Abstract: Over a million tonnes of cigarette butts (CBs) are produced worldwide annually. These CBs accumulate in the environment due to the poor biodegradability of the cellulose acetate filters and pose a serious environmental risk. This paper presents some of the results from a continuing study on recycling CBs into fired clay bricks. Properties including compressive strength, flexural strength, density, water absorption and thermal conductivity of fired clay bricks are reported and discussed. Furthermore, leaching of heavy metals from the manufactured clay bricks was tested. The results show that the density of fired bricks was reduced by about 8 – 30 %, depending on the percentage of CBs incorporated into the raw materials. The compressive strength of bricks tested was 12.57, 5.22 and 3.00 MPa for 2.5, 5.0 and 10 % CB content respectively. Water absorption and initial rate of absorption values increased as density, and hence porosity, of bricks decreased with increasing CB volume. The leaching test results revealed trace amounts of heavy metals.
Abstract: Contour filter strips planted with perennial vegetation
can be used to improve surface and ground water quality by reducing
pollutant, such as NO3-N, and sediment outflow from cropland to a
river or lake. Meanwhile, the filter strips of perennial grass with biofuel
potentials also have economic benefits of producing ethanol. In
this study, The Soil and Water Assessment Tool (SWAT) model was
applied to the Walnut Creek Watershed to examine the effectiveness
of contour strips in reducing NO3-N outflows from crop fields to the
river or lake. Required input data include watershed topography,
slope, soil type, land-use, management practices in the watershed and
climate parameters (precipitation, maximum/minimum air
temperature, solar radiation, wind speed and relative humidity).
Numerical experiments were conducted to identify potential
subbasins in the watershed that have high water quality impact, and
to examine the effects of strip size and location on NO3-N reduction
in the subbasins under various meteorological conditions (dry,
average and wet). Variable sizes of contour strips (10%, 20%, 30%
and 50%, respectively, of a subbasin area) planted with perennial
switchgrass were selected for simulating the effects of strip size and
location on stream water quality. Simulation results showed that a
filter strip having 10%-50% of the subbasin area could lead to 55%-
90% NO3-N reduction in the subbasin during an average rainfall
year. Strips occupying 10-20% of the subbasin area were found to be
more efficient in reducing NO3-N when placed along the contour
than that when placed along the river. The results of this study can
assist in cost-benefit analysis and decision-making in best water
resources management practices for environmental protection.
Abstract: Neural networks offer an alternative approach both
for identification and control of nonlinear processes in process
engineering. The lack of software tools for the design of controllers
based on neural network models is particularly pronounced in this
field. SIMULINK is properly a widely used graphical code
development environment which allows system-level developers to
perform rapid prototyping and testing. Such graphical based
programming environment involves block-based code development
and offers a more intuitive approach to modeling and control task in
a great variety of engineering disciplines. In this paper a
SIMULINK based Neural Tool has been developed for analysis and
design of multivariable neural based control systems. This tool has
been applied to the control of a high purity distillation column
including non linear hydrodynamic effects. The proposed control
scheme offers an optimal response for both theoretical and practical
challenges posed in process control task, in particular when both,
the quality improvement of distillation products and the operation
efficiency in economical terms are considered.
Abstract: This article presents a voltage-mode universal
biquadratic filter performing simultaneous 3 standard functions: lowpass,
high-pass and band-pass functions, employing differential
different current conveyor (DDCC) and current controlled current
conveyor (CCCII) as active element. The features of the circuit are
that: the quality factor and pole frequency can be tuned independently
via the input bias currents: the circuit description is very simple,
consisting of 1 DDCC, 2 CCCIIs, 2 electronic resistors and 2
grounded capacitors. Without requiring component matching
conditions, the proposed circuit is very appropriate to further develop
into an integrated circuit. The PSPICE simulation results are
depicted. The given results agree well with the theoretical
anticipation.
Abstract: The expansive nature of soils containing high
amounts of clay minerals can be altered through chemical
stabilization, resulting in a material suitable for construction
purposes. The primary objective of this investigation was to
study the changes induced in the molecular structure of
phosphoric acid stabilized bentonite and lateritic soil using
Nuclear Magnetic Resonance (NMR) and Fourier Transform
Infrared (FTIR) spectroscopy. Based on the obtained data, it
was found that a surface alteration mechanism was the main
reason responsible for the improvement of treated soils.
Furthermore, the results indicated that the Al present in the
octahedral layer of clay minerals were more amenable to
chemical attacks and also partly responsible for the formation
of new products.
Abstract: In this paper, we present an analytical framework for the evaluation of the uplink performance of multihop cellular networks based on dynamic time division duplex (TDD). New wireless broadband protocols, such as WiMAX, WiBro, and 3G-LTE apply TDD, and mobile communication protocols under standardization (e.g., IEEE802.16j) are investigating mobile multihop relay (MMR) as a future technology. In this paper a novel MMR TDD scheme is presented, where the dynamic range of the frame is shared to traffic resources of asymmetric nature and multihop relaying. The mobile communication channel interference model comprises of inner and co-channel interference (CCI). The performance analysis focuses on the uplink due to the fact that the effects of dynamic resource allocation show significant performance degradation only in the uplink compared to time division multiple access (TDMA) schemes due to CCI [1-3], where the downlink results to be the same or better.The analysis was based on the signal to interference power ratio (SIR) outage probability of dynamic TDD (D-TDD) and TDMA systems,which are the most widespread mobile communication multi-user control techniques. This paper presents the uplink SIR outage probability with multihop results and shows that the dynamic TDD scheme applying MMR can provide a performance improvement compared to single hop applications if executed properly.
Abstract: This paper presents a fast and efficient on-line technique for estimating impedance of unbalanced loads in power systems. The proposed technique is an application of a discrete timedynamic filter based on stochastic estimation theory which is suitable for estimating parameters in noisy environment. The algorithm uses sets of digital samples of the distorted voltage and current waveforms of the non-linear load to estimate the harmonic contents of these two signal. The non-linear load impedance is then calculated from these contents. The method is tested using practical data. Results are reported and compared with those obtained using the conventional least error squares technique. In addition to the very accurate results obtained, the method can detect and reject bad measurements. This can be considered as a very important advantage over the conventional static estimation methods such as the least error square method.
Abstract: Four design alternatives for lateral force-resisting
systems of tall buildings in Dubai, UAE are presented. Quantitative
comparisons between the different designs are also made. This paper
is intended to provide different feasible lateral systems to be used in
Dubai in light of the available seismic hazard studies of the UAE.
The different lateral systems are chosen in conformance with the
International Building Code (IBC). Moreover, the expected behavior
of each system is highlighted and light is shed on some of the cost
implications associated with lateral system selection.
Abstract: It is well known that Logistic Regression is the gold
standard method for predicting clinical outcome, especially
predicting risk of mortality. In this paper, the Decision Tree method
has been proposed to solve specific problems that commonly use
Logistic Regression as a solution. The Biochemistry and
Haematology Outcome Model (BHOM) dataset obtained from
Portsmouth NHS Hospital from 1 January to 31 December 2001 was
divided into four subsets. One subset of training data was used to
generate a model, and the model obtained was then applied to three
testing datasets. The performance of each model from both methods
was then compared using calibration (the χ2 test or chi-test) and
discrimination (area under ROC curve or c-index). The experiment
presented that both methods have reasonable results in the case of the
c-index. However, in some cases the calibration value (χ2) obtained
quite a high result. After conducting experiments and investigating
the advantages and disadvantages of each method, we can conclude
that Decision Trees can be seen as a worthy alternative to Logistic
Regression in the area of Data Mining.
Abstract: Urban road network traffic has become one of the
most studied research topics in the last decades. This is mainly due to
the enlargement of the cities and the growing number of motor
vehicles traveling in this road network. One of the most sensitive
problems is to verify if the network is congestion-free. Another
related problem is the automatic reconfiguration of the network
without building new roads to alleviate congestions. These problems
require an accurate model of the traffic to determine the steady state
of the system. An alternative is to simulate the traffic to see if there
are congestions and when and where they occur. One key issue is to
find an adequate model for road intersections. Once the model
established, either a large scale model is built or the intersection is
represented by its performance measures and simulation for analysis.
In both cases, it is important to seek the queueing model to represent
the road intersection. In this paper, we propose to model the road
intersection as a BCMP queueing network and we compare this
analytical model against a simulation model for validation.
Abstract: Prostate cancer is one of the most frequent cancers in men and is a major cause of mortality in the most of countries. In many diagnostic and treatment procedures for prostate disease accurate detection of prostate boundaries in transrectal ultrasound (TRUS) images is required. This is a challenging and difficult task due to weak prostate boundaries, speckle noise and the short range of gray levels. In this paper a novel method for automatic prostate segmentation in TRUS images is presented. This method involves preprocessing (edge preserving noise reduction and smoothing) and prostate segmentation. The speckle reduction has been achieved by using stick filter and top-hat transform has been implemented for smoothing. A feed forward neural network and local binary pattern together have been use to find a point inside prostate object. Finally the boundary of prostate is extracted by the inside point and an active contour algorithm. A numbers of experiments are conducted to validate this method and results showed that this new algorithm extracted the prostate boundary with MSE less than 4.6% relative to boundary provided manually by physicians.
Abstract: This paper presents a novel control strategy of a threephase
four-wire Unified Power Quality (UPQC) for an improvement
in power quality. The UPQC is realized by integration of series and
shunt active power filters (APFs) sharing a common dc bus capacitor.
The shunt APF is realized using a thee-phase, four leg voltage source
inverter (VSI) and the series APF is realized using a three-phase,
three leg VSI. A control technique based on unit vector template
technique (UTT) is used to get the reference signals for series APF,
while instantaneous sequence component theory (ISCT) is used for
the control of Shunt APF. The performance of the implemented
control algorithm is evaluated in terms of power-factor correction,
load balancing, neutral source current mitigation and mitigation of
voltage and current harmonics, voltage sag and swell in a three-phase
four-wire distribution system for different combination of linear and
non-linear loads. In this proposed control scheme of UPQC, the
current/voltage control is applied over the fundamental supply
currents/voltages instead of fast changing APFs currents/voltages,
there by reducing the computational delay and the required sensors.
MATLAB/Simulink based simulations are obtained, which support
the functionality of the UPQC. MATLAB/Simulink based
simulations are obtained, which support the functionality of the
UPQC.
Abstract: According as the Architecture, Engineering and Construction (AEC) Industry projects have grown more complex and larger, the number of utilization of BIM for 3D design and simulation is increasing significantly. Therefore, typical applications of BIM such as clash detection and alternative measures based on 3-dimenstional planning are expanded to process management, cost and quantity management, structural analysis, check for regulation, and various domains for virtual design and construction. Presently, commercial BIM software is operated on single-user environment, so initial cost is so high and the investment may be wasted frequently. Cloud computing that is a next-generation internet technology enables simple internet devices (such as PC, Tablet, Smart phone etc) to use services and resources of BIM software. In this paper, we suggested developing method of the BIM software based on cloud computing environment in order to expand utilization of BIM and reduce cost of BIM software. First, for the benchmarking, we surveyed successful case of BIM and cloud computing. And we analyzed needs and opportunities of BIM and cloud computing in AEC Industry. Finally, we suggested main functions of BIM software based on cloud computing environment and developed a simple prototype of cloud computing BIM software for basic BIM model viewing.
Abstract: Biodiesel as an alternative fuel for diesel engines has been developed for some three decades now. While it is gaining wide acceptance in Europe, USA and some parts of Asia, the same cannot be said of Africa. With more than 35 countries in the continent depending on imported crude oil, it is necessary to look for alternative fuels which can be produced from resources available locally within any country. Hence this study presents performance of single cylinder diesel engine using blends of shea butter biodiesel. Shea butter was transformed into biodiesel by transesterification process. Tests are conducted to compare the biodiesel with baseline diesel fuel in terms of engine performance and exhaust emission characteristics. The results obtained showed that the addition of biodiesel to diesel fuel decreases the brake thermal efficiency (BTE) and increases the brake specific fuel consumption (BSFC). These results are expected due to the lower energy content of biodiesel fuel. On the other hand while the NOx emissions increased with increase in biodiesel content in the fuel blends, the emissions of carbon monoxide (CO), un-burnt hydrocarbon (UHC) and smoke opacity decreased. The engine performance which indicates that the biodiesel has properties and characteristics similar to diesel fuel and the reductions in exhaust emissions make shea butter biodiesel a viable additive or substitute to diesel fuel.
Abstract: It is well known that during the developments in the
economic sector and through the financial crises occur everywhere in
the whole world, volatility measurement is the most important
concept in financial time series. Therefore in this paper we discuss
the volatility for Amman stocks market (Jordan) for certain period of
time. Since wavelet transform is one of the most famous filtering
methods and grows up very quickly in the last decade, we compare
this method with the traditional technique, Fast Fourier transform to
decide the best method for analyzing the volatility. The comparison
will be done on some of the statistical properties by using Matlab
program.
Abstract: A high-frequency low-power sinusoidal quadrature
oscillator is presented through the use of two 2nd-order low-pass
current-mirror (CM)-based filters, a 1st-order CM low-pass filter and
a CM bilinear transfer function. The technique is relatively simple
based on (i) inherent time constants of current mirrors, i.e. the
internal capacitances and the transconductance of a diode-connected
NMOS, (ii) a simple negative resistance RN formed by a resistor load
RL of a current mirror. Neither external capacitances nor inductances
are required. As a particular example, a 1.9-GHz, 0.45-mW, 2-V
CMOS low-pass-filter-based all-current-mirror sinusoidal quadrature
oscillator is demonstrated. The oscillation frequency (f0) is 1.9 GHz
and is current-tunable over a range of 370 MHz or 21.6 %. The
power consumption is at approximately 0.45 mW. The amplitude
matching and the quadrature phase matching are better than 0.05 dB
and 0.15°, respectively. Total harmonic distortions (THD) are less
than 0.3 %. At 2 MHz offset from the 1.9 GHz, the carrier to noise
ratio (CNR) is 90.01 dBc/Hz whilst the figure of merit called a
normalized carrier-to-noise ratio (CNRnorm) is 153.03 dBc/Hz. The
ratio of the oscillation frequency (f0) to the unity-gain frequency (fT)
of a transistor is 0.25. Comparisons to other approaches are also
included.
Abstract: The financial crisis has decreased the opportunities of
small businesses to acquire financing through conventional financial
actors, such as commercial banks. This credit constraint is partly the
reason for the emergence of new alternatives of financing, in addition
to the spreading opportunities for communication and secure
financial transfer through Internet. One of the most interesting venues
for finance is termed “crowdfunding". As the term suggests
crowdfunding is an appeal to prospective customers and investors to
form a crowd that will finance projects that otherwise would find it
hard to generate support through the most common financial actors.
Crowdfunding is in this paper divided into different models; the
threshold model, the microfinance model, the micro loan model and
the equity model. All these models add to the financial possibilities of
emerging entrepreneurs.
Abstract: This paper presents an algorithm for the recognition
and tracking of moving objects, 1/10 scale model car is used to verify
performance of the algorithm. Presented algorithm for the recognition
and tracking of moving objects in the paper is as follows. SURF
algorithm is merged with Lucas-Kanade algorithm. SURF algorithm
has strong performance on contrast, size, rotation changes and it
recognizes objects but it is slow due to many computational
complexities. Processing speed of Lucas-Kanade algorithm is fast but
the recognition of objects is impossible. Its optical flow compares the
previous and current frames so that can track the movement of a pixel.
The fusion algorithm is created in order to solve problems which
occurred using the Kalman Filter to estimate the position and the
accumulated error compensation algorithm was implemented. Kalman
filter is used to create presented algorithm to complement problems
that is occurred when fusion two algorithms. Kalman filter is used to
estimate next location, compensate for the accumulated error. The
resolution of the camera (Vision Sensor) is fixed to be 640x480. To
verify the performance of the fusion algorithm, test is compared to
SURF algorithm under three situations, driving straight, curve, and
recognizing cars behind the obstacles. Situation similar to the actual is
possible using a model vehicle. Proposed fusion algorithm showed
superior performance and accuracy than the existing object
recognition and tracking algorithms. We will improve the performance
of the algorithm, so that you can experiment with the images of the
actual road environment.
Abstract: Median filter is widely used to remove impulse noise
without blurring sharp edges. However, when noise level increased,
or with thin edges, median filter may work poorly. This paper
proposes a new filter, which will detect edges along four possible
directions, and then replace noise corrupted pixel with estimated
noise-free edge median value. Simulations show that the proposed
multi-stage directional median filter can provide excellent
performance of suppressing impulse noise in all situations.
Abstract: In this article, by using fuzzy AHP and TOPSIS
technique we propose a new method for project selection problem.
After reviewing four common methods of comparing alternatives
investment (net present value, rate of return, benefit cost analysis
and payback period) we use them as criteria in AHP tree. In this
methodology by utilizing improved Analytical Hierarchy Process
by Fuzzy set theory, first we try to calculate weight of each
criterion. Then by implementing TOPSIS algorithm, assessment of
projects has been done. Obtained results have been tested in a
numerical example.