Abstract: The paper examines the mechanism of pozzolan-soil reactions, using a recent study on the chemical stabilization of a Class A-2-7 (3) lateritic soil, with corn cob ash (CCA) as case study. The objectives are to establish a nexus between cation exchange capacity of the soil, the alkaline forming compounds in CCA and percentage CCA addition to soil beyond which no more improvement in strength properties can be achieved; and to propose feasible chemical reactions to explain the chemical stabilization of the lateritic soil with CCA alone. The lateritic soil, as well as CCA of pozzolanic quality Class C were separately analysed for their metallic oxide composition using the X-Ray Fluorescence technique. The cation exchange capacity (CEC) of the soil and the CCA were computed theoretically using the percentage composition of the base cations Ca2+, Mg2+ K+ and Na2+ as 1.48 meq/100 g and 61.67 meq/100 g respectively, thus indicating a ratio of 0.024 or 2.4%. This figure, taken as the theoretical amount required to just fill up the exchangeable sites of the clay molecules, compares well with the laboratory observation of 1.5% for the optimum level of CCA addition to lateritic soil. The paper went on to present chemical reaction equations between the alkaline earth metals in the CCA and the silica in the lateritic soil to form silicates, thereby proposing an extension of the theory of mechanism of soil stabilization to cover chemical stabilization with pozzolanic ash only. The paper concluded by recommending further research on the molecular structure of soils stabilized with pozzolanic waste ash alone, with a view to confirming the chemical equations advanced in the study.
Abstract: Recently, copper and manganese-containing systems are recognized as active and selective catalysts in many oxidation reactions. The main idea of this study is to obtain more information about γ-Al2O3 supported Cu-La catalysts and to evaluate their activity to simultaneous oxidation of CO, CH3OH and dimethyl ether (DME). The catalysts were synthesized by impregnation of support with a mixed aqueous solution of nitrates of copper, manganese and lanthanum under different conditions. XRD, HRTEM/EDS, TPR and thermal analysis were performed to investigate catalysts’ bulk and surface properties. The texture characteristics were determined by Quantachrome Instruments NOVA 1200e specific surface area and pore analyzer. The catalytic measurements of single compounds oxidation were carried out on continuous flow equipment with a four-channel isothermal stainless steel reactor in a wide temperature range. On the basis of XRD analysis and HRTEM/EDS, it was concluded that the active component of the mixed Cu-Mn-La/γ–alumina catalysts strongly depends on the Cu/Mn molar ratio and consisted of at least four compounds – CuO, La2O3, MnO2 and Cu1.5Mn1.5O4. A homogeneous distribution of the active component on the carrier surface was found. The chemical composition strongly influenced catalytic properties. This influence was quite variable with regards to the different processes.
Abstract: Zymomonas mobilis is known as an example of the
uncoupled growth phenomenon. This microorganism also has a
unique metabolism that degrades glucose by the Entner–Doudoroff
(ED) pathway. In this paper, a genome-scale metabolic model
including 434 genes, 757 reactions and 691 metabolites was
reconstructed to simulate uncoupled growth and study its effect on
flux distribution in the central metabolism. The model properly
predicted that ATPase was activated in experimental growth yields of
Z. mobilis. Flux distribution obtained from model indicates that the
major carbon flux passed through ED pathway that resulted in the
production of ethanol. Small amounts of carbon source were entered
into pentose phosphate pathway and TCA cycle to produce biomass
precursors. Predicted flux distribution was in good agreement with
experimental data. The model results also indicated that Z. mobilis
metabolism is able to produce biomass with maximum growth yield
of 123.7 g (mol glucose)-1 if ATP synthase is coupled with growth
and produces 82 mmol ATP gDCW-1h-1. Coupling the growth and
energy reduced ethanol secretion and changed the flux distribution to
produce biomass precursors.
Abstract: Entropy, as an outcome of the second law of thermodynamics, measures the level of irreversibility associated with any process. The identification and reduction of irreversibility in the energy conversion process helps to improve the efficiency of the system. The entropy of pure substances known as absolute entropy is determined at an absolute reference point and is useful in the thermodynamic analysis of chemical reactions; however, municipal solid waste (MSW) is a structurally complicated material with unknown absolute entropy. In this work, an empirical model to calculate the absolute entropy of MSW based on the content of carbon, hydrogen, oxygen, nitrogen, sulphur, and chlorine on a dry ash free basis (daf) is presented. The proposed model was derived from 117 relevant organic substances which represent the main constituents in MSW with known standard entropies using statistical analysis. The substances were divided into different waste fractions; namely, food, wood/paper, textiles/rubber and plastics waste and the standard entropies of each waste fraction and for the complete mixture were calculated. The correlation of the standard entropy of the complete waste mixture derived was found to be somsw= 0.0101C + 0.0630H + 0.0106O + 0.0108N + 0.0155S + 0.0084Cl (kJ.K-1.kg) and the present correlation can be used for estimating the absolute entropy of MSW by using the elemental compositions of the fuel within the range of 10.3% ≤ C ≤ 95.1%, 0.0% ≤ H ≤ 14.3%, 0.0% ≤ O ≤ 71.1%, 0.0 ≤ N ≤ 66.7%, 0.0% ≤ S ≤ 42.1%, 0.0% ≤ Cl ≤ 89.7%. The model is also applicable for the efficient modelling of a combustion system in a waste-to-energy plant.
Abstract: This paper demonstrates the use of a method of synthesizing process flowsheets using a graphical tool called the GH-plot and in particular, to look at how it can be used to compare the reactions of a combined simultaneous process with regard to their thermodynamics. The technique uses fundamental thermodynamic principles to allow the mass, energy and work balances locate the attainable region for chemical processes in a reactor. This provides guidance on what design decisions would be best suited to developing new processes that are more effective and make lower demands on raw material and energy usage.
Abstract: In recent times, we noticed an interesting and important
role of non-coplanar degree-of-freedom (Φ = 00) in heavy ion
reactions. Using the dynamical cluster-decay model (DCM) with
Φ degree-of-freedom included, we have studied three compound
systems 246Bk∗, 164Yb∗ and 105Ag∗. Here, within the DCM with
pocket formula for nuclear proximity potential, we look for the
effects of including compact, non-coplanar configurations (Φc = 00)
on the non-compound nucleus (nCN) contribution in total fusion
cross section σfus. For 246Bk∗, formed in 11B+235U and 14N+232Th
reaction channels, the DCM with coplanar nuclei (Φc = 00) shows
an nCN contribution for 11B+235U channel, but none for 14N+232Th
channel, which on including Φ gives both reaction channels as
pure compound nucleus decays. In the case of 164Yb∗, formed in
64Ni+100Mo, the small nCN effects for Φ=00 are reduced to almost
zero for Φ = 00. Interestingly, however, 105Ag∗ for Φ = 00 shows a
small nCN contribution, which gets strongly enhanced for Φ = 00,
such that the characteristic property of PCN presents a change of
behaviour, like that of a strongly fissioning superheavy element to a
weakly fissioning nucleus; note that 105Ag∗ is a weakly fissioning
nucleus and Psurv behaves like one for a weakly fissioning nucleus
for both Φ = 00 and Φ = 00. Apparently, Φ is presenting itself like
a good degree-of-freedom in the DCM.
Abstract: Recently, fluidized bed gasification becomes an attractive technology for power generation due to its higher efficiency. The main objective pursued in this work is to investigate the producer gas production potential from sized biomass (sawdust and pigeon pea) by applying the air gasification technique. The size of the biomass selected for the study was in the range of 0.40-0.84 mm. An experimental study was conducted using a fluidized bed gasifier with 210 mm diameter and 1600 mm height. During the experiments, the fuel properties and the effects of operating parameters such as gasification temperatures 700 to 900 °C, equivalence ratio 0.16 to 0.46 were studied. It was concluded that substantial amounts of producer gas (up to 1110 kcal/m3) could be produced utilizing biomass such as sawdust and pigeon pea by applying this fluidization technique. For both samples, the rise of temperature till 900 °C and equivalence ratio of 0.4 favored further gasification reactions and resulted into producer gas with calorific value 1110 kcal/m3.
Abstract: Clustering phenomenon of pellets was observed frequently in shaft processes operating at higher temperatures. Clustering is a result of the growth of fibrous iron precipitates (iron whiskers) that become hooked to each other and finally become crystallized during the initial stages of metallization. If the pellet clustering is pronounced, sometimes leads to blocking inside the furnace and forced shutdown takes place. This work clarifies further the relation between metallic iron whisker growth and iron ore mineralogy. Various pellet sizes (6 – 12.0 & +12.0 mm) from three different ores (A, B & C) were (completely and partially) reduced at 985 oC with H2/CO gas mixture using thermos-gravimetric technique. It was found that reducibility increases by decreasing the iron ore pellet’s size. Ore (A) has the highest reducibility than ore (B) and ore (C). Increasing the iron ore pellet’s size leads to increase the probability of metallic iron whisker formation. Ore (A) has the highest tendency for metallic iron whisker formation than ore (B) and ore (C). The reduction reactions for all iron ores A, B and C are mainly controlled by diffusion reaction mechanism.
Abstract: The thermochemical copper-chlorine (Cu-Cl) cycle is considered as a sustainable and efficient technology for a hydrogen production, when linked with clean-energy systems such as nuclear reactors or solar thermal plants. In the Cu-Cl cycle, water is decomposed thermally into hydrogen and oxygen through a series of intermediate reactions. This paper investigates the thermal scale up analysis of the three phase oxygen production reactor in the Cu-Cl cycle, where the reaction is endothermic and the temperature is about 530 oC. The paper focuses on examining the size and number of oxygen reactors required to provide enough heat input for different rates of hydrogen production. The type of the multiphase reactor used in this paper is the continuous stirred tank reactor (CSTR) that is heated by a half pipe jacket. The thermal resistance of each section in the jacketed reactor system is studied to examine its effect on the heat balance of the reactor. It is found that the dominant contribution to the system thermal resistance is from the reactor wall. In the analysis, the Cu-Cl cycle is assumed to be driven by a nuclear reactor where two types of nuclear reactors are examined as the heat source to the oxygen reactor. These types are the CANDU Super Critical Water Reactor (CANDU-SCWR) and High Temperature Gas Reactor (HTGR). It is concluded that a better heat transfer rate has to be provided for CANDU-SCWR by 3-4 times than HTGR. The effect of the reactor aspect ratio is also examined in this paper and is found that increasing the aspect ratio decreases the number of reactors and the rate of decrease in the number of reactors decreases by increasing the aspect ratio. Finally, a comparison between the results of heat balance and existing results of mass balance is performed and is found that the size of the oxygen reactor is dominated by the heat balance rather than the material balance.
Abstract: The goal of engineering education is to prepare students to cope with problems of real devices and systems. Usually there are not enough devices or time for conducting experiments in a real lab. Other factors that prevent the use of lab devices directly by students are inaccessible or dangerous phenomena, or polluting chemical reactions. The technology brings additional strategies of learning and teaching, there are two types of online labs, virtual and remote labs RL. We present an example of a successful development and deployment of a remote lab in the field of engineering education, integrated in the Moodle platform, using very low-coast, high documented devices and free software. The remote lab is user friendly for both teachers and students. Our web 2.0 based user interface would attract and motivate students, as well as solving the problem of larger classes and expensive lab devices.
Abstract: Wetting efficiency of microstructures or nanostructures patterned on Si wafers is a real challenge in integrated circuits manufacturing. In fact, bad or non-uniform wetting during wet processes limits chemical reactions and can lead to non-complete etching or cleaning inside the patterns and device defectivity. This issue is more and more important with the transistors size shrinkage and concerns mainly high aspect ratio structures. Deep Trench Isolation (DTI) structures enabling pixels’ isolation in imaging devices are subject to this phenomenon. While low-frequency acoustic reflectometry principle is a well-known method for Non Destructive Test applications, we have recently shown that it is also well suited for nanostructures wetting characterization in a higher frequency range. In this paper, we present a high-frequency acoustic reflectometry characterization of DTI wetting through a confrontation of both experimental and modeling results. The acoustic method proposed is based on the evaluation of the reflection of a longitudinal acoustic wave generated by a 100 µm diameter ZnO piezoelectric transducer sputtered on the silicon wafer backside using MEMS technologies. The transducers have been fabricated to work at 5 GHz corresponding to a wavelength of 1.7 µm in silicon. The DTI studied structures, manufactured on the wafer frontside, are crossing trenches of 200 nm wide and 4 µm deep (aspect ratio of 20) etched into a Si wafer frontside. In that case, the acoustic signal reflection occurs at the bottom and at the top of the DTI enabling its characterization by monitoring the electrical reflection coefficient of the transducer. A Finite Difference Time Domain (FDTD) model has been developed to predict the behavior of the emitted wave. The model shows that the separation of the reflected echoes (top and bottom of the DTI) from different acoustic modes is possible at 5 Ghz. A good correspondence between experimental and theoretical signals is observed. The model enables the identification of the different acoustic modes. The evaluation of DTI wetting is then performed by focusing on the first reflected echo obtained through the reflection at Si bottom interface, where wetting efficiency is crucial. The reflection coefficient is measured with different water / ethanol mixtures (tunable surface tension) deposited on the wafer frontside. Two cases are studied: with and without PFTS hydrophobic treatment. In the untreated surface case, acoustic reflection coefficient values with water show that liquid imbibition is partial. In the treated surface case, the acoustic reflection is total with water (no liquid in DTI). The impalement of the liquid occurs for a specific surface tension but it is still partial for pure ethanol. DTI bottom shape and local pattern collapse of the trenches can explain these incomplete wetting phenomena. This high-frequency acoustic method sensitivity coupled with a FDTD propagative model thus enables the local determination of the wetting state of a liquid on real structures. Partial wetting states for non-hydrophobic surfaces or low surface tension liquids are then detectable with this method.
Abstract: In this paper, a PSO based fractional order PID (FOPID) controller is proposed for concentration control of an isothermal Continuous Stirred Tank Reactor (CSTR) problem. CSTR is used to carry out chemical reactions in industries, which possesses complex nonlinear dynamic characteristics. Particle Swarm Optimization algorithm technique, which is an evolutionary optimization technique based on the movement and intelligence of swarm is proposed for tuning of the controller for this system. Comparisons of proposed controller with conventional and fuzzy based controller illustrate the superiority of proposed PSO-FOPID controller.
Abstract: The new methods as accelerated steam distillation
assisted by microwave (ASDAM) is a combination of microwave
heating and steam distillation, performed at atmospheric pressure at
very short extraction time. Isolation and concentration of volatile
compounds are performed by a single stage. (ASDAM) has been
compared with (ASDAM) with cryogrinding of seeds (CG) and a
conventional technique, hydrodistillation assisted by microwave
(HDAM), hydro-distillation (HD) for the extraction of essential oil
from aromatic herb as caraway and cumin seeds. The essential oils
extracted by (ASDAM) for 1 min were quantitatively (yield) and
qualitatively (aromatic profile) no similar to those obtained by
ASDAM-CG (1 min) and HD (for 3 h). The accelerated microwave
extraction with cryogrinding inhibits numerous enzymatic reactions
as hydrolysis of oils.
Microwave radiations constitute the adequate mean for the
extraction operations from the yields and high content in major
component majority point view, and allow to minimise considerably
the energy consumption, but especially heating time too, which is one
of essential parameters of artifacts formation.
The ASDAM and ASDAM-CG are green techniques and yields an
essential oil with higher amounts of more valuable oxygenated
compounds comparable to the biosynthesis compounds, and allows
substantial savings of costs, in terms of time, energy and plant
material.
Abstract: Torrefaction of biomass pellets is considered as a
useful pretreatment technology in order to convert them into a high
quality solid biofuel that is more suitable for pyrolysis, gasification,
combustion, and co-firing applications. In the course of torrefaction,
the temperature varies across the pellet, and therefore chemical
reactions proceed unevenly within the pellet. However, the
uniformity of the thermal distribution along the pellet is generally
assumed. The torrefaction process of a single cylindrical pellet is
modeled here, accounting for heat transfer coupled with chemical
kinetics. The drying sub-model was also introduced. The nonstationary
process of wood pellet decomposition is described by the
system of non-linear partial differential equations over the
temperature and mass. The model captures well the main features of
the experimental data.
Abstract: This study evaluated the acute toxicity and tissue
distribution of intravenously administered gold nanoparticles
(AuNPs) in male rabbits. Rabbits were exposed to single dose of
AuNPs (300 μg/ kg). Toxic effects were assessed via general
behavior, hematological parameters, serum biochemical parameters,
and histopathological examination of various rabbits’ organs.
Inductively coupled plasma–mass spectrometry (ICP-MS) was used
to determine gold concentrations in tissue samples collected at
predetermined time intervals. After one week, AuNPs exerted no
obvious acute toxicity in rabbits. However, inflammatory reactions
were observed in liver, lungs and kidneys accompanied with mild
absolute neutrophilia and significant monocytosis. The highest gold
levels were found in the spleen and liver followed by lungs, and
kidneys. These results indicated that AuNPs could be distributed
extensively to various tissues in the body, but primarily in the spleen
and liver.
Abstract: The transesterification of dimethyl malonate (DMM)
with phenol has been studied in vapour phase over cordierite
honeycomb coated with solid acid catalysts such as ZrO2,
Mo(VI)/ZrO2 and SO42-/ZrO2. The catalytic materials were prepared
honeycomb coated, powder forms, and characterized for their total
surface acidity by NH3-TPD and crystalinity by powder XRD
methods. Phenyl methyl malonate (PMM) and diphenyl malonate
(DPM) were obtained as the reaction products. A good conversion of
DMM (up to 82%) of MPM with 95% selectivity was observed when
the reactions were carried out at a catalyst bed temperature of 200 °C
and flow-rate of 10 mL/h in presence of Mo(VI)/ZrO2 as catalyst.
However, over SO4^2-/ZrO2 catalyst, the yield of DPM was found to be
higher. The results have been interpreted based on the variation of
acidic properties and powder XRD phases of zirconia on
incorporation of Mo(VI) or SO42– ions. Transesterification reactions
were also carried out over powder forms of the catalytic materials
and the yield of the desired phenyl ester products were compared
with that of the HC coated catalytic materials. The solid acids were
found to be reusable when used for at least 5 reaction cycles.
Abstract: The aim of the study is to compare behavioral and
EEG reactions in Turkic-speaking inhabitants of Siberia (Tuvinians
and Yakuts) and Russians during the recognition of syntax errors in
native and foreign languages. Sixty-three healthy aboriginals of the
Tyva Republic, 29 inhabitants of the Sakha (Yakutia) Republic, and
55 Russians from Novosibirsk participated in the study. EEG were
recorded during execution of error-recognition task in Russian and
English language (in all participants) and in native languages
(Tuvinian or Yakut Turkic-speaking inhabitants). Reaction time (RT)
and quality of task execution were chosen as behavioral measures.
Amplitude and cortical distribution of P300 and P600 peaks of ERP
were used as a measure of speech-related brain activity. In Tuvinians,
there were no differences in the P300 and P600 amplitudes as well as
in cortical topology for Russian and Tuvinian languages, but there
was a difference for English. In Yakuts, the P300 and P600
amplitudes and topology of ERP for Russian language were the same
as Russians had for native language. In Yakuts, brain reactions during
Yakut and English language comprehension had no difference, while
the Russian language comprehension was differed from both Yakut
and English. We found out that the Tuvinians recognized both Russian and
Tuvinian as native languages, and English as a foreign language. The
Yakuts recognized both English and Yakut as foreign languages, but
Russian as a native language. According to the inquirer, both
Tuvinians and Yakuts use the national language as a spoken
language, whereas they do not use it for writing. It can well be a
reason that Yakuts perceive the Yakut writing language as a foreign
language while writing Russian as their native.
Abstract: Urinary Tract Infections are considered as one of the
most common bacterial infections with an estimated annual global
incidence of 150 million. Antimicrobial drug resistance is one of the
major threats due to wide spread usage of uncontrolled antibiotics. In
this study, a total number of 9149 urine samples were collected from
R.H Patiala and processed in the Department of Microbiology G. M.
C Patiala (January 2013 to December 2013). Urine samples were
inoculated on MacConkey’s and blood agar plates and incubated at
370C for 24 hrs. The organisms were identified by colony characters,
Gram’s staining, and biochemical reactions. Antimicrobial
susceptibility of the isolates was determined against various
antimicrobial agents (Hi – Media Mumbai India) by Kirby Bauer
DISK diffusion method on Muller Hinton agar plates. Maximum patients were in the age group of 21-30 yrs followed by
31-40 yrs. Males (34%) are less prone to urinary tract infections than
females (66%). Culture was positive in 25% of the samples.
Escherichia coli was the most common isolate 60.3% followed by
Klebsiella pneumoniae 13.5%, Proteus spp. 9% and Staphylococcus
aureus 7.6%. Most of the urinary isolates were sensitive to,
carbepenems, Aztreonam, Amikacin, and Piperacillin + Tazobactum.
All the isolates showed a good sensitivity towards Nitrofurantoin
(82%). ESBL production was found to be 70.6% in Escherichia coli
and 29.4% in Klebsiella pneumonia. Susceptibility of ESBL
producers to Imipenem, Nitrofurantoin and Amikacin were found to
be 100%, 76%, and 75% respectively. Uropathogens are increasingly
showing resistance to many antibiotics making empiric management
of outpatient UTIs challenging. Ampicillin, Cotrimoxazole and
Ciprofloxacin should not be used in empiric treatment. Nitrofurantoin
could be used in lower urinary tract infection. Knowledge of
uropathogens and their antimicrobial susceptibility pattern in a
geographical region will help in appropriate and judicious antibiotic
usage in a health care setup.
Abstract: Ultraviolet photocatalytic oxidation (UV-PCO)
technology has been recommended as a green approach to health
indoor environment when it is integrated into mechanical ventilation
systems for inorganic and organic compounds removal as well as
energy saving due to less outdoor air intakes. Although much research
has been devoted to UV-PCO, limited information is available on the
UV-PCO behavior tested by the mixtures in literature. This project
investigated UV-PCO performance and by-product generation using a
single and a mixture of acetone and MEK at 100 ppb each in a
single-pass duct system in an effort to obtain knowledge associated
with competitive photochemical reactions involved in. The
experiments were performed at 20 % RH, 22 °C, and a gas flow rate of
128 m3/h (75 cfm). Results show that acetone and MEK mutually
reduced each other’s PCO removal efficiency, particularly negative
removal efficiency for acetone. These findings were different from
previous observation of facilitatory effects on the adsorption of
acetone and MEK on photocatalyst surfaces.
Abstract: Numerous investigations suggest that Mesenchymal
Stem Cells (MSCs) in general represent a valuable tool for therapy of
symptoms related to chronic inflammatory diseases. Blue Horizon
Stem Cell Therapy Program is a leading provider of adult and
children’s stem cell therapies. Uniquely we have safely and
efficiently treated more than 600 patients with documenting each
procedure. The purpose of our study is primarily to monitor the
immune response in order to validate the safety of intravenous
infusion of human umbilical cord blood derived MSCs (UC-MSCs),
and secondly, to evaluate effects on biomarkers associated with
chronic inflammation. Nine patients were treated for conditions
associated with chronic inflammation and for the purpose of antiaging.
They have been given one intravenous infusion of UCMSCs.
Our study of blood test markers of 9 patients with chronic
inflammation before and within three months after MSCs treatment
demonstrates that there is no significant changes and MSCs treatment
was safe for the patients. Analysis of different indicators of chronic
inflammation and aging included in initial, 24-hours, two weeks and
three months protocols showed that stem cell treatment was safe for
the patients; there were no adverse reactions. Moreover data from
follow up protocols demonstrates significant improvement in energy
level, hair, nails growth and skin conditions. Intravenously
administered UC-MSCs were safe and effective in the improvement
of symptoms related to chronic inflammation. Further close
monitoring and inclusion of more patients are necessary to fully
characterize the advantages of UC-MSCs application in treatment of
symptoms related to chronic inflammation.