Abstract: Numerical analysis for the aerodynamic characteristics
of the WIG (wing-in ground effect) craft with highly cambered and
aspect ratio of one is performed to predict the ground effect for the
case of with- and without- lower-extension endplate. The analysis is
included varying angles of attack from 0 to10 deg. and ground
clearances from 5% of chord to 50%. Due to the ground effect, the lift
by rising in pressure on the lower surface is increased and the
influence of wing-tip vortices is decreased. These two significant
effects improve the lift-drag ratio. On the other hand, the endplate
prevents the high-pressure air escaping from the air cushion at the
wing tip and causes to increase the lift and lift-drag ratio further. It is
found from the visualization of computation results that two wing-tip
vortices are generated from each surface of the wing tip and their
strength are weak and diminished rapidly. Irodov-s criteria are also
evaluated to investigate the static height stability. The comparison of
Irodov-s criteria shows that the endplate improves the deviation of the
static height stability with respect to pitch angles and heights. As the
results, the endplate can improve the aerodynamic characteristics and
static height stability of wings in ground effect, simultaneously.
Abstract: Rapid urbanization, industrialization and population
growth have led to an increase in number of automobiles that cause
air pollution. It is estimated that road traffic contributes 60% of air
pollution in urban areas. A case by case assessment is required to
predict the air quality in urban situations, so as to evolve certain
traffic management measures to maintain the air quality levels with
in the tolerable limits. Calicut city in the state of Kerala, India has
been chosen as the study area. Carbon Monoxide (CO) concentration
was monitored at 15 links in Calicut city and air quality performance
was evaluated over each link. The CO pollutant concentration values
were compared with the National Ambient Air Quality Standards
(NAAQS), and the CO values were predicted by using CALINE4 and
IITLS and Linear regression models. The study has revealed that
linear regression model performs better than the CALINE4 and
IITLS models. The possible association between CO pollutant
concentration and traffic parameters like traffic flow, type of vehicle,
and traffic stream speed was also evaluated.
Abstract: We present the development of a new underwater laser
cutting process in which a water-jet has been used along with the
laser beam to remove the molten material through kerf. The
conventional underwater laser cutting usually utilizes a high pressure
gas jet along with laser beam to create a dry condition in the cutting
zone and also to eject out the molten material. This causes a lot of gas
bubbles and turbulence in water, and produces aerosols and waste
gas. This may cause contamination in the surrounding atmosphere
while cutting radioactive components like burnt nuclear fuel. The
water-jet assisted underwater laser cutting process produces much
less turbulence and aerosols in the atmosphere. Some amount of
water vapor bubbles is formed at the laser-metal-water interface;
however, they tend to condense as they rise up through the
surrounding water. We present the design and development of a
water-jet assisted underwater laser cutting head and the parametric
study of the cutting of AISI 304 stainless steel sheets with a 2 kW
CW fiber laser. The cutting performance is similar to that of the gas
assist laser cutting; however, the process efficiency is reduced due to
heat convection by water-jet and laser beam scattering by vapor. This
process may be attractive for underwater cutting of nuclear reactor
components.
Abstract: Economically transformers constitute one of the largest investments in a Power system. For this reason, transformer condition assessment and management is a high priority task. If a transformer fails, it would have a significant negative impact on revenue and service reliability. Monitoring the state of health of power transformers has traditionally been carried out using laboratory Dissolved Gas Analysis (DGA) tests performed at periodic intervals on the oil sample, collected from the transformers. DGA of transformer oil is the single best indicator of a transformer-s overall condition and is a universal practice today, which started somewhere in the 1960s. Failure can occur in a transformer due to different reasons. Some failures can be limited or prevented by maintenance. Oil filtration is one of the methods to remove the dissolve gases and prevent the deterioration of the oil. In this paper we analysis the DGA data by regression method and predict the gas concentration in the oil in the future. We bring about a comparative study of different traditional methods of regression and the errors generated out of their predictions. With the help of these data we can deduce the health of the transformer by finding the type of fault if it has occurred or will occur in future. Additional in this paper effect of filtration on the transformer health is highlight by calculating the probability of failure of a transformer with and without oil filtrating.
Abstract: In the past years, the world has witnessed significant work in the field of Manufacturing. Special efforts have been made in the implementation of new technologies, management and control systems, among many others which have all evolved the field. Closely following all this, due to the scope of new projects and the need of turning the existing flexible ideas into more autonomous and intelligent ones, i.e.: moving toward a more intelligent manufacturing, the present paper emerges with the main aim of contributing to the analysis and a few customization issues of a new iCIM 3000 system at the IPSAM. In this process, special emphasis in made on the material flow problem. For this, besides offering a description and analysis of the system and its main parts, also some tips on how to define other possible alternative material flow scenarios and a partial analysis of the combinatorial nature of the problem are offered as well. All this is done with the intentions of relating it with the use of simulation tools, for which these have been briefly addressed with a special focus on the Witness simulation package. For a better comprehension, the previous elements are supported by a few figures and expressions which would help obtaining necessary data. Such data and others will be used in the future, when simulating the scenarios in the search of the best material flow configurations.
Abstract: The purpose of the study was to determine if, among
32 brain injured adults in community rehabilitation programs, there is
a statistically significant relationship between the degree of severity
of brain injury and these adults- level of self-esteem and stress. The
researcher hypothesized there would be a statistically significant
difference and a statistically significant relationship in self-esteem
and stress levels among and TBI adults. A Pearson product moment
correlational analysis was implemented and results found a
statistically significant relationship between self-esteem and stress
levels. Future recommendations were suggested upon completion of
research.
Abstract: Lately, significant work in the area of Intelligent
Manufacturing has become public and mainly applied within the
frame of industrial purposes. Special efforts have been made in the
implementation of new technologies, management and control
systems, among many others which have all evolved the field. Aware
of all this and due to the scope of new projects and the need of
turning the existing flexible ideas into more autonomous and
intelligent ones, i.e.: Intelligent Manufacturing, the present paper
emerges with the main aim of contributing to the design and analysis
of the material flow in either systems, cells or work stations under
this new “intelligent" denomination. For this, besides offering a
conceptual basis in some of the key points to be taken into account
and some general principles to consider in the design and analysis of
the material flow, also some tips on how to define other possible
alternative material flow scenarios and a classification of the states a
system, cell or workstation are offered as well. All this is done with
the intentions of relating it with the use of simulation tools, for which
these have been briefly addressed with a special focus on the Witness
simulation package. For a better comprehension, the previous
elements are supported by a detailed layout, other figures and a few
expressions which could help obtaining necessary data. Such data and
others will be used in the future, when simulating the scenarios in the
search of the best material flow configurations.
Abstract: Candida albicans ATCC 10231 had low endogenous activity of the alternative oxidase compared with that of C. albicans ATCC 10261. In C. albicans ATCC 10231 the endogenous activity declined as the cultures aged. Alternative oxidase activity could be induced in C. albicans ATCC 10231 by treatment with cyanide, but the induction of this activity required the presence of oxygen which could be replaced, at least in part, with high concentrations of potassium ferricyanide. We infer from this that the expression of the gene encoding the alternative oxidase is under the control of a redoxsensitive transcription factor.
Abstract: The approach of subset selection in polynomial
regression model building assumes that the chosen fixed full set of
predefined basis functions contains a subset that is sufficient to
describe the target relation sufficiently well. However, in most cases
the necessary set of basis functions is not known and needs to be
guessed – a potentially non-trivial (and long) trial and error process.
In our research we consider a potentially more efficient approach –
Adaptive Basis Function Construction (ABFC). It lets the model
building method itself construct the basis functions necessary for
creating a model of arbitrary complexity with adequate predictive
performance. However, there are two issues that to some extent
plague the methods of both the subset selection and the ABFC,
especially when working with relatively small data samples: the
selection bias and the selection instability. We try to correct these
issues by model post-evaluation using Cross-Validation and model
ensembling. To evaluate the proposed method, we empirically
compare it to ABFC methods without ensembling, to a widely used
method of subset selection, as well as to some other well-known
regression modeling methods, using publicly available data sets.
Abstract: Due to the stringent legislation for emission of diesel
engines and also increasing demand on fuel consumption, the
importance of detailed 3D simulation of fuel injection, mixing and
combustion have been increased in the recent years. In the present
work, FIRE code has been used to study the detailed modeling of
spray and mixture formation in a Caterpillar heavy-duty diesel
engine. The paper provides an overview of the submodels
implemented, which account for liquid spray atomization, droplet
secondary break-up, droplet collision, impingement, turbulent
dispersion and evaporation. The simulation was performed from
intake valve closing (IVC) to exhaust valve opening (EVO). The
predicted in-cylinder pressure is validated by comparing with
existing experimental data. A good agreement between the predicted
and experimental values ensures the accuracy of the numerical
predictions collected with the present work. Predictions of engine
emissions were also performed and a good quantitative agreement
between measured and predicted NOx and soot emission data were
obtained with the use of the present Zeldowich mechanism and
Hiroyasu model. In addition, the results reported in this paper
illustrate that the numerical simulation can be one of the most
powerful and beneficial tools for the internal combustion engine
design, optimization and performance analysis.
Abstract: Modeling of the dynamic behavior and motion are
renewed interest in the improved tractive performance of an
intelligent air-cushion tracked vehicle (IACTV). This paper presents
a new dynamical model for the forces on the developed small scale
intelligent air-cushion tracked vehicle moving over swamp peat. The
air cushion system partially supports the 25 % of vehicle total weight
in order to make the vehicle ground contact pressure 7 kN/m2. As the
air-cushion support system can adjust automatically on the terrain, so
the vehicle can move over the terrain without any risks. The springdamper
system is used with the vehicle body to control the aircushion
support system on any undulating terrain by making the
system sinusoidal form. Experiments have been carried out to
investigate the relationships among tractive efficiency, slippage,
traction coefficient, load distribution ratio, tractive effort, motion
resistance and power consumption in given terrain conditions.
Experiment and simulation results show that air-cushion system
improves the vehicle performance by keeping traction coefficient of
71% and tractive efficiency of 62% and the developed model can
meet the demand of transport efficiency with the optimal power
consumption.
Abstract: Particle boards were prepared from Maize cob (MC) and urea-formaldehyde resin (UFR) on compression moulding machine. The amount of MC was varied from 50-120g while 30g of UFR was kept constant. Some mechanical properties of the particle boards were tested using the standard ASM methods. The results show that as the MC content increased from 50- 120g in 30g UFR, the hardness increased from about 6.89 x 102 to7.51 x 102MPa. Impact strength decreased from 3.3x 10-2 to 0.45 x 10-2J/M2, while tensile strength initially increased from 2.63 x 102 to 3.14 x 102 MPa as the MC increased from 50 to 60g in 30g UFR, thereafter, it decreased to about 1.35 x 102MPa at 120g in 30g content.
Abstract: In the Enhanced Oil Recovery (EOR) method, use of Carbon dioxide flooding whereby CO2 is injected into an oil reservoir to increase output when extracting oil resulted significant recovery worldwide. The carbon dioxide function as a pressurizing agent when mixed into the underground crude oil will reduce its viscosity and will enable a rapid oil flow. Despite the CO2’s advantage in the oil recovery, it may result to asphaltene precipitation a problem that will cause the reduction of oil produced from oil wells. In severe cases, asphaltene precipitation can cause costly blockages in oil pipes and machinery. This paper presents reviews of several studies done on mathematical modeling of asphaltene precipitation. The synthesized result from several researches done on this topic can be used as guide in order to better understand asphaltene precipitation. Likewise, this can be used as initial reference for students, and new researchers doing study on asphaltene precipitation.
Abstract: In this paper a stochastic scenario-based model predictive control applied to molten salt storage systems in concentrated solar tower power plant is presented. The main goal of this study is to build up a tool to analyze current and expected future resources for evaluating the weekly power to be advertised on electricity secondary market. This tool will allow plant operator to maximize profits while hedging the impact on the system of stochastic variables such as resources or sunlight shortage.
Solving the problem first requires a mixed logic dynamic modeling of the plant. The two stochastic variables, respectively the sunlight incoming energy and electricity demands from secondary market, are modeled by least square regression. Robustness is achieved by drawing a certain number of random variables realizations and applying the most restrictive one to the system. This scenario approach control technique provides the plant operator a confidence interval containing a given percentage of possible stochastic variable realizations in such a way that robust control is always achieved within its bounds. The results obtained from many trajectory simulations show the existence of a ‘’reliable’’ interval, which experimentally confirms the algorithm robustness.
Abstract: This paper addresses the problem of the partial state
feedback stabilization of a class of nonlinear systems. In order to
stabilization this class systems, the especial place of this paper is
to reverse designing the state feedback control law from the method
of judging system stability with the center manifold theory. First of
all, the center manifold theory is applied to discuss the stabilization
sufficient condition and design the stabilizing state control laws for a
class of nonlinear. Secondly, the problem of partial stabilization for a
class of plane nonlinear system is discuss using the lyapunov second
method and the center manifold theory. Thirdly, we investigate specially
the problem of the stabilization for a class of homogenous plane
nonlinear systems, a class of nonlinear with dual-zero eigenvalues and
a class of nonlinear with zero-center using the method of lyapunov
function with homogenous derivative, specifically. At the end of this
paper, some examples and simulation results are given show that the
approach of this paper to this class of nonlinear system is effective
and convenient.
Abstract: The damage tolerance behavior of integrally and
conventional stiffened panel is investigated based on the fracture
mechanics and finite element analysis. The load bearing capability
and crack growth characteristic of both types of the stiffened panels
having same configuration subjected to distributed tensile load is
examined in this paper. A fourteen-stringer stiffened panel is
analyzed for a central skin crack propagating towards the adjacent
stringers. Stress intensity factors and fatigue crack propagation rates
of both types of the stiffened panels are then compared. The analysis
results show that integral stiffening causes higher stress intensity
factor than conventional stiffened panel as the crack tip passes
through the stringer and the integrally stiffened panel has less load
bearing capability than the riveted stiffened panel.
Abstract: Based on Rayleigh beam theory, the sub-impacts of a
free-free beam struck horizontally by a round-nosed rigid mass is
simulated by the finite difference method and the impact-separation
conditions. In order to obtain the sub-impact force, a uniaxial
compression elastic-plastic contact model is employed to analyze the
local deformation field on contact zone. It is found that the horizontal
impact is a complicated process including the elastic plastic
sub-impacts in sequence. There are two sub-zones of sub-impact. In
addition, it found that the elastic energy of the free-free beam is more
suitable for the Poisson collision hypothesis to explain compression
and recovery processes.
Abstract: Predicting short term wind speed is essential in order
to prevent systems in-action from the effects of strong winds. It also
helps in using wind energy as an alternative source of energy, mainly
for Electrical power generation. Wind speed prediction has
applications in Military and civilian fields for air traffic control,
rocket launch, ship navigation etc. The wind speed in near future
depends on the values of other meteorological variables, such as
atmospheric pressure, moisture content, humidity, rainfall etc. The
values of these parameters are obtained from a nearest weather
station and are used to train various forms of neural networks. The
trained model of neural networks is validated using a similar set of
data. The model is then used to predict the wind speed, using the
same meteorological information. This paper reports an Artificial
Neural Network model for short term wind speed prediction, which
uses back propagation algorithm.
Abstract: For numerical prediction of the NOX in the exhaust of
a compression ignition engine a model was developed by considering
the parameter equivalence ratio. This model was validated by
comparing the predicted results of NOX with experimental ones. The
ultimate aim of the work was to access the applicability, robustness
and performance of the improved NOX model against other NOX
models.
Abstract: Wireless Sensor Networks (WSNs) are wireless
networks consisting of number of tiny, low cost and low power
sensor nodes to monitor various physical phenomena like
temperature, pressure, vibration, landslide detection, presence of any
object, etc. The major limitation in these networks is the use of nonrechargeable
battery having limited power supply. The main cause of
energy consumption WSN is communication subsystem. This paper
presents an efficient grid formation/clustering strategy known as Grid
based level Clustering and Aggregation of Data (GCAD). The
proposed clustering strategy is simple and scalable that uses low duty
cycle approach to keep non-CH nodes into sleep mode thus reducing
energy consumption. Simulation results demonstrate that our
proposed GCAD protocol performs better in various performance
metrics.