Abstract: This study investigated the seasonal prevalence of
Aedes aegypti and Ae. albopictus larvae in three topographical areas
(i.e. mangrove, rice paddy and mountainous areas). Samples were
collected from 300 households in both wet and dry seasons in nine
districts in Nakhon Si Thammarat province. Ae. aegypti and Ae.
albopictus were found in 21 out of 29 types of water containers in
mangrove, rice paddy and mountainous areas. Ae. aegypti and Ae.
albopictus laid eggs in different container types depending on season
and topographical areas. Ae. aegypti larvae were found most in metal
box in mangrove and mountainous areas in wet season. Ae.
albopictus larvae were also found most in metal box in mangrove and
mountainous areas in both wet and dry seasons. All Ae. albopictus
larval indices were higher than Ae. aegypti larval indices in all three
topographical areas and both seasons. HI and BI did not differ in
three topographical areas but differed between Aedes sp. HI for both
Ae. aegypti and Ae. albopictus in all three topographical areas in both
seasons were greater than 10 %, except Aedes aegypti in rice paddy
area in wet season. This indicated high risks of DHF transmission in
these areas.
Abstract: Short Message Service (SMS) has grown in
popularity over the years and it has become a common way of
communication, it is a service provided through General System
for Mobile Communications (GSM) that allows users to send text
messages to others.
SMS is usually used to transport unclassified information, but
with the rise of mobile commerce it has become a popular tool for
transmitting sensitive information between the business and its
clients. By default SMS does not guarantee confidentiality and
integrity to the message content.
In the mobile communication systems, security (encryption)
offered by the network operator only applies on the wireless link.
Data delivered through the mobile core network may not be
protected. Existing end-to-end security mechanisms are provided
at application level and typically based on public key
cryptosystem.
The main concern in a public-key setting is the authenticity of
the public key; this issue can be resolved by identity-based (IDbased)
cryptography where the public key of a user can be derived
from public information that uniquely identifies the user.
This paper presents an encryption mechanism based on the IDbased
scheme using Elliptic curves to provide end-to-end security
for SMS. This mechanism has been implemented over the standard
SMS network architecture and the encryption overhead has been
estimated and compared with RSA scheme. This study indicates
that the ID-based mechanism has advantages over the RSA
mechanism in key distribution and scalability of increasing
security level for mobile service.
Abstract: Quantum computation using qubits made of two component Bose-Einstein condensates (BECs) is analyzed. We construct a general framework for quantum algorithms to be executed using the collective states of the BECs. The use of BECs allows for an increase of energy scales via bosonic enhancement, resulting in two qubit gate operations that can be performed at a time reduced by a factor of N, where N is the number of bosons per qubit. We illustrate the scheme by an application to Deutsch-s and Grover-s algorithms, and discuss possible experimental implementations. Decoherence effects are analyzed under both general conditions and for the experimental implementation proposed.
Abstract: The study of a real function of two real variables can be supported by visualization using a Computer Algebra System (CAS). One type of constraints of the system is due to the algorithms implemented, yielding continuous approximations of the given function by interpolation. This often masks discontinuities of the function and can provide strange plots, not compatible with the mathematics. In recent years, point based geometry has gained increasing attention as an alternative surface representation, both for efficient rendering and for flexible geometry processing of complex surfaces. In this paper we present different artifacts created by mesh surfaces near discontinuities and propose a point based method that controls and reduces these artifacts. A least squares penalty method for an automatic generation of the mesh that controls the behavior of the chosen function is presented. The special feature of this method is the ability to improve the accuracy of the surface visualization near a set of interior points where the function may be discontinuous. The present method is formulated as a minimax problem and the non uniform mesh is generated using an iterative algorithm. Results show that for large poorly conditioned matrices, the new algorithm gives more accurate results than the classical preconditioned conjugate algorithm.
Abstract: In the Enhanced Oil Recovery (EOR) method, use of Carbon dioxide flooding whereby CO2 is injected into an oil reservoir to increase output when extracting oil resulted significant recovery worldwide. The carbon dioxide function as a pressurizing agent when mixed into the underground crude oil will reduce its viscosity and will enable a rapid oil flow. Despite the CO2’s advantage in the oil recovery, it may result to asphaltene precipitation a problem that will cause the reduction of oil produced from oil wells. In severe cases, asphaltene precipitation can cause costly blockages in oil pipes and machinery. This paper presents reviews of several studies done on mathematical modeling of asphaltene precipitation. The synthesized result from several researches done on this topic can be used as guide in order to better understand asphaltene precipitation. Likewise, this can be used as initial reference for students, and new researchers doing study on asphaltene precipitation.
Abstract: Average current analysis checking the impact of
current flow is very important to guarantee the reliability of
semiconductor systems. As semiconductor process technologies
improve, the coupling capacitance often become bigger than self
capacitances. In this paper, we propose an analytic technique for
analyzing average current on interconnects in multi-conductor
structures. The proposed technique has shown to yield the acceptable
errors compared to HSPICE results while providing computational
efficiency.
Abstract: The balanced Hamiltonian cycle problemis a quiet new topic of graph theorem. Given a graph G = (V, E), whose edge set can be partitioned into k dimensions, for positive integer k and a Hamiltonian cycle C on G. The set of all i-dimensional edge of C, which is a subset by E(C), is denoted as Ei(C).
Abstract: The Internet is the global data communications
infrastructure based on the interconnection of both public and private
networks using protocols that implement Internetworking on a global
scale. Hence the control of protocol and infrastructure development,
resource allocation and network operation are crucial and interlinked
aspects. Internet Governance is the hotly debated and contentious
subject that refers to the global control and operation of key Internet
infrastructure such as domain name servers and resources such as
domain names. It is impossible to separate technical and political
positions as they are interlinked. Furthermore the existence of a
global market, transparency and competition impact upon Internet
Governance and related topics such as network neutrality and
security. Current trends and developments regarding Internet
governance with a focus on the policy-making process, security and
control have been observed to evaluate current and future
implications on the Internet. The multi stakeholder approach to
Internet Governance discussed in this paper presents a number of
opportunities, issues and developments that will affect the future
direction of the Internet. Internet operation, maintenance and
advisory organisations such as the Internet Corporation for Assigned
Names and Numbers (ICANN) or the Internet Governance Forum
(IGF) are currently in the process of formulating policies for future
Internet Governance. Given the controversial nature of the issues at
stake and the current lack of agreement it is predicted that
institutional as well as market governance will remain present for the
network access and content.
Abstract: Fructooligosaccharides derived from microbial enzyme especially from fungal sources has been received particular attention due to its beneficial effects as prebiotics and mass production. However, fungal fermentation is always cumbersome due to its broth rheology problem that will eventually affect the production of FOS. This study investigated the efficiency of immobilized cell system using rotating fibrous bed bioreactor (RFBB) in producing fructooligosaccharides (FOS). A comparative picture with respect to conventional stirred tank bioreactor (CSTB) and RFBB has been presented. To demonstrate the effect of agitation intensity and aeration rate, a laboratory-scale bioreactor 2.5 L was operated in three phases (high, medium, low) for 48 hours. Agitation speed has a great influence on P. simplicissimum fermentation for FOS production, where the volumetric FOS productivity using RFBB is increased with almost 4 fold compared to the FOS productivity in CSTB that only 0.319 g/L/h. Rate of FOS production increased up to 1.2 fold when immobilized cells system was employed at aeration rate similar to the freely suspended cells at 2.0 vvm.
Abstract: Rice, which is the staple food in Sierra Leone, is
consumed on a daily basis. It is the most imperative food crop
extensively grown by farmers across all ecologies in the country.
Though much attention is now given to rice grain production through
the small holder commercialization programme (SHCP), however, no
attention has been given in investigating the limitations faced by rice
producers. This paper will contribute to attempts to overcome the
development challenges caused by food insecurity. The objective of
this paper is thus, to analysis the relationship between rice production
and the domestic retail price of rice. The study employed a log linear
model in which, the quantity of rice produced is the dependent
variable, quantity of rice imported, price of imported rice and price of
domestic rice as explanatory variables. Findings showed that, locally
produced rice is even more expensive than the imported rice per ton,
and almost all the inhabitants in the capital city which hosts about
65% of the entire population of the country favor imported rice, as it
is free from stones with other impurities. On the other hand, to
control price and simultaneously increase rice production, the
government should purchase the rice from the farmers and then sell to private retailers.
Abstract: The topic of surface flattening plays a vital role in the field of computer aided design and manufacture. Surface flattening enables the production of 2D patterns and it can be used in design and manufacturing for developing a 3D surface to a 2D platform, especially in fashion design. This study describes surface flattening based on minimum energy methods according to the property of different fabrics. Firstly, through the geometric feature of a 3D surface, the less transformed area can be flattened on a 2D platform by geodesic. Then, strain energy that has accumulated in mesh can be stably released by an approximate implicit method and revised error function. In some cases, cutting mesh to further release the energy is a common way to fix the situation and enhance the accuracy of the surface flattening, and this makes the obtained 2D pattern naturally generate significant cracks. When this methodology is applied to a 3D mannequin constructed with feature lines, it enhances the level of computer-aided fashion design. Besides, when different fabrics are applied to fashion design, it is necessary to revise the shape of a 2D pattern according to the properties of the fabric. With this model, the outline of 2D patterns can be revised by distributing the strain energy with different results according to different fabric properties. Finally, this research uses some common design cases to illustrate and verify the feasibility of this methodology.
Abstract: Sputum smear conversion after one month of antituberculosis
therapy in new smear positive pulmonary tuberculosis
patients (PTB+) is a vital indicator towards treatment success. The
objective of this study is to determine the rate of sputum smear
conversion in new PTB+ patients after one month under treatment of
National Institute of Diseases of the Chest and Hospital (NIDCH).
Analysis of sputum smear conversion was done by re-clinical
examination with sputum smear microscopic test after one month.
Socio-demographic and hematological parameters were evaluated to
perceive the correlation with the disease status. Among all enrolled
patients only 33.33% were available for follow up diagnosis and of
them only 42.86% patients turned to smear negative. Probably this
consequence is due to non-coherence to the proper disease
management. 66.67% and 78.78% patients reported low haemoglobin
and packed cell volume level respectively whereas 80% and 93.33%
patients accounted accelerated platelet count and erythrocyte
sedimentation rate correspondingly.
Abstract: Camera calibration is an indispensable step for augmented
reality or image guided applications where quantitative information
should be derived from the images. Usually, a camera
calibration is obtained by taking images of a special calibration object
and extracting the image coordinates of projected calibration marks
enabling the calculation of the projection from the 3d world coordinates
to the 2d image coordinates. Thus such a procedure exhibits
typical steps, including feature point localization in the acquired
images, camera model fitting, correction of distortion introduced by
the optics and finally an optimization of the model-s parameters. In
this paper we propose to extend this list by further step concerning
the identification of the optimal subset of images yielding the smallest
overall calibration error. For this, we present a Monte Carlo based
algorithm along with a deterministic extension that automatically
determines the images yielding an optimal calibration. Finally, we
present results proving that the calibration can be significantly
improved by automated image selection.
Abstract: This paper presents a novel two-phase hybrid optimization algorithm with hybrid genetic operators to solve the optimal control problem of a single stage hybrid manufacturing system. The proposed hybrid real coded genetic algorithm (HRCGA) is developed in such a way that a simple real coded GA acts as a base level search, which makes a quick decision to direct the search towards the optimal region, and a local search method is next employed to do fine tuning. The hybrid genetic operators involved in the proposed algorithm improve both the quality of the solution and convergence speed. The phase–1 uses conventional real coded genetic algorithm (RCGA), while optimisation by direct search and systematic reduction of the size of search region is employed in the phase – 2. A typical numerical example of an optimal control problem with the number of jobs varying from 10 to 50 is included to illustrate the efficacy of the proposed algorithm. Several statistical analyses are done to compare the validity of the proposed algorithm with the conventional RCGA and PSO techniques. Hypothesis t – test and analysis of variance (ANOVA) test are also carried out to validate the effectiveness of the proposed algorithm. The results clearly demonstrate that the proposed algorithm not only improves the quality but also is more efficient in converging to the optimal value faster. They can outperform the conventional real coded GA (RCGA) and the efficient particle swarm optimisation (PSO) algorithm in quality of the optimal solution and also in terms of convergence to the actual optimum value.
Abstract: In this paper an effective approach for segmenting
human skin regions in images taken at different environment is
proposed. The proposed method uses a color distance map that is
flexible enough to reliably detect the skin regions even if the
illumination conditions of the image vary. Local image conditions is
also focused, which help the technique to adaptively detect differently
illuminated skin regions of an image. Moreover, usage of local
information also helps the skin detection process to get rid of picking
up much noisy pixels.
Abstract: This study investigated the number of Aedes larvae,
the key breeding sites of Aedes sp., and the relationship between
climatic factors and the incidence of DHF in Samui Islands. We
conducted our questionnaire and larval surveys from randomly
selected 105 households in Samui Islands in July-September 2006.
Pearson-s correlation coefficient was used to explore the primary
association between the DHF incidence and all climatic factors.
Multiple stepwise regression technique was then used to fit the
statistical model. The results showed that the positive indoor
containers were small jars, cement tanks, and plastic tanks. The
positive outdoor containers were small jars, cement tanks, plastic
tanks, used cans, tires, plastic bottles, discarded objects, pot saucers,
plant pots, and areca husks. All Ae. albopictus larval indices (i.e., CI,
HI, and BI) were higher than Ae. aegypti larval indices in this area.
These larval indices were higher than WHO standard. This indicated
a high risk of DHF transmission at Samui Islands. The multiple
stepwise regression model was y = –288.80 + 11.024xmean temp. The
mean temperature was positively associated with the DHF incidence
in this area.
Abstract: In this paper, a plane-strain orthotropic elasto-plastic
dynamic constitutive model is established, and with this constitutive
model, the thermal shock wave induced by intense pulsed X-ray
radiation in cylinder shell composite is simulated by the finite element
code, then the properties of thermal shock wave propagation are
discussed. The results show that the thermal shock wave exhibit
different shapes under the radiation of soft and hard X-ray, and while
the composite is radiated along different principal axes, great
differences exist in some aspects, such as attenuation of the peak stress
value, spallation and so on.
Abstract: This paper presents a generalized formulation for the
problem of buckling optimization of anisotropic, radially graded,
thin-walled, long cylinders subject to external hydrostatic pressure.
The main structure to be analyzed is built of multi-angle fibrous
laminated composite lay-ups having different volume fractions of the
constituent materials within the individual plies. This yield to a
piecewise grading of the material in the radial direction; that is the
physical and mechanical properties of the composite material are
allowed to vary radially. The objective function is measured by
maximizing the critical buckling pressure while preserving the total
structural mass at a constant value equals to that of a baseline
reference design. In the selection of the significant optimization
variables, the fiber volume fractions adjoin the standard design
variables including fiber orientation angles and ply thicknesses. The
mathematical formulation employs the classical lamination theory,
where an analytical solution that accounts for the effective axial and
flexural stiffness separately as well as the inclusion of the coupling
stiffness terms is presented. The proposed model deals with
dimensionless quantities in order to be valid for thin shells having
arbitrary thickness-to-radius ratios. The critical buckling pressure
level curves augmented with the mass equality constraint are given
for several types of cylinders showing the functional dependence of
the constrained objective function on the selected design variables. It
was shown that material grading can have significant contribution to
the whole optimization process in achieving the required structural
designs with enhanced stability limits.
Abstract: The mosaicing technique has been employed in more and more application fields, from entertainment to scientific ones. In the latter case, often the final evaluation is still left to human beings, that assess visually the quality of the mosaic. Many times, a lack of objective measurements in microscopic mosaicing may prevent the mosaic from being used as a starting image for further analysis. In this work we analyze three different metrics and indexes, in the domain of signal analysis, image analysis and visual quality, to measure the quality of different aspects of the mosaicing procedure, such as registration errors and visual quality. As the case study we consider the mosaicing algorithm we developed. The experiments have been carried out by considering mosaics with very different features: histological samples, that are made of detailed and contrasted images, and live stem cells, that show a very low contrast and low detail levels.
Abstract: The Taiwan government has started to promote the “Plain Landscape Afforestation and Greening Program" since 2002. A key task of the program was the payment for environmental services (PES), entitled the “Plain Landscape Afforestation Policy" (PLAP), which was certificated by the Executive Yuan on August 31, 2001 and enacted on January 1, 2002. According to the policy, it is estimated that the total area of afforestation will be 25,100 hectares by December 31, 2007. Until the end of 2007, the policy had been enacted for six years in total and the actual area of afforestation was 8,919.18 hectares. Among them, Taiwan Sugar Corporation (TSC) was accounted for 7,960 hectares (with 2,450.83 hectares as public service area) which occupied 86.22% of the total afforestation area; the private farmland promoted by local governments was accounted for 869.18 hectares which occupied 9.75% of the total afforestation area. Based on the above, we observe that most of the afforestation area in this policy is executed by TSC, and the achievement ratio by TSC is better than by others. It implies that the success of the PLAP is seriously related to the execution of TSC. The objective of this study is to analyze the relevant policy planning of TSC-s participation in the PLAP, suggest complementary measures, and draw up effective adjustment mechanisms, so as to improve the effectiveness of executing the policy. Our main conclusions and suggestions are summarized as follows: 1. The main reason for TSC-s participation in the PLAP is based on their passive cooperation with the central government or company policy. Prior to TSC-s participation in the PLAP, their lands were mainly used for growing sugarcane. 2. The main factors of TSC-s consideration on the selection of tree species are based on the suitability of land and species. The largest proportion of tree species is allocated to economic forests, and the lack of technical instruction was the main problem during afforestation. Moreover, the method of improving TSC-s future development in leisure agriculture and landscape business becomes a key topic. 3. TSC has developed short and long-term plans on participating in the PLAP for the future. However, there is no great willingness or incentive on budgeting for such detailed planning. 4. Most people from TSC interviewed consider the requirements on PLAP unreasonable. Among them, an unreasonable requirement on the number of trees accounted for the greatest proportion; furthermore, most interviewees suggested that the government should continue to provide incentives even after 20 years. 5. Since the government shares the same goals as TSC, there should be sufficient cooperation and communication that support the technical instruction and reduction of afforestation cost, which will also help to improve effectiveness of the policy.