Abstract: A Finite Element (FE) based scheme is presented
for quantifying guided wave interaction with Localised Nonlinear
Structural Damage (LNSD) within structures of arbitrary layering
and geometric complexity. The through-thickness mode-shape of the
structure is obtained through a wave and finite element method. This
is applied in a time domain FE simulation in order to generate
time harmonic excitation for a specific wave mode. Interaction of
the wave with LNSD within the system is computed through an
element activation and deactivation iteration. The scheme is validated
against experimental measurements and a WFE-FE methodology for
calculating wave interaction with damage. Case studies for guided
wave interaction with crack and delamination are presented to verify
the robustness of the proposed method in classifying and identifying
damage.
Abstract: Stainless steel pipelines are crucial components to transportation and storage in the oil and gas industry. However, the rise of random attacks and vandalism on these pipes for their valuable transport has led to more security and protection for incoming surface impacts. These surface impacts can lead to large global deformations of the pipe and place the pipe under strain, causing the eventual failure of the pipeline. Therefore, understanding how these surface impact loads affect the pipes is vital to improving the pipes’ security and protection. In this study, experimental test and finite element analysis (FEA) have been carried out on EN3B stainless steel specimens to study the impact behaviour. Low velocity impact tests at 9 m/s with 16 kg dome impactor was used to simulate for high momentum impact for localised failure. FEA models of clamped and deformable boundaries were modelled to study the effect of the boundaries on the pipes impact behaviour on its impact resistance, using experimental and FEA approach. Comparison of experimental and FE simulation shows good correlation to the deformable boundaries in order to validate the robustness of the FE model to be implemented in pipe models with complex anisotropic structure.
Abstract: Ultra-high-performance fiber reinforced concrete (UHPFRC) is a specially formulated cement-based composite characterized with an ultra-high compressive strength (fc’ = 240 MPa) and a low water-cement ratio (W/B= 0.2). With such material characteristics, UHPFRC is favored for the design and constructions of structures required high structural performance and slender geometries. Unlike conventional concrete, the structural performance of members manufactured with UHPFRC has not yet been fully studied, particularly, for UHPFRC columns with high slenderness. In this study, the behaviors of slender UHPFRC columns under concentric or eccentric load will be investigated both experimentally and numerically. Four slender UHPFRC columns were tested under eccentric loads with eccentricities, of 0 mm, 35 mm, 50 mm, and 85 mm, respectively, and one UHPFRC beam was tested under four-point bending. Finite element (FE) analysis was conducted with concrete damage plasticity (CDP) modulus to simulating the load-middle height or middle span deflection relationships and damage patterns of all UHPFRC members. Simulated results were compared against the experimental results and observation to gain the confidence of FE model, and this model was further extended to conduct parametric studies, which aim to investigate the effects of slenderness regarding failure modes and load-moment interaction relationships. Experimental results showed that the load bearing capacities of the slender columns reduced with an increase in eccentricity. Comparisons between load-middle height and middle span deflection relationships as well as damage patterns of all UHPFRC members obtained both experimentally and numerically demonstrated high accuracy of the FE simulations. Based on the available FE model, the following parametric study indicated that a further increase in the slenderness of column resulted in significant decreases in the load-bearing capacities, ductility index, and flexural bending capacities.
Abstract: Electromagnetic Interference (EMI) shielded doors made from brass extruded channels need to be welded with shielded enclosures to attain optimum shielding performance. Control of welding induced distortion is a problem in welding dissimilar metals like steel and brass. In this research, soldering of the steel-brass joint has been proposed to avoid weld distortion. The material used for brass channel is UNS C36000. The thickness of brass is defined by the manufacturing process, i.e. extrusion. The thickness of shielded enclosure material (ASTM A36) can be varied to produce joint between the dissimilar metals. Steel sections of different gauges are soldered using (91% tin, 9% zinc) solder to the brass, and strength of joint is measured by standard test procedures. It is observed that thin steel sheets produce a stronger bond with brass. The steel sections further require to be welded with shielded enclosure steel sheets through TIG welding process. Stresses and deformation in the vicinity of soldered portion is calculated through FE simulation. Crack formation in soldered area is also studied through experimental work. It has been found that in thin sheets deformation produced due to applied force is localized and has no effect on soldered joint area whereas in thick sheets profound cracks have been observed in soldered joint. The shielding effectiveness of EMI shielded door is compromised due to these cracks. The shielding effectiveness of the specimens is tested and results are compared.
Abstract: In the last years, the crashworthiness of an automotive body structure can be improved, since the beginning of the design stage, thanks to the development of specific optimization tools. It is well known how the finite element codes can help the designer to investigate the crashing performance of structures under dynamic impact. Therefore, by coupling nonlinear mathematical programming procedure and statistical techniques with FE simulations, it is possible to optimize the design with reduced number of analytical evaluations. In engineering applications, many optimization methods which are based on statistical techniques and utilize estimated models, called meta-models, are quickly spreading. A meta-model is an approximation of a detailed simulation model based on a dataset of input, identified by the design of experiments (DOE); the number of simulations needed to build it depends on the number of variables. Among the various types of meta-modeling techniques, Kriging method seems to be excellent in accuracy, robustness and efficiency compared to other ones when applied to crashworthiness optimization. Therefore the application of such meta-model was used in this work, in order to improve the structural optimization of a bumper for a racing car in composite material subjected to frontal impact. The specific energy absorption represents the objective function to maximize and the geometrical parameters subjected to some design constraints are the design variables. LS-DYNA codes were interfaced with LS-OPT tool in order to find the optimized solution, through the use of a domain reduction strategy. With the use of the Kriging meta-model the crashworthiness characteristic of the composite bumper was improved.
Abstract: This project was aimed at investigating the effect of velocity stacks on the intakes of internal combustion engines for motorsport applications. The intake systems in motorsport are predominantly fuel injection with a plate mounted for the stacks. Using Computational Fluid Dynamics software, the relationship between the stack length and power and torque delivery across the engine’s rev range was investigated and the results were used to choose the best option for its intended motorsport discipline. The test results are expected to vary with engine geometry and its natural manufacturer characteristics. The test was also relevant in bridging between computational data and real simulation as the results show flow, pressure and velocity readings but the behaviour of the engine is inferred from the nature of each test. The results of the data analysis were tested in a real-life simulation on a dynamometer to prove the theory of stack length on power and torque delivery, which helps determine the most suitable stack for the Vauxhall engine for rallying in the Caribbean.
Abstract: Interstitial free steels possess better formability and
have many applications in automotive industries. Forming limit
diagrams (FLDs) indicate the formability of materials which can be
determined by experimental and finite element (FE) simulations.
FLDs were determined experimentally by LDH test, utilizing optical
strain measurement system for measuring the strains in different
width specimens and by FE simulations in Interstitial Free (IF) and
Interstitial Free High Strength (IFHS) steels. In this study, the
experimental and FE simulated FLDs are compared and also the
stress based FLDs were investigated.
Abstract: Fracture in hot precision forging of engine valves was
investigated in this paper. The entire valve forging procedure was
described and the possible cause of the fracture was proposed. Finite
Element simulation was conducted for the forging process, with
commercial Finite Element code DEFORMTM. The effects of
material properties, the effect of strain rate and temperature were
considered in the FE simulation. Two fracture criteria were discussed
and compared, based on the accuracy and reliability of the FE
simulation results. The selected criterion predicted the fracture
location and shows the trend of damage increasing with good
accuracy, which matches the experimental observation. Additional
modification of the punch shapes was proposed to further reduce the
tendency of fracture in forging. Finite Element comparison shows a
great potential of such application in the mass production.
Abstract: Rotary draw bending is a method which is being used
in tube forming. In the tube bending process, the neutral axis moves
towards the inner arc and the wall thickness distribution changes for
tube’s cross section. Thinning takes place in the outer arc of the tube
(extrados) due to the stretching of the material, whereas thickening
occurs in the inner arc of the tube (intrados) due to the comparison of
the material. The calculations of the wall thickness distribution,
neutral axis shifting, and strain distribution have not been accurate
enough, so far. The previous model (the geometrical model)
describes the neutral axis shifting and wall thickness distribution. The
geometrical of the tube, bending radius and bending angle are
considered in the geometrical model, while the influence of the
material properties of the tube forming are ignored. The advanced
model is a modification of the previous model using material
properties that depends on the correction factor. The correction factor
is a purely empirically determined factor. The advanced model was
compared with the Finite element simulation (FE simulation) using a
different bending factor (Bf =bending radius/ diameter of the tube),
wall thickness (Wf = diameter of the tube/ wall thickness), and
material properties (strain hardening exponent). Finite element model
of rotary draw bending has been performed in PAM-TUBE program
(version: 2012). Results from the advanced model resemble the FE
simulation and the experimental test.
Abstract: Two micromechanical models for 3D smart composite
with embedded periodic or nearly periodic network of generally
orthotropic reinforcements and actuators are developed and applied to
cubic structures with unidirectional orientation of constituents.
Analytical formulas for the effective piezothermoelastic coefficients
are derived using the Asymptotic Homogenization Method (AHM).
Finite Element Analysis (FEA) is subsequently developed and used
to examine the aforementioned periodic 3D network reinforced smart
structures. The deformation responses from the FE simulations are
used to extract effective coefficients. The results from both
techniques are compared. This work considers piezoelectric materials
that respond linearly to changes in electric field, electric
displacement, mechanical stress and strain and thermal effects. This
combination of electric fields and thermo-mechanical response in
smart composite structures is characterized by piezoelectric and
thermal expansion coefficients. The problem is represented by unitcell
and the models are developed using the AHM and the FEA to
determine the effective piezoelectric and thermal expansion
coefficients. Each unit cell contains a number of orthotropic
inclusions in the form of structural reinforcements and actuators.
Using matrix representation of the coupled response of the unit cell,
the effective piezoelectric and thermal expansion coefficients are
calculated and compared with results of the asymptotic
homogenization method. A very good agreement is shown between
these two approaches.
Abstract: The substantial similarity of fatigue mechanism in a
new test rig for rolling contact fatigue (RCF) has been investigated. A
new reduced-scale test rig is designed to perform controlled RCF
tests in wheel-rail materials. The fatigue mechanism of the rig is
evaluated in this study using a combined finite element-fatigue
prediction approach. The influences of loading conditions on fatigue
crack initiation have been studied. Furthermore, the effects of some
artificial defects (squat-shape) on fatigue lives are examined. To
simulate the vehicle-track interaction by means of the test rig, a threedimensional
finite element (FE) model is built up. The nonlinear
material behaviour of the rail steel is modelled in the contact
interface. The results of FE simulations are combined with the critical
plane concept to determine the material points with the greatest
possibility of fatigue failure. Based on the stress-strain responses, by
employing of previously postulated criteria for fatigue crack initiation
(plastic shakedown and ratchetting), fatigue life analysis is carried
out. The results are reported for various loading conditions and
different defect sizes. Afterward, the cyclic mechanism of the test rig
is evaluated from the operational viewpoint. The results of fatigue
life predictions are compared with the expected number of cycles of
the test rig by its cyclic nature. Finally, the estimative duration of the
experiments until fatigue crack initiation is roughly determined.
Abstract: There are several types of metal-based devices conceived as dampers for the seismic energy absorber whereby damages to the major structural components could be minimized for both new and existing structures. This paper aimed to develop and evaluate structural performance of slit circular shear panel damper for passive seismic energy protection by inelastic deformation. Structural evaluation was done using commercially available nonlinear FE simulation program. The main parameters considered are: diameter-to-thickness (D/t) ratio and slit length-to-width ratio (l/w). Depending on these parameters three different buckling mode and hysteretic behavior was found: yielding prior to buckling without strength degradation, yielding prior to buckling with strength degradation and yielding with buckling and strength degradation which forms pinching at initial displacement. The susceptible location at which the possible crack is initiated is also identified for selected specimens using rupture index.
Abstract: The idea of adding metallic energy dissipaters to a structure to absorb a large part of the seismic energy began four decades ago. There are several types of metal-based devices conceived as dampers for the seismic energy absorber whereby damages to the major structural components could be minimized for both new and existing structures. This paper aimed to develop and evaluate structural performance of both stiffened and non stiffened circular shear panel damper for passive seismic energy protection by inelastic deformation. Structural evaluation was done using commercially available nonlinear FE simulation program. Diameter-to-thickness ratio is employed as main parameter to investigate the hysteresis performance of stiffened and unstiffened circular shear panel. Depending on these parameters three different buckling mode and hysteretic behavior was found: yielding prior to buckling without strength degradation, yielding prior to buckling with strength degradation and yielding with buckling and strength degradation which forms pinching at initial displacement. Hence, the hysteresis behavior is identified, specimens which deform without strength degradation so it will be used as passive energy dissipating device in civil engineering structures.
Abstract: Tailor Welded Blanks (TWB) are utilized in automotive industries widely because of their advantage of weight and cost reduction and maintaining required strength and structural integrity. TWB consist of two or more sheet having dissimilar or similar material and thickness; welded together to form a single sheet before forming it to desired shape. Forming of the tailor welded blank is affected by ratio of thickness of blanks, ratio of their strength, etc. mainly due to in-homogeneity of material. In the present work the relative effect of these parameters on weld line movement is studied during deep drawing of TWB using FE simulation using HYPERWORKS. The simulation is validated with results from the literature. Simulations were than performed based on Taguchi orthogonal array followed by the ANOVA analysis to determine the significance of these parameters on forming of TWB.
Abstract: The fracture performance of steel wires for civil engineering applications remains a major concern in civil engineering construction and maintenance of wire reinforced structures. The need to employ approaches that simulate micromechanical material processes which characterizes fracture in civil structures has been emphasized recently in the literature. However, choosing from the numerous micromechanics-based fracture models, and identifying their applicability and reliability remains an issue that still needs to be addressed in a greater depth. Laboratory tensile testing and finite element tensile testing simulations with the shear, ductile and Gurson-Tvergaard-Needleman’s micromechanics-based models conducted in this work reveal that the shear fracture model is an appropriate fracture model to predict the fracture performance of steel wires used for civil engineering applications. The need to consider the capability of the micromechanics-based fracture model to predict the “cup and cone” fracture exhibited by the wire in choosing the appropriate fracture model is demonstrated.
Abstract: This paper presents the simulation of fragmentation
warhead using a hydrocode, Autodyn. The goal of this research is to
determine the lethal range of such a warhead. This study investigates
the lethal range of warheads with and without steel balls as
preformed fragments. The results from the FE simulation, i.e. initial
velocities and ejected spray angles of fragments, are further processed
using an analytical approach so as to determine a fragment hit density
and probability of kill of a modelled warhead. In order to simulate a
plenty of preformed fragments inside a warhead, the model requires
expensive computation resources. Therefore, this study attempts to
model the problem in an alternative approach by considering an
equivalent mass of preformed fragments to the mass of warhead
casing. This approach yields approximately 7% and 20% difference
of fragment velocities from the analytical results for one and two
layers of preformed fragments, respectively. The lethal ranges of the
simulated warheads are 42.6 m and 56.5 m for warheads with one and
two layers of preformed fragments, respectively, compared to 13.85
m for a warhead without preformed fragment. These lethal ranges are
based on the requirement of fragment hit density. The lethal ranges
which are based on the probability of kill are 27.5 m, 61 m and 70 m
for warheads with no preformed fragment, one and two layers of
preformed fragments, respectively.
Abstract: In recent years asymmetric cross section aluminum
alloy stock has been finding increasing use in various industrial manufacturing areas such as general structures and automotive
components. In these areas, components are generally required to have
complex curved configuration and, as such, a bending process is required during manufacture. Undesirable deformation in bending
processes such as flattening or wrinkling can easily occur when thin-walled sections are bent. Hence, a thorough understanding of the
bending behavior of such sections is needed to prevent these undesirable deformations. In this study, the bending behavior of
asymmetric channel section was examined using finite element analysis (FEA). Typical methods of preventing undesirable
deformation, such as asymmetric laminated elastic mandrels were included in FEA model of draw bending. Additionally, axial tension
was applied to prevent wrinkling. By utilizing the FE simulations effect of restriction dies and axial tension on undesirable deformation during the process was clarified.