Abstract: Actual load, material characteristics and other
quantities often differ from the design values. This can cause worse
function, shorter life or failure of a civil engineering structure, a
machine, vehicle or another appliance. The paper shows main causes
of the uncertainties and deviations and presents a systematic
approach and efficient tools for their elimination or mitigation of
consequences. Emphasis is put on the design stage, which is most
important for reliability ensuring. Principles of robust design and
important tools are explained, including FMEA, sensitivity analysis
and probabilistic simulation methods. The lifetime prediction of
long-life objects can be improved by long-term monitoring of the
load response and damage accumulation in operation. The condition
evaluation of engineering structures, such as bridges, is often based
on visual inspection and verbal description. Here, methods based on
fuzzy logic can reduce the subjective influences.
Abstract: In the last few years, three multivariate spectral
analysis techniques namely, Principal Component Analysis (PCA),
Independent Component Analysis (ICA) and Non-negative Matrix
Factorization (NMF) have emerged as effective tools for oscillation
detection and isolation. While the first method is used in determining
the number of oscillatory sources, the latter two methods
are used to identify source signatures by formulating the detection
problem as a source identification problem in the spectral domain.
In this paper, we present a critical drawback of the underlying linear
(mixing) model which strongly limits the ability of the associated
source separation methods to determine the number of sources
and/or identify the physical source signatures. It is shown that the
assumed mixing model is only valid if each unit of the process gives
equal weighting (all-pass filter) to all oscillatory components in its
inputs. This is in contrast to the fact that each unit, in general, acts
as a filter with non-uniform frequency response. Thus, the model
can only facilitate correct identification of a source with a single
frequency component, which is again unrealistic. To overcome
this deficiency, an iterative post-processing algorithm that correctly
identifies the physical source(s) is developed. An additional issue
with the existing methods is that they lack a procedure to pre-screen
non-oscillatory/noisy measurements which obscure the identification
of oscillatory sources. In this regard, a pre-screening procedure
is prescribed based on the notion of sparseness index to eliminate
the noisy and non-oscillatory measurements from the data set used
for analysis.
Abstract: Development of cities and villages, agricultural farms
and industrial regions in abutment and/or in the course of streams and
rivers or in prone flood lands has been caused more notations in
hydrology problems and city planning topics. In order to protection
of cities against of flood damages, embankment construction is a
desired and scientific method. The cities that located in arid zones
may damage by floods periodically. Zavvareh city in Ardestan
township(Isfahan province) with 7704 people located in Ardestan
plain that has been damaged by floods that have flowed from
dominant mountainous watersheds in past years with regard to return
period. In this study, according to flowed floods toward Zavvareh
city, was attempt to plan suitable hydraulic structures such as canals,
bridges and collectors in order to collection, conduction and
depletion of city surface runoff.
Abstract: To help the client to select a competent agent
construction enterprise (ACE), this study aims to investigate the
selection standards by using the Fuzzy Analytic Hierarchy Process
(FAHP) and build an evaluation mathematical model with Grey
Relational Analysis (GRA). According to the outputs of literature
review, four orderly levels are established within the model, taking the
consideration of various agent construction models in practice. Then,
the process of applying FAHP and GRA is discussed in detailed.
Finally, through a case study, this paper illustrates how to apply these
methods in getting the weights of each standard and the final
assessment result.
Abstract: The increasing influence of traffic on building
objects and people residing in them should be taken into account in
diagnosis and design. Users of buildings expect that vibrations
occurring in their environment, will not only lead to damage to the
building or its accelerated wear, but neither would affect the required
comfort in rooms designed to accommodate people. This article
describes the methods and principles useful in designing and building
diagnostics located near transportation routes, with particular
emphasis on the impact of traffic vibration on people in buildings. It
also describes the procedures used in obtaining information about the
parameters of vibrations in different cases of diagnostics and design.
A universal algorithm of procedure in diagnostics and design of
buildings taking into account assurance of human vibration comfort
of people residing in the these buildings was presented.
Abstract: Selection of a project among a set of possible
alternatives is a difficult task that the decision maker (DM) has to
face. In this paper, by using a fuzzy TOPSIS technique we propose a
new method for a project selection problem. After reviewing four
common methods of comparing investment alternatives (net present
value, rate of return, benefit cost analysis and payback period) we
use them as criteria in a TOPSIS technique. First we calculate the
weight of each criterion by a pairwise comparison and then we utilize
the improved TOPSIS assessment for the project selection.
Abstract: Fast delay estimation methods, as opposed to
simulation techniques, are needed for incremental performance
driven layout synthesis. On-chip inductive effects are becoming
predominant in deep submicron interconnects due to increasing clock
speed and circuit complexity. Inductance causes noise in signal
waveforms, which can adversely affect the performance of the circuit
and signal integrity. Several approaches have been put forward which
consider the inductance for on-chip interconnect modelling. But for
even much higher frequency, of the order of few GHz, the shunt
dielectric lossy component has become comparable to that of other
electrical parameters for high speed VLSI design. In order to cope up
with this effect, on-chip interconnect has to be modelled as
distributed RLCG line. Elmore delay based methods, although
efficient, cannot accurately estimate the delay for RLCG interconnect
line. In this paper, an accurate analytical delay model has been
derived, based on first and second moments of RLCG
interconnection lines. The proposed model considers both the effect
of inductance and conductance matrices. We have performed the
simulation in 0.18μm technology node and an error of as low as less
as 5% has been achieved with the proposed model when compared to
SPICE. The importance of the conductance matrices in interconnect
modelling has also been discussed and it is shown that if G is
neglected for interconnect line modelling, then it will result an delay
error of as high as 6% when compared to SPICE.
Abstract: This paper investigates the inverse problem of determining
the unknown time-dependent leading coefficient in the parabolic
equation using the usual conditions of the direct problem and an additional
condition. An algorithm is developed for solving numerically
the inverse problem using the technique of space decomposition in a
reproducing kernel space. The leading coefficients can be solved by a
lower triangular linear system. Numerical experiments are presented
to show the efficiency of the proposed methods.
Abstract: The morphological parameter of a thin film surface
can be characterized by power spectral density (PSD) functions
which provides a better description to the topography than the RMS
roughness and imparts several useful information of the surface
including fractal and superstructure contributions. Through the
present study Nanoparticle copper/carbon composite films were
prepared by co-deposition of RF-Sputtering and RF-PECVD method
from acetylene gas and copper target. Surface morphology of thin
films is characterized by using atomic force microscopy (AFM). The
Carbon content of our films was obtained by Rutherford Back
Scattering (RBS) and it varied from .4% to 78%. The power values of
power spectral density (PSD) for the AFM data were determined by
the fast Fourier transform (FFT) algorithms. We investigate the effect
of carbon on the roughness of thin films surface. Using such
information, roughness contributions of the surface have been
successfully extracted.