Abstract: In this study, inhibition of Microcystis aeruginosa by
antialgal alleochemical gramine, was studied by analyzing algal
metabolic activity (represented by esterase and total dehydrogenase
activities) and cell ultrastructure (showing morphological and
ultrastructure alterations using transmission electron microscopy and
DNA ladder analysis). After gramine exposure, esterase and total
dehydrogenase activities were increased firstly but decreased later. In
contrast with the controls, the cells exposed to gramine showed
apparent ultrastructure alterations with thylakoids in breakage,
phycobilins in decrease, lipid and cyanophycin granules abundant
firstly but dissolved afterwards, DNA in fragementation. The
occurrence of increase of metabolic activity and specific granules
reflected that the resistance of cellular response to gramine was
initiated. DNA fragementation associated with the increase of
metabolic activity and specific granules hinted that gramine caused M.
aeruginosa cells to initiate some morphotype of programmed cell
death.
Abstract: The present study conducted experimental investigation on combustion and emission characteristics of compression ignition engine using diesel as pilot fuel and methane, hydrogen and methane/hydrogen mixture as gaseous fuels at 1800 rev min-1. The effect of gaseous fuel on peak cylinder pressure and heat release is modest at low to medium loads. At high load, the high combustion temperature and high quantity of pilot fuel contribute to better combustion efficiency for all kinds of gaseous fuels and increases the peak cylinder pressure. Enrichment of hydrogen in methane gradually increases the peak cylinder pressure. The brake thermal efficiency increases with higher hydrogen fraction at lower loads. Hydrogen addition in methane contributed to a proportional reduction of CO/CO2/HC emission without penalty of NOx. For particulate emission, methane and hydrogen, could both suppress the particle emission. 30% hydrogen fraction in methane is observed to be best in reducing the particulate emission.
Abstract: Discharges in hydrogen, ignited by wire explosion, with current amplitude up to 1.5 MA were investigated. Channel diameter oscillations were observed on the photostreaks. Voltage and current curves correlated with the photostreaks. At initial gas pressure of 5-35 MPa the oscillation period was proportional to square root of atomic number of the initiating wire material. These oscillations were associated with aligned magnetic and gas-kinetic pressures. At initial pressure of 80-160 MPa acoustic pressure fluctuations on the discharge chamber wall were increased up to 150 MPa and there were the growth of voltage fluctuations on the discharge gap up to 3 kV simultaneously with it. In some experiments it was observed abrupt increase in the oscillation amplitude, which can be caused by the resonance of the acoustic oscillations in discharge chamber volume and the oscillations connected with alignment of the gaskinetic pressure and the magnetic pressure, as far as frequencies of these oscillations are close to each other in accordance with the estimates and the experimental data. Resonance of different type oscillations can produce energy density increasing in the discharge channel. Thus, the appropriate initial conditions in the experiment allow to increase the energy density in the discharge channel
Abstract: Soil microbial activity is adversely affected by pollutants such as heavy metals, antibiotics and pesticides. Organic amendments including sewage sludge, municipal compost and vermicompost are recently used to improve soil structure and fertility. But, these materials contain heavy metals including Pb, Cd, Zn, Ni and Cu that are toxic to soil microorganisms and may lead to occurrence of more tolerant microbes. Among these, Pb is the most abundant and has more negative effect on soil microbial ecology. In this study, Pb levels of 0, 100, 200, 300, 400 and 500 mg Pb [as Pb(NO3)2] per kg soil were added to the pots containing 2 kg of a loamy soil and incubated for 6 months at 25°C with soil moisture of - 0.3 MPa. Dehydrogenase activity of soil as a measure of microbial activity was determined on 15, 30, 90 and 180 days after incubation. Triphenyl tetrazolium chloride (TTC) was used as an electron acceptor in this assay. PICTs (IC50 values) were calculated for each Pb level and incubation time. Soil microbial activity was decreased by increasing Pb level during 30 days of incubation but the induced tolerance appeared on day 90 and thereafter. During 90 to 180 days of incubation, the PICT was gradually developed by increasing Pb level up to 200 mg kg-1, but the rate of enhancement was steeper at higher concentrations.
Abstract: The elimination of ranitidine (a pharmaceutical
compound) has been carried out in the presence of UV-C radiation.
After some preliminary experiments, it has been experienced the no
influence of the gas nature (air or oxygen) bubbled in photolytic
experiments. From simple photolysis experiments the quantum yield
of this compound has been determined. Two photolytic
approximation has been used, the linear source emission in parallel
planes and the point source emission in spherical planes. The
quantum yield obtained was in the proximity of 0.05 mol Einstein-1
regardless of the method used. Addition of free radical promoters
(hydrogen peroxide) increases the ranitidine removal rate while the
use of photocatalysts (TiO2) negatively affects the process.
Abstract: In this study, the possibility of using potato as a
substrate for glutamic acid production by Brevibacterium linens
was investigated. For preparation of fermentation medium, potato
was hydrolyzed by hydrochloridric acid. The medium contained
potato hydrolysate, tween 80, mineral solution, glucose, and
potassium hydrogen phosphate. The initial pH of the medium was
adjusted to 7-7.5. For achieving the optimum time with maximum
yield, the beakers containing the medium and the inoculums were
incubated in a rotary water bath flask shaker for one to five days.
Thin layer choromatography was used for quantitative and
qualitative assay of the glutamic acid produced. The results
revealed that as fermentation time increased, pH of the
fermentation medium significantly decreased (P
Abstract: Several different cements have been tested to evaluate
their potential to leach calcium, chromium and aluminum ions in soft
water environment. The research allows comparing some different
cements in order to the potential risk of water contamination. This
can be done only in the same environment. To reach the results in
reasonable short time intervals and to make heavy metals
measurements with high accuracy, demineralized water was used. In
this case the conditions of experiments are far away from the water
supply practice, but short time experiments and measurably high
concentrations of elements in the water solution are an important
advantage. Moreover leaching mechanisms can be recognized, our
experiments reported here refer to this kind of cements evaluation.
Abstract: In the present study, a procedure was developed to
determine the optimum reaction rate constants in generalized
Arrhenius form and optimized through the Nelder-Mead method. For
this purpose, a comprehensive mathematical model of a fixed bed
reactor for dehydrogenation of heavy paraffins over Pt–Sn/Al2O3
catalyst was developed. Utilizing appropriate kinetic rate expressions
for the main dehydrogenation reaction as well as side reactions and
catalyst deactivation, a detailed model for the radial flow reactor was
obtained. The reactor model composed of a set of partial differential
equations (PDE), ordinary differential equations (ODE) as well as
algebraic equations all of which were solved numerically to
determine variations in components- concentrations in term of mole
percents as a function of time and reactor radius. It was demonstrated
that most significant variations observed at the entrance of the bed
and the initial olefin production obtained was rather high. The
aforementioned method utilized a direct-search optimization
algorithm along with the numerical solution of the governing
differential equations. The usefulness and validity of the method was
demonstrated by comparing the predicted values of the kinetic
constants using the proposed method with a series of experimental
values reported in the literature for different systems.
Abstract: In this study, production possibilities of hydrogen and/or methane via SCWG from black grape residues have been investigated. For this aim, grape residues which remain as a byproduct of the wine making process have been used. Since utilization from grape residues is limited due to the high moisture content, supercritical water gasification is the most convenient method. The effect of the gasification temperature and type of catalyst on supercritical water gasification have been investigated. Gasification experiments were performed in a batch autoclave at four different temperatures 300, 400, 500 and 600°C. K2CO3 and Trona (NaHCO3.Na2CO3·2H2O) were used as catalyst. Real biomass types of black grape residues have been successfully gasified and the product gas (hydrogen, methane, carbon dioxide, carbon monoxide and a small amount of ethane and ethylene) were identified by using gas chromatography. A TOC analyzer was used to determine total organic carbon (TOC) content of aqueous phase. The amounts of carboxylic acids, aldehydes, ketones, furfurals and phenols present in the aqueous solutions were analyzed by high performance liquid chromatography. When the temperature increased from 300°C to 600°C, mol% of H2 in gas products increased. The presence of catalysts improves the hydrogen yield. Trona showed gasification activity to be similar to that of K2CO3. It may be concluded that the use of Trona instead of commercially produced catalysts, can be preferably used in the gasification of biomass in supercritical water.
Abstract: Natural gas is defined as gas obtained from a natural underground reservoir. It generally contains a large quantity of methane along with heavier hydrocarbons such as ethane, propane, isobutene, normal butane; also in the raw state it often contains a considerable amount of non hydrocarbons, such as nitrogen and the acid gases (carbon dioxide and hydrogen sulfide). The acid gases must be removed from natural gas before use. One of the processes witch are use in the industry to remove the acid gases from natural gas is the use of alkanolamine process. In this present paper, a simulation study for an industrial gas sweetening plant has been investigated. The aim of the study is to investigate the effect of using mixing amines as solvent on the gas treatment process using the software Hysys.
Abstract: A sequential treatment of ozonation followed by a
Fenton or photo-Fenton process, using black light lamps (365 nm) in
this latter case, has been applied to remove a mixture of
pharmaceutical compounds and the generated by-products both in
ultrapure and secondary treated wastewater. The scientifictechnological
innovation of this study stems from the in situ
generation of hydrogen peroxide from the direct ozonation of
pharmaceuticals, and can later be used in the application of Fenton
and photo-Fenton processes. The compounds selected as models
were sulfamethoxazol and acetaminophen. It should be remarked that
the use of a second process is necessary as a result of the low
mineralization yield reached by the exclusive application of ozone.
Therefore, the influence of the water matrix has been studied in terms
of hydrogen peroxide concentration, individual compound
concentration and total organic carbon removed. Moreover, the
concentration of different iron species in solution has been measured.
Abstract: A kinetic model for propane dehydrogenation in an
industrial moving bed reactor is developed based on the reported
reaction scheme. The kinetic parameters and activity constant are
fine tuned with several sets of balanced plant data. Plant data at
different operating conditions is applied to validate the model and
the results show a good agreement between the model
predictions and plant observations in terms of the amount of main
product, propylene produced. The simulation analysis of key
variables such as inlet temperature of each reactor (Tinrx) and
hydrogen to total hydrocarbon ratio (H2/THC) affecting process
performance is performed to identify the operating condition to
maximize the production of propylene. Within the range of operating
conditions applied in the present studies, the operating condition to
maximize the propylene production at the same weighted average
inlet temperature (WAIT) is ΔTinrx1= -2, ΔTinrx2= +1, ΔTinrx3= +1 ,
ΔTinrx4= +2 and ΔH2/THC= -0.02. Under this condition, the surplus
propylene produced is 7.07 tons/day as compared with base case.
Abstract: Forty-five dairy cows were used to compare the
enzyme activity of alkaline phosphatase (ALP), lactate
dehydrogenase (LDH), α -amylase in the cervical mucus of cows
during spontaneous and induced estrus using progestagen or PGF2 α
and to determine whether these enzymes affect the fertility in cows
with induced estrus, at the time of Al. The animals were assigned to 3
groups (no treatment, a Crestar® for 12 days, a double im injection of
PGF2 α). The cows were artificially inseminated (AI). Cervical
mucus samples were collected from all cows 3 to 5 min before the
AI. The results are summarized as follows: ALP and α -amylase
activity for spontaneous estrus were similar to those for induced
estrus (P>0.05) . LDH activity levels during spontaneous and PGF2 α
induced estrus was significantly lower (P < 0.001) than that in
progestagene induced estrus groups. While no difference was found
between the first and the third groups. Our result showed a significant
difference in LDH activity levels between cows conceived with 2 or
more AI and those conceived with 1 AI. The result of this study
showed that the enzyme activity in cervical mucus is helpful for
detection of ovulation and time of AI.
Abstract: Biomass is becoming a large renewable resource for
power generation; it is involved in higher frequency in
environmentally clean processes, and even it is used for biofuels
preparation. On the other hand, hydrogen – other energy source – can
be produced in a variety of methods including gasification of
biomass. In this study, the production of hydrogen by gasification of
biomass waste is examined. This work explores the production of a
gaseous mixture with high power potential from Amazonas´ specie
known as copoazu, using a counter-flow fixed-bed bioreactor.
Abstract: Hydrogen that used as fuel in fuel cell vehicles can be
produced from renewable sources such as wind, solar, and hydro
technologies. PV-electrolyzer is one of the promising methods to
produce hydrogen with zero pollution emission. Hydrogen
production from a PV-electrolyzer system depends on the efficiency
of the electrolyzer and photovoltaic array, and sun irradiance at that
site. In this study, the amount of hydrogen is obtained using
mathematical equations for difference driving distance and sun peak
hours. The results show that the minimum of 99 PV modules are used
to generate 1.75 kgH2 per day for two vehicles.
Abstract: It is estimated that the total cost of abnormal
conditions to US process industries is around $20 billion dollars in
annual losses. The hydrotreatment (HDT) of diesel fuel in petroleum
refineries is a conversion process that leads to high profitable
economical returns. However, this is a difficult process to control
because it is operated continuously, with high hydrogen pressures
and it is also subject to disturbances in feed properties and catalyst
performance. So, the automatic detection of fault and diagnosis plays
an important role in this context. In this work, a hybrid approach
based on neural networks together with a pos-processing
classification algorithm is used to detect faults in a simulated HDT
unit. Nine classes (8 faults and the normal operation) were correctly
classified using the proposed approach in a maximum time of 5
minutes, based on on-line data process measurements.
Abstract: Fertilization plays an important role in crop growth and soil improvement. This study was conducted to determine the best fertilization system for wheat production. Experiments were arranged in a complete block design with three replications in two years. Main plots consisted of six methods of fertilization including (N1): farmyard manure; (N2): compost; (N3): chemical fertilizers; (N4): farmyard manure + compost; (N5): farmyard manure + compost + chemical fertilizers and (N6): control were arranged in sub plots. The addition of compost or farm yard manure significantly increased the soil microbial biomass carbon in comparison to the chemical fertilizer. The dehydrogenase, phosphatase and urease activities in the N3 treatment were significantly lower than in the farm yard manure and compost treatments.
Abstract: Solidification cracking and hydrogen cracking are some defects generated in the fusion welding of ultrahigh carbon steels. However, friction stir welding (FSW) of such steels, being a solid-state technique, has been demonstrated to alleviate such problems encountered in traditional welding. FSW include different process parameters that must be carefully defined prior processing. These parameters included but not restricted to: tool feed, tool RPM, tool geometry, tool tilt angle. These parameters form a key factor behind avoiding warm holes and voids behind the tool and in achieving a defect-free weld. More importantly, these parameters directly affect the microstructure of the weld and hence the final mechanical properties of weld. For that, 3D finite element (FE) thermo-mechanical model was developed using DEFORM 3D to simulate FSW of carbon steel. At points of interest in the joint, tracking is done for history of critical state variables such as temperature, stresses, and strain rates. Typical results found include the ability to simulate different weld zones. Simulations predictions were successfully compared to experimental FSW tests. It is believed that such a numerical model can be used to optimize FSW processing parameters to favor desirable defect free weld with better mechanical properties.
Abstract: The C3 plants are frequently suffering from exposure
to high temperature stress which limits the growth and yield of these
plants. This study seeks to clarify the physiological mechanisms of
heat tolerance in relation to oxidative stress in C3 species. Fifteen C3
species were exposed to prolonged moderately high temperature
stress 36/30°C for 40 days in a growth chamber. Chlorophyll
fluorescence (Fv/Fm) showed great difference among species at 40
days of the stress. The species showed decreases in Fv/Fm and
increases in malondialdehyde (MDA) content under stress condition
as well as negative correlation between Fv/Fm and MDA (r = -0.61*)
at 40 days of the stress. Hydrogen peroxide (H2O2) content before
and after stress in addition to its response under stress showed great
differences among species. The results suggest that the difference in
heat tolerance among C3 species is closely associated with the ability
to suppress oxidative damage but not with the content of reactive
oxygen species (ROS) which is regulated by complex network.
Abstract: Perturbed-Chain Statistical Association Fluid Theory (PC-SAFT) equation of state (EOS) is a modified SAFT EOS with three pure component specific parameters: segment number (m), diameter (σ) and energy (ε). These PC-SAFT parameters need to be determined for each component under the conditions of interest by fitting experimental data, such as vapor pressure, density or heat capacity. PC-SAFT parameters for propane, ethylene and hydrogen in supercritical region were successfully estimated by fitting experimental density data available in literature. The regressed PCSAFT parameters were compared with the literature values by means of estimating pure component density and calculating average absolute deviation between the estimated and experimental density values. PC-SAFT parameters available in literature especially for ethylene and hydrogen estimated density in supercritical region reasonably well. However, the regressed PC-SAFT parameters performed better in supercritical region than the PC-SAFT parameters from literature.