaf pigments content among varieties under heat stress.
Heat stress decreased significantly the total chlorophyll content that
measured by SPAD. Krichauff had maximum value of Anthocyanin
content (2.978 A/g FW), chlorophyll a+b (2.001 mg/g FW) and
chlorophyll a (1.502 mg/g FW). Maximum value of chlorophyll b
(0.515 mg/g FW) and Carotenoids (0.234 mg/g FW) content
belonged to Kukri. The quantum yield of all varieties decreased
significantly, when the weather temperature increased from 28 ÔùªC to
36 ÔùªC during the 6 days. However, the recovery of quantum yield
was apparent after 8th day in all varieties. The maximum decrease
and recovery in quantum yield was observed in Krichauff. Drought
and heat tolerant and moderately tolerant wheat genotypes were
included Trident, Krichauff, Kukri and RAC875. Molineux, Berkut
and Excalibur were clustered into most sensitive and moderately
sensitive genotypes. Finally, the results show that there was a
significantly genetic variation among the eight varieties that were
studied under heat and water stress.
Abstract: In recent years, environment regulation forcing
manufactures to consider recovery activity of end-of- life products
and/or return products for refurbishing, recycling,
remanufacturing/repair and disposal in supply chain management. In
this paper, a mathematical model is formulated for single product
production-inventory system considering remanufacturing/reuse of
return products and rate of return products follows a demand like
function, dependent on purchasing price and acceptance quality level.
It is useful in decision making to determine whether to go for
remanufacturing or disposal of returned products along with newly
produced products to satisfy a stationary demand. In addition, a
modified genetic algorithm approach is proposed, inspired by particle
swarm optimization method. Numerical analysis of the case study is
carried out to validate the model.
Abstract: Multi-residue analysis method for penicillins was
developed and validated in bovine muscle, chicken, milk, and flatfish.
Detection was based on liquid chromatography tandem mass
spectrometry (LC/MS/MS). The developed method was validated for
specificity, precision, recovery, and linearity. The analytes were
extracted with 80% acetonitrile and clean-up by a single
reversed-phase solid-phase extraction step. Six penicillins presented
recoveries higher than 76% with the exception of Amoxicillin
(59.7%). Relative standard deviations (RSDs) were not more than
10%. LOQs values ranged from 0.1 and to 4.5 ug/kg. The method was
applied to 128 real samples. Benzylpenicillin was detected in 15
samples and Cloxacillin was detected in 7 samples. Oxacillin was
detected in 2 samples. But the detected levels were under the MRL
levels for penicillins in samples.
Abstract: The potential, opportunities and drawbacks of biogas
technology use in Turkey are evaluated in this paper. Turkey is
dependent on foreign sources of energy. Therefore, use of biogas
technology would provide a safe way of waste disposal and recovery
of renewable energy, particularly from a sustainable domestic source,
which is less unlikely to be influenced by international price or
political fluctuations. Use of biogas technology would especially
meet the cooking, heating and electricity demand in rural areas and
protect the environment, additionally creating new job opportunities
and improving social-economical conditions.
Abstract: This research deals with techno economic analysis to select the most economic desalination method for Asalouyeh combined cycle power plant . Due to lack of fresh water, desalination of sea water is necessary to provide required DM water of Power Plant. The most common desalination methods are RO, MSF, MED, and MED–TVC. In this research, methods of RO, MED, and MED– TVC have been compared. Simulation results show that recovery of heat of exhaust gas of main stack is optimum case for providing DM water required for injected steam of MED desalination. This subject is very important because of improving thermal efficiency of power plant using extra heat recovery. Also, it has been shown that by adding 3 rows of finned tube to de-aerator evaporator, which is very simple and low cost, required steam for generating 5200 m3/day of desalinated water is obtainable.
Abstract: Organic Flash Cycle (OFC) has potential of improving
efficiency for recovery of low temperature heat sources mainly due to
reducing temperature mismatch in the heat exchanger. In this work
exergetical performance analysis of ORC is conducted for recovery of
low grade heat source. Effects of system parameters such as flash
evaporation temperature or heating temperature are theoretically
investigated on the exergy destructions (anergies) at various
components of the system as well as exergy efficiency. Results show
that exergy efficiency has a peak with respect to the flash temperature,
and the optimum flash temperature increases with the heating
temperature. The component where the largest exergy destruction
occurs varies with the flash temperature or heating temperature.
Abstract: An improved topology of a voltage-fed quasi-resonant
soft switching LCrCdc series-parallel half bridge inverter with a constant-frequency for electronic ballast applications is proposed in this paper. This new topology introduces a low-cost solution to
reduce switching losses and circuit rating to achieve high-efficiency
ballast. Switching losses effect on ballast efficiency is discussed
through experimental point of view. In this discussion, an improved
topology in which accomplishes soft switching operation over a wide
power regulation range is proposed. The proposed structure uses reverse recovery diode to provide better operation for the ballast system. A symmetrical pulse wide modulation (PWM) control scheme is implemented to regulate a wide range of out-put power.
Simulation results are kindly verified with the experimental
measurements obtained by ballast-lamp laboratory prototype. Different load conditions are provided in order to clarify the
performance of the proposed converter.
Abstract: In switch mode power inverters, small sized inverters
can be obtained by increasing the switching frequency. Switching
frequency increment causes high driver losses. Also, high dt
di
and
dt
dv
produced by the switching action creates high Electromagnetic
Interference (EMI) and Radio Frequency Interference (RFI). In this
paper, a series half bridge series resonant inverter circuit is simulated
and evaluated practically to demonstrate the turn-on and turn-off
conditions during zero or close to zero voltage switching. Also, the
reverse recovery current effects of the body diode of the MOSFETs
were investigated by operating above and below resonant frequency.
Abstract: A co-generation system in automobile can improve
thermal efficiency of vehicle in some degree. The waste heat from the
engine exhaust and coolant is still attractive energy source that reaches
around 60% of the total energy converted from fuel. To maximize the
effectiveness of heat exchangers for recovering the waste heat, it is
vital to select the most suitable working fluid for the system, not to
mention that it is important to find the optimum design for the heat
exchangers. The design of heat exchanger is out of scoop of this study;
rather, the main focus has been on the right selection of working fluid
for the co-generation system. Simulation study was carried out to find
the most suitable working fluid that can allow the system to achieve
the optimum efficiency in terms of the heat recovery rate and thermal
efficiency.
Abstract: Simultaneous recovery of copper and DCA from
simulated MEUF concentrated stream was investigated. Effects of
surfactant (DCA) and metal (copper) concentrations, surfactant to
metal molar ratio (S/M ratio), electroplating voltage, EDTA
concentration, solution pH, and salt concentration on metal recovery
and current efficiency were studied. Electric voltage of -0.5 V was
shown to be optimum operation condition in terms of Cu recovery,
current efficiency, and surfactant recovery. Increasing Cu recovery and
current efficiency were observed with increases of Cu concentration
while keeping concentration of DCA constant. However, increasing
both Cu and DCA concentration while keeping S/M ratio constant at
2.5 showed detrimental effect on Cu recovery at DCA concentration
higher than 15 mM. Cu recovery decreases with increasing pH while
current efficiency showed an opposite trend. It is believed that
conductivity is the main cause for discrepancy of Cu recovery and
current efficiency observed at different pH. Finally, it was shown that
EDTA had adverse effect on both Cu recovery and current efficiency
while addition of NaCl salt had negative impact on current efficiency
at concentration higher than 8000 mg/L.
Abstract: In this paper, we propose a reversible watermarking
scheme based on histogram shifting (HS) to embed watermark bits
into the H.264/AVC standard videos by modifying the last nonzero
level in the context adaptive variable length coding (CAVLC) domain.
The proposed method collects all of the last nonzero coefficients (or
called last level coefficient) of 4×4 sub-macro blocks in a macro
block and utilizes predictions for the current last level from the
neighbor block-s last levels to embed watermark bits. The feature of
the proposed method is low computational and has the ability of
reversible recovery. The experimental results have demonstrated that
our proposed scheme has acceptable degradation on video quality and
output bit-rate for most test videos.
Abstract: In this paper, backup and recovery technique for Peer
to Peer applications, such as a distributed asynchronous Web-Based
Training system that we have previously proposed. In order to
improve the scalability and robustness of this system, all contents and
function are realized on mobile agents. These agents are distributed
to computers, and they can obtain using a Peer to Peer network
that modified Content-Addressable Network. In the proposed system,
although entire services do not become impossible even if some
computers break down, the problem that contents disappear occurs
with an agent-s disappearance. As a solution for this issue, backups
of agents are distributed to computers. If a failure of a computer is
detected, other computers will continue service using backups of the
agents belonged to the computer.
Abstract: In this paper, a fragile watermarking scheme is proposed for color image specified object-s authentication. The color image is first transformed from RGB to YST color space, suitable for watermarking the color media. The T channel corresponds to the chrominance component of a color image andYS ÔèÑ T , therefore selected for embedding the watermark. The T channel is first divided into 2×2 non-overlapping blocks and the two LSBs are set to zero. The object that is to be authenticated is also divided into 2×2 nonoverlapping blocks and each block-s intensity mean is computed followed by eight bit encoding. The generated watermark is then embedded into T channel randomly selected 2×2 block-s LSBs using 2D-Torus Automorphism. Selection of block size is paramount for exact localization and recovery of work. The proposed scheme is blind, efficient and secure with ability to detect and locate even minor tampering applied to the image with full recovery of original work. The quality of watermarked media is quite high both subjectively and objectively. The technique is suitable for class of images with format such as gif, tif or bitmap.
Abstract: The flow field in a centrifugal fan is highly complex
with flow reversal taking place on the suction side of impeller and
diffuser vanes. Generally performance of the centrifugal fan could be
enhanced by judiciously introducing splitter vanes so as to improve
the diffusion process. An extensive numerical whole field analysis on
the effect of splitter vanes placed in discrete regions of suspected
separation points is possible using CFD. This paper examines the
effect of splitter vanes corresponding to various geometrical
locations on the impeller and diffuser. The analysis shows that the
splitter vanes located near the diffuser exit improves the static
pressure recovery across the diffusing domain to a larger extent. Also
it is found that splitter vanes located at the impeller trailing edge and
diffuser leading edge at the mid-span of the circumferential distance
between the blades show a marginal improvement in the static
pressure recovery across the fan. However, splitters provided near to
the suction side of the impeller trailing edge (25% of the
circumferential gap between the impeller blades towards the suction
side), adversely affect the static pressure recovery of the fan.
Abstract: Green incentives are included in the “American
Recovery and Reinvestment Act of 2009" (ARRA). It is, however,
unclear how these government incentives can be carried out most
effectively according to market-based principles and if they can serve
as a catalyst for an accelerated green transformation and an ultimate
solution to the current U.S. and global economic and financial crisis.
The article will compare the existing U.S. green economic policies
with those in Germany, identify problems, and suggest improvements
to allow the green stimulus incentives to achieve the best results in
the process of an accelerated green transformation. The author argues
that the current U.S. green stimulus incentives can only be most
successful if they are carried out as part of a visionary,
comprehensive, long-term, and consistent strategy of the green
economic transformation.
Abstract: Modernizing legacy applications is the key issue facing IT managers today because there's enormous pressure on organizations to change the way they run their business to meet the new requirements. The importance of software maintenance and reengineering is forever increasing. Understanding the architecture of existing legacy applications is the most critical issue for maintenance and reengineering. The artifacts recovery can be facilitated with different recovery approaches, methods and tools. The existing methods provide static and dynamic set of techniques for extracting architectural information, but are not suitable for all users in different domains. This paper presents a simple and lightweight pattern extraction technique to extract different artifacts from legacy systems using regular expression pattern specifications with multiple language support. We used our custom-built tool DRT to recover artifacts from existing system at different levels of abstractions. In order to evaluate our approach a case study is conducted.
Abstract: The modified Claus process is commonly used in oil
refining and gas processing to recover sulfur and destroy
contaminants formed in upstream processing. A Claus furnace feed
containing a relatively low concentration of H2S may be incapable of
producing a stable flame. Also, incomplete combustion of
hydrocarbons in the feed can lead to deterioration of the catalyst in
the reactors due to soot or carbon deposition. Therefore, special
consideration is necessary to achieve the appropriate overall sulfur
recovery. In this paper, some configurations available to treat lean
acid gas streams are described and the most appropriate ones are
studied to overcome low H2S concentration problems. As a result,
overall sulfur recovery is investigated for feed preheating and hot gas
configurations.
Abstract: This paper considers a robust recovery of sparse frequencies
from partial phase-only measurements. With the proposed
method, sparse frequencies can be reconstructed, which makes full
use of the sparse distribution in the Fourier representation of the
complex-valued time signal. Simulation experiments illustrate the
proposed method-s advantages over conventional methods in both
noiseless and additive white Gaussian noise cases.