Abstract: This paper discusses the implementation of the Kalman
Filter along with the Global Positioning System (GPS) for indoor
robot navigation. Two dimensional coordinates is used for the map
building, and refers to the global coordinate which is attached to the
reference landmark for position and direction information the robot
gets. The Discrete Kalman Filter is used to estimate the robot position,
project the estimated current state ahead in time through time update
and adjust the projected estimated state by an actual measurement at
that time via the measurement update. The navigation test has been
performed and has been found to be robust.
Abstract: Study on suppression of interference in time domain equalizers is attempted for high data rate impulse radio (IR) ultra wideband communication system. The narrow band systems may cause interference with UWB devices as it is having very low transmission power and the large bandwidth. SRAKE receiver improves system performance by equalizing signals from different paths. This enables the use of SRAKE receiver techniques in IRUWB systems. But Rake receiver alone fails to suppress narrowband interference (NBI). A hybrid SRake-MMSE time domain equalizer is proposed to overcome this by taking into account both the effect of the number of rake fingers and equalizer taps. It also combats intersymbol interference. A semi analytical approach and Monte-Carlo simulation are used to investigate the BER performance of SRAKEMMSE receiver on IEEE 802.15.3a UWB channel models. Study on non-line of sight indoor channel models (both CM3 and CM4) illustrates that bit error rate performance of SRake-MMSE receiver with NBI performs better than that of Rake receiver without NBI. We show that for a MMSE equalizer operating at high SNR-s the number of equalizer taps plays a more significant role in suppressing interference.
Abstract: In recent years, Radio Frequency Identification (RFID)
is followed with interest by many researches, especially for the
purpose of indoor positioning as the innate properties of RFID are
profitable for achieving it. A lot of algorithms or schemes are proposed
to be used in the RFID-based positioning system, but most of them are
lack of environmental consideration and it induces inaccuracy of
application. In this research, a lot of algorithms and schemes of RFID
indoor positioning are discussed to see whether effective or not on
application, and some rules are summarized for achieving accurate
positioning. On the other hand, a new term “Noise Factor" is involved
to describe the signal loss between the target and the obstacle. As a
result, experimental data can be obtained but not only simulation; and
the performance of the positioning system can be expressed
substantially.
Abstract: In this paper, a multi-branch power line is modeled using ABCD matrix to show its worth as a communication channel. The model is simulated using MATLAB in an effort to investigate the effects of multiple loading, multipath, and those as a result of load mismatching. The channel transfer function is obtained and investigated using different cable lengths, and different number of bridge taps under given loading conditions.
Abstract: The heat storage capacity of concrete in building shells is a major reason for excessively large electricity consumption induced by indoor air conditioning. In this research, the previously developed Smart Temperature Information Material (STIM) is embedded in two groups of exterior wall specimens (the control group contains reinforced concrete exterior walls and the experimental group consists of tiled exterior walls). Long term temperature measurements within the concrete are taken by the embedded STIM. Temperature differences between the control group and the experimental group in walls facing the four cardinal directions (east, west, south, and north) are evaluated. This study aims to provide a basic reference for the design of exterior walls and the selection of heat insulation materials.
Abstract: A fast adaptive Tomlinson Harashima (T-H) precoder structure is presented for indoor wireless communications, where the channel may vary due to rotation and small movement of the mobile terminal. A frequency-selective slow fading channel which is time-invariant over a frame is assumed. In this adaptive T-H precoder, feedback coefficients are updated at the end of every uplink frame by using system identification technique for channel estimation in contrary with the conventional T-H precoding concept where the channel is estimated during the starting of the uplink frame via Wiener solution. In conventional T-H precoder it is assumed the channel is time-invariant in both uplink and downlink frames. However assuming the channel is time-invariant over only one frame instead of two, the proposed adaptive T-H precoder yields better performance than conventional T-H precoder if the channel is varied in uplink after receiving the training sequence.
Abstract: Continuous measurements and multivariate methods are applied in researching the effects of energy consumption on indoor air quality (IAQ) in a Finnish one-family house. Measured data used in this study was collected continuously in a house in Kuopio, Eastern Finland, during fourteen months long period. Consumption parameters measured were the consumptions of district heat, electricity and water. Indoor parameters gathered were temperature, relative humidity (RH), the concentrations of carbon dioxide (CO2) and carbon monoxide (CO) and differential air pressure. In this study, self-organizing map (SOM) and Sammon's mapping were applied to resolve the effects of energy consumption on indoor air quality. Namely, the SOM was qualified as a suitable method having a property to summarize the multivariable dependencies into easily observable two-dimensional map. Accompanying that, the Sammon's mapping method was used to cluster pre-processed data to find similarities of the variables, expressing distances and groups in the data. The methods used were able to distinguish 7 different clusters characterizing indoor air quality and energy efficiency in the study house. The results indicate, that the cost implications in euros of heating and electricity energy vary according to the differential pressure, concentration of carbon dioxide, temperature and season.
Abstract: The theatre-auditorium under investigation following
the highly reflective characteristics of materials used in it (marble,
painted wood, smooth plaster, etc), architectural and structural
features of the Protocol and its intended use (very multifunctional:
Auditorium, theatre, cinema, musicals, conference room) from the
analysis of the statement of fact made by the acoustic simulation
software Ramsete and supported by data obtained through a
campaign of acoustic measurements of the state of fact made on the
spot by a Fonomet Svantek model SVAN 957, appears to be
acoustically inadequate. After the completion of the 3D model
according to the specifications necessary software used forecast in
order to be recognized by him, have made three simulations, acoustic
simulation of the state of and acoustic simulation of two design
solutions.
Improved noise characteristics found in the first design solution,
compared to the state in fact consists therefore in lowering
Reverberation Time that you turn most desirable value, while the
Indicators of Clarity, the Baricentric Time, the Lateral Efficiency,
Ratio of Low Tmedia BR and defined the Speech Intelligibility
improved significantly. Improved noise characteristics found instead
in the second design solution, as compared to first design solution, is
finally mostly in a more uniform distribution of Leq and in lowering
Reverberation Time that you turn the optimum values. Indicators of
Clarity, and the Lateral Efficiency improve further but at the expense
of a value slightly worse than the BR. Slightly vary the remaining
indices.
Abstract: The objective of this contribution is to study the
performances in terms of bit error rate, of space-time code algorithms
applied to MIMO communication in tunnels. Indeed, the channel
characteristics in a tunnel are quite different than those of urban or
indoor environment, due to the guiding effect of the tunnel.
Therefore, MIMO channel matrices have been measured in a straight
tunnel, in a frequency band around 3GHz. Correlation between array
elements and properties of the MIMO matrices are first studied as a
function of the distance between the transmitter and the receiver.
Then, owing to a software tool simulating the link, predicted values
of bit error rate are given for VLAST, OSTBC and QSTBC
algorithms applied to a MIMO configuration with 2 or 4 array
elements. Results are interpreted from the analysis of the channel
properties.
Abstract: power-line networks are promise infrastructure for
broadband services provision to end users. However, the network
performance is affected by stochastic channel changing which is due
to load impedances, number of branches and branched line lengths. It
has been proposed that multi-carrier modulations techniques such as
orthogonal frequency division multiplexing (OFDM), Multi-Carrier
Spread Spectrum (MC-SS), wavelet OFDM can be used in such
environment. This paper investigates the performance of different
indoor topologies of power-line networks that uses MC-SS
modulation scheme.It is observed that when a branch is added in the
link between sending and receiving end of an indoor channel an
average of 2.5dB power loss is found. In additional, when the branch
is added at a node an average of 1dB power loss is found.
Additionally when the terminal impedances of the branch change
from line characteristic impedance to impedance either higher or
lower values the channel performances were tremendously improved.
For example changing terminal load from characteristic impedance
(85 .) to 5 . the signal to noise ratio (SNR) required to attain the
same performances were decreased from 37dB to 24dB respectively.
Also, changing the terminal load from channel characteristic
impedance (85 .) to very higher impedance (1600 .) the SNR
required to maintain the same performances were decreased from
37dB to 23dB. The result concludes that MC-SS performs better
compared with OFDM techniques in all aspects and especially when
the channel is terminated in either higher or lower impedances.
Abstract: Offset Double-Disk Opener (DDO) is a popular
furrow opener in conservation tillage. It has some limitations such as
negative suction to penetrate in the soil, hair pinning and mixing seed
and fertilizer in the slot. Because of importance of separation of seed
and fertilizer in the slot, by adding two horizontal mini disks to DDO
a modified opener was made (MDO) which placed the fertilizer
between and under two rows of seed. To consider performance of
novel opener an indoor comparison test between DDO and MDO was
performed at soil bin. The experiment was conducted with three
working speeds (3, 6 and 8 km h-1), two bulk densities of soil (1.1
and 1.4 Mg m-3) and two levels of residues (1 and 2 ton ha-1). The
experimental design consisted in a (3×2×2) complete randomized
factorial with three replicates for each test. Moisture of seed furrow,
separation of seed and fertilizer, hair pinning and resultant forces
acting on the openers were used as assessing indexes. There was no
significant difference between soil moisture content in slots created
by DDO and MDO at 0-4 cm depth, but at 4-8 cm the in the slot
created by MDO moisture content was higher about 9%. Horizontal
force for both openers increased with increasing speed and soil bulk
density. Vertical force for DDO was negative so it needed additional
weight for penetrating in the soil, but vertical force for MDO was
positive and, which can solve the challenge of penetration in the soil
in DDO. In soft soil with heavy residues some trash was pushed by
DDO into seed furrow (hair pinning) but at MDO seed were placed at
clean groove. Lateral and vertical separation of seed and fertilizer
was performed effectively by MDO (4.5 and 5 cm, respectively)
while DDO put seed and fertilizer close to each other. Overall, the
Modified Offset Double-disks (MDO) had better performance. So by
adapting this opener with no-tillage drillers it would possible to have
higher yield in conservation tillage where the most appropriate
opener is disk type.
Abstract: The measurements of 226Ra, 232Th and 40K using
gamma spectrometry and radon concentration and exhalation rates
measurements using solid state nuclear track (LR-115, Type-II
plastic) detectors are used to asses a first order exposure risk for the
persons residing in Fatehbad and Hissar districts of Western Haryana,
India. The concentration of Radium, Thorium and Potassium in the
soil samples varies from 13.37 Bq m-3 to 24.67 Bq m-3, 34.67 Bq m-3
to 67.34 Bq m-3 and 298.78 Bq m-3 to 405.67 Bq m-3 respectively
with average values of 18.78, 47.35 and 361.57 Bq m-3 respectively.
The radium equivalent activity (Raeq) calculated for the same soil
samples varies from 92.72 Bq m-3 to 140.6 Bq m-3 with an average
value of 111.80 Bq m-3. The values of absorbed dose and annual
effective dose (indoors and outdoors) are found to vary from 44.18
nGy h-1 to 65.23 nGy h-1, 0.22 mSv y-1 to 0.32 mSv y-1 and 0.05 mSv
y-1 to 0.08 mSv y-1 respectively. The radon concentration and
exhalation rates have also been reported. The radium equivalent
activities in all the soil samples were found to be lower than the limit
(370 Bq kg-1) set in the Organization for Economic Cooperation and
Development (OECD) report and the value of Hex in all the samples
is less than unity.
Abstract: Ability of accurate and reliable location estimation in
indoor environment is the key issue in developing great number of
context aware applications and Location Based Services (LBS).
Today, the most viable solution for localization is the Received
Signal Strength (RSS) fingerprinting based approach using wireless
local area network (WLAN). This paper presents two RSS
fingerprinting based approaches – first we employ widely used
WLAN based positioning as a reference system and then investigate
the possibility of using GSM signals for positioning. To compare
them, we developed a positioning system in real world environment,
where realistic RSS measurements were collected. Multi-Layer
Perceptron (MLP) neural network was used as the approximation
function that maps RSS fingerprints and locations. Experimental
results indicate advantage of WLAN based approach in the sense of
lower localization error compared to GSM based approach, but GSM
signal coverage by far outreaches WLAN coverage and for some
LBS services requiring less precise accuracy our results indicate that
GSM positioning can also be a viable solution.
Abstract: This paper describes WiPoD (Wireless Position
Detector) which is a pure software based location determination and
tracking (positioning) system. It uses empirical signal strength measurements from different wireless access points for mobile user
positioning. It is designed to determine the location of users having
802.11 enabled mobile devices in an 802.11 WLAN infrastructure
and track them in real time. WiPoD is the first main module in our
LBS (Location Based Services) framework. We tested K-Nearest
Neighbor and Triangulation algorithms to estimate the position of a
mobile user. We also give the analysis results of these algorithms for
real time operations. In this paper, we propose a supportable, i.e.
understandable, maintainable, scalable and portable wireless
positioning system architecture for an LBS framework. The WiPoD
software has a multithreaded structure and was designed and implemented with paying attention to supportability features and real-time constraints and using object oriented design principles. We also describe the real-time software design issues of a wireless positioning system which will be part of an LBS framework.
Abstract: The use of neural networks is popular in various
building applications such as prediction of heating load, ventilation
rate and indoor temperature. Significant is, that only few papers deal
with indoor carbon dioxide (CO2) prediction which is a very good
indicator of indoor air quality (IAQ). In this study, a data-driven
modelling method based on multilayer perceptron network for indoor
air carbon dioxide in an apartment building is developed.
Temperature and humidity measurements are used as input variables
to the network. Motivation for this study derives from the following
issues. First, measuring carbon dioxide is expensive and sensors
power consumptions is high and secondly, this leads to short
operating times of battery-powered sensors. The results show that
predicting CO2 concentration based on relative humidity and
temperature measurements, is difficult. Therefore, more additional
information is needed.
Abstract: This paper describes a segmentation algorithm based
on the cooperation of an optical flow estimation method with edge
detection and region growing procedures.
The proposed method has been developed as a pre-processing
stage to be used in methodologies and tools for video/image indexing
and retrieval by content. The addressed problem consists in
extracting whole objects from background for producing images of
single complete objects from videos or photos. The extracted images
are used for calculating the object visual features necessary for both
indexing and retrieval processes.
The first task of the algorithm exploits the cues from motion
analysis for moving area detection. Objects and background are then
refined using respectively edge detection and region growing
procedures. These tasks are iteratively performed until objects and
background are completely resolved.
The developed method has been applied to a variety of indoor and
outdoor scenes where objects of different type and shape are
represented on variously textured background.
Abstract: The experiment was conducted to study the effect of
rearing systems on fatty acid composition and cholesterol content of
Thai indigenous chicken meat. Three hundred and sixty chicks were
allocated to 2 different rearing systems: conventional, housing in an
indoor pen (5 birds/m2); free-range, housing in an indoor pen (5
birds/m2) with access to a grass paddock (1 bird/m2) from 8 wk of age
until slaughter. All birds were provided with the same diet during the
experimental period. At 16 wk of age, 24 birds per group were
slaughtered to evaluate the fatty acid composition and cholesterol
content of breast and thigh meat. The results showed that the
proportion of SFA, MUFA and PUFA in breast and thigh meat were
not different among groups (P>0.05). However, the proportion of n-3
fatty acids was higher and the ratio of n-6 to n-3 fatty acids was lower
in free-range system than in conventional system (P0.05). The data indicated that the free-range system
could increase the proportion of n-3 fatty acids, but no effect on
cholesterol content in Thai indigenous chicken meat.
Abstract: The main objective of this research is to synthesize silk fibroin fiber for indoor air particulate removal. Silk cocoons were de-gummed using 0.5 wt % Na2CO3 alkaline solutions at 90 Ó╣ìC for 60 mins, washed with distilled water, and dried at 80 Ó╣ìC for 3 hrs in a vacuum oven. Two sets of experiment were conducted to investigate the impacts of initial particulate matter (PM) concentration and that of air flow rate on the removal efficiency. Rice bran collected from a local rice mill in Ubonratchathani province was used as indoor air contaminant in this work. The morphology and physical properties of silk fibroin (SF) fiber were measured. The SEM revealed the deposition of PM on the used fiber. The PM removal efficiencies of 72.29 ± 3.03 % and 39.33 ± 1.99 % were obtained of PM10 and PM2.5, respectively, when using the initial PM concentration at 0.040 mg/m3 and 0.020 mg/m3 of PM10 and PM2.5, respectively, with the air flow rate of 5 L/min.
Abstract: There-s a lack in understanding the indoor climate of Malaysian residential. The assumption of traditional house could
provide the best indoor environment is too good to be true. This research is to understand indoor environment in three types of
Malaysian residential and thermo recorder TR72Ui were placed in
indoor spaces for measurement. There are huge differences of indoor
environment between housing types, and building material helps to control indoor climate. Traditional house indoor climate was similar to
the outdoor. Temperature in the bedroom of terrace and town houses were slightly higher than the living room. Indoor temperature was 2oC
lower in the rainy season than the hot season. It was hard to control
indoor humidity level in traditional house compared with terrace and
town house. As for conclusion, town house provides the best thermal
environment to the building occupants and can be improved with good
roof insulation.
Abstract: This paper presents results of measurements campaign
carried out at a carrier frequency of 24GHz with the help of TPLINK
router in indoor line-of-sight (LOS) scenarios. Firstly, the
radio wave propagation strategies are analyzed in some rooms with
router of point to point Ad hoc network. Then floor attenuation is
defined for 3 floors in experimental region. The free space model and
dual slope models are modified by considering the influence of
corridor conditions on each floor. Using these models, indoor signal
attenuation can be estimated in modeling of indoor radio wave
propagation. These results and modified models can also be used in
planning the networks of future personal communications services.